高功率蓝光半导体激光加工光源EI北大核心CSCD

针对目前铜、金等金属材料加工的实际应用需求,开展了连续输出功率500 W的光纤耦合输出蓝光半导体激光加工光源研究。基于平面窗口TO封装的蓝光半导体激光单管器件,设计采用长后工作距的快轴准直镜和慢轴准直镜分别准直,获得低发散角、高光束质量的单元准直光束;结合二维空间合束、偏振合束和光纤耦合,将144个蓝光单管器件耦合进200μm/NA 0.22光纤,通过ZEMAX软件对半导体激光光路进行光线追踪模拟;并从实验上实现,3 A电流驱动下,200μm/NA 0.22光纤输出连续功率523 W,电光转换效率29%。该激光光源具有直接加工铜、金等材料的能力。     

基于mini-bar的千瓦级光纤耦合模块

应用ZEMAX光学设计软件对基于min-bar的半导体激光光纤耦合模块进行仿真模拟,采用22只输出功率为60 W的mini-bar半导体激光器组成两列空间叠阵作为耦合光源,通过准直、合束、聚焦等方法高效耦合进入芯径400μm、数值孔径0.22的光纤,输出功率可达1 200 W,光纤耦合效率大于92%。     

基于RGB三基色半导体激光的高功率白激光光源

基于红绿蓝(RGB)三基色直接半导体激光器合成的白激光光源具有转换效率高、显色指数好、输出功率高等优点,是新一代的理想照明光源和显示光源之一。基于RGB三基色半导体激光器件,通过空间合束、波长合束等,三基色光耦合进单光纤,光纤输出合束光功率超过100 W。根据色度学原理进行颜色功率配比,获得了功率达63 W、色温为5 710 K的白光输出,与标准白光D_(65)相比色温偏差小于12.2%。在此基础上,调整红色激光输出功率,获得了功率达58.4 W、色温为6 480 K的白光输出,与标准白光D_(65)相比色温偏差小于3.08%。基于该光源,通过调整激光功率配比,可实现不同色温的合束激光输出。     

Tm3+/Ho3+共掺碲酸盐微结构光纤激光器

用棒管法拉制了Tm³⁺/Ho³⁺掺杂的碲酸盐微结构光纤,并获得了2 μm的激光输出。以1 560 nm的Er³⁺掺杂石英光纤激光器作为泵浦源,在22 cm长的微结构光纤中,得到了最大功率为8.34 mW、波长为2 065 nm的连续激光输出,泵浦光功率为507 mW,斜率效率为2.97%。研究结果表明,Tm³⁺/Ho³⁺共掺碲酸盐微结构光纤是一种用于研制2 μm激光器的理想材料。     

石英基掺Tm3+包层抽运光纤激光器

在MCVD车床上利用“湿法”掺杂方法研制出纤芯高掺Ge的石英基掺Tm³⁺光纤预制棒,采用侧面研磨和抛光工艺制成横截面为正六边形的光纤预制棒.经拉丝,内层涂覆低折射率材料后制成包层抽运光纤.测试其吸收谱,并对光纤参数进行优化.通过在光纤两端紫外写入光纤Bragg光栅,制成线形光学谐振腔,在工作波长793nm的激光抽运下,获得工作波长1947.1031nm、功率2.05W的激光输出.由此证明这种光纤具有优异的光学特性. 关键词： 3+光纤')" href="#">石英基掺Tm³⁺光纤 光纤Bragg光栅 包层抽运 光纤激光器     

高亮度半导体激光阵列光纤耦合模块

利用2只915 nm半导体激光短列阵作为子模块,设计并研制出连续输出的高亮度光纤耦合模块。首先对每个半导体激光短列阵进行光束整形,从而提高它的光束质量;然后采用空间复用技术将这两个半导体激光短列阵出射的激光在光参数积小的方向上叠加,并利用偏振复用技术进一步提高光束质量;最后利用单片非球面透镜将激光聚焦到芯径为100 μm、数值孔径为0.22的光纤中。测量结果显示:在工作电流为52.5 A时,聚焦镜焦平面的光斑尺寸为105.4 μm;耦合后测量光纤出光功率可达72.6 W,对应亮度为6.08 MW/(cm²·sr),模块的电光转换效率为42.2%。最后测量了模块在不同驱动电流时的光谱,证明该模块的散热性能良好。     

200W级高亮度半导体激光器光纤耦合模块

光纤激光器系统需要高可靠性、高亮度、高功率光纤耦合输出二极管激光器模块作为泵浦源。基于mini-bar二极管激光器芯片,采用光束精密准直技术、自由空间合束技术来获得高亮度、高功率光纤耦合输出,针对光纤芯径为200μm、数值孔径为0.22的多模光纤,开展了线偏振二极管激光光纤耦合实验,实验结果表明:光纤稳定输出功率达280 W,对应亮度为5.87 MW/(cm2·sr),电-光效率为45.0%。采用偏振合束技术,光纤预期输出功率可达500 W,对应亮度超过10 MW/(cm2·sr)。该方法可应用于研制数百瓦级高亮度二极管激光光纤耦合输出激光器模块。     

高效率半导体激光器光纤耦合模块

随着半导体激光光源在激光加工领域的应用不断扩展,以激光二极管阵列制成的光纤耦合模块由于存在耦合效率低的缺点,已不能满足激光加工低成本的需求,因此研制高耦合效率的半导体激光器光纤耦合模块变得十分重要。本文将8只波长为808 nm、输出功率为5 W的单管半导体激光器通过合束技术耦合进光纤,制备了一种高效率的半导体激光器光纤耦合模块。光纤芯径为200 μm、数值孔径(NA)为0.22,光纤输出功率为33.2W,耦合效率超过83%,这种高效率半导体激光器光纤耦合模块,可用于激光打标、塑料加工等领域。     

基于偏振保持掺Er3+光纤的高稳定性单波长光纤激光器

研制出光敏偏振保持掺Er³⁺光纤,通过在这种光纤上紫外写入三个光纤光栅,形成对抽运激光高转化效率的谐振腔.在输出功率为23.617dBm、工作波长为976nm的激光抽运下,得到均值功率为9.20dBm、均值中心波长为1554.554nm的单波长激光输出.在室温下800min（约13.3h）的测量时间内,其输出功率的波动为±0.05dB,中心工作波长的波动为±0.0015nm. 关键词： 光纤激光器 3+光纤')" href="#">偏振保持掺Er³⁺光纤 光纤Bragg光栅     

高功率宽带射频调制连续激光源

射频强度调制激光作为激光雷达系统的载波可以有效提高系统的抗干扰和抗散射能力,高功率宽带射频强度调制光源是实现高分辨率远距离探测的关键.本文采用在Nd:YAG激光器的耦合腔中插入一对四分之一波片的方法实现了频差调谐范围为30 MHz—1.5 GHz的双频激光输出,结合光纤振荡功率放大技术,将双频信号光功率放大为50 W.耦合腔双频种子源具有良好的功率和频率稳定性,输出功率为9.5 mW时,功率标准差为0.145 mW,稳定性为1.52%,输出双频激光的频差为250 MHz时,拍频的标准差为1.6144 MHz.种子光进行三级光纤功率放大,得到50 W双频激光输出.放大后的双频激光功率波动范围小于0.1 W,双频拍频的标准差为1.777 MHz,很好地保持了放大之前的功率稳定性和双频频差稳定性.     

Watt-level, high-repetition-rate, mid-infrared pulses generated by wavelength conversion of an eye-safe fiber source

We report on a mid-infrared (mid-IR) source consisting of an approximately 10 W average-power, linearly polarized 1.54 microm wavelength pulsed fiber source pumping an optical parametric oscillator. From this source, we obtained average power in excess of 1 W in the 3.8-4.0 microm wavelength range at a pulse repetition frequency of 100 kHz. With a slightly different setup, we also achieved an average power of 0.25 W at 4.5 microm wavelength. To our knowledge, these values represent the highest mid-IR power obtained through wavelength conversion of an eye-safe fiber source.     

Fiber Raman laser at 1450 nm for medical applications

Raman-fiber source emitting 1450 nm with a power of 1 W was realized. The application of the commercially available pump source with an output power of 35 W allows one to increase the output power up to 5 W. The emission wavelength corresponds to the water absorption band therefore it is promising laser for the surgery and other medical applications.     

High-power tunable single-frequency single-mode erbium:ytterbium codoped large-core fiber master-oscillator power amplifier source

We present a cladding-pumped single-frequency, single-mode erbium:ytterbium codoped fiber master-oscillator power amplifier source generating up to 151 W of continuous-wave output power at 1563 nm with 33% slope efficiency and 20 dB gain. This source was also tunable and had a stable operation range of 1546 to 1566 nm at an output power level in excess of 125 W. The doped fiber exploited a large-core design for improved power handling and mitigation of stimulated Brillouin scattering. There was no sign of having stimulated Brillouin scattering even at the highest power. Despite a large core (V = 12), the output beam was nearly diffraction limited (M2 = 1.1). The source showed slight rollover at over 100 W of output power because of the onset of emission from ytterbium, centered at 1060 nm.     

67.9W高功率全光纤白光超连续谱激光器

利用自主研发的全光纤被动锁模激光器以及高功率光纤模场匹配器,将145 W的皮秒脉冲耦合进国产光子晶体光纤,实现了67.9 W的高功率全光纤结构白光超连续谱输出,光谱范围为500~1700nm,10dB光谱宽度大于1000nm(泵浦波长除外)。整个激光器系统的光-光(半导体泵浦源输出激光-超连续谱输出激光)转化效率达到33.8%。     

High-power, single-mode, linearly polarized, ytterbium-doped fiber superfluorescent source

High-power operation of a single-mode, linearly polarized, broadband superfluorescent fiber source has been achieved by using a two-stage cladding-pumped fiber configuration comprising a low power, single-ended, ytterbium-doped superfluorescent fiber seed source and a high-power cladding-pumped, polarization-maintaining, large-mode-area, ytterbium-doped amplifier pumped by a high-power diode source at 976 nm. The source yielded a maximum linearly polarized output of 106 W with a slope efficiency of up to 67% with respect to the launched pump power and with a measured polarization extinction ratio of 13.5 dB. The wavelength spectrum of the superfluorescent source spanned the range continuously from ~1035 to 1100 nm, and the bandwidth (FWHM) of the emission spectrum was 21 nm. The minimum seed power required for an output power over 100 W was only 10 mW, corresponding to an effective power gain in the amplifier stage of 40 dB. Single-spatial-mode operation with a beam propagation factor (M(2))<1.1 was achieved by bending the amplifier fiber to a bend radius of ~8 cm, without a significant reduction in output power.     

Evolution of the high power THz source program at Jefferson Lab

We report the evolution of the high power THz source program at Jefferson Lab. The source is based on coherent synchrotron radiation in which short bunches of relativistic electrons radiate when traversing a dipolar magnetic field. In our first accelerator we produced 20 W of broadband THz light. Our upgraded accelerator with higher current and improved THz extraction optics will considerably enhance the output power to >100 W. In this paper we describe the source in some detail and present theoretical calculations for the upgrade.     

The energy release and temperature field in the ultracold neutron source of the WWR-M reactor at the Petersburg Nuclear Physics Institute

Results of calculations of energy releases and temperature fields in the ultracold neutron source under design at the WWR-M reactor are presented. It is shown that, with the reactor power of 18 MW, the power of energy release in the 40-L volume of the source with superfluid helium will amount to 28.5 W, while 356 W will be released in a liquid-deuterium premoderator. The lead shield between the reactor core and the source reduces the radiative heat release by an order of magnitude. A thermal power of 22 kW is released in it, which is removed by passage of water. The distribution of temperatures in all components of the vacuum structure is presented, and the temperature does not exceed 100°C at full reactor power. The calculations performed make it possible to go to design of the source.     

96.2 W all-fiberized nanosecond single-frequency fiber MOPA

We report experimental results on a 96.2 W all-fiberized nanosecond single-frequency masteroscillator power amplifier (MOPA) laser working at 1064 nm. An external modulation fiber laser with average power of 0.5 mW and line width of 20 kHz is used as the seed source. Amplifying the seed laser in four stages, a single-frequency laser with pulse duration of 10 ns and peak power of 816.7 W is obtained. The average output power is up to 96.2 W. Further power-scaling of this MOPA structure can be realized since our experiment is only pump-power limited.     

七芯光子晶体光纤中百瓦量级超连续谱的产生

采用平均功率为141.6 W的皮秒光纤激光泵浦一段国产七芯光子晶体光纤,获得了平均功率为104.2 W、连续光谱覆盖范围从750至1700 nm以上的超连续谱输出.详细研究了超连续光谱随泵浦功率增加的演变过程,并对基于该七芯光子晶体光纤的超连续谱光源的光谱拓展和功率提升潜力进行相关的分析和讨论.该研究结果对高功率超连续谱光源的发展具有一定的参考价值.     

用于不锈钢薄板切割的直接半导体激光源

针对高功率半导体激光器存在的光束质量差、单元功率低的缺点,利用合束技术来提高激光功率及光束质量,配合QBH光纤前端帽优化聚焦镜以实现高效耦合。采用11个条宽5.4 mm的迷你线阵合束,通过光束整形、空间合束、偏振合束和波长合束,聚焦耦合进200μm/0.2光纤。在50 A电流下,实现连续386 W输出,功率密度为1.23 MW/cm2,电光效率为43.6%。在200 W的功率下,该激光器可以切割厚度为1 mm的不锈钢薄板。