SiO2纳米微球表面结构在可见光波段的减反特性

研究了不同尺寸SiO2胶体微球形成纳米结构薄膜的光学传输特性和光子带隙。通过在玻璃基底上自组装透光的SiO2胶体微球形成胶体晶体薄膜, 依据布拉格定律,分析微球尺寸对胶体晶体光子带隙的影响。为实现可见光波段的全方位减反射,提出通过改变胶体粒径将胶体晶体带隙位置移动至紫外波段,理论计算得出当粒径为112 nm,占空比为0.45时能实现可见光波段0.5%的平均反射率。实验结果表明,玻璃基底在400~800 nm间的平均反射率从4.3%降低至0.7%,最小反射率达0.3%。通过控制微球粒径移动光子带隙位置,优化晶体结构参数实现了可见光波段的减反射,有效提高了光学组件对可见光的利用率。     

一维Au/MgF2光子晶体的透射性质

理论上研究了一维金属/电介质光子晶体的透射率性质，用传输矩阵方法数值计算了Au/MgF2光子带隙晶体的透射率．发现周期性结构产生的透射共振会大幅度增加光通过层状金属的透射率．通过调节一维Au/MgF2光子晶体中金和氟化镁的厚度以及周期数，得到了可见波段的高透射允带，透射率在0.4以上，而对于可见波段以外的频率几乎是完全不能传输的．这种结构在保持了高透射率的前提下还具有金属的优点，这在传感器、护目装置、反射窗、液晶显示等诸多领域都有很大的实用价值．     

共轭荧光分子光子晶体发光材料的可控制备与性能研究

利用自组装技术结合溶胶-凝胶法成功制备了高度有序且光子带隙可控的聚甲基丙烯酸甲酯蛋白石光子晶体样品,并对其表面形貌、透射光谱和发射光谱进行了表征,研究了光子带隙与微球直径、带隙位置与入射光角度之间的依赖关系。     

一维无序结构光子晶体的能带特性研究

通过引入结构参数a，深入研究了具有无序结构的一维二元光子晶体的能带特性。研究发现，无序结构有效拓宽了光子带隙，与均匀结构相比，拓宽率达到200％以上；无序一维光子晶体表现出从可见到红外很宽区域的高反射特性。本文还计算和分析了入射角和无序度D对光子晶体带隙的影响。     

空芯光子晶体光纤光子带隙的测量与数值模拟

用全矢量平面波法计算三角结构光子晶体光纤的带隙. 用透射法测量了自制的空芯光子晶体光纤的透射谱,得到了它在可见光波段透射强度与波长的关系,并在随后的实验中观测到了传光的模场图.通过理论模拟了实验所用的空芯光子晶体光纤的带隙图,与实验结果具有较好的一致性. 关键词： 空芯光子晶体光纤 光子带隙 全矢量平面波法 透射     

一种发光二极管模型中无序光子晶体对光输出影响的研究

摘要利用Order-N算法及超晶格技术讨论了位置无序及尺寸无序对石墨点阵柱状光子晶体光子带隙的影响.计算结果表明，对于电场偏振模，光子带隙对尺寸无序更加敏感.在此基础上，利用三维时域有限差分方法进一步讨论了无序光子晶体对石墨点阵柱状中心柱光子晶体GaN发光二极管模型光输出效率的影响.计算结果表明，无序对这种光子晶体发光二极管模型光输出效率的影响较小，且这种影响也是随机的.     

一维光子晶体带隙结构研究

在考虑介质色散的基础上,研究了介质层厚度对光子晶体带隙结构的影响.利用传输矩阵法,计算了以LiF和Si两种材料组成的一维光子晶体带隙结构.结果表明,介质层厚度的增加会引起禁带的红移,厚度减小会引起蓝移.分析了含空气缺陷层、金属缺陷层的光子晶体结构,发现空气缺陷层对带隙结构的高反射区域变化不大,而在低反射区域,反射系数为零的波带之间出现了两边反射系数增加,中间反射系数减小的情况.在金属缺陷层的带隙结构中,金属对整个波长范围光的吸收作用不同,金属对低反射区1.6 μm、1.85 μm处透射率较大的透射光吸收作用明显,而在1.28~1.38 μm处透射率波长区间,几乎无吸收.     

FCC结构胶体光子晶体的制备及其带隙特性测量

基于对光纤传输特性和胶体光子晶体制备方法的研究,提出了用外加电场控制的方法制备光子带隙位于通讯波段的FCC结构的胶体光子晶体,并用光纤系统测试胶体光子晶体的带隙特性.采用RSOFT模拟了胶体光子晶体的带隙,分析了带隙位于通讯波段时所需的胶体微球的基本参量(微球折射率和直径).采用自组装的方法,用步进电机控制玻璃基片向上的拉升速率.速率为5 μm/s,同时外加一电场.用扫描电镜观测胶体晶体的表面形貌,并设计了单模光纤系统测量胶体光子晶体的带隙特性.测试的透射谱线表明胶体光子晶体的带隙中心波长为1552 nm.测试结果和模拟结果具有很好的一致性,误差只有2 nm.     

可用于拓宽光波单向传输带宽的光子晶体异质结构界面

基于光波单向传输的全光二极管在集成光通信、全光网络和光信息处理中有重要应用.基于方向带隙失配设计的光子晶体异质结构可实现光波单向传输,但正向透射率较低,带宽较窄.基于对光子晶体异质界面倾斜角度的研究,根据界面全反射条件,利用可集成材料硅和二氧化硅设计了一种空气孔型二维光子晶体异质结构.异质结构界面两侧的光子晶体对1550 nm波长附近的TE模光波在Γ-X方向均呈导带,避免了方向带隙失配.研究发现当异质界面满足全反射条件时,由于光子晶体的自准直效应,较宽波段的正向光波得以高效传播,而反向光波在界面由于全反射而被禁止传播.光子晶体异质结构界面的全反射效应打破了方向带隙对光波单向传输的限制,使得反向光波在光子晶体中为导带时同样可实现近零透射率,从而拓宽了光波单向传输的波长范围.基于全反射界面的光子晶体异质结构经过优化后,其正向透射率达0.64,透射对比度为0.97,单向传输带宽可达553 nm.     

紫外线波段一维Ag/MgF_2光子特性的理论研究

利用传输矩阵方法对一维Ag/MgF2光子晶体的带隙特性进行了研究。构建了由Ag和MgF2组成的一维光子晶体结构模型,以此模型为基础详细讨论了填充比、周期层数、入射角等参数对光子晶体带隙结构的影响,并讨论了造成吸收的原因。研究结果表明,与其他金属光子晶体的研究结果相比,该结构的金属光子晶体在紫外线波段具有高反射率的光子带隙,属于不完全带隙的一维光子晶体,适用于制作紫外线波段的光学反射镜。     

Study on the anisotropic photonic band gaps in three-dimensional tunable photonic crystals containing the epsilon-negative materials and uniaxial materials

In this paper, the properties of anisotropic photonic band gaps (PBGs) for three-dimensional (3D) photonic crystals (PCs) composed of the anisotropic positive-index materials (the uniaxial materials) and the epsilon-negative (ENG) materials with body-centered-cubic (bcc) lattices are theoretically studied by a modified plane wave expansion (PWE) method, which are the uniaxial materials spheres inserted in the epsilon-negative materials background. The anisotropic photonic band gaps (PBGs) and one flatbands region can be achieved in first irreducible Brillouin zone. The influences of the ordinary-refractive index, extraordinary-refractive index, filling factor, the electronic plasma frequency, the dielectric constant of ENG materials and the damping factor on the properties of anisotropic PBGs for such 3D PCs are studied in detail, respectively, and some corresponding physical explanations are also given. The numerical results show that the anisotropy can open partial band gaps in such 3D PCs with bcc lattices composed of the ENG materials and uniaxial materials, and the complete PBGs can be obtained compared to the conventional 3D PCs containing the isotropic materials. The calculated results also show that the anisotropic PBGs can be manipulated by the parameters as mentioned above except for the damping factor. Introducing the uniaxial materials into 3D PCs containing the ENG materials can obtain the larger complete PBGs as such 3D PCs with high symmetry, and also provides a way to design the tunable devices.     

Frequency bands of negative refraction in finite one-dimensional photonic crystals

We have discussed theoretically the negative refraction in finite one-dimensional (1D) photonic crystals (PCs) composed of alternative layers with high index contrast. The frequency bands of negative refraction are obtained with the help of the photonic band structure, the group velocity and the power transmittance, which are all obtained in analytical expression. There shows negative transverse position shift at the endface when negative refraction occurs, which is analysed in detail.     

高质量三维光子晶体的实验制备及理论分析

对压强控制自组装法进行了改进,采用了密封硅胶颗粒的强吸水装置,为光子晶体样品的制备提供了一个稳定的温度、湿度和压强环境.将温度、压强分别控制在35 ℃、45 mmHg,利用直径为260 nm的聚苯乙烯胶体球进行了高质量三维光子晶体样品的制备.从理论计算和实验测量等方面对制备的光子晶体样品的结构、质量和性能进行了对比分析,结果表明,利用该实验装置进行光子晶体样品的制备时,可重复性高;制备的光子晶体样品具有较为完美有序的密堆结构,质量较好;在光子晶体样品的Г L方向有深且窄的光子带隙和陡峭的带隙边沿.光子带隙深度为83%,宽度为0.073,带隙边沿陡峭度为8%/nm,这为超快全光开关等先进的光学设备的研究奠定了基础.     

高质量三维光子晶体的制备及其透射谱研究

设计了简易的压强可控自组装实验装置,制备了由直径为260 nm的聚苯乙烯(PS)胶体球组成的面心立方光子晶体.分析了压强的变化对光子禁带(PBG)深度及光子带隙边缘(PBE)坡度的影响,确定了合适的压强生长环境(P=5999.5 Pa).利用该实验装置,还进行了光子晶体的小批量制备,一次性制得了三块光子晶体,并从不同角度对每一块光子晶体的透射谱及不同光子晶体的透射谱进行了测量.同一光子晶体不同位置透射谱的重合、同一批次制备的不同光子晶体透射谱的一致性及光子禁带两侧的Fabry-Pérot振荡等均说明:该装置制备的光子晶体在大区域、大面积上是高度有序、均一和平整的;利用该实验装置进行光子晶体的小批量制备是可行的.     

反常色散材料光子晶体中光输运的光学控制

研究了光抽运对由铯原子蒸气构成的光子晶体的影响.研究发现,利用较弱光强的线抽运光即可显著地改变这种反常色散光子晶体的透射率.而利用圆偏振光抽运可以进一步降低抽运光的阈值,并在反常色散光子晶体中获得极大的法拉第旋转.反常色散光子晶体的这些特性为光控光开关的研究和制作提供了一条新途径.     

外磁场与温度对低温超导光子晶体低频禁带特性的影响

文中用传输矩阵法(TMM)分析了TM波垂直入时,超导光子晶体的低频禁带特性,并讨论了外磁场与温度对禁带的影响.分析结果表明:超导光子晶体存在频率从0开始的低频禁带;当没有外磁场作用时,由于超导中正常态电子的影响,低频禁带的截止频率与温度无关;有外磁场作用时,温度才对截止频率具有可调性.外加恒定磁场时,低频禁带的截止频率随温度升高而减小;而在正常态电子的作用下,温度对处在超导态超导光子晶体禁带截止频率的调节范围相对忽略正常态电子情况下减小.恒温下,通过调节外磁场来控制带隙时,正常态电子的贡献很小可忽略不计;外磁场强度增大禁带截止频率减小.当超导体完全处于正常态时,低频禁带消失.     

Broad Stopband Characteristic of Dielectric Chiral Photonic Crystals

In this paper, a novel chiral photonic crystal structure is presented. The formula of reflection coefficient of multi-layer chiral media is applied to dielectric-chiral photonic crystal structure, which is composed of thin chiral layers sandwiched by conventional media. To compare with previous literature, we consider the dielectric structure with alternate glass and GaAs layers. The power reflectance as a function of wavelength for this photonic crystal structure has been calculated. The results are in good agreement with that of Reference. However, our method is simpler. From these graphs, it is found that 100% reflectance is only in finite wavelength ranges, and reflection bandwidth is also small for conventional photonic crystal structure. For chiral photonic crystal, the results show that the chiral photonic band gap (PBG) structure gives nearly 100% reflections in the near-infrared region in addition to some parts of the visible region of the wavelengths. Therefore, it can be used as a broadband reflector and filter.     

Photonic band gap of one-dimensional periodic structure containing dispersive left-handed metamaterials

Band structures of one-dimensional(1D)photonic crystals(PCs)containing dispersive left-handed metamaterials are studied theoretically.The results show that the structure possesses a type of photonic band gap originating from total internal reflection(TIR).In contrast to photonic band gaps corresponding to zero average refractive index and zero phase.the TIR gap exhibits sharp angular effect and has no polarization effect.It should also be noted that band structures of transverse electric(TE) and transverse magnetic(TM) mode waves are exactly the same in the PCs we studied.     

Characteristics of local photonic state density in an infinite two-dimensional photonic crystal

The local density of photonic states （LDPS） of an infinite two-dimensional （2D） photonic crystal （PC） composed of rotated square-pillars in a 2D square lattice is calculated in terms of the plane-wave expansion method in a combination with the point group theory. The calculation results show that the LDPS strongly depends on the spatial positions. The variations of the LDPS as functions of the radial coordinate and frequency exhibit “mountain chain” structures with sharp peaks. The LDPS with large value spans a finite area and falls abruptly down to small value at the position corresponding to the interfaces between two different refractive index materials. The larger/lower LDPS occurs inward the lower/larger dielectric-constant medium. This feature can be well interpreted by the continuity of electricdisplacement vector at the interface. In the frequency range of the pseudo-PBG （photonic band gap）, the LDPS keeps very low value over the whole Wiger-Seitz cell. It indicates that the spontaneous emission in 2D PCs cannot be prohibited completely, but it can be inhibited intensively when the resonate frequency falls into the pseudo-PBG.