Magnetic properties of prussian blue modified Fe3O4 nanocubes

Size controlled cubic Fe₃O₄ nanoparticles in the size range 90–10 nm were synthesized by varying the ferric ion concentration using the oxidation method. A bimodal size distribution was found without ferric ion concentration and the monodispersity increased with higher concentration. The saturation magnetization decreased from 90 to 62 emu/g when the particle size is reduced to 10 nm. The Fe₃O₄ nanoparticles with average particle sizes 10 and 90 nm were surface modified with prussian blue. The attachment of prussian blue with Fe₃O₄ was found to depend on the concentration of HCl and the particle size. The saturation magnetization of prussian blue modified Fe₃O₄ varied from 10 to 80 emu/g depending on the particle size. The increased tendency for the attachment of prussian blue with smaller particle size was explained based on the surface charge. The prussian blue modified magnetite nanoparticles could be used as a radiotoxin remover in detoxification applications.     

Synthesis and magnetic properties of Au-coated amorphous Fe20Ni80 nanoparticles

Gold-coated nanoparticles of Fe₂₀Ni₈₀ (permalloy) have been synthesized by a microemulsion process. The as-prepared samples consist of ∼5 nm diameter particles of amorphous Fe₂₀Ni₈₀ that are likely encapsulated in B₂O₃. One or more Fe₂₀Ni₈₀@B₂O₃ particles are subsequently encapsulated in 8-20 nm gold nanospheres, as determined by TEM and X-ray powder diffraction (XRD) line broadening. The gold shells were found to be under expansive strain. Magnetic data confirm the existence of a superparamagnetic phase with a blocking temperature, T_B, of ∼33 K. The saturation magnetization, M_S, of the as-prepared, Au-coated sample is ∼65 emu g⁻¹ at 5 K and ∼16 emu g⁻¹ at 300 K. The coercivity, H_C, is ∼280 Oe at 5 K.     

Green synthesis and characterization of superparamagnetic Fe3O4 nanoparticles

In this paper, we have first demonstrated a facile and green synthetic approach for preparing superparamagnetic Fe₃O₄ nanoparticles using α-d-glucose as the reducing agent and gluconic acid (the oxidative product of glucose) as stabilizer and dispersant. The X-ray powder diffraction (XRD), X-ray photoelectron spectrometry (XPS), and selected area electron diffraction (SAED) results showed that the inverse spinel structure pure phase polycrystalline Fe₃O₄ was obtained. The scanning electron microscopy (SEM) and transmission electron microscopy (TEM) results exhibited that Fe₃O₄ nanoparticles were roughly spherical shape and its average size was about 12.5 nm. The high-resolution TEM (HRTEM) result proved that the nanoparticles were structurally uniform with a lattice fringe spacing about 0.25 nm, which corresponded well with the values of 0.253 nm of the (3 1 1) lattice plane of the inverse spinel Fe₃O₄ obtained from the JCPDS database. The superconducting quantum interference device (SQUID) results revealed that the blocking temperature (T_b) was 190 K, and that the magnetic hysteresis loop at 300 K showed a saturation magnetization of 60.5 emu/g, and the absence of coercivity and remanence indicated that the as-synthesized Fe₃O₄ nanoparticles had superparamagnetic properties. Fourier transform infrared spectroscopy (FT-IR) spectrum displayed that the characteristic band of Fe-O at 569 cm⁻¹ was indicative of Fe₃O₄. This method might provide a new, mild, green, and economical concept for the synthesis of other nanomaterials.     

Green synthesis of soya bean sprouts-mediated superparamagnetic Fe3O4 nanoparticles

Superparamagnetic Fe₃O₄ nanoparticles were first synthesized via soya bean sprouts (SBS) templates under ambient temperature and normal atmosphere. The reaction process was simple, eco-friendly, and convenient to handle. The morphology and crystalline phase of the nanoparticles were determined from scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and X-ray diffraction (XRD) spectra. The effect of SBS template on the formation of Fe₃O₄ nanoparticles was investigated using X-ray photoemission spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FT-IR). The results indicate that spherical Fe₃O₄ nanoparticles with an average diameter of 8 nm simultaneously formed on the epidermal surface and the interior stem wall of SBS. The SBS are responsible for size and morphology control during the whole formation of Fe₃O₄ nanoparticles. In addition, the superconducting quantum interference device (SQUID) results indicate the products are superparamagnetic at room temperature, with blocking temperature (T_B) of 150 K and saturation magnetization of 37.1 emu/g.     

In situ synthesis and characterization of LiNi0.5La0.08Fe1.92O4-polyaniline core-shell nanocomposites

Core-shell-structured LiNi_0.5La_0.08Fe_1.92O₄-polyaniline (PANI) nanocomposites with magnetic behavior were synthesized by in situ polymerization of aniline in the presence of LiNi_0.5La_0.08Fe_1.92O₄ nanoparticles. The structure, morphology and magnetic properties of samples were characterized by powder X-ray diffraction (XRD), Fourier transform infrared (FTIR), UV-vis absorption, transmission electron microscopy (TEM) and vibrating sample magnetometer (VSM) technique. The results of spectroanalysis indicated that there was interaction between PANI chains and ferrite particles. TEM study showed that LiNi_0.5La_0.08Fe_1.92O₄-PANI nanocomposites presented a core-shell structure with a magnetic core of 30-50 nm diameter and an amorphous shell of 10-20 nm thickness. The nanocomposites under applied magnetic field exhibited the hysteresis loops of the ferromagnetic nature. The saturation magnetization and coercivity of nanocomposites decreased with decreasing content of LiNi_0.5La_0.08Fe_1.92O₄. The polymerization mechanism and bonding interaction in the nanocomposites have been discussed.     

Monodispersed nanocrystalline Co1–xZnxFe2O4 particles by forced hydrolysis: Synthesis and characterization

Zinc-substituted cobalt ferrites, Co_1–xZn_xFe₂O₄, were for the first time successfully prepared by forced hydrolysis method. The obtained materials are single phase, monodispersed nanocrystalline with an average grain size of about 3 nm. These materials are superparamagnetic at room temperature and ferrimagnetic at temperature lower than the blocking temperature. When the zinc substitution increases from x=0 to 0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g. The high saturation magnetization of these samples suggests that this method is suitable for preparing high-quality nanocrystalline magnetic ferrites for practical applications.     

Effect of ferrofluid concentration on electrical and magnetic properties of the Fe3O4/PANI nanocomposites

Magnetic nanocomposites can be controlled and tailored to provide the desired mechanical, physical, chemical, and biomedical properties depending on the final applications. The coating of ferrite nanoparticles with polymers affords the possibility of minimizing agglomeration in large-scale commercial synthesis of nanocomposite materials. The process of coating not only provides effective encapsulation of individual nanoparticles, but also controls the growth in size, thus, yielding a better overall size distribution. In this paper, in-situ polymerization of aniline was carried out in different concentration of the ferrofluid with the aim to obtain agglomerate free nanocomposites. The role of the ferrite concentration was investigated by the spectral, morphological, conductivity, and magnetic properties of Fe₃O₄/polyaniline (PANI) nanocomposites. XRD revealed the presence of spinel phase of Fe₃O₄ and the particle size was calculated to be 14.3 nm. Spectral analysis confirmed the formation of PANI encapsulated Fe₃O₄ nanocomposite. Conductivity of the nanocomposites was found to be in the range of 0.001–0.003 S/cm. Higher saturation magnetization of 3.2 emu/g was observed at 300 K, revealing a super paramagnetic behavior of this nanocomposite.     

Synthesis of Co-Cu-Zn doped Fe3O4 nanoparticles with tunable morphology and magnetic properties

Co-Cu-Zn doped Fe₃O₄ nanoparticles can be successfully synthesized using a simple method. The particles in the size range 20−400 nm with different regular shapes i.e. sphere-like, regular hexane and tetrahedron are controllably achieved by changing the metal ion concentration. Compared to pure Fe₃O₄ without dopants, Co-Cu-Zn doped Fe₃O₄ nanoparticles exhibit better microwave absorbing properties at 2−18 GHz. Among three Co-Cu-Zn doped Fe₃O₄ nanoparticles with different morphologies, tetrahedral Co-Cu-Zn doped Fe₃O₄ nanoparticles represent a better dielectric loss in high frequency range. This work is believed the first known report of Co-Cu-Zn doped Fe₃O₄ nanoparticles with tunable morphology and magnetic properties through the hydrothermal process without using any organic solvents, organic metal salts or surfactants.     

Synthesis and magnetic characterization of Zn0.6Ni0.4Fe2O4 nanoparticles via a polyethylene glycol-assisted hydrothermal route

Zn-doped nickel ferrite nanoparticles (Zn_0.6Ni_0.4Fe₂O₄) have been prepared via a surfactant, polyethylene glycol assisted hydrothermal route. X-ray powder diffractometry (XRD), Fourier transform infrared spectroscopy, transmission electron microscopy (TEM), and vibrating scanning magnetometry (VSM) were used for the structural, morphological, and magnetic characterizations of the product, respectively. TEM analysis revealed that the nanoparticles have a narrow size distribution, with average particle size of 15±1 nm, which agrees well with the XRD based estimate of 14±2 nm. The absence of saturation and remanent magnetization, and coercivity in the high temperature region of the M-H curve and non-zero magnetic moments indicate superparamagnetism of the nanoparticles with a canted spin structure. The appearance of a peak on the temperature-dependent zero-field cooling magnetization curve at ∼190 K indicates the blocking temperature of the sample.     

Magnetic properties of nanocrystalline Co1−xZnxFe2O4 prepared by forced hydrolysis method

Nanocrystalline zinc-substituted cobalt ferrite powders, Co_1−xZn_xFe₂O₄ (x=0, 0.2, 0.4), were for the first time prepared by forced hydrolysis method. Magnetic and structural properties in these specimens were investigated. The average crystallite size is about 3.0 nm. When the zinc substitution increases from x=0 to x=0.4, at 4.2 K, the saturation magnetization increases from 72.1 to 99.7 emu/g and the coercive field decreases from 1.22 to 0.71 T. All samples are superparamagnetic at room temperature and ferrimagnetic at temperatures below the blocking temperature. The high value of the saturation magnetization and the very thin thickness of the disorder surface layer of all samples suggests that this forced hydrolysis method is suitable not only for preparing two metal element systems but also for three or more ones.     

Microwave anneal effect on magnetic properties of Ni0.6Zn0.4Fe2O4 nano-particles prepared by conventional hydrothermal method

Ni_0.6Zn_0.4Fe₂O₄ ferrite nano-particles with a crystallite size of about 20 nm were prepared by the conventional hydrothermal method, followed by annealing in a microwave oven for 7.5-15 min. The microstructure and magnetic properties of the samples were characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy and vibrating sample magnetometry. The microwave annealing process has slight effect on the morphology and size of Ni_0.6Zn_0.4Fe₂O₄ ferrite nano-particles. However it reduces the lattice parameter and enhances the densification of the particles, and then greatly increases the saturation magnetization (50-56 emu/g) and coercive force of the samples as compared to the non-annealing condition. The microwave annealing process is an effective way to rapidly synthesize high performance ferrite nano-particle.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Heat dissipation and magnetic properties of surface-coated Fe3O4 nanoparticles for biomedical applications

In this study, the influence of surface coating on the magnetic and heat dissipation properties of Fe₃O₄ nanoparticles was investigated. Fe₃O₄ nanoparticles that ranged in size between (particle sizes of 20 and 30 nm) were coated with polyethylenimine (PEI), oleic acid, and Pluronic F-127. Surface coatings that were composed of thick layers of oleic acid and Pluronic F-127 reduced dipole interactions between the particles, and resulted in reduced coercivity and decreased Néel relaxation times. The ac magnetization measurements revealed that the heat dissipation of the PEI-coated Fe₃O₄ nanoparticles was induced by hysteresis loss and Brownian relaxation loss and that of the oleic-acid-coated Fe₃O₄ nanoparticles was mainly induced by hysteresis loss and Néel relaxation loss.     

The colloidal stability and core-shell structure of magnetite nanoparticles coated with alginate

The adsorption of alginate (Alg) onto the surface of in water dispersed Fe₃O₄ nanoparticles and zeta potential of alginate-coated Fe₃O₄ nanoparticles have been investigated to optimize the colloidal stability of Alg-coated Fe₃O₄ nanoparticles. The adsorption amount of Alg increased with the decrease of adsorption pH. The zeta potential of Fe₃O₄ nanoparticles shifted to a lower value after adsorption of Alg. The lower adsorption pH was the lower zeta potential of Fe₃O₄ nanoparticles became. The Alg-coated Fe₃O₄ nanoparticles were found to be stabilized by steric and electrostatic repulsions. Those prepared at pH 6 were not stable around pH 5, and those prepared at pH 4 became unstable at pH below 3.5. Alg of M_w 45 kDa was a little bit more adsorbed onto nanoparticles surface than that of M_w 24 kDa. An average Fe₃O₄ core size of 9.3 ± 1.7 nm was found by transmission electronic microscopy. An average hydrodynamic diameter of 30-150 nm was measured by photon correlation spectroscopy. However, an average core size of 10 nm and an average hydrodynamic diameter of 38 nm were estimated from the magnetization curve of the concentrated magnetic fluids (MFs). The maximum available saturation magnetization of MFs was about 3.5 kA/m.     

Synthesis and magnetic characterization of Zn0.7Ni0.3Fe2O4 nanoparticles via microwave-assisted combustion route

We report on the synthesis of Zn_0.7Ni_0.3Fe₂O₄ nanoparticles via microwave assisted combustion route by using urea as fuel. XRD and FT-IR analyses confirm the composition and structure as spinel ferrite. The crystallite size estimated from XRD (16.4 nm) and the magnetic core size (15.04 nm) estimated from VSM agree well, while a slightly smaller magnetic diameter reflects a very thin magnetically dead layer on the surface of the nanoparticles. Morphological investigation of the products was done by TEM which revealed the existence of irregular shapes such spherical, spherodial and polygon. Magnetization measurements performed on Zn_0.7Ni_0.3Fe₂O₄ nanoparticles showed that saturation was not attained at even in the high magnetic field. The sample shows superparamagnetic behavior at around the room temperature and ferromagnetic behavior below the blocking temperature which is measured as 284 K.     

Preparation and magnetic properties of magnetite nanoparticles by sol–gel method

 Magnetite (Fe₃O₄) nanoparticles have been successfully synthesized by sol–gel method combined with annealing under vacuum. The phase structures, morphologies, particle sizes, chemical composition, and magnetic properties of Fe₃O₄ nanoparticles have been characterized by X-ray diffraction, field emission scanning electron microscopy, energy-dispersive X-ray spectrometer and vibrating sample magnetometer (VSM). The results indicate that the size, the corresponding saturation magnetization value and coercivity value of Fe₃O₄ nanoparticles increase with the increase of synthesized temperature. And the phase transformation of Fe₃O₄ nanoparticles has been studied under different atmospheres and temperatures.     

Comparative study of structural and magnetic properties of nano-crystalline Li0.5Fe2.5O4 prepared by various methods

Lithium ferrite has been considered as one of the highly strategic magnetic material. Nano-crystalline Li_0.5Fe_2.5O₄ was prepared by four different techniques and characterized by X-ray diffraction, vibrating sample magnetometer (VSM), transmission electron microscope (TEM) and Fourier transform infrareds (FTIR). The effect of annealing temperature (700, 900 and 1050 °C) on microstructure has been correlated to the magnetic properties. From X-ray diffraction patterns, it is confirmed that the pure phase of lithium ferrite began to form at 900 °C annealing. The particle size of as-prepared lithium ferrite was observed around 40, 31, 22 and 93 nm prepared by flash combustion, sol-gel, citrate precursor and standard ceramic technique, respectively. Lithium ferrite prepared by citrate precursor method shows a maximum saturation magnetization 67.6 emu/g at 5 KOe.     

Microwave synthesis of magnetic Fe3O4 nanoparticles used as a precursor of nanocomposites and ferrofluids

Methods to synthesize magnetic Fe₃O₄ nanoparticles and to modify the surface of particles are presented in the present investigation. Fe₃O₄ magnetic nanoparticles were prepared by the co-precipitation of Fe³⁺ and Fe²⁺, NH₃·H₂O was used as the precipitating agent to adjust the pH value, and the aging of Fe₃O₄ magnetic nanoparticles was accelerated by microwave (MW) irradiation. The obtained Fe₃O₄ magnetic nanoparticles were characterized by Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), X-ray powder diffraction (XRD) and vibrating sample magnetometer (VSM). The average size of Fe₃O₄ crystallites was found to be around 8–9 nm. Thereafter, the surface of Fe₃O₄ magnetic nanoparticles was modified by stearic acid. The resultant sample was characterized by FT-IR, scanning electron microscopy (SEM), XRD, lipophilic degree (LD) and sedimentation test. The FT-IR results indicated that a covalent bond was formed by chemical reaction between the hydroxyl groups on the surface of Fe₃O₄ nanoparticles and carboxyl groups of stearic acid, which changed the polarity of Fe₃O₄ nanoparticles. The dispersion of Fe₃O₄ in organic solvent was greatly improved. Effects of reaction time, reaction temperature and concentration of stearic acid on particle surface modification were investigated. In addition, Fe₃O₄/polystyrene (PS) nanocomposite was synthesized by adding surface modified Fe₃O₄ magnetic nanoparticles into styrene monomer, followed by the radical polymerization. The obtained nanocomposite was tested by thermogravimetry (TG), differential scanning calorimetry (DSC) and XRD. Results revealed that the thermal stability of PS was not significantly changed after adding Fe₃O₄ nanoparticles. The Fe₃O₄ magnetic fluid was characterized using UV–vis spectrophotometer, Gouy magnetic balance and laser particle-size analyzer. The testing results showed that the magnetic fluid had excellent stability, and had susceptibility of 4.46×10⁻⁸ and saturated magnetization of 6.56 emu/g. In addition, the mean size d (0.99) of magnetic Fe₃O₄ nanoparticles in the fluid was 36.19 nm.     

Magnetic properties of nanosized γ-Fe2O3 and α-(Fe2/3Cr1/3)2O3, prepared by thermal decomposition of heterometallic single-molecular precursor

Thermal decomposition of the trinuclear complex [Fe₂CrO(CH₃COO)₆(H₂O)₃]NO₃ at 300, 400 and 500 °C gave γ-Fe₂O₃ nanoparticles along with amorphous chromium oxide, while decomposition of the same starting compound at 600 and 700 °C led to the formation of α-(Fe_2/3Cr_1/3)₂O₃ nanoparticles. Size of γ-Fe₂O₃ nanoparticles, determined by X-ray diffraction, was in the range from 9 to 11 nm and increased with formation temperature growth. Average size of α-(Fe_2/3Cr_1/3)₂O₃ nanoparticles was about 40 nm and almost did not depend on the temperature of its formation. γ-Fe₂O₃ nanoparticles possessed superparamagnetic behavior with blocking temperature 180-250 K, saturation magnetization 29-35 emu/g at 5 K, 44-49 emu/g at 300 K and coercivity 400-600 Oe at 5 K. α-(Fe_2/3Cr_1/3)₂O₃ nanoparticles were characterized by low magnetization values (2.7 emu/g at 70 kOe). Such magnetic properties can be caused by non-compensated spins and defects present on the surface of these nanoparticles. The increase of α-(Fe_2/3Cr_1/3)₂O₃ formation temperature led to decrease of magnetization (being compared for the same fields), which may be caused by decrease of the quantity of defects or non-compensated spins (due to decrease of particles' surface).     

Ni80Fe20 permalloy nanoparticles: Wet chemical preparation, size control and their dynamic permeability characteristics when composited with Fe micron particles

Ni₈₀Fe₂₀ permalloy nanoparticles (NPs) have been prepared by the polyol processing at 180 °C for 2 h and their particle sizes can be precisely controlled in the size range of 20-440 nm by proper addition of K₂PtCl₄ agent. X-ray diffraction results show that the Ni-Fe NPs are of FCC structure, and a homogeneous composition and a narrow size distribution of these NPs have been confirmed by scanning electron microscopy assisted with energy dispersion spectroscopy of X-ray (SEM-EDX). The saturation magnetization of ~440nm NPs is 80.8 emu/g that is comparable to that of bulk Ni₈₀Fe₂₀ alloys, but it decreases to 28.7 emu/g for ~20 nm NPs. The coercive force decreases from 90 to 3 Oe with decreasing NP size. The wide range of particle size is exploited to seek for high permeability composite particles. The planar type samples composed of the NiFe NPs exhibit low initial permeability due to the deteriorated magnetic softness and low packing density. However, when they are mixed with Fe micron particles, the initial permeability significantly increases depending on the mixing ratio and the NiFe NP size. A maximum initial permeability is achieved to be ~9.1 at 1 GHz for the Fe-10 vol%NiFe (~20 nmΦ), which is about three times that of pure Fe micron particles. The effects of Ni-Fe particle size, volume percentage and solvent on the static and dynamic permeability are discussed.