半导体光放大器增益及发光特性的理论研究

半导体光放大器(SOA)的非线性特性在光开关、波长变换、光逻辑运算中有重要的应用.研究了注入电流、入射光波长及SOA有源区长度对SOA增益和发光功率的影响.数值模拟结果表明:注入电流的增加,会引起载流子浓度的增加,且使SOA增益趋于饱和的速率加快;不同的SOA模型存在一个最佳输入光波长,在此波长附近有较好的增益特性;加长半导体光放大器有源区长度可获得更大增益,同时提高了器件的响应速率.     

基于XGM的SOA波长变换器噪音特性分析及优化设计

利用动态载流子恢复时间可以精确模拟基于交叉增益调制的SOA全光波长变换器的饱和增益效应,本文将SOA分段ASE噪音功率和分段动态模型结合,得到沿长度分布的ASE噪音功率,并讨论了偏置电流、泵浦光和探测光的波长、功率、SOA长度对消光比和信噪比的影响理论计算结果表明,大的偏置电流有利于提高消光比和信噪比;对于一定的输入波长,相对较大的泵浦光和相对较小的探测光变换效果好;SOA的长度存在最佳值.     

增益半导体光放大器的特性

为满足半导体光放大器（SOA）在光纤到户FTTH系统接入网中的广泛应用,提出了基于光纤光栅外腔反馈型GC-SOA结构的全光增益机制,窄线宽激光光源经可变衰减器、隔离器和光纤光栅注入到SOA中,SOA的输出光经隔离器和光纤光栅送至光谱分析仪,通过光纤光栅反馈输入SOA形成钳制激光。对GC-SOA的阈值特性、增益特性及开关特性进行分析,结果表明:当注入电流小于GC-SOA的阈值电流时,增益随注入电流的增加而增加;当注入电流大于GC-SOA的阈值电流后,其增益不再随注入电流的变化而变化,实现了SOA的增益稳定,使SOA的饱和输出功率得到了提高。     

半导体光放大器引起的串扰及其抑制技术

由于半导体光放大器(SOA)的增益饱和效应,在波分复用系统中.每个信道的增益受到复用的其它信道的影响.SOA引起的各信道之间的串扰严重限制了其应用.理论研究了SOA增益饱和效应引起的信道间串扰.数值模拟了多路信道复用时系统的误码率随复用信道数和光功率的变化情况,发现随着复用信道数的增加SOA增益饱和引起的信道间串扰越来越严重.对SOA中串扰的抑制方法进行了理论和实验研究.数值模拟发现连续光注入可以抑制输出功率的波动,从而减小误码率,当复用10个信道时,连续光注入可以使功率代价减小2 dB;实验验证了两信道的40 Gb/s系统中,注入连续光可以减少SOA引起的信道间串扰.     

碲基掺铒光纤放大器增益饱和特性的数值模拟

依据均匀加宽四能级结构速率方程组和光功率传输方程组,数值模拟了1520～1620nm波段范围内碲基掺铒光纤放大器(EDTFA)增益谱特性,以及EDTFA增益谱特性与输入信号光功率的关系.模拟结果显示:随着输入信号光功率的增大,EDTFA增益谱由于饱和效应而呈现平坦化特征.模拟结果与报道的实验测量结果达到了很好的一致.     

考虑端面反射率的半导体光放大器增益特性研究

在考虑到端面反射率影响的前提下,从SOA载流子的速率方程和耦合波方程出发,建立了基于SOA的交叉增益调制波长变换理论模型,利用分段模型方法对影响增益特性的几个参数进行了数值模拟。结果发现,注入电流和有源区面积对SOA增益的影响有一个阈值,在阈值范围内,SOA增益的大小随着注入电流和有源区面积的增大而明显的增大,但是超过阈值时,则SOA增益趋向饱和。     

饱和放大情形下光纤参量放大器的增益和带宽特性研究

利用龙格库塔法数值求解非线性耦合方程,研究了单抽运光纤参量放大器在增益饱和区的增益谱特性.通过比较考虑抽运光损耗与忽略抽运光损耗增益谱的差别,分析了抽运光损耗对增益谱的影响.此外,给出了在饱和放大区,信号光的增益谱与光纤长度、输入信号光功率、抽运光波长与零色散波长偏离之间的关系.发现在饱和放大区,增益的整体水平有所下降,增益谱的可用带宽相对于小信号放大有所减少,增益谱在可用带宽范围内出现了旁瓣.这些结果将对工作在饱和放大区的单抽运光参量放大器的设计提供有益的帮助.     

X波段高功率高增益多注相对论速调管放大器设计

针对器件工程应用中的高功率高增益需求，设计了工作在X波段的高功率高增益多注相对论速调管放大器，建立了带输入、输出波导结构的三维整管模型。设计双边对称耦合孔输入腔结构，降低了输入波导对输入腔间隙电场均匀性的影响以抑制非均匀干扰模式；设计采用多腔多间隙群聚结构，降低了输入微波功率的需求，提高了器件放大增益；并且分析设计了多间隙扩展互作用微波提取结构，提高了器件的功率转换效率以及降低输出结构表面电场强度。通过优化设计，粒子模拟仿真实现X波段多注相对论速调管放大器输出微波功率达到3.2 GW，器件放大增益约为60 dB，功率转换效率约为40%。器件验证实验在电子束电压550 kV，电流5.1 kA的情况下，输出功率为0.99 GW，放大增益约为53 dB，转换效率约为35%。     

语音信号调制的微腔半导体激光器的抗噪音性能

假定微腔半导体激光器输入调制信号为实际语音信号,伴随语音信号的噪音为加性白噪音,在小信号近似下,得到了电流调制和自发发射寿命调制下激光器的传递函数;在大信噪比的前提下,对激光器进行了频域分析,得到了不同参量下的信噪比增益.数值模拟结果表明,在偏置电流的变化范围内,存在极低信噪比增益区,大自发发射因子、小自发发射寿命有利于使该区变窄;语音信号的通带范围和功率谱密度分布特征参量的适当选取,可以使激光器的抗噪音性能在偏置电流的某段范围内得以提高.     

半导体光放大器中光波传输特性研究

根据半导体光放大器(SOA)载流子速率方程和光波在SOA内的传输方程,采用分段的方法计算出光波功率和相位与载流子浓度的关系公式。在泵浦光输入功率分别为5mW和15mW情况下通过仿真得到泵浦光输出波形和归一化转换光波形,其中归一化转换光的波形变化可间接体现不同泵浦光输入功率对SOA内载流子浓度的影响。分析了泵浦光波长和SOA注入电流对探测光的归一化输出、相位和频率啁啾产生的影响。结果表明,随着泵浦光波长的增加,探测光的三种光波特性曲线逐渐趋于平缓。注入电流将会直接影响到SOA的载流子浓度,以此对探测光的输出产生影响,注入电流越大,探测光的频率漂移越远。     

All-optical ultrawideband monocycle generation utilizing gain saturation of a dark return-to-zero signal in a semiconductor optical amplifier

We demonstrate a simple and compact scheme to generate ultrawideband (UWB) monocycle pulses utilizing gain saturation of a dark return-to-zero (RZ) signal in a semiconductor optical amplifier (SOA). When optical pulses with a dark RZ format propagate through the SOA, the output power at the rising edge will be overamplified compared with that at other durations due to the gain unsaturation. As a result, the output pulses are monocyclelike. The UWB frequency spectra at different injected currents, different input pulse widths, and different input wavelengths are analyzed. Our experiments show that the monocycle generation has good tolerance to the SOA bias current and the input signal wavelength.     

集成双波导半导体光放大器光开关实现波长转换的理论研究

建立了基于集成双波导半导体光放大器的光开关(ITG-SOA-Switch)的理论分析模型.与半导体光放大器(SOA)的特性相比较表明，由于ITG-SOA-Switch合并了多种物理效应，故其静态增益饱和曲线在饱和功率点附近具有大幅度陡峭下降的独特性质.理论分析和10 Gbit/s波长转换模拟结果显示，恰当地选择输入抽运光的功率范围，ITG-SOA-Switch波长转换器输出转换光的消光比特性较之输入抽运光会有显著的改善. 关键词： 波长转换 半导体光放大器 集成双波导半导体光放大器 光开关     

基于多电极单端耦合半导体光放大器的交叉增益调制型波长转换器

提出了一种新型的基于多电极单端耦合半导体光放大器(SOA)的交叉增益调制(XGM)型波长转换方案，并建立了这种波长转换器完整的宽带理论模型.通过数值模拟的方法，比较了基于多电极单端耦合SOA的XGM型波长转换和基于单电极单端SOA的XGM型波长转换的输出特性，结果表明前者的输出消光比优于后者，而且啁啾特性也略有改善. 关键词： 多电极 波长转换 单端耦合半导体光放大器 交叉增益调制 消光比 啁啾     

On the output characteristics of a semiconductor optical amplifier driven by an ultrafast optical time division multiplexing pulse train

A comprehensive theoretical analysis of a semiconductor optical amplifier (SOA) that is subject to an ultrafast optical time division multiplexing pulse stream is presented with the help of a simple but efficient model developed for this purpose. The model combines the necessary set of mathematical equations with the appropriate simplifying assumptions to describe in the time domain gain saturation and recovery for the case of multiple incoming pulses. In this manner, analytical expressions can be obtained for the power and chirp profile of the amplified pulses, essentially extending the work that has been performed for a single pulse only. This allows to identify the critical operational parameters and to investigate and evaluate their effect on these two output characteristics. The derived simulation curves are thoroughly studied to specify the limitations imposed on the SOA small signal gain and carrier lifetime as well as on the full-width at half-maximum (FWHM) and energy of the input pulses and, based on a series of logical arguments, to extract useful rules concerning their selection so as to achieve improved performance with respect to the practical applications of all-optical switching and pulse compression. The obtained results indicate that due to the continuous insertion of pulses, the requirements for the SOA small signal gain and the input pulse energy are stringent than those for the case of isolated pulse amplification. The combination of these two parameters determines also the regime in which the amplifier must be biased to operate in order to ensure distortionless pulse amplification and enhanced chirp for efficient pulse compression and it has been found that low saturation is necessary for the former case whilst heavy saturation for the latter. The scopes of the corresponding requirements for the carrier lifetime and the FWHM are also tight but to a less extent and can be simply satisfied with the available photonics technology. These results are in good agreement with the available experimental data essentially proving the validity and robustness of the model. The model can be thus applied to predict the behavior of more complex all-optical circuits of enhanced functionality in which the SOA is the basic functional device.     

Single-SOA-Based Ultrahigh-Speed All-Optical Half Subtracter with PolSK Modulated Signals

A novel ultrahigh-speed all-optical half subtracter based on four-wave mixing (FWM) in a single semiconductor optical amplifier (SOA) is proposed. This scheme only requires a single SOA and two input signals without additional light source, so it is quite simple and compact. Due to the polarization-shift-keying (PolSK) modulated signals being used in this scheme, pattern-dependent degradation can be avoided. By numerical simulation, dependence of the critical factors of the logic gate performance, e.g., the output power of logic 1 and extinction ratio (ER), on two input signals power is investigated. In addition, the effect of the gain polarization dependence of SOA is analysed.     

Generation of 10-GHz duty-cycle tunable square optical pulse in an SOA-based mode-locked fiber laser

We demonstrate the generation of 10-GHz optical square pulses by injecting a picosecond pulse train into an SOA-based mode-locked fiber laser. The novel scheme exploits nonlinear effects and gain saturation phenomenon in the semiconductor optical amplifier (SOA). This technique uses gain-compression dynamics between the input pulses and the generated ones in gain-saturated SOA to form square pulses. The center wavelength of the generated optical square pulse can be tuned from 1530 to 1570 nm by adjusting the center wavelength of the optical band pass filter (OBPF) in the SOA-based mode-locked fiber ring laser. The duty cycle of the output pulse can be tuned from 12.7 to 88.4%, which strongly depends on the input power and intra-cavity power.