Synthesis and magnetic properties of single-crystalline BaFe12O19 nanoparticles

Rod-like and platelet-like nanoparticles of simple-crystalline barium hexaferrite (BaFe₁₂O₁₉) have been synthesized by the molten salt method. Both particle size and morphology change with the reaction temperature and time. The easy magnetization direction (0 0 l) of the BaFe₁₂O₁₉ nanoparticles has been observed directly by performing X-ray diffraction on powders aligned at 0.5 T magnetic field. The magnetic properties of the BaFe₁₂O₁₉ magnet were investigated with various sintering temperatures. The maximum values of saturation magnetization (σ_s=65.8 emu/g), remanent magnetization (σ_r=56 emu/g) and coercivity field (H_ic=5251 Oe) of the aligned samples occurred at the sintering temperatures of 1100 °C. These results indicate that BaFe₁₂O₁₉ nanoparticles synthesized by the molten salt method should enable detailed investigation of the size-dependent evolution of magnetism, microwave absorption, and realization of a nanodevice of magnetic media.     

Formation of submicron-sized SrFe12−xAlxO19 with very high coercivity

Submicron-sized SrFe_12−xAl_xO₁₉ (x=1.3) was formed in glass-ceramic matrix using controlled thermocrystallization of the SrO–Fe₂O₃–Al₂O₃–B₂O₃ glass and the hexaferrite powder was obtained by removing the matrix phases. The samples were characterized by X-ray diffraction, scanning electron microscopy with energy-dispersive X-ray (EDX) analysis and magnetization measurements. The glass-ceramic material exhibits very high coercivity value up to 10.18 kOe which approaches a theoretically estimated maximum value for the compound. The hexaferrite powder consists of well faceted single crystals, which adopt the shape of a truncated hexagonal bipyramid. The powder saturation magnetization value is close to the theoretically estimated one for bulk material. Crystal structure of the powder was refined by Rietveld method and distribution of Al atoms on Fe sites was determined. Al atoms occupy 41% of 2a sites, 14% of 12k sites and 5% of 4e(1/2) sites, while 4f sites are not affected.     

Evidence of existence of metastable SrFe12O19 nanoparticles

The existence of metastable hexaferrite is reported. Synthesis of strontium hexaferrite, SrFe₁₂O₁₉, at 400 °C was realized under controlled oxygen atmosphere. Such technique allows obtaining of SrFe₁₂O₁₉ at lower temperatures than those by traditional methods (above 800 °C). Phase transformation occurred during a measurement of magnetization vs. temperature (heating up to 625 °C). The heat treatment induces a change from SrFe₁₂O₁₉ to γ-Fe₂O₃ (as the main phase), and SrFeO_2.74 to Sr₂Fe₂O₅. Together with these phase transformations, an increment in the amount of SrCO₃ is detected. Magnetic study of the samples, before and after the heating, supports the structural analysis conclusions.     

Synthesis and characterization of nanostructured strontium hexaferrite thin films by the sol–gel method

Nanostructured single phase strontium hexaferrite, SrFe₁₂O₁₉, thin films have been synthesized on the (100) silicon substrate using a spin coating sol–gel process. The thin films with various Fe/Sr molar ratios of 8–12 were calcined at different temperatures from 500 to 900 °C. The composition, microstructure and magnetic properties of the SrFe₁₂O₁₉ thin films were characterized using Fourier transform infrared spectroscopy, differential thermal analysis, thermogravimetry, X-ray diffraction, electron microscopy and vibrating sample magnetometer. The results showed that the optimum molar ratio for Fe/Sr was 10 at which the lowest calcination temperature to obtain the single phase strontium hexaferrite thin film was 800 °C. The magnetic measurements revealed that the sample with Fe/Sr molar ratio of 10, exhibited higher saturation magnetization (267.5 emu/cm³) and coercivity (4290 Oe) in comparison with those synthesized under other Fe/Sr molar ratios.     

Piezoelectric, dielectric and magnetic properties of (1-x)Pb[Zr, Ti, (Mg1/2W1/2), (Ni1/3Nb2/3)]O3+x(Ni, Co, Cu)FeO4 composites

The phase structure, microstructure, piezoelectric properties, dielectric characteristic and the ME effect of magnetoelectric Pb[Zr_0.23Ti_0.36+0.02(Mg_1/2W_1/2)+0.39(Ni_1/3Nb_2/3)]O₃ (PZT)+xNi_0.8Co_0.1Cu_0.1Fe₂O₄ (NCCF) composite ceramics were prepared by the conventional solid state reaction method. The structural analysis of both the constituent phases and their composites was carried out by X-ray diffraction, energy dispersive spectrometry and scanning electron microscopy. The results showed cubic spinel structure for ferrite phase and tetragonal perovskite structure for ferroelectric phase. The piezoelectric constant, dielectric constant, Curie temperature, remanent polarization and coercive electric field decreased with increase of ferrite content. The coercive field strength, saturation magnetization and remanent magnetization increased with increasing ferrite content.     

Physical, electrical and dielectric properties of Ca-substituted strontium hexaferrite (SrFe12O19) nanoparticles synthesized by co-precipitation method

Calcium substituted strontium hexaferrite Ca_xSr_1−xFe₁₂O₁₉ (x=0.0−0.6) nanoparticles are synthesized by chemical co-precipitation method. The synthesized samples are characterized by Fourier Transform Infrared (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopy, Transmission Electron Microscopy, DC electrical resistivity and dielectric measurements. FTIR data of uncalcined sample shows that nitrate ions are present which disappeared on calcination at 920 °C. The XRD data shows that a single hexagonal magnetoplumbite phase is formed in samples in which the calcium content, x, is ≤0.20. However, a nonmagnetic phase (α-Fe₂O₃) in addition to the hexagonal phase is also present in samples with x>0.20. The average crystallite size is found between 17 and 29 nm. The DC electrical resistivity increases with increase of calcium content up to level of x=0.2 but decreased on further addition of calcium. The enhanced resistivity of the calcium doped material has potential applications in microwave devices. The variations of dielectric constant and dielectric loss angle are explained on the basis of Maxwell-Wagner and Koops models.     

Structural and magnetic properties of SrFe12O19 hexaferrite synthesized by a modified chemical co-precipitation method

M-type strontium hexaferrite (SrFe₁₂O₁₉) particles had been prepared by a modified chemical co-precipitation route. Structural and magnetic properties were systematically investigated. Rietveld refinement of X-ray powder diffraction results showed that the sample was single-phase with the space group of P6₃/mmc and cell parameter values of a=5.8751 Å and c=23.0395 Å. The results of field-emission scanning electronic microscopy showed that the grains were regular hexagonal platelets with sizes from 2 to 4 μm. The composition determined by energy dispersive spectroscopy is the stoichiometry of SrFe₁₂O₁₉. The ferrimagnetic to paramagnetic transition was sharp with Curie temperature T_C=737 K, which further confirmed that the samples were single phase. However, it was found that the coercivity, saturation magnetization and the squareness ratio of the synthesized SrFe₁₂O₁₉ samples were lower than the theoretical values, which could be explained by the multi-domain structure and the increase of the demagnetizing factor.     

Simple recipe to synthesize single-domain BaFe12O19 with high saturation magnetization

We report a new synthesis route for preparation of single-domain barium hexaferrite (BaFe₁₂O₁₉) particles with high saturation magnetization. Nitric acid, known as a good oxidizer, is used as a mixing medium during the synthesis. It is shown that formation of BaFe₁₂O₁₉ phase starts at 800 °C, which is considerably lower than the typical ceramic process and develops with increasing temperature. Both magnetization measurements and scanning electron microscope micrographs reveal that the particles are single domain up to 1000 °C at which the highest coercive field of 3.6 kOe was obtained. The best saturation magnetization of ≈60 emu/g at 1.5 T was achieved by sintering for 2 h at 1200 °C. Annealing at temperatures higher than 1000 °C increased the saturation magnetization, on the other hand, decreased the coercive field which was due to the formation of multi-domain particles with larger grain sizes. It is shown that the best sintering to obtain fine particles of BaFe₁₂O₁₉ occurs at temperatures 900-1000 °C. Finally, magnetic interactions between the hard BaFe₁₂O₁₉ phase and impurity phases were investigated using the Stoner-Wohlfarth model.     

Preparation of substituted barium ferrite BaFe12−x(Ti0.5Co0.5)xO19 by citrate precursor method and compositional dependence of their magnetic properties

As a possible candidate for the left-handed metamaterial with negative permeability, a series of Ti, Co-substituted M-type barium hexaferrite BaFe_12−x(Ti_0.5Co_0.5)_xO₁₉ (x=0, 1, 2, 3, 4 and 5) was prepared by citrate precursor method. The formation processes of the substituted barium hexaferrite compounds from the precursors were followed by the measurements of powder X-ray diffraction (XRD), Infrared absorption spectra (FT-IR), and thermogravimetry and differential thermal analysis (TG/DTA) coupled with mass spectroscopy (MS). In the case of the non-substituted sample, the formation of the barium hexaferrite is regulated by the thermal decomposition of BaCO₃ and the solid-state reactions of BaO and Fe₂O₃ in the temperature range from 800 to 1100 K. The formation temperature of the substituted BaFe_12−x(Ti_0.5Co_0.5)_xO₁₉ is higher than that for the non-substituted sample and increases with the value of x, due to the effects of carbonate ions incorporated by the partial substitution of Fe³⁺ by (Ti_0.5Co_0.5)³⁺. On heating up to ca. 1200 K, all the substituted samples transform into the magenetoplumbite phase as is the non-substituted sample. The compositional dependence of the magnetic properties of the substituted barium hexaferrite was investigated by the magnetization measurement. The decrease in the magnetic anisotropy was confirmed by the change in the magnetization curve and coercivity H_C with the composition x. A negative permeability spectrum was observed in the BaFe₉(Ti_0.5Co_0.5)₃O₁₉ in the frequency range from 2 to 4 GHz.     

Structural and electrical behavior of Pb(Mg1/4Cd1/4Mo1/2)O3 ceramics

Preliminary X-ray structural analysis of polycrystalline Pb(Mg_1/4Cd_1/4Mo_1/2)O₃ ceramics, prepared by a solid-state reaction technique, provides single-phase orthorhombic structure at room temperature. Detailed dielectric studies of the material as a function of temperature reveal a sharp phase transition at temperature T_c=49°C obeying Curie-Weiss behavior. Scanning electron microscope (SEM) studies of the sample show the uniform distribution of grains in the samples. A dielectric anomaly and ferroelectric phase transition observed at 49°C was supported by polarization studies. The activation energy of the sample was calculated from the dielectric data. The variation of dc resistivity with temperature suggests that the compound behaves as a negative temperature coefficient resistor (NTCR).     

Effect of Fe3+-doped Ca12Al14O33 cement on optical and thermal properties

This study aims to investigate the effect Fe ions doped into Ca₁₂Al₁₄O₃₃ (C12A7, 12CaO-7Al₂O₃) cement compound on its thermal and optical properties. Polycrystalline samples of Ca₁₂Al_14?xFe_xO₃₃ (where x?=?0.0, 0.5, and 1.0) were prepared via a solid state reaction in an oxygen atmosphere. The lattice constant of Ca₁₂Al₁₄O₃₃ determined using an XRD technique was in excellent agreement with first-principles calculations. With increasing Fe concentrations, the lattice constants were found to have increased. Additionally, the optical gaps of Ca₁₂Al_14?xFe_xO₃₃, (x?=?0, 0.25, 0.5, and 1.0) were 3.9?eV, 3.77?eV, 3.75?eV and 3.63?eV, respectively. It was clearly seen that the optical gap decreased with increasing Fe concentrations. As revealing by first-principles calculations, the optical gap was directly related to the electronic transition from the occupied electronic state of extra-framework O^2? ions (as free O^2? ions inside nano-cage) to the conduction band. Moreover, we also found that the thermal conductivity Ca₁₂Al_14?xFe_xO₃₃ was reduced when the larger atomic mass and atomic radii Fe was substituted into Al sites. Hence, this indicated that Fe³⁺-substitution into Al³⁺ sites of Ca₁₂Al₁₄O₃₃ cement directly affected both its optical gap and thermal conductivity.     

Electrical and magnetic properties of ε-Fe3N nanoparticles synthesized by chemical vapor condensation process

ε-Fe₃N nanoparticles synthesized by chemical vapor condensation (CVC) are covered with shells of disordered Fe₃O₄ phase, as observed by a transmission electron microscopy. The zero-field cooling and field cooling temperature dependence of magnetization, ac susceptibility as a function of frequency, magnetic hysteresis loops, and the temperature dependence of resistivity of the ε-Fe₃N nanoparticles are systematically studied. The results indicate the existence of complex magnetic properties, such as superparamagnetic behavior, exchange bias, magnetic dipole interaction, and the possible coexistence of ferromagnetic and spin-glass-like states and/or disordered surface spins of the shells at low temperatures. The temperature dependence of resistivity ρ(T) for compacted ε-Fe₃N nanoparticles in a temperature range of 110 K< T< 300 K can be well described by the mechanism of fluctuation-induced tunneling conduction, while that below 110 K can be ascribed to conducting electrons scattered by localized magnetic moments and impurity as well as the influence of freezing of spin-glass-like moments and/or disordered surface spins of the shells.     

Dielectric and magnetic permittivities of three new ceramic tungstates MPr2W2O10 (M = Cd,Co, Mn)

Broadband dielectric spectroscopy measurements revealed an anomalously large relative permittivity value (ε _r?=?884) for MnPr₂W₂O₁₀, a smaller value (ε _r?=?156) for CoPr₂W₂O₁₀ and the smallest value (ε _r?=?22) for CdPr₂W₂O₁₀ at low frequency (ν?=?0.1?Hz) and above room temperature in the insulating and paramagnetic state. Below 273?K, the relative permittivity (ε _r?～?24) did not depend significantly on frequency for all the tungstates under study. Electrical resistivity, thermoelectric power, electron paramagnetic resonance, magnetic susceptibility and magnetization provided experimental evidence that the studies tungstates were paramagnetic insulators with low n-type conduction. Only in the case of MnPr₂W₂O₁₀ was a ferrimagnetic order below 45?K observed. These effects are discussed within the framework of Maxwell–Wagner polarization, chemical covalent bonds and porosity mechanism.     

Improved multiferroic properties and a novel magnetic behavior of Bi0.8La0.2Fe1−xCoxO3 nanoparticles

Bi_0.8La_0.2Fe_1−xCo_xO₃ nanoparticles of single phase (BLFCO_x, x=0, 0.005, 0.01, 0.02) were prepared by a sol-gel method using polyvinyl alcohol as a surfactant. Co substitution at Fe site improved further dielectric properties of Bi_0.8La_0.2FeO₃ nanoparticles in the frequency range below 25 MHz at room temperature. Magnetization at 10 kOe, coercivities, and remanence of BLFCO_x nanoparticles increased with increasing Co content. It is interesting that the hysteresis loop of all the BLFCO_x nanoparticles presented a wasp-waisted shape. The property can open an important way to design new multiferroic applications of low hysteresis loss in low magnetic fields.     

Synthesis of coprecipitated strontium hexaferrite nanoparticles in the presence of polyvinyl alcohol

Strontium hexaferrite (SrFe₁₂O₁₉) nanoparticles were synthesized by the chemical coprecipitation method and using polyvinyl alcohol (PVA) as a protective agent. The synthesized samples were characterized by differential thermal analysis, X-ray diffraction, scanning and transmission electron microscopy, particle size analyzer, sedimentation test and vibrating sample magnetometer. In the presence of PVA, the single-phase SrFe₁₂O₁₉ nanoparticles were obtained at low temperature of 650 °C. The average particle size of SrFe₁₂O₁₉ precursor was 15 nm, which increased to 61 nm after calcination at 650 °C. The magnetic measurements indicated that PVA decreased coercivity from 4711 to 3216 Oe with particle size reduction. The results showed that PVA as a protective agent could be effective in decreasing the particle size, calcination temperature and coercivity of SrFe₁₂O₁₉ nanoparticles.     

Synthesis, characterization and magnetic properties on nanocrystalline BaFe12O19 ferrite

Single phase BaM (BaFe₁₂O₁₉) ferrites are prepared by using sol–gel method. The preparing conditions of samples are investigated in detail, such as acid/nitrate ratio, the value of pH and annealing temperature. The best conditions on preparing BaFe₁₂O₁₉, which can be obtained on a Fe/Ba ratio of 12, the citric acid contents R = 3, the starting pH of solution is 9, and annealing temperature 950 °C. The thermal decomposition behavior of the dried gel was examined by TG–DSC, the structure and properties of powders were measured respectively by XRD techniques. The magnetic properties of barium ferrites are emphatically researched about the changing crystallite size and annealing temperature by the vibrating sample magnetometer (VSM). Magnetic measurement shows that the barium ferrite samples annealed at 1000 °C has the maximal coercive field of 5691.91 Oe corresponding to the maximal remnant magnetization of 35.60 emu/g and the sample synthesized at 1000 °C has the maximal saturation magnetization of 60.75 emu/g.     

Magnetic and rheological properties of monodisperse Fe3O4 nanoparticle/organic hybrid

Fe₃O₄ nanoparticle/organic hybrids were synthesized via hydrolysis using iron (III) acetylacetonate at ∼80 °C. The synthesis of Fe₃O₄ was confirmed by X-ray diffraction, selected-area diffraction, and X-ray photoelectron spectroscopy. Fe₃O₄ nanoparticles in the organic matrix had diameters ranging from 7 to 13 nm depending on the conditions of hydrolysis. The saturation magnetization of the hybrid increased with an increase in the particle size. When the hybrid contained Fe₃O₄ particles with a size of less than 10 nm, it exhibited superparamagnetic behavior. The blocking temperature of the hybrid containing Fe₃O₄ particles with a size of 7.3 nm was 200 K, and it increased to 310 K as the particle size increased to 9.1 nm. A hybrid containing Fe₃O₄ particles of size greater than 10 nm was ferrimagnetic, and underwent Verwey transition at 130 K. Under a magnetic field, a suspension of the hybrid in silicone oil revealed the magnetorheological effect. The yield stress of the fluid was dependent on the saturation magnetization of Fe₃O₄ nanoparticles in the hybrid, the strength of the magnetic field, and the amount of the hybrid.     

Local spin reversal and associated magnetic responses in Ga-substituted Pb-hexaferrites

We have studied magnetic structure and properties of Ga-substituted Pb-hexaferrites having the stoichiometry of PbFe_12−xGa_xO₁₉ with x=6 (i.e., Fe:Ga=1:1). According to the neutron diffraction results, this compound is characterized by a collinear spin structure below its Curie temperature (∼325 K). Analysis of the neutron diffraction patterns further indicates that the magnetic-moment direction of Fe³⁺ ions located at the octahedral 2a sublattice is downward while that of the unsubstituted PbFe₁₂O₁₉ is upward at room temperature. With decreasing temperature, the Fe³⁺ magnetic moment at the octahedral 2a sublattice undergoes a reorientation to the upward direction while that of the unsubstituted PbFe₁₂O₁₉ remains upward down to 5 K. This selective local spin reversal at the 2a sublattice of PbFe₆Ga₆O₁₉ was attributed to the weakening of the superexchange interaction between the octahedral 2a site and the tetrahedral 4f_IV site upon the preferential substitution of Ga ions for Fe ions at these two neighboring sites. Comparison of the neutron diffraction results with dc magnetization responses and ac susceptibilities further indicates that the paramagnetic–ferrimagnetic transition at ∼325 K (T_c) is followed by the local spin reversal at lower temperatures.     

Microstructure-dependent giant dielectric response in CaCu3Ti4O12 ceramics

CaCu₃Ti₄O₁₂ ceramics were prepared at the sintering temperatures ranged from 1025 to 1125 °C, and the dielectric characteristics were evaluated together with the microstructures. The giant dielectric constant with the maximum of 53,120 was obtained in CaCu₃Ti₄O₁₂ ceramics at room temperature and 10 kHz, and strong processing and microstructure dependence of dielectric characteristics of the present ceramics was determined. The precipitation of the dispersed Cu-rich secondary phases of CuO and/or Cu₂O and their network structure provided the extrinsic origins of the enhanced giant dielectric response, and the present findings would offer the greater potential for enhancing the giant dielectric constant and controlling the dielectric loss in CaCu₃Ti₄O₁₂ ceramics by optimizing the microstructures.     

Structural and magnetic studies on mechanosynthesized BaFe12−xMnxO19

Barium hexaferrite powders with manganese substitution were prepared by mechanosynthesis. The structural and magnetic properties were characterized by X-ray diffractometer and vibration sample magnetometer, respectively. XRD patterns were refined by Rietveld method. Preferential site occupation of manganese ion was investigated by room temperature (RT) Mössbauer measurements. XRD results showed a single-phase barium hexaferrite with some residual hematite. Crystallite size was observed to decrease with substitution amount. Lower saturation magnetization and increased coercivity is observed in substituted samples. RT Mössbauer measurements showed that manganese ions preferentially occupy 12k, 4f₂, and 2a sites.