高平均功率面阵二极管激光器散热分析

 采用三维有限元法分析了面阵二极管激光器背冷式封装结构的散热效率,对次热沉厚度,冷却器结构参数进行了优化设计,计算结果表明,优化设计后的封装结构,可满足面功率密度为500W/cm²,占空比为20％的高平均功率面阵二极管激光器的散热要求。     

激光二极管高效铜微通道冷却器设计

 通过对铜微通道冷却器的散热分析，设计出５层结构的模块式铜微通道冷却器。采用常规的线切割工艺加工，散热通道宽大约200μm，深300μm，各层间用真空钎焊的方法组装。该冷却器对于腔长06mm、宽10mm的线阵激光二极管芯片热阻为0.58℃/W。通过面阵激光二极管封装实验证明，该冷却器可用于10％占空比工作的面阵激光二极管封装。     

高密度封装二极管激光器阵列

 理论模拟了自制的高效冷却器的散热能力,分析了单元封装结构所需材料的导热特性,获得了高功率二极管激光器在高功率密度、高占空比条件下运行的可行性。改进了高密度封装的关键工艺,热沉金属化层达到了3~5 mm,焊料厚度为4~7 mm,封装间距0.6 mm,采用峰值功率1 kW的背冷式叠阵二极管激光器。实验测试结果表明:封装的二极管激光器叠阵单元的整体封装热阻为0.115 ℃/W,有良好的散热能力;该叠阵模块在电流为100 A、占空比15%时,输出峰值功率为986 W,峰值功率密度达到1.5 kW/cm2,平均每个板条的斜效率为1.25 W/A,激光器阈值电流为20 A左右。     

高功率二极管激光器相变冷却技术

根据高功率二极管激光器的散热需求,设计了一种储能式相变冷却实验系统,并开展了喷雾相变冷却器和微通道相变冷却器的设计。采用多孔微结构的换热表面,用氨做制冷剂,实现了喷雾相变冷却器表面温度37 ℃时,散热功率密度达到了511 W/cm2。采用节流汽化原理,分别设计了背冷式相变微通道冷却器和薄片型的模块式相变微通道冷却器,背冷式相变微通道冷却器采用氨做制冷剂, 散热功率密度达到了550 W/cm2,采用R124做制冷剂,散热功率密度约270 W/cm2。采用R124做制冷剂,实现了脉冲激光功率3 kW和连续激光功率100 W的相变冷却二极管激光器模块封装。     

双波长高灵敏度Bragg光纤光栅压力传感器

裸光纤光栅压力灵敏度只有 -2. 05×10-6 /MPa,这样并不能将其用于低压力范围内的测量 本文改进了封装结构,利用金属管结构对光纤光栅部分封装,制作成双波长高灵敏度光纤光栅压力传感器 其压力灵敏度在 0~0. 44MPa的范围内可达-2. 44×10-3 /MPa,是裸光栅的 1200倍,大大提高了光纤光栅压力传感的灵敏度 采用自行研制的Bragg光纤光栅,其反射波长为 1558. 00 nm,峰值反射率为 99% 封装后的Bragg光纤光栅位于铜管的轴心,将其一部分 (约光纤光栅的二分之一 )封装到长 25mm,外径 10mm厚为 0. 8mm的铜管内 室温为 18℃时将封装好的光…     

基于偶联剂技术的光纤光栅压力传感实验研究

报道了利用偶联技术封装光纤光栅压力传感器的新方案.通过采用特殊聚合物材料将光纤光栅封装于金属管中，并采用偶联材料分别与聚合物和光纤以化学键偶联的工艺，解决了由于有机弹性体聚合物的弹性模量（1.2×105 N/m2）与光纤光栅的弹性模量(7×1010 N/m2)相差很大，在压强较大时易导致光纤光栅与聚合物材料之间的撕裂滑脱问题，改善了光纤光栅压力响应特性.封装后的光纤光栅压力的线性测量范围为0.04 MPa~0.6 MPa，压力响应灵敏度为－4.48 nm/MPa，与裸光栅压力响应灵敏度－0.003063 nm/MPa相比，增敏了1463倍.利用实验中所使用光谱仪0.05 nm的分辨率，压强测量准确度为±0.01 MPa，线性度为0.9978.     

不同覆盖度下丙硫醇在Au(111)面吸附的理论研究

采用基于密度泛函理论的第一性原理方法研究了丙烷硫醇 (C₃H₇SH)在Au(111)面五种覆盖度(1/16, 2/16, 3/16, 4/16, 1/3) 下的未解离和解离吸附的结构、能量和吸附性质. 发现丙烷硫醇的倾斜角和吸附能均受覆盖度影响, 计算结果显示丙烷硫醇的倾斜角随着覆盖度的增大减小了6°–10°, 吸附能随覆盖度的增大减小了0.21 eV. 特别针对饱和覆盖度, 研究了三种可能的表面结构: (2√3×2√3 ight)R30°, 2√3×3和(3×3). 发现S–H键未解离时三种表面结构的吸附构型和吸附能基本一致; S–H键解离后, (2√3×2√3 ight)R30°和2√3×3结构的吸附能比以(3×3)结构的吸附能约高0.05–0.07 eV, 说明C₃H₇S在Au(111)面吸附时, 倾向于形成(2√3×2√3 ight)R30°和2√3×3结构. 此外, 采用DFT-D2方法对饱和覆盖度下C₃H₇SH分子在Au(111)面的吸附进行了范德华修正, 结果显示分子间相互作用使吸附物和Au表面的距离减小, 该相互作用对吸附能的修正值为0.53 eV, 修正后结果与实验结果接近. 关键词： 第一性原理 覆盖度 表面结构 范德华力     

入射光参量对Ce∶KNSBN晶体中光扇效应的影响

采用非同时读出条件下晶体两波耦合实验装置,研究了入射光强度及光入射角对Ce∶KNSBN晶体中光扇效应的影响.结果表明,光扇效应存在明显的入射光强度阈值特性,入射光强度阈值为38.2 mW/cm2.对应相同的入射光强度,光入射角θ为15°时稳态光扇强度Ifsat最强,如:入射光强度为38.2 mW/cm2时,Ifsat最大为0.7 mW/cm2;入射光强度为57.3 mW/cm2时,Ifsat最大为1.8 mW/cm2.     

石墨烯封装单层二硫化钼的热稳定性研究

将单层二硫化钼用石墨烯进行封装,构造了石墨烯和二硫化钼的范德瓦耳斯异质结构,并且分别在氩气（Ar）和氢气（H₂）氛围下,详细研究了被封装的二硫化钼的热稳定性.结果表明：在氩气氛围中,石墨烯封装的二硫化钼在400–1000℃下一直保持稳定,而石墨烯和氧化硅上裸露的二硫化钼在1000℃时几乎全部分解;在氢气氛围中,石墨烯封装的二硫化钼在400–1000℃下一直稳定存在,而石墨烯和氧化硅上裸露的二硫化钼在800℃下已经完全分解.综上可得,在氩气和氢气的氛围下,被石墨烯封装的二硫化钼的热稳定性得到了显著的提高.该研究通过用石墨烯将单层的二硫化钼进行封装以提高其热稳定性,在未来以单层二硫化钼作为基础材料的电子器件中,可以保证其在高温下能够正常工作.该研究也为提高其他二维材料的热稳定性提供了一种可行的方法和思路.     

等离子MOCVD系统生长ZnO薄膜掺N2和掺NH3特性比较

利用MOCVD方法生长了高质量的ZnO薄膜材料,分别通过N2和NH3对c面和R面蓝宝石衬底上生长的ZnO薄膜材料进行了掺杂行为研究.掺N2时,X射线衍射半峰全宽仅为0.148°,室温光荧光发光峰位于3.29eV,半峰全宽～100meV,电阻率由0.65 Ω·cm增大到5×l04Ω·cm.掺NH3时,X射线衍射峰半峰全宽0.50°,样品为弱p型,电阻率为102Ω·cm,载流子浓度为1.69×1016 cm-3.同时我们还观察到弱p型材料很容易退化成n型高阻材料.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.