金属有机物化学气相法制备YBCO超导薄膜研究

运用金属有机物化学气相沉积法(MOCVD),在LaAlO3(LAO)单晶上沉积YBa2Cu3O7-x(YBCO)超导薄膜。通过使用优化的进液装置,使金属有机源连续、稳定地输送至蒸发皿进行闪蒸。通过优化总气压、氧分压等生长条件,获得高质量的YBCO薄膜。在固定的温度条件下,调节反应总气压和氧分压,在总压为380Pa,氧分压为180Pa获得YBCO薄膜临界电流密度Jc=0.6MA/cm2。随着氧分压增大,YBCO薄膜产生a轴取向,(005)峰向左偏移,且薄膜中的Cu/Ba由1.0变化至1.63。在Cu/Ba=1.48时,YBCO薄膜结构与性能较优。     

高温热处理气氛对低氟MOD法制备YBCO超导薄膜的影响研究

金属有机物沉积法(MOD)制备YBa2Cu3O7-x(YBCO)涂层导体是最具有商业前景的方法之一.本文使用环烷酸铜代替三氟乙酸铜,降低了前驱液中大约50%的氟含量.然后在带有缓冲层(Y2O3/YSZ/CeO2)的Ni-5at.%W基带上采用MOD法制备了YBCO薄膜并系统研究了高温热处理过程中气体流速和氧分压对YBC...     

瞬态液相辅助的 YBa2Cu3O7-δ 超导薄膜快速成相及界面反应

高温超导涂层导体因其良好的强电强磁应用前景备受关注. 本文在无氟金属有机沉积(FF-MOD) 工艺中, 通过快速将低氧压气氛切换到高氧压(p O2 ) , 实现了 YBa2Cu3 O7 -δ (YBCO) 薄膜在 LaMnO3 (LMO)/IBADMgO/Y2 O3/Al2 O3/Hastelloy 衬底上的瞬态液相和高速外延生长. 研究了快速成相的氧分压和最高晶化温度的影响, 关注超导薄膜与种籽层之间的界面反应而产生的 BaMnO3 (BMO) 异质相, 对 BMO 的成核和生长机制进行了研究, 分析了 BMO 含量对 YBCO 薄膜织构与超导性能的影响. 结果表明低晶化温度、 低氧分压气氛能够有效抑制BMO 的形成, 而低含量 BMO、 强c 轴取向有利于获得高性能的 YBCO 薄膜.     

YBa2 Cu3 O7-δ/SrNb0.01 Ti0.99 O3 p-n结的制备及其特性

采用脉冲激光沉积技术,在n型SrNb0.01Ti0.99O3(SNTO)单晶基片上生长p型YBa2Cu3O7-δ(YBCO)薄膜,制备出YBCO/SNTO p-n结.YBCO薄膜是高度c轴织构的超导薄膜,且具有良好的超导电性.YBCO/SNTO p-n结具有较好的整流特性和很好的温度与磁场稳定性.     

YBa2Cu3O7－δ/SrNb0.01Ti0.99O3 p-n结的制备及其特性

采用脉冲激光沉积技术，在n型SrNb001Ti099O3(SNTO)单晶基片上生长p型YBa2Cu3O7-δ(YBCO)薄膜，制备出YBCO/SNTO p n结.YBCO薄膜是高度c轴织构的超导薄膜，且具有良好的超导电性.YBCO/SNTO p n结具有较好的整流特性和很好的温度与磁场稳定性. 关键词： YBa2Cu3O7-δ SrNb001Ti099O3 p n结     

前驱液成分对TFA-MOD法制备YBa2Cu3O7-x薄膜超导性能的影响

采用三氟乙酸盐-金属有机沉积法(TFA-MOD)在铝酸镧单晶基体上制备了YBa₂Cu₃O_7-x (YBCO)超导薄膜.通过改变前驱液的成分,研究了金属元素的不同化学计量比对YBCO薄膜的结构和性能的影响.结果表明,按照钇盐Y(CH₃COO)₃与钡盐Ba(CH₃COO)₂的比例为Y ∶Ba=1 ∶1.5时所制备的YBCO薄膜的临界电流密度比严 关键词： 三氟乙酸盐-金属有机沉积 钇钡铜氧薄膜 前驱液成分 磁通钉扎     

Y_2O_3缓冲层对YBCO超导转变温度的影响（英文）

超导薄膜所受的应力对其临界转变温度Tc具有重要的影响,研究应力对超导薄膜Tc的影响对获得更高Tc材料具有重要意义.本文采用溶胶-凝胶法,在LAO单晶基板上制备了Y2O3/YBCO薄膜,并研究了Y2O3缓冲层对不同厚度YBCO超导薄膜的临界转变温度的影响.研究发现,当YBCO薄膜厚度为90nm时,由于Y2O3和YBCO薄膜的晶格错配,在YBCO/Y2O3薄膜的a-b面内引入了压应力,增加了c轴的晶格常数,结果提高了YBCO薄膜的临界转变温度.当YBCO薄膜的厚度较大时(如230nm),由晶格错配引起的应力通过位错的形式得以释放,YBCO薄膜的Tc变化不大.     

掺杂Y2O3和BaCeO3提高MOD-YBCO超导性能的研究

本文通过在前驱液中添加过量钇盐和铈的有机盐,采用三氟乙酸盐-金属有机沉积法(TFA-MOD) 在铝酸镧单晶基体上制备了含有纳米氧化钇和纳米铈酸钡的YBCO薄膜. 与纯YBCO薄膜相比,掺杂Y₂O₃/BaCeO₃的YBCO膜的临界转变温度几乎保持不变,为91 K左右. 而掺杂Y₂O₃/BaCeO₃的YBCO膜的临界电流密度达到5.0 MA/cm² (77 K, 0T), 是纯YBCO膜临界电流密度的1.5倍.薄膜中的Y₂O₃和BaCeO₃可能在YBCO内部起到了 有效的钉扎磁通作用. 关键词： 钇钡铜氧薄膜 2O₃和纳米BaCeO₃')" href="#">纳米Y₂O₃和纳米BaCeO₃ 磁通钉扎 三氟乙酸盐-金属有机沉积     

快速前处理TFA-MOD制备YBCO超导薄膜的研究

三氟乙酸盐金属有机物沉积(TFA-MOD)方法是制备YBa2Cu3O7(YBCO)超导薄膜最有应用前景的方法之一。采用快速前处理TFA-MOD的方法在LaAlO3单晶基片上生长YBCO薄膜并与常规的TFA-MOD方法进行对比研究。XRD分析表明用快速前处理TFA-MOD方法制备的YBCO薄膜的c轴取向一致性,没有常规的TFA-MOD制备的YBCO薄膜好。SEM的分析表明快速前处理TFA-MOD制备的YBCO超导薄膜表面有孔洞和YBCO(103)取向生长的晶粒,常规方法制备的YBCO薄膜表面比较光滑,孔洞较少。虽然较常规方法制备的薄膜的临界电流密度(JC)低,但超导电性能分析表明,快速前处理方法制备的YBCO薄膜JC达到1mA/cm2以上,且前处理时间大幅缩短,对于提高YBCO薄膜制备的效率非常有效。     

用于MOCVD的金属有机Ba源的制备及性质研究北大核心CSCD

金属有机化学气相沉积法(MOCVD)能够在长的柔性金属基带上连续、快速、均匀沉积YBa2Cu3O7-δ(YBCO)薄膜,因而极具开发价值.MOCVD制备YBCO涂层导体的关键技术之一在于金属有机源(MO)的制备.国外化学试剂公司在以2,2,6,6-4甲基-3,5庚二酮(thd)为配体的MO源上技术较为成熟,并已实现商业化生产,但是价格昂贵,其中Ba(thd)2价格约为700元/g.另外,与Y(thd)3和Cu(thd)2相比,Ba(thd)2挥发性、稳定性差且制备困难.本文对金属有机Ba源的制备、稳定性及真空下的蒸发特性进行了研究.通过引入助配体四乙烯基戊胺,该Ba源的蒸发温度比纯的Ba(thd)2更低,稳定性更高,且成本仅为30元/g,对于降低YBCO高温超导带材的制备成本具有重要意义.采用该Ba源制备的300nm厚YBCO薄膜的Jc达到2.0MA/cm2(77K,0T),表明其具有很好的实用性.     

退火氧压对YBa2Cu3O7-x薄膜中的激光感生热电电压效应的影响

测量了在不同氧压下退火生长的YBa₂Cu₃O_7-x(YBCO)薄膜中的激光感生热电电压(LITV)信号,发现随退火氧压的增大可使LITV信号的峰值有2—4倍的增强,并且变化趋势与薄膜热电势的各向异性随氧含量的变化规律相同.波长在473—808nm范围内的连续激光辐照,在5000Pa的氧压下退火生长的YBCO薄膜中探测到的LITV信号最大;而紫外脉冲激光辐照时,LITV信号的最大值出现在退火氧压为10⁵Pa 关键词： 2Cu₃O_7-x薄膜')" href="#">YBa₂Cu₃O_7-x薄膜 激光感生热电电压 各向异性的Seebeck系数 氧含量     

Strongly enhanced flux pinning in the YBa_2Cu_3O_(7-X) films with the co-doping of Ba TiO_3 nanorod and Y_2O_3 nanoparticles at 65 K

YBa2Cu3O7-x(YBCO) films with co-doping BaTiO3(BTO) and Y2O3 nanostructures were prepared by metal organic deposition using trifluoroacetates(TFA-MOD). The properties of the BTO/Y2O3co-doped YBCO films with different excess yttrium have been systematically studied by x-ray diffraction(XRD), Raman spectra, and scanning electron microscope(SEM). The optimized content of yttrium excess in the BTO/Y2O3co-doped YBCO films is 10 mol.%, and the critical current density is as high as ~ 17 mA/cm2(self-field, 65 K) by the magnetic signal. In addition, the Y2Cu2O5 was formed when the content of yttrium excess increases to 24 mol.%, which may result in the deterioration of the superconducting properties and the microstructure. The unique combination of the different types of nanostructures of BTO and Y2O3 in the doped YBCO films, compared with the pure YBCO films and BTO doped YBCO films, enhances the critical current density(JC) not only at the self-magnetic field, but also in the applied magnetic field.     

电化学法涂层导体CeO_2缓冲层外延生长研究

电化学沉积法制备高温超导YBa2Cu3O7-δ涂层导体缓冲层具有工艺简单、设备要求低、易于连续化批量制备等优点。采用电化学沉积法,在双轴织构的Ni-5at.%W(Ni-5W)金属基带上成功制备出了具有良好c轴取向的CeO2缓冲层薄膜。利用X射线衍射、极图、扫描电子显微镜和原子力显微镜等对上述氧化物薄膜的织构、表面形貌等进行表征。重点研究了薄膜厚度、退火温度、退火时间等工艺对薄膜外延生长及其表面形貌的影响,结果表明:电化学沉积方法制备的CeO2缓冲层具有很好的双轴织构、表面平整、均一,粗糙度低,表现出良好的缓冲层性质。结合金属有机化学溶液超导层的制备技术,本工作展示了一条全化学法制备第二代高温超导带材的技术路线,具有很好的应用前景。     

蓝宝石基片上制备双面Tl_2Ba_2CaCu_2O_8超导薄膜

在蓝宝石基片上,以CeO2为缓冲层制备了高质量的双面Tl2Ba2CaCu2O8(Tl-2212)超导薄膜。以金属铈靶作为溅射源生长了c轴取向的CeO2缓冲薄膜,并对CeO2薄膜进行了高温处理,有效改善了其结晶质量和表面形貌。采用两步法制备了双面的Tl-2212超导薄膜。XRD测试显示,薄膜为纯的Tl-2212相,且其晶格c轴垂直于衬底表面。超导薄膜的Tc为106K,Jc(77K,0T)为3.5MA/cm2,微波表面电阻Rs(77K,10GHz)为390μΩ。     

利用微带谐振技术研究MgB_2/Al_2O_3和YBa_2Cu_3O_(7-x)/LaAlO_3超导薄膜的微波性质(英文)

利用微带谐振技术研究了MgB2/A12O3和YBa2Cu3o7-X/LaAlO3(YBCO/LAO)超导薄膜的微波性质.一个颗粒尺寸模型被用来分析超导薄膜的穿透深度和表面电阻.结果表明,对于高质的YBCO/LAO,微波性质主要由颗粒决定.对于低质的MgB2/Al2O3,该薄膜的微波性质主要由颗粒边界决定.     

Strong flux pinning enhancement in YBa2Cu3O7-x films by embedded BaZrO3 and BaTiO3 nanoparticles

YBa2Cu3O7-x (YBCO) films with embedded BaZrO3 and BaTiO3 nanoparticles were fabricated by metalorganic deposition using trifluoroacetates (TFA-MOD). Both X-ray diffraction and transmission electron microscopy revealed that these BaZrO3 and BaTiO3 nanoparticles had random orientations and were distributed stochastically in the YBCO matrix. The unique combined microstructure enhances the critical current density (Jc) of the BaZrO3/BaTiO3 doped-YBCO films, while keeping the critical transition temperature (Tc) close to that in the pure YBCO films. These results indicate that BaZrO3 and BaTiO3 nanoparticles provide strong flux pinning in YBCO films.     

Effect of different oxidizing gases on the in-situ growth of YBa2Cu3O7−δ films by pulsed laser deposition

The effectiveness of oxygen (O₂), nitrous oxide (N₂O), and nitrogen dioxide (NO₂) as oxidizing agents during in-situ growth of YBa₂Cu₃O_7−δ (YBCO) films on (100) SrTiO₃ substrates by pulsed laser deposition has been studied as a function of deposition temperature (700–800°C), and laser wavelength (193,248 and 355 nm), for a wide range of oxidizer gas pressure (0.1–200 mTorr). In general, the superconducting transition temperature of the films has been found to increase with increasing oxidant pressure, with zero-resistance temperature ≈90 K only obtained in films prepared in a relatively high pressure (150–200 mTorr) of oxidizer gas. At lower pressures, the transition temperature while being depressed is quite sensitive to the nature of the oxidant, the laser wavelength and the deposition temperature. Nevertheless, independent of the oxygen source or other growth parameters, an almost linear decrease in transition temperature with a corresponding increase in the c-axis lattice parameter has been observed for all the film. YBCO films have also been deposited in a low pressure background (≤ 1 mTorr) using a combination of atomic oxygen and pulsed molecular oxygen. The results are discussed in terms of the oxygen requirement for kinetic and thermodynamic stability of YBCO during growth of the film by pulsed laser deposition.     

Influence of oxygen pressure on critical current density and magnetic flux pinning structures in YBa2Cu3O7-x fabricated by chemical solution deposition

This paper studies the effect of oxygen partial pressure on the fabrication of YBa 2 Cu 3 O 7 x films on (00l) LaAlO 3 substrates by metalorganic deposition using trifluoroacetates (TFA-MOD).As the oxygen partial pressure increases to 1500 Pa,a great increase in the superconducting properties is observed at high magnetic fields parallel to the YBCO c axis.The cross-sectional transmission electron microscope images show that a high density of stacking faults in the size range of 10-15 nm may act as flux pinning centres to enhance the critical current density of the YBCO films