双线法测量横向阻抗中双线间距及线径的影响

 根据双线法测量横向阻抗的原理,从理论和模拟计算两方面对双线间距、线径因素造成的系统误差进行讨论。给出谐振腔近似下双线法测量横向阻抗的等效电路,通过此等效电路对双线间距、线径因素造成的系统误差进行讨论。通过模拟计算的方法分析了双线法测量类腔体TM110模式横向阻抗时,不同双线间距、不同线径带来的系统误差,模拟计算的结果与等效电路结果分析得到的定性结果一致。模拟计算分析表明,对于管道半径为50 mm的类腔体结构,线径小于6 mm及双线距离小于50 mm时,双线间距及线径引入的横向阻抗系统误差小于8%。     

随机耦合模型中损耗因子的分析与获取

随机耦合模型(RCM)是研究电磁脉冲干扰下波混沌系统中感应电压统计预测的新方法,其中波混沌腔体损耗因子的获取是这种方法使用的关键。从随机耦合模型理论出发,分析了损耗因子对腔体阻抗随频率变化特性的影响,探讨了不同损耗因子下归一化阻抗矩阵的统计特性,提出了使用腔体散射阻抗与辐射阻抗的比值作对照,以快速获取腔体损耗因子的新方法。     

中、高能电子被SO2分子散射的微分截面、动量转移截面及弹性积分截面

在考虑分子内成键原子间的电子云重叠效应的基础上, 提出了一种能够准确计算“中、高能电子-分子”散射的微分截面、动量转移截面及弹性积分截面的修正势方法. 利用可加性规则、使用Hartree-Fock波函数并采用被这一方法修正过的复光学势, 在100—1000eV内对电子被SO₂分子散射的微分截面、动量转移截面及弹性积分截面进行了计算, 并将计算结果与实验及其他理论结果进行比较. 结果表明, 利用这一修正过的复光学势及可加性规则获得的微分截面比利用未修正的复光学势及可加性规则得到的结果准 关键词： 可加性规则 微分截面 动量转移截面 电子散射     

瞬态热传导问题的复变量重构核粒子法

在重构核粒子法的基础上,引入复变量,讨论了复变量重构核粒子法.复变量重构核粒子法的优点是在构造形函数时采用一维基函数建立二维问题的修正函数.然后,将复变量重构核粒子法应用于瞬态热传导问题的求解,结合瞬态热传导问题的Galerkin积分弱形式,采用罚函数法引入本质边界条件,建立了瞬态热传导问题的复变量重构核粒子法,推导了相应的计算公式.与传统的重构核粒子法相比,复变量重构核粒子法具有计算量小、精度高的优点.最后通过数值算例证明了该方法的有效性. 关键词： 重构核粒子法 复变量重构核粒子法 修正函数 瞬态热传导问题     

100～5 000 eV下电子被等电子(Z=10)分子CH4、H2O、HF及NH3散射的总截面计算

利用可加性规则,使用Roothaan-Hartree-Fock波函数,在100～5 000 eV下首次采用由束缚原子概念修正过的复光学势,对电子被等电子(Z=10)分子CH4、H2O、HF和NH3散射的总截面进行了计算.束缚原子不同于自由原子之处,是束缚原子考虑了在不同分子中电子云的不同重叠,将计算结果与实验及其它计算结果进行了比较.结果表明,利用被束缚原子概念修正过的复光学势及可加性规则进行计算,其结果的精度要比利用未被束缚原子概念修正过的复光学势及可加性规则进行计算得到的结果好.     

中、高能电子被SO2分子散射的微分截面、动量转移截面及弹性积分截面

在考虑分子内成键原子间的电子云重叠效应的基础上,提出了一种能够准确计算“中、高能电子-分子”散射的微分截面、动量转移截面及弹性积分截面的修正势方法.利用可加性规则、使用Hartree-Fock波函数并采用被这一方法修正过的复光学势,在100—1000eV内对电子被SO2分子散射的微分截面、动量转移截面及弹性积分截面进行了计算,并将计算结果与实验及其他理论结果进行比较.结果表明,利用这一修正过的复光学势及可加性规则获得的微分截面比利用未修正的复光学势及可加性规则得到的结果准确得多,计算得到的动量转移截面及弹性积分截面在入射电子能量不低于200eV时也都比较接近实验值.     

基于BLT方程的双层腔体屏蔽效能计算方法

基于波导理论,将BLT方程进一步拓展,提出一种可快速、准确地计算双层腔体内任意点屏蔽效能的方法。首先将腔体壁孔所在面等效为二端口网络,腔体等效为两端短路的波导,建立信号流图。引入孔阻抗计算二端口网络散射参数,依据信号流图构建广义BLT方程,得到内层腔体中心线上点的屏蔽效能;然后根据波导理论的场分布特性,推导出腔体内任意点电场与腔体中心线上电场的关系,最终得到内层腔体内任意点的屏蔽效能。将计算结果与等效电路法及CST数值仿真结果对比,三者吻合良好,计算结果在较大频率范围内比等效电路法精度更高。该方法可以准确预测双层腔体在0~2.5GHz范围内所有谐振点,有助于分析腔体谐振现象,且计算效率较高,占用资源大幅减少。     

中高能正电子被CO,HCl,NH3及SiH4散射的总截面

利用可加性规则,使用Hartree-Fock波函数,采用由束缚原子概念修正过的复光学势(由静电势、极化势及吸收势三部分组成),在30-3000eV内对正电子被CO,HCl,NH3和SiH4散射的总截面进行了计算,且将计算结果与实验结果及其他理论计算结果进行了比较.结果表明,利用被束缚原子概念修正过的复光学势及可加性规则进行计算,所得结果与实验结果的符合程度要比利用未被束缚原子概念修正的复光学势及可加性规则进行计算得到的结果好很多.因此,在复光学势中采用束缚原子概念可提高正电子被分子散射的总截面的计算准确度.     

任意形状金属腔体内电磁脉冲的三维计算

提出了模拟任意形状腔体中的内电磁脉冲的三维直角坐标系时域有限差分(FDTD)算法。该算法采用FDTD共形网格技术模拟任意形状腔体的边界,可以解决腔体内非对称的边界问题。推导了射线斜入射的差分方程,进行了三维数值计算,并采用直角坐标系FDTD算法和柱坐标系FDTD算法计算了射线斜入射圆柱腔体产生的内电磁脉冲,二者吻合很好,验证了直角坐标系FDTD算法正确性。     

一种新的计算复杂目标电磁散射的MoM-SBR/PO混合法

针对三维复杂电大尺寸金属目标,在传统MoM-PO混合法的基础上,引入基于射线密度归一化(RDN)概念的射线弹跳法(SBR),计算电大PO区域内部的多次反射影响,从而得到一种新的MoM-SBR/PO混合方法,该方法区别于大部分改进的MoM-PO混合法对PO区域内多次反射贡献的处理,避免了迭代物理光学法涉及的多次矩阵相乘问题.与其它几种方法进行比较,结果显示吻合较好.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.     

Direction-of-arrival estimation using matrix spatial prefiltering approach

An approach to direction-of-arrival （DOA） estimation for multiple narrowband farfield signals is proposed. The technique uses a novel matrix spatial prefiltering approach. Specifically, a matrix filter is designed to spatially filter the incoming data snapshots. The un-wanted components arriving from the stopband angular sectors are attenuated and the desired components from the angular sector of interest pass with minimal distortion. The matrix filter spatially filters the element-space data and the output reserves the element-space data property, which makes it very useful by passing sensor data through a spatial prefilter prior to applying many other array processors to attenuate interferences and improve system performance. Several examples of DOA estimation problem are presented to illustrate the performance of the proposed spatial prefiltering approach. Results of simulation and real data show that the pre-filter can efficiently attenuate the spatial interferences and significantly improve the estimation and resolution capability of DOA estimators at low signal-to-noise ratios for the sources located inside the passband sector. In addition, the use of spatial prefilter makes it possible to estimate DOAs for multiple sources more than the number of the elements of an array.     

Quantum efficiency calibration of opto-electronic detector by means of correlated photons method

A new calibration method of detectors can be realized by using correlated photons generated in spontaneous parametric down-conversion (SPDC) effect of nonlinear crystal.An absolute calibration system of detector quantum efficiency is performed.And its principle and experimental setup are introduced.A continuouswave (CW) ultraviolet (351 nm),diode-pumped,frequency-doubled,and solid-state laser is used to pump BBO crystal.The quantum efficiencies of the photomultiplier at 633,702,and 789 nm are measured respectively.The coincidence peaks are observed using coincidence circuit.Some measurement factors including the filter bandwidth of trigger channel,the detector position alignment and polarization of the pump light are analyzed.The uncertainties of this calibration method are also analyzed,and the relative uncertainties of total calibration are less than 5.8%.The accuracy of this method could be improved in the future.