An All-Solid-State Tunable Dual-Wavelength Ti：Sapphire Laser with Quasi-Continuous-Wave Outputs

A high power dual-wavelength Ti：sapphire laser system with wide turning range and high efficiency is described, which consists of two prism-dispersed resonators pumped by an a11-solid-state frequency-doubled Nd：YAG laser. Tunable dual-wavelength outputs, with one wavelength range from 750nm to 795nm and the other from 80Ohm to 850nm, have been demonstrated. With a pump power of 23 W at 532nm, a repetition rate of 6.5kHz and a pulse width of 67.6ns, the maximum dual-wavelength output power of 5.6 W at 785.3nm and 812.1 run, with a pulse width of 17.2ns and a line width of 2nm, has been achieved, leading to an optical-to-optical conversion efficiency of 24.4%.     

超宽带近红外和蓝光飞秒激光脉冲产生的实验研究

增益介质中泵浦光束提供的软光阑效应对于实现克尔透镜稳定锁模及其超宽带光谱脉冲的产生具有非常重要的作用.实验上首先对半导体泵浦全固化钛宝石飞秒激光器的锁模动态特性进行了研究,在4 W绿光泵浦状态下获得了平均输出功率为570 mW、中心波长在794 nm～835 nm范围内调谐、光谱带宽最大可达135 nm的近红外光脉冲输出,其相应的时域变换极限脉冲宽度均小于10 fs.另外,将光束聚焦在超薄BBO晶体上,获得了中心波长在418 nm～429 nm之间调谐、光谱宽带时域变换极限小于15 fs的蓝光飞秒脉冲.     

An all-solid-state high power quasi-continuous-wave tunable dual-wavelength Ti：sapphire laser system using birefringence filter

This paper describes a tunable dual-wavelength Ti:sapphire laser system with quasi-continuous-wave and high-power outputs. In the design of the laser, it adopts a frequency-doubled Nd:YAG laser as the pumping source, and the birefringence filter as the tuning element. Tunable dual-wavelength outputs with one wavelength range from 700~nm to 756.5~nm, another from 830~nm to 900mn have been demonstrated. With a pump power of 23~W at 532~nm, a repetition rate of 7~kHz and a pulse width of 47.6~ns, an output power of 5.1~W at 744.8~nm and 860.9~nm with a pulse width of 13.2~ns and a line width of 3~nm has been obtained, it indicates an optical-to-optical conversion efficiency of 22.2{\%}.     

Self-starting mode-locked picosecond Ti：sapphire laser by using of a fast SESAM

A stable continuous wave mode-locked picosecond Ti:sapphire laser by using a fast semiconductor saturable absorber mirror (SESAM) is demonstrated. The laser delivers pulse width of 20 ps at a central wavelength of 813 nm and a repetition rate of 100 MHz. The maximum output power is 1.34 W with pump power of 7 W which corresponds to an optical--optical conversion efficiency of 19.1%.     

High-power, continuous-wave Ti:sapphire laser pumped by fiber-laser green source at 532 nm

We report the first experimental demonstration of efficient and high-power operation of a Ti:sapphire laser pumped by a simple, compact, continuous-wave (cw) fiber-laser-based green source. The pump radiation is obtained by direct single-pass second-harmonic-generation (SHG) of a 33 W, cw Yb-fiber laser in a 30-mm-long MgO:sPPLT crystal, providing 11 W of single-frequency green power at 532 nm in TEM₀₀ spatial profile with power and frequency stability better than 3.3% and 32 MHz, respectively, over 1 h. The Ti:sapphire laser is continuously tunable across 743-970 nm and can deliver an output power up to 2.7 W with a slope efficiency as high as 32.8% under optimum output coupling of 20%. The laser output has a TEM₀₀ spatial profile with M²<1.44 across the tuning range and exhibits a peak-to-peak power fluctuation below 5.1% over 1 h.     

High power all-solid-state quasi-continuous-wave tunable Ti: sapphire laser system

This paper reports a high power, all-solid-state, quasi-continuous-wave tunable Ti:sapphire laser system pumped by laser diode (LD) pumped frequency-doubled Nd:YAG laser. The maximum tuned output power of 4.2 W (797 nm) and tuned average power of 3.7 W were achieved when fixing the Ti:sapphire broadband output power at 5.0 W and applying 750-850 nm broadband coated mirror.     

Analysis of tunable picosecond pulse generation from a distributed feedback Ti：sapphire laser

A distributed feedback Ti:sapphire laser (DFTL) pumped by a 532nm Q-switched pulse is proposed for the generation of tunable picosecond pulses. With coupled rate equation model, the temporal characteristics of DFTL are obtained. The numerical solutions show that the DFTL pulse with a 50-ps pulse duration and as much as 3.SmJ pulse energy can be obtained under 40-m J, 5-ns pulse pumping. The dependence of output pulse width on the laser crystal‘s length, pumping pulse duration, and pumping rate is also discussed in detail.     

Generation of 7-fs laser pulse directly from a compact Ti:sapphire laser with chirped mirrors

A compact femtosecond Ti:sapphire laser resonator consisting of three chirped mirrors and one output coupler was designed. By accurately balancing the intra- cavity dispersions between Ti:sapphire crystal, air and chirped mirrors, we directly generated the laser pulse shorter than 7 fs at the average power of 340 mW with 3.1 W pump. The repetition rate of the laser oscillator is 173 MHz at the centre wavelength of 791 nm, and the ultrabroaden spectrum covers from 600 nm to 1000 nm. To the best of our knowledge, this is the simplest laser resonator capable of generating sub-10 fs laser pulse.     

Tunable, low-repetition-rate, cost-efficient femtosecond Ti:sapphire laser for nonlinear microscopy

We report on a broadly tunable, long-cavity Ti:sapphire laser oscillator being mode-locked in the net negative intracavity dispersion regime by Kerr-lens mode-locking, delivering τ _FWHM<300 fs pulses at 22 MHz repetition rate. The wavelength of the laser can be tuned over a 170 nm wide range between 712 nm and 882 nm. Having a typical pump power of 2.6 W, the maximum pulse peak power is 60 kW. Comparison of the reported laser with a standard, 76 MHz Ti:sapphire oscillator regarding two-photon excitation efficiency in a laser scanning microscope shows that the 22 MHz laser generates the same fluorescence signal at considerably, 1.82 times lower average power, which is expected to result in a reduced photothermal damage probability of biological samples. This fact along with the broad tunability and a low pump power requirement makes this cost-effective laser an ideal light source for nonlinear microscopy.     

高效全固化紫外四倍频激光器的研究

用半导体激光器抽运的调Q YLF倍频激光器抽运掺钛蓝宝石激光器，用LBO晶体在腔内产生二次谐波，再聚焦到BBO晶体上产生四次谐波深紫外激光。为了提高谐波转换效率，在腔内分别插入了单片、组合双折射滤光片和聚焦透镜，在平均功率为3.6W，波长为527nm的抽运光下得到410mW，417nm的蓝光。用长焦距的透镜聚焦二次谐波，得到34mW，208nm的紫外脉冲激光。从实验上详细研究了基频光的线宽对二次谐波效率的影响，二次谐波的线宽对四次谐波效率的影响、基频光的波长对四次谐波产生效率的影响。全面地分析了单片和组合大拆射滤光片及抽运功率对钛蓝宝石激光器基频光的脉宽、线宽等参量的影响。     

4.5MW小型化全固态腔倒空飞秒掺钛蓝宝石激光器

研制了国内首台腔倒空克尔透镜自锁模掺钛蓝宝石激光器,该激光采用二极管抽运的全固态连续波532nm激光抽运.在5.4W的抽运功率下,获得了峰值功率大于4.5MW、脉宽小于18fs的稳定锁模脉冲,其重复频率可低至20kHz,所占尺寸约53.5cm×20.5cm.据知,此结果是迄今重复率最低、结构最紧凑的声光腔倒空飞秒激光器件 关键词： 掺钛蓝宝石 腔倒空 飞秒脉冲 克尔透镜锁模     

LD侧面泵浦电光调Q532nm脉冲激光器

 为了实现高可靠、窄脉宽、高峰值功率激光输出,采用侧面泵浦技术和电光调Q技术,设计出一种激光二极管侧面泵浦电光调Q全固态绿光激光器。采用结构简单、紧凑的平-平腔设计,其端镜和输出镜均为平面镜,获得较稳定的侧面泵浦Nd∶YAG腔外倍频KTP脉冲绿光激光输出。当泵浦电流为120A,重复频率为600Hz时,获得脉冲绿光的最高输出平均功率为3.62W,1064nm到532nm的转换效率为15.3%,其脉宽为21ns,峰值功率为300kW, 单脉冲能量为6.01mJ。实验结果表明：该激光器稳定性可靠,输出激光脉宽较窄、峰值功率高。     

High-power passively Q-switched Nd:YVO<Subscript>4</Subscript> UV laser at 355 nm

We report on an efficient high-power passively Q-switched UV laser at 355 nm. We take into account the second threshold criterion and the thermal-lensing effect to design and realize a compact reliable passively Q-switched Nd:YVO₄ laser with Cr⁴⁺:YAG as a saturable absorber. At an incident pump power of 16.3 W, the average output power at 1064 nm reaches 6.2 W with a pulse width of 7 ns and a pulse repetition rate of 56 kHz. Employing the developed passively Q-switched laser to perform the extra-cavity harmonic generations, the maximum average output powers at 532 nm and 355 nm are up to 2.2 W and 1.62 W, respectively.     

A double-pass optical parametric amplifier seeded by a blue-shifted output of a photonic-crystal fiber

A blue-shifted output of a photonic-crystal fiber, providing a frequency upconversion of femtosecond Ti:sapphire laser pulses, is used to seed a double-pass optical parametric oscillator (OPA). The OPA is based on a BBO crystal, pumped by 65-mW 150-fs second-harmonic pulses of a Ti:sapphire laser. Gain factors in excess of 10³ are demonstrated for such an OPA, yielding tunable light pulses within the range of wavelengths from 420 to 650 nm, a peak power up to 250 kW, and a typical pulse width of about 200 fs at a repetition rate of 100 kHz. PACS 42.81.Gs; 42.81.Qb     

采用多通腔望远镜谐振腔结构的10MHz重复频率飞秒钛宝石激光器特性研究

通过在钛宝石激光腔内引入望远镜长腔系统增加腔长,实现了重复频率低到10?MHz的飞秒激光振荡,在5?W的抽运功率下获得了平均输出功率200?mW、单脉冲能量20?nJ的稳定输出. 在此基础上分析了腔内不同色散情况下的输出脉冲光谱和脉宽特性,结果表明在腔内存在一定负色散的情况下,锁模脉宽可接近转换极限,最短脉宽可达56?fs. 而在正色散的情况下,锁模输出的脉宽较宽,并且随着腔内正色散的增多,脉宽可到大于600?fs,锁模光谱也呈马鞍形. 关键词： 钛宝石激光器 飞秒脉冲 低重复频率 望远镜腔     

Tunable femtosecond laser in the visible range with an intracavity frequency-doubled optical parametric oscillator

We demonstrated experimentally a synchronously pumped intracavity frequency-doubled femtosecond optical parametric oscillator (OPO) using a periodically-poled lithium niobate (PPLN) as the nonlinear material in combination with a lithium triborate (LBO) as the doubling crystal. A Kerr-lens-mode-locked (KLM) Ti:sapphire oscillator at the wavelength of 790 nm was used as the pump source, which was capable of generating pulses with a duration as short as 117 fs. A tunable femtosecond laser covering the 624-672 nm range was realized by conveniently adjusting the OPO cavity length. A maximum average output power of 260 mW in the visible range was obtained at the pump power of 2.2 W, with a typical pulse duration of 205 fs assuming a sech2 pulse profile.     

100-TW sub-20-fs Ti:sapphire laser system operating at a 10-Hz repetition rate

We developed a compact three-stage Ti:sapphire amplifier laser system that produced peak power in excess of 100 TW for a pulse duration of less than 19 fs and an average power of 19 W at a 10-Hz repetition rate. A final 40-mm-diameter Ti:sapphire amplifier is pumped by a Nd:YAG master-oscillator-power-amplifier system that produces ~7-J output of 532-nm radiation. The spatial beam quality is approximately 2 times diffraction limited for the full amplified compressed output pulse. With f/3 optics, this system should therefore be capable of producing a focused intensity of ~3x10(20) W/cm(2) .     

MW级峰值功率掺钛蓝宝石激光振荡器

在常规重复频率77 MHz掺钛蓝宝石飞秒激光器的基础上,通过腔内引入Herriott型多通望远镜系统增加总腔长及对腔内色散的深入分析和实验控制,实现了低重复频率、高脉冲能量飞秒激光振荡的稳定运行.在连续功率8.2 W的532 nm激光抽运下,得到了重复频率11 MHz、单脉冲能量达72.73 nJ、对应峰值功率MW量级的结果.相对80 MHz重复频率下6.25 nJ的单脉冲能量及150 kW的峰值功率,其输出能力提高了约一个量级. 关键词： 飞秒激光 掺钛蓝宝石激光器 低重复频率 MW     

Efficient 532 nm laser using high gray-tracking resistance KTP crystal

A LD end-pumped acoustic-optic Q-switched intracavity frequency-doubled Nd:YVO₄ laser was demonstrated. It uses a high gray-tracking resistance KTP crystal as nonlinear optical crystal. The output characteristics of 532 nm green laser using different doping concentrations and cavity configurations were investigated. With the pump power of 27.5 W, a maximum average power of 13 W at 532 nm was achieved at a pulse repetition rate of 80 kHz, corresponding to the optical-to-optical efficiency of 47.3%. The pulse width is 30 ns and single pulse energy is up to 162.5 μJ. This work is a significant exploration for using a high gray-tracking resistance KTP crystal to generate highly efficient frequency-doubled green laser.     

Littrow-type discretely tunable, Q-switched Nd:YAG laser around 1.3 μm

An all-solid-state, side diode array pulse pumped Nd:YAG laser tunable for six wavelengths ranging from 1318.8 nm to 1356.0 nm is developed. The tunability is obtained by using a grating in Littrow mode that also serves as an output coupler. The configuration ensures a line width as low as 0.04 nm. Thermal effects limit the maximum average power to 250 mW for an average absorbed pump power of 8.0 W in the free-running condition. An acousto-optic Q-switching of the laser provides pulses of width 251 ns with peak power of 733 W for an average pump power of 11.5 W. The laser may find application in microsurgery and dermatology. PACS 42.55.Xi; 42.60.-v; 42.60.Fc; 42.60.Gd; 42.62.Be