Linear Quasi-chirp-free Tuning of Fiber Grating with Torsional Beam

A new method of linear tuning for fiber grating with the torsional beam is reported for the first time to our knowledge. The theoretical analyses and the experimental results show that the Bragg wavelength change is linear to the torsional angle and the torque when the torsional strain of the torsional beam is very small. The linear quasi-chirp-free tuning of the fiber grating can be realized when the range of the torsional angle of the column beam is between -45°and +45°and the wavelength range of linear tuning is not less than 7 nm. Tuning sensitivities are 0.0867 nm/degree and 6.27 nm/Nm, respectively.     

用单光纤光栅实现扭转与温度的双参量传感测量

采用一种新颖的扭梁设计结构 ,利用单光纤光栅成功地实现了扭转 (扭转角或扭矩 )与温度的双参量同时测量。该方法能够有效地解决扭转角与温度的交叉敏感问题 ,且光纤光栅波长的变化对扭转角、扭矩及扭应力 (力臂一定时 )均呈线性关系。在 - 40°～ +32°范围内 ,扭转角、扭矩和温度的传感灵敏度分别达到 0 .19nm (°)、3.2 9nm Nm和 0 .0 3nm ℃ ,波长线性调谐范围可达 14.2 0nm。     

新型光纤光栅中心波长与带宽独立调谐方法

提出了一种新型光纤光栅中心波长与带宽独立调谐方法，将光纤光栅沿圆柱形弹性梁的轴向成一定角度粘贴于侧面，通过改变梁的扭转角与侧向位移，实现了光纤布拉格光栅中心波长与带宽的准线性独立调谐，实验上获得了8．28nm准无啁啾波长调谐和5．32nm准无中心波长漂移的带宽调谐，实验结果与理论分析一致.     

Tunable Bragg gratings for fiber lasers

A tuning method of a fiber Bragg grating by the bending compression-tension is considered. With this method, a relative tuning range of the resonance wavelength of the grating of about 5% has been obtained. The changes in the shape of the spectrum and in the grating reflectivity during the tuning process are studied. The reflectivity of the fiber Bragg grating has been found to considerably increase with increasing degree of compression. It is shown that such an increase is caused by compression-induced changes in the refractive index modulation amplitude in the grating. The fiber Bragg grating developed has been applied for tuning the radiation wavelength of an ytterbium fiber laser. The tuning range of the laser has been found to be 45 nm around the central wavelength 1080 nm.     

基于悬臂梁的光纤光栅无啁啾线性调谐

设计了一种均质,等厚,等腰三角状悬臂梁,调节该梁自由端的挠度,实现了光纤光栅布拉格反射中心波长的线性无啁啾调谐（调谐范围４．５０ｎｍ）引入修正因子η＝０．７１后,理论值与实验结果基本一致,光栅与梁间刚性粘贴的质量影响反射谱形状。     

新型光纤光栅扭转传感器研究

报道了一种新型光纤光栅扭转传感器的基本原理和传感结构,推导了扭转测量的理论公式,该传感器的扭角与光纤光栅中心波长的变化呈线性关系.在±40°扭角范围内,技术上实现了灵敏度为10.715°/nm的扭转传感.     

光纤布拉格光栅电流传感的理论和实验研究

对皮磁致伸缩棒调谐光纤布拉格光栅为基础的新型电流传感器进行了理论和实验研究。将一个光纤布拉格光栅牢固地粘贴在一置于多层螺线管中心部分的磁致伸缩棒上，构成传感头。当通过螺线管的电流改变时，磁致伸缩材料在均匀磁场的作用下产生沿纵向的应变并传递到光纤光栅上，从而导致光纤光栅的布拉格波长移动。外加电流和波长移动之间的关系是线性的，线性调谐的波长范围为0.9nm，电流强度范围为900mA，灵敏度约为1000mA/nm，电流强度可精确到10mA。理论和实验符合得很好。     

光纤光栅压力传感器中应力迟滞的消除方法

提出了一种利用双光纤光栅消除光纤光栅压力传感器中应力迟滞的方法.将两个相同波长的光纤布拉格光栅分别对称粘贴于悬臂梁的上下表面并串接在一起，外压力作用下可实现调谐双光栅布拉格波长差.研究结果表明，该方法可消除弹性元件材料所引起光纤光栅压力传感器的应力迟滞，改善传感器的线性响应特性和重复性，在0~40 MPa的压力范围内，双峰波长差的调谐范围为5.12 nm，是单峰波长调谐范围的2倍，压力调谐双峰波长差的灵敏度可达0.128 nm/MPa，是压力调谐单峰波长灵敏度的2倍.     

Wavelength Tuning of Long-Period Fiber Gratings by Fabrication Using a Tilted Amplitude Mask

We propose a method of tuning resonant wavelengths in the fabrication process of a long-period fiber grating using an amplitude mask tilted relative to the fiber. We irradiated a hydrogenated single-mode fiber with a KrF excimer laser through a tilted amplitude mask with a grating period of 460 Μm. Growth of resonant loss peaks in transmission spectra was measured for various tilt angles. A tuning range up to 329 nm was obtained by tilting up to 45°. The measured results agreed with numerical simulation. It was shown that using only an amplitude mask it is possible to fabricate a long-period fiber grating having resonance at any wavelength throughout the range of 1.2-1.6 Μm. A method to determine the tilt angle for a designed wavelength is discussed.     

基于变截面梁的光纤光栅线性无啁啾调谐

从理论上分析了利用变截面（等强度）弹性梁实现光纤光栅波长线性、无啁啾调谐的基本原理，给出了实现无啁啾波长调谐的弹性梁截面满足条件及其设计方案，并讨论了矩形等截面和变截面悬臂梁调谐方案的特点.理论分析与实验结果均表明，通过对变截面梁侧向施加载荷，可以实现光纤光栅中心波长的线性无啁啾调谐，且系统结构简单、易于设计.     

新型光纤光栅线性调谐方法

报道了一种线性度极佳的光纤光栅波长调谐技术，调谐范围在１０ｎｍ，线性拟合度达到０．９９９８，并首次利用材料力学原理推导了这种线性调谐的理论关系式，此种技术在可望在光纤传感，光纤通信及激光技术等方面有重要应用前景。     

基于光纤光栅的波长可调谐光分插复用器

本文报道了一种基于光纤光栅的波长可调谐光分插复用器.可连续线性调谐5.3nm来选择不同的信道进行上下载信息.用宽带光源对该器件的性能进行了测试;用该器件在4波长全光纤激光器作信号源的光纤通信传输实验系统中做了解复用实验.实验表明该器件能很好地下载光信号,相邻信道隔离度达到29dB,具有一定的应用价值.     

Wideband tunable linear-cavity fiber laser source using strain-induced chirped fiber Bragg grating

A novel wideband tunable linear-cavity fiber laser source using strain-induced chirped fiber Bragg grating (FBG) and erbium–ytterbium co-doped fibers is proposed and demonstrated for the first time. The strain-induced chirped FBG, which acts as a partial-reflecting mirror, is achieved by bending a uniform FBG bonded at a slant onto the lateral surface of a simply supported beam. A single wavelength lasing with a maximum wavelength tuning range of 17 nm has been achieved experimentally.     

基于光谱合束技术的透射光栅模拟设计

半导体激光器光谱合束技术能够实现近衍射极限的高功率激光输出,已成为当前研究热点。衍射光栅的性能直接决定光谱合束的激光输出效果。模拟设计了一种针对940 nm波长、熔融石英材料的亚波长透射光栅。基于严格耦合波理论对光栅结构进行初步设计,运用Rsoft软件依次对光栅占空比、脊高和周期等参数进行优化确定,同时分析了各个参数对光栅衍射效率的影响。所设计的透射式光栅实现第-1级衍射级次的波分复用功能,衍射效率达到91.2%(TE模式),同时压缩其他衍射级次,使其衍射效率降到1.2%以下。同时在光栅入射角度59°±3°范围内保持90%以上的衍射效率,实现高功率激光输出的同时具有较高的误差容错率,易于调节,满足光谱合束技术的要求。     

锁模脉冲波长连续可调谐光纤激光器

利用在腔内加入可调谐光纤光栅滤波器使“8”字形腔掺Yb3+光纤激光器在锁模状态下实现波长连续可调谐.实验中,在保证锁模状态稳定的情况下,通过调节可调谐光纤光栅滤波器,使激光器输出锁模脉冲的中心波长在1 047 nm～1 055 nm范围内连续调谐,重复频率稳定维持在4.9 MHz.在中心波长1 053 nm处,测得锁模脉冲输出平均功率为8.02 mW,光谱带宽1 nm,脉冲宽度为259.3 ps.这种“8”字形腔被动锁模光纤激光器在锁模状态下对波长连续可调谐,并可长时间稳定工作.     

Wavelength tunable high power laser using a double-clad Er:Yb doped fiber

We experimentally demonstrated a stable, wavelength-tunable fiber laser using a polarization-maintaining, double-clad Er:Yb doped fiber amplifier in the cavity. The output wavelength is tunable over the range from 1535 to 1567 nm using a fixed grating and the dichroic mirror placed on a rotational mount; under rotation of the dichroic mirror the tuning ratio of 50 nm/deg was found. We studied the wavelength tuning range dependence on the amplifier fiber length and achieved a maximal output power of 850 mW. This configuration can be Q-switched for high peak power and its narrow bandwidth is suitable for nonlinear optics applications, such as parametric teraherthz generator.     

一种利用相位掩模版对光栅波长进行微调的光栅刻写方法

提出并实验证实了一种刻写光栅时既能保护相位版又能对光栅的反射波长进行微调的方法.通过调整光纤和相位版之间的距离,利用1 550 nm单模光纤和掺铒分别实现了0.48 nm和2.2 nm的光栅反射波长的调节.在相位版和光纤之间的距离保持在3 mm的条件下,既可以保护相位版又可以获得高质量的光栅.     

高功率宽调谐范围掺Yb3+光子晶体光纤激光器

采用闪耀光栅作为色散元件,构建了前向、后向输出两种结构的可调谐掺Yb3 光子晶体光纤激光器,并对其输出特性进行了分析研究.在抽运功率5.75W时,前向输出结构实现了1050.6～1110.2 nm的连续调谐输出,光谱线宽约0.1 nm,边模抑制比大于44 dB.在调谐激光波长为1085 nm时,得到最高输出功率677 mW.结构改进的后向输出结构的可调谐输出结构在抽运功率4.43 W,调谐波长1075 nm,实现了2.21 W的功率输出,斜率效率为73%;调谐范围50.9 nm(1042.1～1093 nm),光谱线宽小于0.08 nm,边模抑制比大于50 dB.两种结构的可调谐激光器输出均为线偏振光,偏振度大于89.5%.     

普通单模光纤色散补偿传输的实验研究

利用自行设计的悬臂梁调节机构,对１２ｃｍ长的均匀光纤光栅进行中心波长和啁啾的同时线性调谐后,将其应用于２０Ｇｂ／ｓ、１００ｋｍ普通单模学纤的色散补偿实验中,取得了良好的补偿效果。     

一种简单的光纤光栅电调谐方法

采用较简单的双点源真空蒸发法在光栅外表面上蒸镀一层均匀铝膜,利用电流流过铝膜时产生的电阻热改变光栅的温度而使光栅的中心波长向长波方向发生改变.光栅中心波长的变化与所加电流的平方成正比.实验中用较小的电流(约43mA)获得了较大的波长调谐范围(约4nm),其调谐精度达到2.15×10^-3nm/(mA)².