基于倾斜光栅的可调谐线偏振掺镱光纤激光器

提出了一种基于45°倾斜光纤光栅和光纤布拉格光栅的线性腔结构的可调谐线偏振掺镱光纤激光器。利用45°倾斜光纤光栅作为起偏器件实现了中心波长为1065.90 nm、3 dB带宽为0.03 nm、偏振消光比高于35 dB的线偏振激光输出,输出激光的偏振消光比在4 h内稳定性良好。基于光纤布拉格光栅反射波长的温度特性实现了中心波长在1065.92～1066.87 nm范围内的连续可调,在波长可调谐状态下输出激光的偏振消光比保持在30 dB以上。     

大功率多波长可转换双包层光纤激光器

在多模掺镱双包层光纤上,利用相位掩模法直接写制Bragg光栅作为激光器后腔镜,得到多波长激光输出.在室温下,通过调节偏振控制器可以得到稳定的单波长及多波长的激光输出,输出波长范围在1 056～1 061 nm,线宽均小于0.02 nm.在25 W的976 nm激光泵浦下,激光器得到功率为6 W的多波长输出.     

基于偏振保持掺Er3+光纤的高稳定性单波长光纤激光器

研制出光敏偏振保持掺Er³⁺光纤,通过在这种光纤上紫外写入三个光纤光栅,形成对抽运激光高转化效率的谐振腔.在输出功率为23.617dBm、工作波长为976nm的激光抽运下,得到均值功率为9.20dBm、均值中心波长为1554.554nm的单波长激光输出.在室温下800min（约13.3h）的测量时间内,其输出功率的波动为±0.05dB,中心工作波长的波动为±0.0015nm. 关键词： 光纤激光器 3+光纤')" href="#">偏振保持掺Er³⁺光纤 光纤Bragg光栅     

应力所致单偏振相移分布反馈光纤激光器

利用对相移分布反馈（DFB）光纤激光器的相移区施加一定的应力，使光栅的相移区产生双折射，得到了消光比为14dB的运行在1053nm的单偏振激光输出，并且由于光纤光栅的相移区偏离了光纤光栅的中心位置，使激光器的输出功率特性具有一定的方向选择性。     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法，在D形内包层掺Yb3+双包层光纤一端直接写制出Bragg光栅，用作双包层光纤激光器的输出腔镜.试验得到了线宽为0.196nm，波长为1058.2nm，最高输出功率为570mW的稳定激光输出，解决了激光器中模式竞争造成的输出不稳定现象.从速率方程出发，对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析，结果与实验符合很好. 关键词： 双包层光纤光栅 掺Yb3＋双包层光纤激光器 相位掩模 速率方程     

镀膜长周期光纤光栅的单峰宽带滤波特性

镀膜长周期光纤光栅(LPFG)工作于相位匹配转折点时纤芯模与高次包层模的耦合产生单个宽带损耗峰,其3 dB带宽取决于纤芯模和包层模之间的色散差、光栅长度以及中心波长.研究表明,薄膜折射率和厚度的变化将影响纤芯模与包层模之间的色散差,从而影响损耗峰的3 dB带宽,同时损耗峰中心波长亦随之移动.薄膜折射率为1.57,厚度为350 nm时,损耗峰带宽可达302 nm.减小光栅长度在保证中心波长损耗大于6 dB的前提下可使损耗峰3 dB带宽增大至334 nm.进一步研究表明,在均匀LPFG中偏离光栅中点的适当位置引入单个π相移可以使带宽增大至372 nm以上.     

双面曝光长周期光纤光栅偏振相关损耗

研究了采用高频CO2激光脉冲通过单面和双面曝光制作出的长周期光纤光栅(LPFG)的偏振相关损耗特性。单面曝光制作的长周期光纤光栅由于光纤横截面折射率改变不均匀,对入射光偏振态有较强的依赖性,主要表现为偏振相关损耗较大;为了降低偏振相关损耗,在制作长周期光纤光栅的过程中采用双面曝光的方法,以使其横截面折射率调制受高频CO2激光曝光改变均匀。实验数据显示,高频CO2激光脉冲制作的普通单面曝光长周期光纤光栅最大偏振相关损耗高达1.24 dB,而采用双面曝光的相同谐振峰值长周期光纤光栅的偏振相关损耗则可降至0.42 dB。因此,双面曝光制作的长周期光纤光栅能较好地克服入射光偏振态的不良影响,从而满足对偏振敏感的光纤通信和传感系统的应用要求。     

光纤光栅选频掺Yb3+双包层光纤激光器

利用相位掩模法 ,在D形内包层掺Yb3 双包层光纤一端直接写制出Bragg光栅 ,用作双包层光纤激光器的输出腔镜 .试验得到了线宽为 0 196nm ,波长为 10 5 8 2nm ,最高输出功率为 5 70mW的稳定激光输出 ,解决了激光器中模式竞争造成的输出不稳定现象 .从速率方程出发 ,对激光器的输出功率与抽运功率、光栅反射率的关系以及最佳光纤长度进行了理论分析 ,结果与实验符合很好     

波长无啁啾调谐窄线宽掺Yb3+双包层光纤激光器

用相位掩模法, 在圆形掺Yb3+双包层光纤上制作了Bragg光纤光栅,并用它作为双包层光纤激光器的输出腔镜, 在光栅反射中心波长1055.2 nm位置得到了窄线宽的激光输出, FWHM为0.271 nm, 信噪比约为40 dB.这种结构的双包层光纤激光器, 在双包层增益光纤和后腔镜间没有连接损耗, 减小了双包层光纤激光器体积. 用自行制作的等强度梁对作为输出腔镜的光纤光栅做双向应力调谐, 实现了激光波长无啁啾调谐输出, 调谐范围1051.1~1060.04nm,调谐量达8.9nm, 调谐过程中激光3 dB线宽基本无变化.     

利用倾斜光纤光栅的可开关双波长光纤激光器

报导了一种在四波混频作用下利用倾斜光纤布拉格光栅进行波长选择的可开关双波长掺铒光纤激光器。通过将倾斜光纤光栅与单模光纤进行横向错位焊接,使光栅的反向LP01和LP11两个模式具有相近的有效反射率,从而可以用来进行激光器的双波长选择。接入腔内的一段高非线性光子晶体光纤引入的四波混频效应克服了模式竞争,使得双波长激光在室温下稳定振荡。腔内起偏器和偏振控制器的联合作用可产生依赖于波长的损耗,以补偿光纤光栅两反射峰峰值的大小差异。基于以上原理,通过调节腔内的偏振态,该激光器实现了室温下稳定的双波长输出,也实现了在两波长之间的转换。两波长激光均有超过45 dB的信噪比,最大的功率波动为0.8 dB     

The effect of variable PSP angles in a PMD compensator

A polarization mode dispersion compensator (PMDC) composed of two polarization mode dispersion (PMD) elements and one polarization dependent loss (PDL) element is proposed. Simulation shows that, due to the variable angle between the two principal states of polarization (PSPs) of the compensator, the proposed compensator can improve the PMD compensation efficiency for systems with both PMD and PDL, especially when higher order PMD is compensated.     

熔锥型保偏光纤耦合器分光比的偏振依赖研究

实验研究了熔锥型保偏光纤耦合器分光比随入射单色线偏振光偏振方向的旋转所呈现的周期性,验证了保偏光纤耦合器分光比的偏振依赖特性.借鉴已成熟的单模光纤耦合器的倏逝场耦合模理论,对这一偏振依赖分光比的周期性规律提出了一种理论解释.在实验结果的规律性基础上,经验拟合出了分光比与单色线偏振光输入偏振角的函数关系.     

强双折射光纤中色散效应对偏振模传输的影响

本文研究了在强双折射光纤中色散效应对偏振模传输的影响.发现当二阶色散系数较大时,偏振模能稳定传输,但所需入纤功率较高;当降低二阶色散影响以降低对光源要求时,三阶色散对偏振模长距离传输起破坏作用,三阶色散参量越大,对偏振模的破坏也越大.     

Field Measurements of Polarization Mode Dispersion

Polarization mode dispersion (PMD) measurements are presented for a sample of installed optical fibers. High PMD values are fairly common, with 9 of the 71 fibers having PMD coefficients above 0.3 ps km1 2. The results are analyzed in terms of the age of the fibers and the type of cabling. Measurements are presented for a number of concatenated fiber links, and the results show that the PMD value of the link is approximately equal to the square root of the sum of the squares of the PMD values of the individual fibers.     

Switchable dual-wavelength Erbium-doped fiber ring laser with cascaded fiber Bragg gratings

We have experimentally shown wavelength mode switching in a dual-wavelength Erbium-doped single cavity fiber laser where the initial two wavelengths of 1 nm spacing are determined by the cascaded reflection type short-period fiber Bragg gratings having two different centre wavelengths of 1550.5 and 1551.5 nm. The lasing mode depends on the polarization in the ring cavity to migrate from one wavelength to another or operates in both modes in a polarization beam splitter output. To effectively control the polarization in the ring cavity, the polarization controllers were positioned before and after the polarization beam splitter. This method of wavelength switching provides a simple way of mode tuning in dual-wavelength fiber lasers.     

All-fiber single polarized Yb-doped fiber laser with a high extinction ratio

We present an all-fiber design for a single polarization Yb-doped fiber laser with all-fiber connections spliced. Single polarization with a high extinction ratio was achieved by the design of a laser cavity consisting of a fiber Bragg grating inscribed on a single-polarization fiber as a high reflective mirror and a piece of end-cleaved single-polarization fiber as an output coupler. The fiber laser operates at 1063.25 nm with an output power of 1.7 W, an optical signal- to-noise ratio of 70 dB and a narrow bandwidth of 54 pm. The laser output has a polarization extinction ratio of 700:1 or 28 dB, and a very stable power output.     

Improved models of optical fiber birefringence—Part II

In this paper, we employ several general models (introduced in Part I) for the evolution of optical fiber birefringence with longitudinal distance to analyze, both theoretically and numerically, the behavior of the polarization mode dispersion (PMD) in single mode fibers. We find that while the probability distribution function of the differential group delay varies along the fiber length as in existing models, the dependence of the root mean square differential group delay (DGD) on fiber length differs noticeably from earlier predictions.     

Improved models of optical fiber birefringence—Part I

Current models of birefringence in optical fibers assume that the birefringence vector varies randomly either in direction with a fixed magnitude or simultaneously in both magnitude and direction. Here we propose and then investigate several models in which the stochastically varying amplitude is instead restricted to a limited range.     

Origin and System Effects of Polarization Mode Dispersion in Chirped Bragg Gratings

Polarization mode dispersion of chirped Bragg gratings is analyzed in terms of key birefringence phenomena and impact on telecommunication systems performance. The influence on polarization mode dispersion (PMD) of fiber birefringence, grating chromatic dispersion, and ripples of the group delay curve is pointed out. Polarization mode dispersion influence on systems performance is investigated by numerical simulations and transmission experiments at 10 Gbit/s. The deterministic nature of Bragg gratings PMD determines a moderate, upper-limited system penalty for a transmission line employing a single compensating device. However, in the case of broadband components, a non-negligible PMD penalty may be observed due to the difficulty of controlling accurately the group delay linearity.     

对轴误差对光纤陀螺输出的影响

理论分析并试验研究了Y波导保偏尾纤与保偏光纤线圈之间熔接点的对轴误差对光纤陀螺输出的影响.根据简化的光纤陀螺光路误差模型,对光纤陀螺的输出相位误差与光路中主要耦合点的对轴误差的关系进行了理论推导和仿真分析,并利用一个实际的闭环光纤陀螺试验研究了主要熔接点的对轴误差变化对光纤陀螺零偏和零偏稳定性的影响.结果表明,Y波导保偏尾纤与保偏光纤线圈之间的对轴误差是引起光纤陀螺输出误差的重要因素,必须尽量减小.