菱形纤芯光子晶体光纤色散与双折射特性分析

针对光子晶体光纤多零色散点、高双折射的应用要求, 设计了一种新型结构的光子晶体光纤, 其纤芯由位于菱形四个角上的圆形空气孔组成. 通过有限元数值分析方法对该种结构光子晶体光纤的色散特性和双折射特性进行数值仿真, 得到色散与波长、色散与纤芯圆孔尺寸、双折射与波长、双折射与纤芯圆孔尺寸的关系. 研究结果表明:在满足光纤传输功率要求的条件下, 光纤的双折射在d₁<0.8 μupm 时的性能较好. 同时, 该种结构的光子晶体光纤在芯区直径满足d₁=0.4 μupm或 d₁=0.6 μupm时会出现两个零色散点, 这对进一步研制具有多零色散点的光子晶体光纤具有重要的意义.     

基于椭圆孔包层和微型双孔纤芯的新型高双折射光子晶体光纤

设计了一种新型高双折射光子晶体光纤,即其包层引入椭圆形空气孔,且以三角晶格方式周期排列,纤芯引入亚波长尺寸(~0.16 μm)的微型双孔结构阵列.采用全矢量有限元法和各向异性完美匹配层边界条件分析了该型光子晶体光纤的双折射特性和色散特性,详细介绍了该光子晶体光纤在不同的椭圆率、椭圆归一化面积、微型双孔孔径、两小孔之间间距的情况下双折射和限制损耗随波长的变化曲线.模拟结果表明,通过同时在包层和纤芯引入非对称性,获得了较高的双折射(~10^-3量级)和极低(~10^-4 dB/km)的限制损耗.提供了一种新的光子晶体光纤设计方法,即通过同时在包层和纤芯引入新结构来同时获得高双折射和低损耗.     

微结构纤芯对光子晶体光纤基本特性的影响

本文设计了两种具有微结构纤芯的光子晶体光纤（PCFs）——矩形芯和椭圆芯PCFs,利用电磁场散射的多极理论研究了这两种光纤的基本特性.发现在光纤包层气孔不变的情况下,仅通过调节纤芯气孔的大小就可以灵活地调节光纤的双折射、色散和非线性特性.随着纤芯气孔半径r₁的增大,两种纤芯结构的PCFs表现出如下特点：双折射度增大且最大双折射度对应的波长发生红移,零色散波长由一个增加到三个,短波段非线性系数增大而长波段非线性系数减小.r₁=0.4 μm的椭圆芯PCFs的三个零色 关键词： 微结构纤芯光子晶体光纤 双折射 色散 非线性     

基于小圆孔结构纤芯的高双折射光子晶体光纤

为了实现高双折射光子晶体光纤,提出了一种在纤芯中引入微小圆孔的方法.利用全矢量有限元方法和完美匹配层条件研究了基于圆孔微细结构纤芯的光子晶体光纤的双折射特性.讨论了纤芯圆孔数量、孔径、间隔距离对光纤双折射特性的影响;设计了一种双折射达到10－2量级的光子晶体光纤.模拟结果表明采用三个以上圆孔可以获得较大的双折射,增大外包层数目可以有效减小约束损耗.     

基于椭圆孔包层和微型双孔纤芯的新型高双折射光子晶体光纤

设计了一种新型高双折射光子晶体光纤,即其包层引入椭圆形空气孔,且以三角晶格方式周期排列,纤芯引入亚波长尺寸(～0.16 μm)的微型双孔结构阵列.采用全矢量有限元法和各向异性完美匹配层边界条件分析了该型光子晶体光纤的双折射特性和色散特性,详细介绍了该光子晶体光纤在不同的椭圆率、椭圆归一化面积、微型双孔孔径、两小孔之间间...     

低损耗低非线性高负色散光子晶体光纤的优化设计

设计了一种同轴双芯六角点阵光子晶体光纤, 该光纤中心缺失一根空气柱形成内纤芯, 通过减小第4环空气孔的直径形成外纤芯. 采用全矢量有限元法并结合各向异性完美匹配层边界条件, 对其色散、非线性、约束损耗和模场等特性进行了数值模拟. 结果发现, 该光纤呈现高负色散可调效应和较强的模场约束能力, 约束损耗接近10^-2 dB· m^-1. 调整光纤结构参数(即空气孔间隔Λ, 小孔直径d₁和相对孔间隔比f), 可以控制其高负色散工作波长. 若调整光纤结构参数Λ=1.2 μ, f=0.917, d₁=0.515 μm时, 该光纤在低损耗通信窗口C波段呈现负色散和负色散斜率, 其色散斜率在-1----6 ps· km^-1nm^-2范围内波动, 在波长1.55 μm处负色散值为-3400 ps· km^-1nm^-1, 模场面积高达43 μm², 非线性系数仅有3.6 km^-1W^-1. 该光纤在C波段呈现的低损耗低非线性高负色散特性, 具有很好的色散补偿能力, 将在长距离大容量 高功率高速光通信系统中获得很好的应用.     

八边形结构的双折射光子晶体光纤

提出一种新型的双折射光子晶体光纤,在正八边形的基础上改变纤芯附近的几个空气孔的直径产生双折射.利用多极法对该光纤基模的模场分布、色散、限制损耗及双折射特性进行数值分析,并且分析了一些参数对双折射的影响.计算了具有相同参数的六边形结构光子晶体光纤的色散系数、限制损耗及双折射率.研究表明,具有相同参数的八边形结构光子晶体光纤比六边形结构光子晶体光纤的双折射率明显提高,限制损耗大幅度减小,零色散波长也向短波方向移动. 关键词： 光子晶体光纤 双折射 色散 限制损耗     

通过调节纤芯大小实现接近零色散的色散平坦光子晶体光纤

利用已有文献对光子晶体光纤色散特性的计算结果,分析了色散随光子晶体光纤结构参数变化的趋势,并利用有效折射率方法基于标量近似理论对光子晶体光纤色散特性进行了有目的性的数值模拟,发现通过独立调整纤芯大小,可以在光通信波段实现非常接近零色散的色散平坦光子晶体光纤,其色散系数D的绝对值在1.3 μm～2.0 μm波长范围小于1.5 ps·km-1·nm-1 .     

八边形高双折射双零色散点光子晶体光纤特性分析

针对光纤通信和传感系统中高双折射、多零色散点的应用需求, 设计了一种新型结构的光子晶体光纤.该结构包层为圆形空气孔按照八边形形状排列而成, 并在内包层对称位置中加入两个椭圆空气孔以获得高双折射特性. 通过有限元数值分析方法对光纤特性进行分析,仿真结果表明,该结构光子晶体光纤在波长0.8—2 μm 范围内双折射可达10^-3量级,满足高双折射的应用需求,并且满足两个零色散点的应用需求. 同时光纤的非线性系数达10^-2·m^-1·W^-1量级,可应用于对非线性要求较高的场合.     

Ge20Sb15Se65硫系玻璃光子晶体光纤的中红外色散特性

硫系玻璃与石英玻璃相比具有高折射率(2.0~3.5)、低声子能量 (<350 cm^-1)、优良的中远红外透过性能(可至25 μm)等特性.本文制备了一种在中红外具有优良透过特性的无As环保型Ge₂₀Sb₁₅Se₆₅硫系玻璃材料,以此为基质材料设计了一种三层空气孔结构光子晶体光纤,利用多极法对光纤的中红外色散特性进行了数值模拟,系统研究了结构参量孔径d、孔间距Λ 以及d/Λ 对其色散特性的影响.分析表明:通过改变包层空气孔直径d或空气孔间距Λ,可灵活的调节光子晶体光纤的零色散波长向短波或长波方向移动.通过优化结构参量发现,当Λ=3 μm,d/Λ=0.35 附近变化时,可获得3~5 μm色散平坦,且色散值小于5 ps·nm^-1·km^-1的光子晶体光纤.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.