Measurement of dose enhancement by neutron capture of boron in Cf interstitial brachytherapy

The effect of boron concentration in water on the gamma, fast and slow neutrons and alpha particles components at the central, forward and backward surfaces inside tumor phantom of 4.2 cm diameter and 4.4cm height, during brachytherapy by neutrons from ²⁵²Cf were investigated. The source was at the centre of a cubic shaped water phantom of 30 cm side. The study was carried for different concentrations of boron from H₃BO₃, Li₂B₄O₇ and H₃¹⁰BO₃. The effect of source to tumor distance on the different components of radiation was also measured. The results indicated that the use of ¹⁰B compounds enhances the damage and is recommended for successful boron neutron capture therapy (BNCT).     

Investigation of 1.3 μm emission in Nd-doped bismuth-based oxide glasses

Nd₂O₃-doped 43Bi₂O₃–xB₂O₃–(57−x)SiO₂–1.0Nd₂O₃ (x=57, 47, 39, 28.5, 19.5, 10, 0 mol%) bismuth glasses were prepared by the conventional melt-quenching method, and the Nd³⁺: ⁴F_3/2→⁴I_13/2 fluorescence properties had been studied in an oxide system Bi₂O₃–B₂O₃–SiO₂. The Judd–Ofelt analysis for Nd³⁺ ions in bismuth boron silicate glasses was also performed on the basis of absorption spectrum, and the transition probabilities, excited-state lifetimes, the fluorescence branching ratios, quantum efficiency and the stimulated emission cross-sections of ⁴F_3/2→⁴I_13/2 transition were calculated and discussed. The stimulated emission cross-sections of 1.3 μm were quite large due to a large refractive index of the host. Although the effective bandwidths decreased with increasing SiO₂ content, quantum efficiencies and stimulated emission cross-sections enhanced largely with increasing SiO₂ content.     

The role of Sb(5+) in the structure of Sb(2)O(3)-B(2)O(3) binary glasses--an NMR and Mössbauer spectroscopy study

Glasses of general formula xSb₂O₃ (1−x)B₂O₃ (0x0.8) have been prepared by conventional melt- quenching. Mössbauer spectroscopy shows that a fraction of the Sb³⁺ is converted to Sb⁵⁺ and this fraction increases with x. High-field ¹¹B MAS NMR gives well-resolved resonances from boron atoms which are 3- and 4-coordinated to oxygen. The fraction of 4-coordinated boron, N₄, goes through a maximum value of 0.12±0.01 at x=0.5. The position of the maximum in N₄ is consistent with the cation potential for Sb³⁺, as observed for other systems. However, the low value of N₄ at this maximum is not so readily explained. The values are similar to those predicted if [BO₄]⁻ were stabilised by [SbO₄]⁺ but the trends with composition are different.     

Dramatic reduction in dark current of β-Ga2O3 ultraviolet photodectors via β-(Al0.25Ga0.75)2O3 surface passivation

Solar-blind ultraviolet photodetectors with metal-semiconductor-metal structure were fabricated based on β -(Al_0.25Ga_0.75)₂O₃/β -Ga₂O₃ film grown by metal-organic chemical vapor deposition. It was known that various surface states increase dark current and a large number of defects can hinder the transport of carriers, resulting in low switching ratio and low responsivity of the device. In this work, β -(Al_0.25Ga_0.75)₂O₃ films are used as surface passivation materials. Owning to its wide band gap, we obtain excellent light transmission and high lattice matching with β -Ga₂O₃. We explore the change and mechanism of the detection performance of the β -Ga₂O₃ detector after β -(Al_0.25Ga_0.75)₂O₃ surface passivation. It is found that under the illumination with 254 nm light at bias 5 V, the β -(Al_0.25Ga_0.75)₂O₃/β -Ga₂O₃ photodetectors show dark current of just 18 pA and high current on/off ratio of 2.16×10⁵. The dark current is sharply reduced about 50 times after passivation of the β -Ga₂O₃ surface, and current on/off ratio increases by approximately 2 times. It is obvious that β -Ga₂O₃ detectors with β -(Al_0.25Ga_0.75)₂O₃ surface passivation can offer superior detector performance.     

Self-assembly of β-Ga2O3 nanobelts

Self-assembly of β-Ga₂O₃ (beta-gallium oxide) nanobelts with diameters of 50–100 nm and lengths of tens to hundreds of microns have been studied using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). Under appropriate conditions such as nanobelts concentration, controlled solvent evaporation, β-Ga₂O₃ nanobelts assemble into a fan-like structure on the substrate. A tendency of these nanobelts to align parallel to each other was also observed. The mechanism behind the formation of self-assembly of β-Ga₂O₃ nanobelts has been proposed on the basis of lateral capillary forces.     

The role of Bi2O3 as a network modifier and a network former in xBi2O3 · (1 − x)LiBO2 glass system

The effect of Bi₂O₃ on the glass transition temperature, electrical conductivity and structure of LiBO₂ glass has been investigated. T_g vs. composition curve shows three different linear regions, while there is an overall decrease in T_g with the increase in Bi₂O₃ content. The slope of these three straight lines is in a decreasing order. These results are interpreted in terms of the increase in the number of non-bridging oxygen atoms, substitution of Bi-O bond in place of B-O bond and change in Li⁺ ion concentration. The conductivity vs. composition curve exhibits two maxima which are interpreted in terms of the structural modification effect of Bi₂O₃ on LiBO₂ network and mixed-former effect, respectively. Results obtained from the XPS studies of the samples of composition x 0.005, have shown that the number of non-bridging oxygen atoms from B-O bond increases with the increase in Bi₂O₃ content. It has a maximum value at x = 0.003 where the conductivity has also exhibited a maximum value. Further increase of Bi₂O₃ content causes decrease in it. For higher Bi₂O₃ content (x * > 0.005), O 1s spectra of Bi₂O₃ has been separated out from that of Bi₂O₃. Bismuth ions have been substituted for boron ions as network former ions.     

碱金属阳离子对[B3O7]型非线性光学晶体结晶习性的影响

本文利用高温拉曼光谱技术和从头计算的方法, 研究了LiB₃O₅和CsB₃O₅晶体高温熔融体的结构, 分析了碱金属阳离子对熔体结构的影响, 以及熔体结构的差异与LiB₃O₅和CsB₃O₅晶体结晶习性的联系. 结果表明: LiB₃O₅和CsB₃O₅晶体高温熔融体中的结构基团 主要为B₃Ø₇和B₃Ø₆两种不同类型的硼氧六元环; 环内BØ₄ 四面体的数量影响了六元环呼吸振动峰的拉曼频率, 随BØ₄四面体数量的增加六元环呼吸振动峰向低频移动; LiB₃O₅晶体高温熔融体中, BØ₄四面体含量相对较多; 然而, 离子半径相对较大的Cs⁺离子却阻碍了熔体中BØ₄四面体的形成, 造成CsB₃O₅晶体高温熔融体中BØ₄/BØ₃比值的降低. 结合LiB₃O₅和CsB₃O₅晶体生长动力学过程的分析 (Wang D, Wan S M et al. 2011 Cryst. Eng. Comm. 13 5239), 阳离子的不同导致高温熔体中BØ₄四面体数量的差异, 被认为是影响LiB₃O₅和CsB₃O₅晶体结晶习性的重要因素, 有效降低高温熔体中BØ₄四面体的数量, 将是实现LiB₃O₅晶体生长的关键条件. 关键词： 硼酸盐晶体 熔体结构 拉曼光谱 结晶习性     

Performance and reliability improvement of La_2O_3/Al_2O_3 nanolaminates using ultraviolet ozone post treatment

La-based binary or ternary compounds have recently attracted a great deal of attention as a potential candidate to replace the currently used Hf-based dielectrics in future transistor and capacitor devices for sub-22 generation. However, the hygroscopic nature of La₂O₃ hampers its application as dielectrics in electron devices. To cope with this challenge, ultraviolet (UV) ozone post treatment is proposed to suppress the moisture absorption in the H₂O-based atomic layer deposition (ALD) La₂O₃/Al₂O₃ nanolaminates which is related to the residual hydroxyl/hydrogen groups after annealing. The x-ray photoelectron spectroscopy (XPS) and conductive atomic force microscopy (AFM) results indicate that the moisture absorption of the H₂O-based ALD La₂O₃/Al₂O₃ nanolaminates is efficiently suppressed after 600 ℃ annealing, and the electrical characteristics are greatly improved.     

氧化铟/聚(3,4-乙烯二氧噻吩)复合材料的微结构及其热电性能研究

通过化学氧化合成的方法将纳米In_2O_3复合到聚(3,4-乙烯二氧噻吩)(PEDOT)中得到In_2O_3/PEDOT复合材料.利用X射线衍射、红外光谱、电子显微镜及正电子湮没等方法对复合材料的微观结构进行了系统研究,同时对材料的热学和电学性能进行了表征.结果表明,当In_2O_3的含量在22 wt%以下时,In_2O_3能很好地分散到PEDOT基体中.热电性能测试则显示In_2O_3/PEDOT复合材料的导电率随In_2O_3含量增加明显增大.纯PEDOT的电导率仅为7.5 S/m,而含12.3 wt%In_2O_3的复合材料的电导率达到25.75 S/m.该复合材料相应的功率因子(68.8×10~(-4)μW/m·K~2)相对于纯的PEDOT(14.5×10~(-4)μW/m·K~2)提高了近4倍.另外,复合材料的热导率相对于纯PEDOT也有所降低.最终复合材料的热电优值由0.015×10~(-4)提高到了0.073×10~(-4).结果表明,In_2O_3/PEDOT复合材料的热电性能相对于纯PEDOT的热电性能得到了比较明显的提高.     

Theoretical study of novel B–C–O compounds with non-diamond isoelectronic

Two novel non-isoelectronic with diamond(non-IED)B–C–O phases(tI16-B₈C₆O₂and mP16-B₈C₅O₃)have been unmasked.The research of the phonon scattering spectra and the independent elastic constants under ambient pressure(AP)and high pressure(HP)proves the stability of these non-IED B–C–O phases.Respective to the common compounds,the research of the formation enthalpies and the relationship with pressure of all non-IED B–C–O phases suggests that HP technology performed in the diamond anvil cell(DAC)or large volume press(LVP)is an important technology for synthesis.Both tI16-B₈C₆O₂and tI12-B₆C₄O₂possess electrical conductivity.mP16-B₈C₅O₃is a small bandgap semiconductor with a 0.530 eV gap.For aP13-B₆C₂O₅,mC20-B₂CO₂and tI18-B₄CO₄are all large gap semiconductors with gaps of 5.643 eV,6.113 eV,and 7.105 eV,respectively.The study on the relationship between band gap values and pressure of these six non-IED B–C–O phases states that tI16-B₈C₆O₂and tI12-B₆C₄O₂maintain electrical conductivity,mC20-B₂CO₂and tI18-B₄CO₄have good bandgap stability and are less affected by pressure.The stress-strain simulation reveals that the max strain and stress of 0.4 GPa and 141.9 GPa respectively,can be sustained by tI16-B₈C₆O₂.Studies on their mechanical properties shows that they all possess elasticity moduli and hard character.And pressure has an obvious effect on their mechanical properties,therein toughness of tI12-B₆C₄O₂,aP13-B₆C₂O₅,mC20-B₂CO₂and tI18-B4CO4 all increases,and hardness of mP16-B₈C₅O₃continue to strengthen during the compression.With abundant hardness characteristics and tunable band gaps,extensive attention will be focused on the scientific research of non-IED B–C–O compounds.     

First-principles study of electronic structure and magnetic properties of SrTi1−xMxO3 (M= Cr,Mn, Fe,Co, or Ni)

We used first-principles calculations to conduct a comparative study of the structure and the electronic and magnetic properties of SrTiO₃ doped with a transition metal (TM), namely, Cr, Mn, Fe, Co, or Ni. The calculated formation energies indicate that compared with Sr, Ti can be substituted more easily by the TM ions. The band structures show that SrTi_0.875Cr_0.125O₃ and SrTi_0.875Co_0.125O₃ are half metals, SrTi_0.875Fe_0.125O₃ is a metal, and SrTi_0.875Mn_0.125O₃ is a semiconductor. The 3d TM-doped SrTiO₃ exhibits various magnetic properties, ranging from ferromagnetism (Cr-, Fe-, and Co-doped SrTiO₃) to antiferromagnetism (Mn-doped SrTiO₃) and nonmagnetism (Ni-doped SrTiO₃). The total magnetic moments are 4.0_μB, 6.23_μB, and 2.0_μB for SrTi_0.75Cr_0.25O₃, SrTi_0.75Fe_0.25O₃, and SrTi_0.75Co_0.25O₃, respectively. Room-temperature ferromagnetism can be expected in Cr-, Fe-, and Co-doped SrTiO₃, which agrees with the experimental observations. The electronic structure calculations show that the spin polarizations of the 3d states of the TM atoms are responsible for the ferromagnetism in these compounds. The magnetism of TM-doped SrTiO₃ is explained by the hybridization between the TM-3d states and the O-2p states.     

X-ray diffraction studies of epitaxy in orthorhombic- DyMnO3/Er1Ba2Cu3O7-δ thin film heterostructures on LaAlO3 (100) substrates

The heteroepitaxy in DyMnO₃/Er₁Ba₂Cu₃O_7-δ bilayer thin films on LaAlO₃ (100) substates was characterized by four-circle X-ray diffractometry. The Er₁Ba₂Cu₃O_7-δ thin films on LaAlO₃ (100) substrates were prepared by molecular-beam deposition (MBD) and post-growth annealing in wet and dry O₂ at 880°C, whereas the DyMnO₃ thin films on the Er₁Ba₂Cu₃O_7-δ/LaAlO₃ (100) heterostructure were deposited by MBD and post-growth annealing in dry O₂ at 750°C. The conventional X-ray diffraction (XRD) patterns as well as pole figures (φ-scans) for specific (hkl) reflections were acquired. The Er₁Ba₂Cu₃O_7-δ thin film in the DyMnO₃/Er₁Ba₂Cu₃O_7-δ/LaAlO₃ (100) heterostructure showed [001] oriented epitaxial growth, as expected. The DyMnO₃ thin film on the Er₁Ba₂Cu₃O_7-δ epilayer in the heterostructure grew with (110) epitaxy in its metastable orthorhombic phase (lattice constants: a_o=5.272 Å, b_o=5.795 Å and c_o=7.38 Å). The heteroepitaxial relationships at the orthorhombic-DyMnO O₃ (110) /Er₁Ba₂Cu₃O_7-δ (001) interface was determined as the following: DyMnO₃ (110) Er₁Ba₂Cu₃O_7-δ (001), DyMnO₃ [1 0] ¶r; Er₁Ba₂Cu₃O_7-δ[100] or Er₁Ba₂Cu₃O_7-δ[010], and DyMnO₃ [001] ¶r; Er₁Ba₂Cu₃O _7-δ[010] or Er₁Ba₂Cu₃O_7-δ [100].     

n(Zn)：n(Ga)比值对合成ZnGa2O4结构及光致发光性能的影响

以ZnO和HGaO₂为原料,用不同配比合成出系列ZnGa₂O₄,并对其晶体结构和发光性能进行了研究。用荧光分光光度计检测了ZnGa₂O₄的激发和发射光谱,用X射线衍射仪检测了ZnGa₂O₄的衍射图谱,用热重差热仪绘制了TGA-DAT曲线。对检测结果分析认为:1.ZnGa₂O₄属于尖晶石结构,稍过量的Zn或Ga能进入ZnGa₂O₄结构中,并对ZnGa₂O₄的晶格常数产生一定影响。2.ZnGa₂O₄存在两个自激发光中心,当Ga稍过量时,自激发光中心是四面体镓氧键[T_d(Ga-O)],最大激发波长约248nm,最大发射波长约367nm;当Zn稍过量时,自激发光中心是八面体镓氧键[O_h(Ga-O)],最大激发波长约270nm,最大发射波长约441nm。当n(Zn):n(Ga)在理论值附近,激发和发射光强度最大,而且光谱峰位发生了红移。3.ZnGa₂O₄的热稳定性能非常好。上述结论对研究ZnGa₂O₄基质或掺杂的发光材料具有一定意义。     

Structure and optical properties of sol–gel derived Gd2O3 waveguide films

Pure and rare earth doped gadolinium oxide (Gd₂O₃) waveguide films were prepared by a simple sol–gel process and dip-coating method. Gd₂O₃ was successfully synthesized by hydrolysis of gadolinium acetate. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study the thermal chemistry properties of dried gel. Structure of Gd₂O₃ films annealed at different temperature ranging from 400 to 750 °C were investigated by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that Gd₂O₃ starts crystallizing at about 400 °C and the crystallite size increases with annealing temperature. Oriented growth of (4 0 0) face of Gd₂O₃ has been observed when the films were deposited on (1 0 0) Si substrate and annealed at 750 °C. The laser beam (λ=632.8 nm) was coupled into the film by a prism coupler and propagation loss of the film measured by scattering-detection method is about 2 dB/cm. Luminescence properties of europium ions doped films were measured and are discussed.     

γ射线辐照对含钆磷酸钡玻璃影响的光谱分析

为研制新型γ射线屏蔽材料,采用熔融淬火法制备了xGd₂O₃-(50-x)BaO-50P₂O₅（0≤x≤7 mol%）系列玻璃样品,并经60Co辐照源辐照,利用UV-Vis-NIR,Raman等分析技术研究了玻璃的光学特性和微观结构。结果表明,玻璃在γ射线辐照下产生了磷氧空穴中心（Ⅰ类色心）,呈现棕色;Gd₂O₃能增强磷酸钡玻璃的抗γ辐照能力,玻璃中Gd₂O₃含量越高,γ射线辐照导致的色心数量越少;玻璃产生的色心数量会随着γ射线辐照剂量的增大而增加;Gd₂O₃加入降低了玻璃对可见光和近红外光的透过率;γ射线辐照使玻璃出现了光学吸收带损耗,玻璃在紫外到可见光区的透过率降低;玻璃样品的主要结构为Q2偏磷酸盐结构,伴有少量Q1焦磷酸盐和Q0正磷酸盐结构;玻璃微观网络结构在γ射线辐照下变化不明显。     

γ-Fe_2O_3/NiO核-壳纳米花的合成、微结构与磁性

利用溶剂热/热分解的方法合成出微结构可控的γ-Fe_2O_3/NiO核-壳结构纳米花.分析表明NiO壳层是由单晶结构的纳米片构成,这些纳米片不规则地镶嵌在γ-Fe_2O_3核心的表面.Fe3O4/Ni(OH)_2前驱体的煅烧时间对γ-Fe_2O_3/NiO核-壳体系的晶粒生长、NiO相含量和壳层致密度均有很大的影响.振动样品磁强计和超导量子干涉仪的测试分析表明,尺寸效应、NiO相含量和铁磁-反铁磁界面耦合效应是决定γ-Fe_2O_3/NiO核-壳纳米花磁性能的重要因素.随着NiO相含量的增加,磁化强度减小,矫顽力增大.在5 K下,γ-Fe_2O_3/NiO核-壳纳米花表现出一定的交换偏置效应(H_E=46 Oe),这来自于(亚)铁磁性γ-Fe_2O_3和反铁磁性NiO之间的耦合相互作用.与此同时,这种交换耦合效应也进一步提高了样品的矫顽力(H_C=288 Oe).     

新系列超导相TlBaCan-1CunO2n+2.5(n=2,3)的晶体结构和超导电性

本文用粉末烧结法合成了Tl-Ba-Ca-Cu-O体系TlBa₂Ca_n-1Cu_nO_2n+2.5新系列超导相,用粉末衍射法测定了n=2和3的晶体结构,属简单四方单胞,空间群为D_4h¹-P4/mmm,点阵常数a相同,而c值不同,随n值而增大。a=3.847?,c分别为12.73?和15.89?,每单胞含一个化合式单位,阳离子沿四方晶系的(0,0,z)和(1/2,1/2,z)位置交替排列,排列的顺序相同,n=3比n=2依次多增加Ca和Cu及相应的氧离子。TlBa₂Ca_nCu_nO_2n+2.5,n=3时,零电阻超导转变温度T_c(0)=112K;n=2时,T_c(0)=101K,与Tl₂Ba₂Ca_n-1Cu_nO_2n+4型体心四方晶胞超导相不同,TlBa₂Ca_n-1Ca_nO_2n+2.5结构中缺氧类钙钛矿型结构单元[Ba₂Ca_n-1Cu_nO_2n+1]仅被TI-O单层所隔开,当n相同时,Tl-O双隔层的体心四方单胞比Tl-O单层的简单四方单胞的超导转变温度高10K左右,这说明Tl-Ba-Ca-Cu-O体系中超导相的转变温度不仅与类钙钛矿结构单元的[CuO₄]和[CuO₅]的数目有关,而且与Tl-O的隔层数目有关。 关键词：     

Observation of giant magnetocaloric effect under low magnetic fields in EuTi_(1-x)Co_xO_3

The magnetic properties and magnetocaloric effect(MCE) in EuTi_(1-x)Co_xO_3(x = 0, 0.025, 0.05, 0.075, 0.1) compounds have been investigated. When the Ti~(4+) ions were substituted by Co2+ions, the delicate balance was changed between antiferromagnetic(AFM) and ferromagnetic(FM) phases in the EuTiO_3 compound. In EuTi_(1-x)Co_xO_3 system, a giant reversible MCE and large refrigerant capacity(RC) were observed without hysteresis. The values of -?S_M~(max) were evaluated to be around 10 J·kg~(-1)·K~(-1) for EuTi_(0.95)Co_(0.05)O_3 under a magnetic field change of 10 kOe. The giant reversible MCE and large RC suggests that EuTi_(1-x)Co_xO_3 series could be considered as good candidate materials for low-temperature and low-field magnetic refrigerant.     

Surface termination, composition and reconstruction of Fe3O4(001) and γ-Fe2O3(001)

We address a current controversy concerning the nature of the surfaces of Fe₃O₄(001) and γ-Fe₂O₃(001) grown on MgO(001) by molecular beam epitaxy. Despite recent claims to the contrary, we show that γ-Fe₂O₃(001) unambiguously exhibits a (1×1) surface net, in contrast to Fe₃O₄(001), which assumes a R45 reconstruction. In addition, we present high-energy-resolution Fe 2p and O 1s core-level photoelectron spectra obtained at both normal and grazing emission for γ-Fe₂O₃(001) and Fe₃O₄(001). These spectra show that the Fe₃O₄(001) surface has a higher Fe(III)/Fe(II) ratio than the bulk, and that the asymmetry in the O 1s line shape for Fe₃O₄(001) is due to final state effects rather than the presence of a surface oxygen or hydroxyl species.     

SnO2/Co3O4 nanofibers using double jets electrospinning as low operating temperature gas sensor

SnO₂/Co₃O₄nanofibers(NFs)are synthesized by using a homopolar electrospinning system with double jets of positive polarity electric fields.The morphology and structure of SnO₂/Co₃O₄hetero-nanofibers are characterized by using field emission scanning electron microscope(FE-SEM),transmission electron microscope(TEM),x-ray diffraction(XRD),and x-ray photoelectron spectrometer(XPS).The analyses of SnO₂/Co₃O₄NFs by EDS and HRTEM show that the cobalt and tin exist on one nanofiber,which is related to the homopolar electrospinning and the crystallization during sintering.As a typical n-type semiconductor,Sn O₂has the disadvantages of high optimal operating temperature and poor reproducibility.Comparing with Sn O₂,the optimal operating temperature of SnO₂/Co₃O₄NFs is reduced from 350℃to 250℃,which may be related to the catalysis of Co₂O₂.The response of SnO₂/Co₃O₄to 100-ppm ethanol at 250℃is 50.9,9 times higher than that of pure Sn O₂,which may be attributed to the p–n heterojunction between the n-type Sn O₂crystalline grain and the p-type Co₂O₂crystalline grain.The nanoscale p–n heterojunction promotes the electron migration and forms an interface barrier.The synergy effects between Sn O₂and Co₂O₂,the crystalline grain p–n heterojunction,the existence of nanofibers and the large specific surface area all jointly contribute to the improved gas sensing performance.