紫外光引发阳离子聚丙烯酰胺的红外光谱研究

以丙烯酰胺(AM)、 丙烯酰氧基乙基三甲基氯化铵(DAC)、 丙烯酸丁酯(BA)为单体,采用紫外光引发聚合制备阳离子聚丙烯酰胺P(AM-DAC-BA)。 采用紫外光谱和红外光谱研究其结构特征;分析AM,DAC,BA,P(AM-DAC-BA)的红外光谱中的典型红外振动频率的归属。 通过与单体红外光谱比较得出：由于聚合产物的对称性增加,聚合产物红外光谱更加简单。 P(AM-DAC-BA)的特性粘度随着光强、 BA含量、 光引发剂浓度、 光照时间的增加而增加。 选取AM,DAC,BA中的—CONH₂,—COOCH₂(CO), —COOCH₂—(C—O—C),—CH₂—N+(CH₃)₃基团吸收峰为特征吸收峰,随着光强、 BA含量的增加,特征峰面积增加;随着光引发剂浓度增加特征峰面积却呈现减少趋势;随着光照时间增加,峰面积是先减小后增加。 但不同P(AM-DAC-BA)在红外光谱上对应的特征吸收峰的峰型类似,特征峰位置基本一致。     

制备腈菌唑分子印迹聚合物前功能单体选择研究

为制备腈菌唑(M)分子印迹聚合物,建立了选择合适的功能单体以及功能单体添加量的方法。利用紫外光谱法研究α-甲基丙烯酸(MAA)、丙烯酰胺(AM)与M作用形式、作用强度、最佳浓度比和形成的结合位点数。结果表明,M与两种功能单体都会形成氢键;M的三唑环共轭双键的π电子吸收能量跃迁到π*共轭反键轨道,氢键的形成会使π→π*的吸收带发生迁移,最大吸收波长随着体系功能单体浓度增加而发生红移。M与两种功能单体最佳浓度配比分别为:M∶MAA=1∶4和M∶AM=1∶2。M与两种功能单体都具有结合能力,且结合力较强。采用AM为功能单体合成的分子印迹聚合物对M具有更好的稳定性和特异识别能力。     

紫外光辐射法表面接枝改性PET膜

用二苯甲酮(BP)做光引发剂,聚对苯二甲酸乙二醇酯(PET)薄膜用丙烯酸进行紫外光照表面接枝改性。丙烯酸接枝率随光照时间、单体浓度增加而增加,并随引发剂浓度的变化而变化.光照时间为1h,引发剂的浓度为5×10-3mol/L,丙烯酸浓度为6%(wt%)时,接枝效果最好.通过接枝反应,羧基(—COOH)被引入到PET膜表面,提高了PET膜的亲水性和碱性染料的可染性。     

无皂阳离子MMA/HEMA胶乳粒子的制备及表征

讨论了微波辐照下带正电荷的自由基引发剂偶氮二异丁基脒盐酸盐 (AIBA)引发甲基丙烯酸甲酯(MMA)和甲基丙烯酸 2 羟乙酯 (HEMA)共聚 ,用透射电子显微镜、红外光谱仪、差热分析仪等对聚合产物进行表征 .结果表明 :两种单体发生了共聚反应 ,制得均分散、表面洁净的无皂阳离子胶乳粒子 ;粒子的粒径随着单体HEMA浓度的增加先减小后增加 .在微波辐照下共聚反应的速率非常快 ,几乎所有的反应在 2 0min之内就能完成 .随着单体HEMA浓度的增加 ,乳液抗电解质稳定性提高     

多孔塑料光纤氨传感探头的制备与应用

基于交联共聚技术,以藻红为荧光指示剂,苯乙烯为聚合单体、双甲基丙烯酸一缩二乙二醇酯为交联剂,研制了苯乙烯聚合多孔塑料光纤,用于微量氨的传感分析。研究了荧光指示剂在共聚体中的固定技术,考察了传感探头在不同聚合交联度、惰性致孔剂、荧光指示剂浓度条件下对氨的响应性能的影响。在最优条件下,聚苯乙烯多孔塑料光纤探头透明、刚性、耐水和耐化学性能好,透光率为88%—92%,对氨的检测线性浓度范围为2×10~(-4)—9.1×10~(-3)mol/L,并具有较好的稳定性和可逆性。     

微模塑法制备PMMA/SiO2二氧化硅杂化材料微结构

以摩尔比为 1∶1的甲基丙烯酸甲酯 (MMA)、甲基丙烯酸 (3 三乙氧基硅烷基 )丙酯 (ESMA)单体、0 .2 %(单体总量的质量分数 )的偶氮二异丁腈AIBN引发剂和四氢呋喃 (THF)溶剂 ,及 2 0 % (总质量分数 )的正硅酸乙酯TEOS合成出PMMA/SiO2 有机 无机杂化的杂化溶胶 .将溶胶在洗净的普通光学玻璃基片表面甩膜 .利用软刻蚀中的微模塑法 ,把有机硅弹性印章复制有精细图纹一面轻放在杂化溶胶膜上进行微模塑 ,外加 1N压力于12 0℃下处理 2h使溶胶凝胶化 .印章剥离后在基片表面就形成了PMMA/SiO2 有机 无机杂化材料的微图纹结构 .从微图纹的光学显微镜照片可以看出微模塑方法制备杂化材料复制的图纹精细度高 ,操作简单易行 ,是一类比较理想的微细图纹结构加工的方法 .     

反相高效液相色谱法测定合成产物2-硝基芴酮的含量

建立了一种反相高效液相色谱法测定2-硝基芴酮含量的方法。液相色谱条件为:EliteHypersil ODS2C18色谱柱(4.6mm×250mmi.d.,5μm),甲醇-四氢呋喃-水为流动相(体积比为65∶15∶35)。在流速1.0mL/min,检测波长254nm,柱温25℃条件下,产物2-硝基芴酮与原料芴酮、副产物2,7-二硝基芴酮在2-硝基芴酮浓度为5—30mg/L范围内分离效果良好,峰面积与质量浓度呈良好的线性关系,相关系数为0.9985;平均回收率值大于99.00%,相对标准偏差小于1.00%。结果表明,该方法具有操作简便、精密度和准确性高的特点,可适用于工业生产2-硝基芴酮含量的测定。     

高分子网络凝胶法低温合成YAG∶Tb3+荧光粉

以金属硝酸盐为原料,丙烯酰胺为聚合单体以及N,N-亚甲基双丙烯桥酰胺为胶联剂,采用高分子网络凝胶法在低温下合成精细粒度Y3Al5O12∶Tb3 (YAG∶Tb3 )荧光粉.分别用热重-差热分析(TG-DTA)、X射线衍射(XRD)、扫描电子显微镜(SEM),以及激发和发射光谱测量对样品进行了表征,考察了烧结温度对样品结晶程度、颗粒大小的影响,以及样品发光性能与烧结温度和Tb3 浓度的关系.结果表明:YAG晶相形成温度为850℃;粉体颗粒大小均匀,随着烧结温度的升高,颗粒粒径增大,结晶程度提高;观察到Tb3 中4f-5d的吸收带以及5D4-7Fj(j=6,5,4,3)的特征发射带,最强吸收与最强发射分别发生在272,541.8 nm,与量子理论(E=1.24/λ)的计算结果相吻合,其发光强度随烧结温度的升高而增强;观察到了Tb3 在Y3Al5O12中的浓度猝灭现象.     

合成聚肽嵌段共聚物PHEG-PBLG结构的核磁共振分析

通过L-谷氨酸苄酯和三光气反应制备谷氨酸苄酯的N-羧酸酐,以聚羟乙谷氨酸酰胺为大分子引发剂,投入不同配比的单体/引发剂（A/I）,共聚得到两亲性嵌段共聚物聚羟乙谷氨酰胺-聚谷氨酸苄酯（PHEG-PBLG）;通过核磁共振技术分析表征该合成聚肽的结构组成、分子量范围及螺旋结构;通过体外酶解实验研究了共聚物的降解情况. 研究结果表明：该合成聚肽化合物为两亲性嵌段聚合物：当聚合物中亲水链段PHEG分子量为9000,A/I为75∶1, 100∶1, 150∶1, 200∶1时,相应的共聚物的分子量分别为：1.27×10⁴,1.75×10⁴, 1.9×10⁴, 3.60×10⁴;该合成聚肽含有α-螺旋结构, 随着TFA的加入,该聚肽的结构由α-旋构象转化为随机盘绕构象.     

12CaO·7Al_2O_3∶Ce~(3+)透明陶瓷的制备及其闪烁特性研究

采用高温固相法制备了不同Ce3+掺杂浓度的12Ca O·7Al2O3(C12A7∶x%Ce3+)陶瓷样品。在350 nm紫外光激发下,样品的发射光谱呈现为主峰位于440 nm的宽带,来源于Ce3+的5d1→2F5/2和2F7/2的辐射跃迁。随着Ce3+掺杂浓度的增加,发射强度增大;当Ce3+摩尔分数超过0.7%时,有杂质相出现。为了进一步提高光致发光强度,采用自蔓延燃烧法合成了C12A7∶0.5%Ce3+陶瓷样品。在H2气氛下热处理,通过改变笼中阴离子基团的种类和数目提高了陶瓷闪烁特性(发光强度和衰减时间)。结果表明,C12A7∶Ce3+陶瓷是可应用于闪烁体的潜在材料。     

Properties of Absorbent Acrylic Foam Prepared Based on the Method of High Internal Phase Emulsion

Acrylate and methacrylate monomers absorbent acrylate foams were prepared based on the method of high internal phase emulsion (HIPE). The influence of reaction conditions on liquid absorption by acrylate foams was studied. The reaction conditions included monomer ratio, cross-linker amount, initiator amount, emulsifier amount, emulsion concentration, emulsification temperature, and the curing time. The reaction conditions were determined to achieve the best liquid absorption by acrylate foams. Acrylate foams were analyzed with Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results showed that when the monomer ratio was 9:1, cross-linking agent was 30% of monomer amount, initiator amount was 4% of the reactants amount, emulsifier amount was 8% of the reactants amount, the ratio of aqueous phase to oil phase was 32:1, emulsification temperature was 75°C, and curing time was 1.5 h, we could prepare the acrylate foam material with the best liquid absorption. Reaction of monomer and cross-linking agent was confirmed by FTIR analysis. The pore sizes of acrylate foam were between 1 μm and 8 μm according to SEM analysis. This material was very suitable to absorb aqueous fluids.     

Preparation and Properties of Water-Soluble Sodium Polyacrylates

Butyl acrylate-acrylic acid copolymer and poly (butyl acrylate) were synthesized via suspension polymerization by using butyl acrylate as the main monomer and acrylic acid as a secondary monomer. Then these polymers were swollen in ethanol and hydrolyzed in an aqueous solution of sodium hydroxide. Finally, water-soluble sodium polyacrylates were obtained by washing and drying the hydrolyzed resultant. The influence of the mass fraction of acrylic acid in the monomer feed ratio, swelling time, and hydrolysis time on hydrophilicity, solubility, and absolute viscosity of the prepared sodium polyacrylates was researched. In addition, an Ubbelohde viscometer was used to determine the intrinsic viscosity of the aqueous solutions of the prepared sodium polyacrylates. The Mark–Houwink equation was applied to calculate their viscosity average molecular weight. Finally, their chemical structures and heat resistance properties were analyzed by using nuclear magnetic resonance spectroscopy and thermogravimetric analysis; additionally, the changes of the surface elements before and after hydrolysis were researched by using X-ray photoelectron spectroscopy.     

Swelling assisted photografting of itaconic acid onto sodium alginate membranes

Grafting of itaconic acid (IA) was achieved onto sodium alginate (NaAlg) membranes by using UV-radiation. Process was performed under nitrogen atmosphere and benzophenone (BP) was used as a photoinitiator. Membranes were preswelled before the polymerization process and ethanol was determined as the best swelling agent among the studied solvents. The effect of polymerization time, initiator and monomer concentrations on the grafting efficiency were investigated. The best conditions for optimum grafting were obtained with IA concentration of 1.0 M, a BP concentration of 0.1 M and a reaction time of 4 h at 25 °C. Under these conditions grafting efficiency for NaAlg-g-IA membranes was found to be 14% (w/w). To obtain further increase in grafting efficiency membranes were also preswelled in IA and BP solutions and polymerization was carried out at different temperatures after UV polymerization. Grafted membranes were characterized by using Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Effect of grafting on membrane properties such as intrinsic viscosity and swelling percentage were also determined.     

Sensitivity Enhancement in Uranium Determination by UV-Visible Spectroscopy Using Ion Imprinted Polymer

There is need to determination of uranium concentration at ppb level in environmental matrices. Due to low sensitivity of FAAS, UV-Visible Spectroscopy is generally used as measurement technique. In this study, ion-imprinted polymers (IIP) were prepared for uranyl ion (imprint ion) by formation of ternary (salicylaldoxime and 4-vinylpyridine) complex in 2-methoxy ethanol (porogen) following copolymerization with methacrylic acid (MAA) as a functional monomer and ethylene glycol dimethacrylate (EGDMA) as crosslinking monomer using 2,2-azobisisobutyronitrile as initiator. The synthesized polymers were characterized by FT-IR and TGA analysis. Arsenazo Ⅲ in 3 M HClO₄ was used as complexing agent in the measurement step. The optimal pH for preconcentration was found to be between 3.5～6.5 values. The developed method was applied to uranium (Ⅵ) determination in natural water samples.     

分子印迹技术特异性识别头孢类分子的光谱研究

以头孢氨苄(CFL)为特异性分析识别对象,采用本体聚合和悬浮聚合两种聚合方法,制备了头孢氨苄分子印迹聚合物.紫外光谱研究证实模板分子CFL与内烯酰胺之间形成氢键型配合物.用红外光谱法分析了CFL分子印迹聚合物的聚合程度及聚合物表面上存在的功能基团.紫外光谱分析表明,用AM-EGD-MA体系和本体聚合法制备的印迹聚合物对...     

Synthesis and Characterization of Terpolymers of poly(L-lactide-glycolide-ε-caprolactone)

Random terpolymers of poly(L-lactide-glycolide-ε-caprolactone) (PLLGC) was prepared by ring-opening polymerization of L-lactide, glycolide and ε-caprolactone monomers initiated with stannous octanoate. Fourier transform infrared spectra, nuclear magnetic resonance and gel permeation chromatography were employed to characterize the obtained PLLGC terpolymers. The effects of polymerization temperature, reaction time, the amount of initiator and the polymerization pressure on the weight average molecular mass and polydispersity index of the PLLGC were investigated. In addition, the water contact angle of the PLLGC was also tested. The characterization of chemical structure showed that the PLLGC was successfully synthesized. For instance, a PLLGC terpolymer with a weight average molecular mass of about 12.435?×?10⁴?Da and a polydispersity index of 1.28 was obtained when the polymerization was conducted with a molar ratio of monomer to initiator ([M]/[I]) of 2000, polymerization temperature of 140?°C, polymerization pressure of 5.0?Pa and reaction time of 24?h. The random incorporation of ε-CL monomer units decreased the wettability of the PLGA copolymers.     

Synthesis and Characterization of Methylacrylic Acid and Butyl Acrylate Grafted onto Ethylene-Propylene-Diene Terpolymer

A multi-component polymer of methacrylic acid (MAA) and butyl acrylate (BA) grafted onto ethylene-propylene-diene (EPDM) terpolymer was synthesized in toluene using benzoyl peroxide (BPO) as initiator. The effect of EPDM/MAA-BA ratio and MAA/BA ratio on the grafting ratio of polymerization was investigated. The products were characterized by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), surface energy, inherent viscosity, and atomic force microscopy (AFM). The results showed that the MAA and BA monomers were successfully grafted onto EPDM. Furthermore, after being grafted, the polarity of the surface of the EPDM-g-MAA-BA increased with increasing grafting ratio, and the morphology of its surface became more smooth.