基于半导体光放大器的一阶IIR微波光子学滤波器及其品质因素分析

对基于半导体光放大器(SOA)环形腔结构的一阶无限冲击响应(IIR)微波光子学滤波器的品质因数(Q值)进行了实验和理论研究. 通过在有源环内置入窄带光滤波器,并调节有源环的输入光功率、SOA抽运电流、实验得到的最高Q值接近200. 理论分析表明为了得到较高的Q值,应尽可能提高信噪比和信号光的环路增益. 在考虑了 SOA中放大的自发辐射(ASE)噪声的基础上,计算了输入光功率、SOA抽运电流、环内光滤波器的带宽对Q值的影响. 数值计算的结果与实验现象基 关键词： 微波光子学滤波器 Q值')" href="#">Q值 半导体光放大器 放大的自发辐射     

基于半导体光放大器的光控器件中控制光的性能分析

在O-RPR(optical resitient packet ring)光弹性分组环的基础上分析了在双环耦合全光缓存器这一基于半导体光放大器(SOA)的光控器件中要顺利实现数据的读写控制对光控制层功率提出的要求及其影响因素，讨论了由于信号光脉冲形状不是理想方波而造成的啁啾及脉冲压缩现象，分析了控制光功率波动及其信噪比对输出数据造成的影响. 得到的结论对其他基于SOA的光控器件同样具有借鉴意义. 关键词： O-RPR光弹性分组环 基于SOA的光控器件 双环耦合全光缓存器 控制层光功率     

半导体光放大器中光波传输特性研究

根据半导体光放大器(SOA)载流子速率方程和光波在SOA内的传输方程,采用分段的方法计算出光波功率和相位与载流子浓度的关系公式。在泵浦光输入功率分别为5mW和15mW情况下通过仿真得到泵浦光输出波形和归一化转换光波形,其中归一化转换光的波形变化可间接体现不同泵浦光输入功率对SOA内载流子浓度的影响。分析了泵浦光波长和SOA注入电流对探测光的归一化输出、相位和频率啁啾产生的影响。结果表明,随着泵浦光波长的增加,探测光的三种光波特性曲线逐渐趋于平缓。注入电流将会直接影响到SOA的载流子浓度,以此对探测光的输出产生影响,注入电流越大,探测光的频率漂移越远。     

基于半导体光放大器的相位调制信号再生器

对相位调制光通信系统进行幅度和相位的同时再生十分必要。采用半导体光放大器(SOA)作为非线性媒介,搭建一个非线性的马赫曾德尔干涉仪作为再生器,利用SOA的增益特性,在锁相本地振荡抽运源的驱动下,实现对相位调制信号的幅度和相位的同时再生。理论推导了入射光信号经过基于SOA的再生器后的光场分布公式;讨论了不同入射信号光功率下,抽运光与信号光的相位差对信号功率增益的影响,给出了入射光的最优参数;数值仿真了带有噪声的相位调制信号再生前后的相位分布、强度分布和误码率。研究结果表明,基于SOA的光再生器有良好的再生效果。     

基于半导体光放大器的干涉型器件中噪声特性的分析

分析了基于半导体光放大器(SOA)的干涉仪分别处于“开”、“关”两种工作状态时的输出信噪比及噪声指数,发现当干涉仪处于“开”态时输出信噪比有所恶化,并导出了附加噪声因子的表达式。实验结果进一步证明了理论分析的正确性。     

基于半导体光放大器和光学滤波器的同相波长转换理论研究

采用半导体光放大器(SOA)级联滤波器的方案可以实现高速全光波长转换,其中,滤波器实质上是对SOA输出信号的光谱进行优化操作.文中利用带通滤波器(BPF)和延时干涉仪(DI)组成的光谱优化器,不仅实现了80Gbit/s同相波长转换,而且基于遗传算法设计光谱优化器的参数,极大地提高了输出信号的质量.同时,也从理论上分析了SOA中超快带内效应对信号光谱的影响以及光谱优化器中BPF和DI的消光比对输出信号质量的影响.     

多电极半导体光放大器对增益特性的改善

提出了采用多电极实现电流非均匀注入来改变半导体光放大器(SOA)内部的载流子分布,从而改变其增益饱和特性的一种新的方案.用SOA分段模型的计算结果表明,与单电极均匀注入电流的SOA 相比,在同样的总注入电流下,对一个两电极SOA采用前面小后面大的非均匀电流注入,可以提高饱和输出功率和饱和输入功率.而采用前面大后面小的电流注入方式,则将使SOA更容易发生饱和,不仅饱和输出功率与饱和输入功率减小,而且增益谱在饱和后的压缩程度加大,增益谱压缩的对称性提高.对多电极SOA,可以方便灵活地调节各节之间的长度比和注入电流比来满足不同的应用要求.     

一种全光逻辑或非门的理论和实验研究

基于单端半导体光放大器(SOA)中的交叉增益调制(XGM)效应实现了全光逻辑或非运算功能,建立了该方案的理论模型,进行了数值模拟.实验中实现了10 Gb/s的全光逻辑或非运算功能,并对理论模拟和实验结果进行了讨论和分析,指出了输出消光比与连续光功率及注入电流之间的关系.理论分析结果与实验结果相符合.     

基于XGM波长变换系统中变换脉冲上升时间和脉冲宽度的研究

本文首先对半导体光放大器(SOA)中影响载流子寿命的因素进行了简单的理论分析,建立了SOA中动态载流子的模型,并且用这个模型分析了在2.5Gb/s非归零码(NRZ)条件下,基于交叉增益调制(XGM)波长变换系统中,泵浦光和信号光不同功率组合、不同波长组合,SOA的不同偏置电流等条件对变换脉冲的上升时间和脉冲的半高全宽的影响,并对结果进行了理论上的解释.     

全固态Nd:YAG激光器热效应及输出光束波前像差分析

高功率全固态激光器的诸多腔内扰动因素均会直接影响到激光输出功率和光束质量。首先采用传输矩阵方法简要讨论了在稳定腔情形下热透镜焦距与本征模式光斑尺寸的关系。进一步采用Hartmann-Shack波前传感器和模式法波前重构,对二极管抽运全固态声光调Q激光器输出倍频光束质量进行了分析,得到前35阶Zernike像差系数、波前峰谷值和均方根等畸变参量,计算还可得到点扩散函数分布和环围能量曲线等,从而全面了解输出光束质量和动态像差特性。分析表明输出倍频光的波前Zernike像差主要集中在前15阶,由于晶体热效应及腔内其它扰动因素的影响,较显著波前像差有离焦系数Z_3、低阶像散Z_4和Z_5,以及球差Z_(10)等。     

Modeling and optimizing the pulse replicator based on the active recirculating optical loop

Signal to noise ratio (SNR) is an important parameter in the output signal of the pulse replicator. We propose a novel new method to improve this parameter. Instead of focusing on lowering the noise level of the optical amplifier and limiting the accumulation of amplified spontaneous emission (ASE) noise in the loop, we consider the optimization of other system parameters. By modeling with a predefined implementation of the pulse replicator, an evaluation function of SNR is constructed, with variables such as the coupling ratio, the optical fiber length. In this paper, we will construct the quantitative function between SNR and the coupling ratio. According to the evaluation function, we can determine the optimal value of the coupling ratio for the coupler to obtain the best SNR within the predefined parameters. The experiment will prove that the SNR in the output signal of the pulse replicator has been increased while using the optimal coupling ratio. This will contribute greatly to future work on improving SNR of the pulse replicator.     

Analysis and experiments of self-injection magnetron

Magnetrons are widely used in microwave-based industrial applications, which are rapidly developing. However, the coupling between their output frequency and power as well as their wideband spectra restricts their further application. In this work, the output frequency and power of a magnetron are decoupled by self-injection. Moreover, the spectral bandwidth is narrowed, and the phase noise is reduced for most loop phase values. In order to predict the frequency variation with loop phase and injection ratio, a theoretical model based on a circuit equivalent to the magnetron is developed. Furthermore,the developed model also shows that the self-injection magnetron is stabler than the free-running magnetron and that the magnetron's phase noise can be reduced significantly for most loop phase values. Experimental results confirm the conclusions obtained using the proposed model.     

面向语音增强的约束序贯高斯混合模型噪声功率谱估计

提出了一种基于极大似然的噪声对数功率谱估计方法,采用高斯混合模型对每一个频带上的功率谱包络构建统计模型,将时序包络划分为语音和非语音类,它们分别对应于高斯混合模型的两个高斯分量,描述语音和非语音的统计分布,其中非语音高斯分量的均值即为噪声功率谱的最优估计.采用序贯学习的方法,在极大似然准则下逐帧更新模型参数,并逐帧给出噪声功率谱的最优估计值。此外,由于序贯更新过程中语音信号长时缺失,容易导致模型失稳,提出了一种在线的最小描述长度准则(MDL)来判断语音信号是否长时缺失,从而保证了模型的稳定性.实验表明,算法性能整体优于经典的MS和IMCRA算法。      

Barkhausen noise and domain structure dynamics in Si-Fe at different points of the magnetization curve

In the present relationship between Barkhausen noise and domain structure evolution along the hysteresis loop in 3% Si–Fe has been investigated. The noise power spectrum has been measured vs. induction during cyclic magnetization of the material at a very low constant rate. The obtained results show that the behavior of the noise power along the magnetization curve can be related to the character of the domain structure rearrangements taking place at different levels of induction. Such a connection is reflected in a relationship between the noise power and the shape of the hysteresis loop. The measured noise power spectra are interpreted through the use of a suitable model. This makes possible to connect the shape of the magnetization curve to the microscopic parameters characterizing the dynamic of the domain wall during a large Barkhausen jump.     

谐振式集成光学陀螺噪声分析与实验研究

针对目前谐振式集成光学陀螺(IORG)输出检测精度与其理论极限灵敏度存在两个数量级差别的情况,分析了IORG系统中存在的主要噪声源;搭建了基于单光路锁频和单光路输出的IORG噪声分离系统;分别对无光情况下信号检测系统中各部分的噪声以及陀螺静态频率锁定情况下各部分的噪声影响进行了测试与分析;得到了系统的噪声分布情况。实验结果表明:光路噪声以及包括探测器热噪声和散粒噪声的电路固有噪声为系统的主要噪声源。     

Phase Noise in Millimeter Wave Phase-Locked Loop with Mixer

In order to estimate the phase noise of millimetre wave (MMW) phase-locked oscillator (PLO), the phase noise relation of signals in MMW phase-locked loop (PLL) with frequency conversion is analyzed. The signals include output of MMW PLO, intermediate frequency (IF) output of harmonic mixer and output of microwave oscillator serving as local oscillator (LO). A method to estimate the phase noise of MMW PLO is presented, which is based on the phase noise of LO and IF. At the same time, a W-band PLO is achieved, and the phase noise values of the three signals are measured. It is shown that the experimental result is well coincident with the analysis of phase noise relation.     

Long-term carrier-envelope-phase stabilized fiber-bulk hybrid laser with millihertz linewidth and 50 W average power

Long-term carrier-envelope-phase stabilization was demonstrated in high-power large-modearea fiber chirped-pulse spectral fraction amplification at 1030 nm of a broadband femtosecond Ti:sapphire laser. The carrier enveloped phase was stably controlled with the maximum average power up to 50 W by pre-compensating the carrier-envelope phase changes in the high-power fiber amplifiers. The locked in loop and out of loop frequency fluctuation was measured to be 1.44 and 46 mHz within half an hour. The locked carrier-frequency exhibited an in loop and out of loop beat signal linewidth of 1.66 and 2.27 mHz, accordingly accumulated phase jitter was estimated to be 0.22 and 0.73 rad, respectively, with the integration range from 10 mHz to 100 kHz. The phase stabilization was measured to change little as the output power increased, confirming negligible amplitude-to-phase noise conversions in the linear high-power fiber chirped pulse amplification.     

An electro-acoustics impedance error criterion and its application to active noise control

Characteristics of radiation impedance and its inducing variation of electrical impedance for a controllable source have been investigated. An impedance-based error criterion has been proposed and its application to active noise control is demonstrated through a coil driven loudspeaker. A general formula of radiation impedance is derived for two control strategies, according to the criterion of total acoustic power output. The radiation impedances of some commonly used sound sources are calculated. We discuss in detail the relation between variation of the input electrical impedance and radiation impedance for the two control strategies. An AC-bridge circuit is designed to measure the weak variation of electrical impedance resulted from radiation impedance. The input electrical impedance of a loudspeaker was measured and the experimental result is consistent with that of theoretical analysis. An impedance-based error criterion is proposed since the AC-bridge relative output is unique for a certain control strategy. The implementation of this criterion applied to an active control system is analyzed by simulations. An analogue control system is set up and experiments are carried out in a semi-anechoic chamber to verify the new control approach.     

自适应光学系统波前校正残余误差的功率谱分析方法

采用比较自适应光学系统闭环校正前后时间功率谱人方法,对自适应光学系统的波前校正残余误差进行了分析。在注意噪块时,实测的闭环波前复原相位误差与「实际波前校正残余误差是有区别的,分析了两者功率谱的差别之后,提出了一种估计实际波前校正残余误差的方法,应用这种方法对１．２米望远镜高分辨力自适应光学系统所采集的复原相位数据方差和波前校正残余误差进行了对比。