低压反应离子镀方法制备ITO透明导电膜

溅射镀膜方法是制备ITO透明导电膜最常用也是实验研究最多的方法。实验使用一种不同于溅射方法的另一种制备工艺—低压反应离子镀方法—制备ITO透明导电膜。实验对不同沉积速率和不同氧气流量对ITO透明导电膜的方块电阻以及光学透过率的影响进行了详细地分析,并综合比较得到了当沉积速率为0.5nm/s,氧气流量为24cm3/min时,在波长为550nm处,方块电阻为20Ω,λ=550nm透过率为90.8%的优质ITO透明导电膜。     

反应离子镀制备ITO膜

采用反应离子镀新工艺成功地在K9玻璃上制备了ITO(Indium Tin Oxide)透明导电膜,所制备的ITO膜在550～600nm波长范围内,典型的峰值透过率为89%,面电阻为34Ω/□。     

有ITO透明导电膜的平面分层介质系统的电磁波性能理论研究

理论研究了有ITO(indium tin oxide)透明导电膜的多层平面分层介质系统的电磁性能，给出的理论曲线和实测曲线符合很好.多层平面分层介质系统的电磁性能与ITO膜(方块电阻为8Ω)所在界面位置和平面分层介质系统层数及各层厚度等有关.优化设计了一种含有ITO透明导电膜的厚度仅7.35mm的四层平面分层介质系统，其在8—18GHz频段内电磁波反射性能很好.作为多层平面分层系统中的ITO导电膜，其方块电阻应低于30Ω，并且越小，其反射性能越好. 关键词： 多层平面介质系统 电磁性能 ITO透明导电膜     

格兰泰勒棱镜高性能宽带减反射膜的优化设计及性能测试

格兰泰勒棱镜在光学领域有着重要的应用,透过比的高低和有效带宽的大小,直接影响着棱镜的品质.为了提高棱镜的透射率,拓宽有效使用带宽,借助于计算机辅助设计方法,设计了高性能多层减反射膜系:选用合适的光学薄膜材料,利用电子束蒸镀,借助于离子源辅助蒸镀,制作了高性能的宽带减反射膜.测试结果表明:平均剩余反射率小于0.5%,有效使用带宽在可见光区大于100 nm,达到了设计要求,提升了棱镜的品质.     

超宽带减反射膜的设计和制备

设计了400～900 nm波段上的超宽带减反射膜,在410～850 nm范围内的平均残余反射率设计值约为0.2%,在设计的全波段上约为0.24%.讨论了初始膜系结构的选择原则,分析了带宽、膜层折射率差、最外层折射率和膜层总厚度等因素对宽带减反射特性的影响.对特定的带宽.增加两种薄膜材料的折射率差和选择尽可能低的最外层折射率对获得优良的减反射特性是非常重要的.实验制备了K9玻璃上TiO2/MgF2两种材料组成的8层结构的超宽带减反射膜,实测结果表明,在带宽520 nm范围内的平均残余反射率约为0.44%,说明用二种材料设计超宽带减反射膜是成功的,对垂直入射的减反射膜.多种材料的膜系并不比两种材料更具优越性.     

锗基底7～11.5μm高性能红外宽带减反射膜的研究

为了提高锗基底的透过率和膜层的机械强度，对锗基底上高性能的红外宽带减反射膜的设计与制备工艺进行了研究。介绍了红外宽带减反射膜的膜料选择、膜系设计以及采用 离子束辅助沉积该膜系的过程。给出了用该方法制备的7～11.5μm波段宽带减反射膜的实测光谱曲线，其峰值透过率高达99.5％以上，在设计波段范围内平均透过率大于97.5％， 膜层附着性能好，光机性能稳定。这对于红外光学系统的应用具有十分重要的意义。     

薄膜光学 制膜技术与装置

O484.12006010529低压反应离子镀方法制备ITO透明导电膜=Preparationof ITOfil ms by reactive lowvoltageion plating[刊,中]/徐颖(中科院长春光机所光学技术研究中心.吉林,长春(130022)),高劲松…∥光学技术.—2005,31(5).—669-671使用一种不同于溅射方法的另一种制备工艺—低压反应离子镀方法制备ITO透明导电膜。实验对不同沉积速率和不同氧气流量对ITO透明导电膜的方块电阻以及光学透过率的影响进行了详细的分析,并综合比较得到了当沉积速率为0.5nm/s,氧气流量为24cm3/min时,在波长为550nm处,方块电阻为20Ω,λ=550nm,透过率为90…     

膜层厚度对蓝宝石衬底上生长的ITO薄膜性质的影响

采用磁控溅射的方法在蓝宝石衬底上制备了氧化铟锡(ITO)透明氧化物薄膜;研究了不同厚度薄膜的结构、光学和电学特性。经X射线衍射(XRD)测量,发现在蓝宝石衬底上生长的ITO薄膜呈现了较高的(222)择优取向;随着膜层厚度的增加,该衍射峰对应的2θ衍射角逐渐向大角度方向移动,同时该衍射峰的半峰全宽逐渐减小,平均晶粒尺寸增大。 经光学透射光谱测量,发现随着膜层厚度的增加,光学透过率逐渐减小。膜层厚度为0.2 μm时,可见光透过率超过80%,当膜层厚度为0.8 μm时,可见光透过率下降到60%。电学测量结果表明,随着膜层厚度的增加,薄膜电阻率逐渐减小。膜层厚度为0.2 μm时,电阻率为9×10^-4 Ω·cm, 膜层厚度为0.8 μm时,电阻率为5.5×10^-4 Ω·cm。     

新型空间硅太阳电池纳米减反射膜系的优化设计

结合纳米材料折射率（小于1.4）和AM0太阳光谱特性,对空间硅太阳电池的减反射膜进行了设计分析.分别设计了常规材料和纳米材料的双层、三层减反射膜,得到了最佳的膜系参数,并作出了反射率变化曲线.结果发现,采用低折射率纳米材料的三层减反射膜有着更好的减反射效果,新型纳米减反射膜系与采用常规材料的减反射膜系相比,优化后的最小加权平均反射率减小了15%（双层减反射膜）和24.5%（三层减反射膜）. 关键词： 折射率 减反射膜 纳米材料 空间硅太阳电池     

近红外激光薄膜滤光片的研制

以双抛Si片为基底,采用离子束辅助热蒸发沉积技术研制了1.2～3μm波段激光薄膜滤光片.采用长波通滤光片与减反射膜相结合的薄膜样品设计方法,高、低折射率材料分别选用ZnS和MgF2,综合考虑光谱特性和电场强度分布,使用TFCale膜系软件设计出1.064μm高反、1.2～3μm波段增透的长波通滤光片.长波通膜系膜系结构为G|4H2L1.5H2L2H1.5L2H4L|A,减反射膜膜系结构为G|3.5H3.5L|A.最终实现1.2～3μm波段峰值透过率达98.48%,平均透过率为92.35%,1.064μm处透过率为5.09%的光谱特性.对薄膜样品分别采用离子束处理和退火处理,发现适当的工艺参数,有助于提高薄膜激光损伤阈值,当退火温度为250℃时,其激光损伤阈值可达6.3J/cm~2.本文研究可为近红外薄膜滤光片设计和制备提供参考.     

基于金属掺杂ITO透明导电层的紫外LED制备

为降低ITO薄膜对紫外波段的光吸收,制备低电压高功率的紫外LED,研究了一种基于金属掺杂ITO透明导电层的365 nm紫外LED的制备工艺。利用1 cm厚的石英片生长了不同厚度ITO薄膜以及在ITO上掺杂不同金属的新型薄膜,并研究了在不同的退火条件下这种薄膜的电阻和透过率,分析了掺杂金属ITO薄膜的带隙变化。将这种掺杂的ITO薄膜生长在365 nm外延片上并完成电极生长,制备成14 mil×28 mil的正装LED芯片。利用电致发光（EL）设备对LED光电性能进行测试并对比。实验结果表明:掺Al金属的ITO薄膜能够相对ITO薄膜的带隙提高0.15 eV。在600℃退火后,方块电阻降低6.2 Ω/□,透过率在356 nm处达到90.8%。在120 mA注入电流下,365 nm LED的电压降低0.3 V,功率提高14.7%。ITO薄膜掺金属能够影响薄膜带隙,改变紫光LED光电性能。     

Optical characteristics of light-emitting diodes with high transparent conductive film at low temperatures

In this paper, we report the synthesis and transmittance of a titanium–indium–tin oxide (TITO) film, fabricated through a low-temperature process. The TITO film was fabricated by incorporating a 2-nm-thick titanium barrier at the bottom of an ITO film. The transmittance characteristics of the TITO film were examined for light-emitting diodes (LEDs) of various wavelengths at different post-annealing temperatures. A saturated high transmittance was observed at a temperature of 550 °C, which is relatively low when compared to that in the case of a conventional ITO film. Photoluminescence studies demonstrated that a 450-nm-thick TITO film, fabricated at 550 °C, was highly effective in improving the performance of the LED, when compared to conventional ITO films. The X-ray diffraction peaks, scanning electron microscopy images, and transmittance electron microscopy images confirmed that titanium atoms could improve the crystallization of ITO. It was found that non-crystallization in ITO was effectively activated by the titanium barrier. Furthermore, the optical bandgap (3.77 eV for the conventional ITO film) was improved to 3.92 eV in the TITO film. An infrared LED fabricated with a TITO film displayed 70% higher light output power than that with a conventional ITO film. These results suggest that using a titanium barrier is essential to effectively improve inactive nucleation sites in ITO films grown at low temperatures.     

两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

Enhancing indium tin oxide (ITO) thin film adhesiveness using the coupling agent silane

The coupling agent γ-mercapto propyl trimethoxy silane (WD-80) was used to enhance the adhesiveness of the indium tin oxide (ITO) thin film, which was prepared on a glass substrate using the sol-gel method. The nano-scratching test, XRD, TEM, SEM, and UV-vis spectrophotometer were employed to examine film adhesion, crystal structure, surface morphology, and transmittance. The results indicated that silane coupling agent, used in low concentration, did not change the film structure but increased the critical load of the film by 49%, from 4.16 mN to 6.20 mN, when the film was peeled off from the substrate. The principle by which the coupling agent works is discussed. In addition to increasing with the light wavelength, the average transmittance of the film in the visible range varied from 78.9% to 83.6%. Moreover, as a function of the WD-80 silane coupling agent, the film exhibited a high smoothness and density due to the orderly arrangement of particles.     

射频溅射功率对AZO薄膜结构及光电特性和热稳定性的影响

采用射频磁控溅射法,在玻璃基片上制备了ZnO:Al(AZO)透明导电薄膜。用X射线衍射(XRD)仪、紫外-可见分光光度计、方块电阻测试仪和台阶仪对不同溅射功率下Al掺杂ZnO薄膜的结晶、光学、电学性能、沉积速率以及热稳定性进行了研究。研究结果表明:不同溅射功率下沉积的AZO薄膜具有六角纤锌矿结构,均呈c轴择优取向;(002)衍射峰强和薄膜的结晶度随溅射功率的提高逐渐增强;随溅射功率的提高,AZO薄膜的透射率有所下降,但在可见光(380～780nm)范围内平均透射率仍80%;薄膜的方块电阻随溅射功率的增加逐渐减小;功率为160～200W时,薄膜的热稳定性最好,升温前后方块电阻变化率为13%。     

Annealing induced refinement on optical transmission and electrical resistivity of indium tin oxide

The effect of annealing condition on sputtered indium tin oxide （ITO） films on quartz with the thickness of 200 nm is characterized to show enhanced optical transparency and optimized electrical contact resistivity. The as-deposited grown ITO film exhibits only 65% and 80% transmittance at 532 and 632.8 nm, respectively. After annealing at 475 ℃ for 15 min, the ITO film is refined to show improved transmittance at shorter wavelength region. The transmittances of 88.1% at 532 nm and 90.4% at 632.8 nm can be obtained. The 325-nm transmittance of the post-annealed ITO film is greatly increased from 12.7% to 41.9%. Optimized electrical property can be obtained when annealing below 450 ℃, leading to a minimum sheet resistance of 26 Ω/square. Such an ITO film with enhanced ultraviolet （UV） transmittance has become an alternative candidate for applications in current UV photonic devices. The morphology and conductance of the as-deposited and annealed ITO films are determined by using an atomic force microscopy （AFM）, showing a great change on the uniformity distribution with finite improvement on the surface conductance of the ITO film after annealing.     

后退火处理对铟锡氧化物表面等离激元共振特性的影响

近年来,表面等离激元光子学发展迅速,并取得了众多新成果.重掺杂半导体材料的表面等离激元共振性质的研究,也得到了人们越来越多的关注.本文通过纳米球刻印技术制备准三维二氧化硅纳米球阵列,在阵列上沉积铟锡氧化物薄膜,通过不同条件下的后退火处理改变铟锡氧化物薄膜的载流子浓度和载流子迁移率,并研究随着材料性质的改变其相应表面等离激元共振特性的变化规律.结果表明：退火处理均使铟锡氧化物薄膜的晶粒长大,光学透过率增加;在空气中退火会导致铟锡氧化物薄膜的载流子浓度减少,其表面等离激元共振峰红移;而真空退火则使铟锡氧化物薄膜的载流子浓度增加,共振峰蓝移.这些研究结果可为后续铟锡氧化物表面等离激元材料及器件的研究提供科学依据和实际指导.     

Characteraction of Ag-doped ZnO thin film synthesized by sol–gel method and its using in thin film solar cells

Pure 2% and 4% Ag-doped ZnO thin films have been synthesized on glass substrates by sol–gel method. The structure, morphology and optical properties of the samples have been studied by X-ray diffractometer (XRD), scanning probe microscope, UV–vis spectrophotometer, respectively. The XRD result shows that the pure ZnO has a wurtzite hexagonal structure, no phase segregation is observed. The surface morphology of pure ZnO thin film shows that the grains are growing preferentially along the c-axis orientation perpendicular to the substrates. The transmittance spectra reveal that all samples have high transmittance above 90% in visible region. With Ag doping content increase, a red shift is observed. The performance of Ag-doped ZnO films using in thin film solar cells are simulated. The results show that 4% Ag-doped ZnO thin film can greatly improve the absorption of the cells. Compare to pure ZnO, solar cell's energy conversion efficiency improvement of 2.47% is obtained with 4% Ag doped ZnO thin film.     

ZnO-SnO_2透明导电薄膜的制备及性能研究

采用二步成胶工艺制备ZnO-SnO_2透明导电薄膜,应用X射线衍射、原子力显微镜、紫外-可见分光光度计、薄膜分析仪及四探针仪等对薄膜的结构、表面微观形貌、透过率和导电性能进行表征.结果表明,锌锡摩尔比为9/12,退火温度为500 ℃时,薄膜的透过率达90%,电阻率为3.15×10~(-3) Ω·cm.与其它工艺相比,二步成胶工艺所制备出的ZnO-SnO_2透明导电薄膜性能优异.