碳纳米管光学天线的有效波长和谐振特性

将经典金属自由电子气模型应用于金属型碳纳米管, 基于光学天线有效波长理论, 得出了金属型碳纳米管光学天线响应的有效波长与碳纳米管介电特性之间的普适关系. 在对碳纳米管介电特性进行第一性原理计算的基础上, 以金属型4 Å碳纳米管为例, 进一步研究了金属型碳纳米管光学天线响应的有效波长与入射波长之间的关系, 以及金属型碳纳米管光学偶极子天线的谐振特性. 通过将已有传统金属光学天线和碳纳米管天线有效波长的研究结果进行对比, 验证了本文理论的正确性. 结果表明, 碳纳米管光学天线响应的有效波长与入射波长呈近似线性关系, 与传统金属材料构成的同直径光学天线相比, 碳纳米管天线显示出了更强的波长压缩能力, 并且在可见光到红外波段内易于发生谐振. 该研究方法可为碳纳米管光学天线研究提供新的思路.     

外加电场作用下碳纳米管结构稳定性及结构修饰研究

利用外加电场的方法，对多壁碳纳米管的结构稳定性进行了研究.结果表明当场强达到30 V/nm时，碳纳米管端部的结构失稳，端部碳原子间的π键被打开，外部原子开始进入到碳纳米管的结构中.利用电子显微镜作为纳米加工仪器，通过外加电场的方法在多壁碳纳米管的端部制备了非晶态碳纳米线，形成碳纳米管-纳米线复合结构.碳纳米管和纳米线结合处的σ键作为绝缘界面，形成了电子输运的势垒.     

Growth of carbon nanotubes from C<Subscript>60</Subscript>

Carbon nanotubes can be obtained from a multitude of molecular precursors in chemical vapor deposition (CVD) processes. Here we demonstrate that the use of C₆₀ as the carbon feedstock gas in an iron-catalyzed thermal CVD experiment leads to the formation of films of multi-walled carbon nanotubes. The critical role of the diameter of the catalyst particles in determining the efficiency of nanotube growth is clearly demonstrated. Electron microscopy and Raman spectroscopy were employed for the characterisation of the nanotube material. The structural properties of the individual nanotubes show distinctive differences to acetylene-grown multi-walled nanotubes. PACS 81.07.De; 81.10.Bk     

A novel integrated MEMS helix antenna for terahertz applications

This paper reports the design and analysis of a novel helix antenna based on Micro-electromechanical Systems (MEMS) technology, which is used in terahertz (THz) applications. The structure of the antenna includes two parts, the metallic helix and the coplanar waveguide (CPW) on the substrate for feed, the fabrication of the structure needs only one wafer, and the antenna can be easily integrated with other parts of on-chip circuits. There are many tunable parameters of the helix, so that high performance THz antenna can be achieved by optimizing these parameters. The proposed antenna can be manufactured by MEMS processing with low fabrication cost, suitable for many terahertz systems.     

Raman and SERS studies of carbon nanotube systems

In this paper, we report on Raman studies carried out on different carbon nanotube systems, namely single-walled and multi-walled carbon nanotubes and polymer/nanotube composites. We focus on different types of interactions which can take place in these materials. In single-walled nanotubes, the introduction of van der Waals interactions between tubes when arranged in bundles leads to an upshift of the radial breathing mode (RBM) ranging from 11 to 16 cm⁻¹ depending on the size of the bundle. In multi-walled carbon nanotubes, similar interactions between concentric tubes permit to interpret the low frequency Raman modes. In composites, PMMA/nanotubes, an upshift of the RBM is also observed, explained by the dynamical strain applied by the polymer on the bundles, in response to the breathing vibration. In addition, surface enhanced Raman scattering experiments have demonstrated the occurrence of interfacial reactions between the nanotubes and the metallic support. This is put in evidence by the degradation of tubes, especially metallic ones, and reconstruction of C₆₀-like molecules are in some cases observed.     

Radiation Properties of Carbon Nanotubes Antenna at Terahertz/Infrared Range

The geometric structure and the terahertz/infrared radiation characteristics of carbon nanotubes dipole antenna arrays have been investigated by CST MICROWAVE STUDIO based on finite integral methods. In terahertz and infrared frequency span, the antenna properties such as electrical field distributions, scattering parameters, standing wave ratio, gain, and two dimension directivity patterns are discussed. Our results show that N × N antenna arrays have higher radiation efficiency than single carbon nanotube dipole antenna. This work was supported by National Natural Science Foundation of China (60571026, 10396160).     

Terahertz radiation from armchair carbon nanotube dipole antenna

This paper investigates the electromagnetic radiation characteristics of a metallic, large aspect ratio single walled carbon nanotube antenna in the terahertz frequency region below 12.5 THz. The key features of terahertz pulse have been revealed on the carbon nanotube antenna in comparison with conventional photoconductive switching. The terahertz waveforms, radiation power and their field distributions have been evaluated and are analysed. The Fourier transformed spectra over the whole frequency range demonstrate that the carbon nanotube antenna can be used as radiation source for broadband terahertz applications.     

AFM detection of the mechanical resonances of coiled carbon nanotubes

We introduce a method for atomic force microscopy (AFM)-based detection of mechanical resonances in helix-shaped multi-walled carbon nanotubes. After deposition on an oxidized silicon substrate, the three-dimensional structure of suspended nanotubes, which bridges an artificially created step on the surface, can be visualized using AFM operating in the non-contact mode. The suspended coiled nanotubes are resonantly excited, in situ, at the fundamental frequency by an ultrasonic transducer connected to the substrate. When the AFM tip is positioned above the coiled nanotube, the cantilever is unable to follow the fast nanotube oscillations. Nevertheless, an oscillation amplitude-dependent signal is generated due to the non-linear force-to-distance dependence. Measurement of the mechanical resonances of the helix-shaped carbon nanotubes can be used to quantitatively determine their elastic properties. Assuming that a coiled nanotube can be modeled as a suspended helix-shaped uniformly thin elastic beam, the obtained resonance frequency is consistent with a Young's modulus of 0.17ǂ.05 TPa.     

Field emission characteristic of screen-printed carbon nanotube cathode

The fabrication of carbon nanotube emitters with excellent emission properties is described. The multi-walled carbon nanotubes (MWNTs) produced by chemical vapor deposition (CVD) method were purified with oxidation method and mixed with organic binding pastes and then screen-printed on glass substrates with ITO film. We applied anode voltage gradually to refine the emission behavior of the emitter by cleaning the top surface of screen-printed carbon nanotubes (CNTs). The density of the carbon nanotubes is about 2.5×10⁸/cm². Diode field emission experiments were performed in dynamic vacuum system to study the emission current, the emission uniformity, etc. Bright and stable character emission images were obtained in the diode structure and the emission current could approach 1 mA/cm².     

Absorption spectra of high purity metallic and semiconducting single-walled carbon nanotube thin films in a wide energy region

Absorption spectra of high purity metallic and semiconducting single-walled carbon nanotubes separated by the density-gradient ultracentrifugation method have been measured in the wide energy region from 1 meV to 5 eV. In the high purity metallic nanotube sample, a strong and broad absorption band has been observed at 0.06 eV. This observation suggests that the optical properties of even high purity metallic nanotube bundles cannot be explained by the simple Drude conduction model. We discuss the origin of these absorption bands for metallic and semiconducting nanotube samples by considering the existence of a small energy gap in metallic nanotube bundles and plasmon resonance.     

170keV质子辐照对多壁碳纳米管薄膜微观结构与导电性能的影响

碳纳米管具有优异的导电性, 是未来电子元器件的理想候选材料, 应用前景广阔. 针对碳纳米管在空间电子元器件的应用需求, 本文研究了170 keV质子辐照对多壁碳纳米管薄膜微观结构与导电性能的影响. 采用扫描电子显微镜(SEM)、拉曼光谱仪(Raman)、X射线光电子能谱仪(XPS)及电子顺磁共振谱仪(EPR)对辐照前后碳纳米管试样的表面形貌和微观结构进行分析; 利用四探针测试仪对碳纳米管薄膜进行导电性能分析. SEM分析表明, 170 keV质子辐照条件下, 当辐照注量高于5×10¹⁵ p/cm² (protons/cm²)时, 碳纳米管薄膜表面变得粗糙疏松, 纳米管发生明显弯曲、收缩及相互缠结现象. 目前, 质子辐照纳米管发生的收缩现象被首次发现. 基于Raman和XPS分析表明, 170 keV质子辐照后碳纳米管的有序结构得到改善, 且随辐照注量增加, 碳纳米管的有序结构改善明显. 结构的改善主要是由于170 keV质子辐照碳纳米管所产生的位移效应导致缺陷重组. EPR分析表明, 随着辐照注量的增加, 碳纳米管薄膜内的非局域化电子减少. 利用四探针测试分析表明, 碳纳米管薄膜的导电性能变差, 这是由于170 keV质子辐照导致碳纳米管薄膜中的电子特性及形态发生改变. 本文研究结果有助于利用质子辐照对碳纳米管膜结构和性能进行调整, 从而制备出抗辐射的纳米电子器件.     

Nanoelectromechanical devices with carbon nanotubes

Thanks to their excellent mechanical properties as well as interesting electrical characteristics, carbon nanotubes are among the most widely used materials for the study of electromechanical properties. This review paper presents the physical properties and the potential applications of carbon nanotube based nanoelectromechanical devices. We present an overview of fabrication methods followed by a discussion of the physical properties of CNT-NEMS. Finally some potential applications are discussed.     

Metal encapsulated nanotubes of germanium with metal dependent electronic properties

Using ab initio total energy calculations we demonstrate that the nanotubes of germanium with atomic structure based on an alternate prism and antiprism stacking of hexagonal rings, can be stabilized by metal encapsulation. The V or Nb doped infinite nanotube is metallic. However, Mo doping leads to the formation of a metal encapsulated direct band gap semiconducting nanotube of germanium. These nanotubes with metal dependent electronic properties could prove to be vital for the development of future nanotechnologies.     

Optical response of a flat metallic surface coated with a monolayer array of latex spheres

We report on the fabrication, characterization and simulation of a structure consisting of a flat metallic surface coated with a monolayer array of latex spheres. This structure shows interesting optical response: over flat metallic surfaces a series of reflection minima appear in reflection spectra. Numerical simulations revealed that the structure can support two types of surface modes: surface plasmon-polaritons bound at the metallic surface and guided modes confined to the array of latex spheres, or their hybrids. Both experimental and theoretical results indicated that these surface modes show well-defined band structures due to the introduced periodicity by the monolayer array of latex spheres.     

First-principles calculations of carbon nanotubes adsorbed on Si(001)

We report first-principles calculations on the adsorption of a metallic (6,6) single-walled carbon nanotube (SWCN) on the Si(001) surface. We find stable geometries for the nanotube between two consecutive dimer rows where C-Si chemical bonds are formed. The binding energy in the most stable geometry is found to be 0.2 eV/A. Concerning the electronic properties, the most stable structure shows an increase in the density of states near the Fermi level due to the formation of C-Si bonds enhancing the metallic character of the nanotube by the contact with the surface. These properties may lead one to consider metallic SWCNs adsorbed on Si substrates for interconnections and contacts on future nanoscale devices. Finally, the nature of the nanotube-surface interaction for nanotubes of larger diameters is also discussed.     

Cluster self-organization of nanotubes in a nematic phase: The percolation behavior and appearance of optical singularities

The structural features, as well as the optical and electrophysical properties of a 5CB nematic liquid crystal with additions of multilayer carbon nanotubes, have been investigated in the concentration range C = 0.0025–0.1 wt %. The self-aggregation of nanotubes into clusters with a fractal structure occurs in the liquid crystal. At 0.025 wt %, the clusters are merged, initiating the percolation transition of the composite to a state with a high electric conductivity. The strong interaction of 5CB molecules with the surface of nanotube clusters is responsible for the formation of micron surface liquid crystal layers with an irregular field of elastic stresses and a complex structure of birefringence. They are easily observed in a polarization microscope and visualize directly invisible submicron nanotube aggregates. Their transverse size increases when an electric field is applied to the liquid crystal cell. Two mechanisms of the generation of optical singularities in the passing laser beam have been revealed. Optical vortices appear in the speckle fields of laser radiation scattered at the indented boundaries of the nanotube clusters, whereas the birefringence of the beam in surface liquid-crystal layers is accompanied by the appearance of polarization C points.     

Chemically shortened multi-walled carbon nanotubes used as anode materials for lithium-ion batteries

An easy chemically cutting process, modified Hummers' method, was proposed to treat multi-walled carbon nanotubes, successfully cutting pristine long, entangled carbon nanotubes into hydrosoluble pieces, mostly less than 200 nm. This short, chemically oxidized carbon nanotube was then applied as an anode material for lithium-ion batteries. The as-prepared material possessed higher reversible capacity and coulombic efficiency. The intrinsic factors were explored by X-ray photoelectron spectroscopy and cyclic voltammetry.     

Investigating interfacial contact configuration and behavior of single-walled carbon nanotube-based nanodevice with atomistic simulations

Carbon nanotubes (CNTs), including single-walled carbon nanotubes (SWNTs) and multi-walled carbon nanotubes (MWNTs), are considered to be the promising candidates for next-generation interconnects with excellent physical and chemical properties ranging from ultrahigh mechanical strength, to electrical properties, to thermal conductivity, to optical properties, etc. To further study the interfacial contact configurations of SWNT-based nanodevice with a 13.56-Å diameter, the corresponding simulations are carried out with the molecular dynamic method. The nanotube collapses dramatically into the surface with the complete collapse on the Au/Ag/graphite electrode surface and slight distortion on the Si/SiO₂ substrate surface, respectively. The related dominant mechanism is studied and explained. Meanwhile, the interfacial contact configuration and behavior, depended on other factors, are also analyzed in this article.     

Plasmonic interactions between a metallic nanotube array and a thin metallic film

Using the finite difference time domain (FDTD) method, we numerically simulate the plasmonic interactions and the optical properties of a metallic nanotube array near a thin metallic film. We show that the energies and intensities of the plasmon resonances depend strongly on the aspect ratio (the ratio of the inner to outer radius) of the nanotube, the separation between the center of the nanotube and the upper surface of the metallic film and the thickness of the film. In the thin film limit, the high-energy localized tube-related plasmons can induce their images on both sides of the metallic film, so the degeneracy state splits into two modes. Based on the nature of the field distribution, we also show clearly the plasmon resonant characteristics that the electromagnetic fields decay away from the surface of the nanotubes and both sides of the metallic film.     

碳纳米管网络导电特征的导电型原子力显微镜研究

利用导电型原子力显微镜对大范围碳纳米管（CNT）网络的导电性能进行成像观察.研究发现：在几十微米的成像范围内,每根CNT本身的电阻远小于CNT之间的接触电阻,以致于在电压偏置的网络中不同的CNT呈现电位不同的等位体;CNT的导电性能虽不因与其他CNT的交叠接触而改变,但是如果缠绕成束,则半导体性CNT趋于呈现金属性CNT的导电特征. 关键词： 导电型原子力显微镜 碳纳米管网络 碳管纳米电导