不同光聚焦状态的光击穿声辐射特性

强激光通过光学系统聚焦于水下时,击穿水介质辐射强声波信号.光学聚焦特性的不同,使得激光击穿区域形状的差异,导致辐射的声信号在强度、频谱特征上具有较大的差异性.为研究不同光聚焦状态对激光击穿形成的空泡辐射声波的影响,推导了不同聚焦状态下激光空泡壁的运动方程及声辐射模型,构建了激光声实验测量系统,实验研究了不同聚焦状态下光击穿导致的空泡脉动参数、辐射声信号特征的差异性.结论:激光声信号强度与激光能量成线性关系,在激光能量高于一定参数情况下,声信号强度变化不大;在低激光功率下,扩束聚焦与非扩束聚焦,辐射的声信号特性差异不大;在高激光功率条件,扩束聚焦击穿形成的空泡半径大于非扩束聚焦击穿,辐射的声信号强度高于非扩束聚焦;为提高激光击穿辐射卢信号效率,应对激光束进行扩束聚焦.     

聚焦泵浦条件下固体介质中受激布里渊散射过程的数值研究

 在非线性光学耦合波方程组中加入聚焦项，使之能够描述聚焦泵浦条件下的受激布里渊散射过程（SBS）。利用改进的SBS方程组，模拟了聚焦泵浦条件下熔石英玻璃棒中的SBS过程，给出了SBS反射率与泵浦激光能量的依赖关系，发现散射光脉冲中存在“聚焦刺”，并通过分析SBS诱导产生的应力场的特征对布里渊介质的安全性进行了评估，理论分析的结果与Yoshida等人的实验结果一致。     

块状介质超连续谱相位的相干特性

 块状介质超连续谱由一系列复杂的非线性过程产生。用两路飞秒泵浦光聚焦到熔石英玻璃上得到两束独立的超连续谱，实验上观察到它们形成的稳定干涉条纹；改变两路泵浦光的时间延迟，得到共线超连续谱形成的频率梳。实验证明，块状介质超连续谱的产生保持了泵浦光的相位锁定关系，泵浦光能量抖动和介质的缺陷都不会对超连续谱的相位带来明显的扰动。     

菲涅耳阵在固体中所产生的声束聚焦和扫描特性

用固体表面上的菲涅耳换能器阵实现固体中声束的聚焦和扫描,它具有实用意义。本文将分别运用标量和矢量理论,分析菲涅耳阵在固体中产生的声束特性。理论与实验结果进行了比较。最后,基于射频频谱分析的角度,对聚焦束的建立时间和加权技术进行了研讨。 关键词：     

共轴抛物镜线聚焦性能的2维分析

 掠入射泵浦方式作为一种全新的X射线激光泵浦方式，采用了共轴抛物镜作为线聚焦器件。利用2维光路追踪程序，计算了高斯光束从5°掠入射角增加到7°时入射到共轴抛物镜上的线聚焦效果。研究发现，掠入射角从5°增加到7°过程中，线聚焦的尺寸随着掠入射角变大,线聚焦长度从6 mm逐渐变长到12 mm,线聚焦宽度从150 μm变到40 μm；掠入射角6.5°～7°可以实现符合实验要求的线聚焦效果，线聚焦尺寸约10 mm×20 μm(最小线聚焦宽度)，7°掠入射可以实现较好的线聚焦，基本满足实验的要求。     

10MeV LIA强流电子束的聚焦

 研究了10MeV直线感应加速器（LIA）的输出束在螺线管透镜作用下的聚焦特性。通过解非线性电子轨迹方程获得实验所需的磁场范围，并解析分析空间电荷效应、发射度、透镜球面像差和色散像差对最小焦斑直径的限制，同时，对束质心螺旋运动影响束聚焦的情况亦做了较为详细的分析。实验结果表明：在合适的螺线管聚焦磁场下，可获得直径≤6mm的电子束焦斑，与理论分析结果基本一致。     

利用交变极性聚焦磁场抑制束质心的Corbcrew运动

提出可以利用交变极性磁场聚焦抑制Corkscrew运动，一方面可以抑制束脉冲顶部Corkscrew振荡的幅度，并提高电子束打靶位置的稳定性；另一方面通过聚焦布局的精心设计，可剔除束脉冲前后沿能散度较大的束流。数值计算结果表明，在采用交变周期为0．81m、峰值磁场设为0．2T，对能量为11．2MeV的电子束，当聚焦布局长为2．5m时，束质心位移从5mlTl(始端)被抑制至趋近于0(终端)。实验时，采用了数值计算相近的聚焦布局。     

汞蒸汽中利用四波和频产生125nm附近可调谐真空紫外激光

以氩为匹配气体的汞蒸汽四波和频实验中,一束泵浦光(ω₁)与汞原子6¹S₀—7¹S₀严格双光子共振,当另一束泵浦光(ω₃)在汞原子7¹S₀—9¹P₁跃迁的蓝端调频时,产生可调谐的真空紫外(VUV)激光(ω₄=2ω₁+ω₃),其 关键词：     

强流电子束聚焦数值模拟

采用粒子模拟（PIC）方法模拟了强流电子束在薄磁透镜中的聚焦。建立了强流电子束的聚焦模型,模拟了神龙一号加速器某次实验的结果,得到的模拟结果非常接近实验值,证明采用建立的PIC模型模拟强流束经过磁透镜时的聚焦是可信的。应用此模型模拟了电子束参数（入射半径、发射度、能散度、相位角等）对焦斑直径的影响, 结果表明:在模拟条件下,电子束平行入射时最佳束包络半径位于20.0~22.5 mm;发射度和能散度对焦斑直径的影响和理论公式吻合得较好;只有入射电子束包络半径和相位角匹配时才能得到小的焦斑直径。     

超导透镜及其聚焦行为

 理论上分析了利用高温超导体作为透镜聚焦强流相对论电子束的机理。实验研究中，研制出的YBa₂Cu₃O₇-d 高温超导体作为透镜的传输和聚焦性能被得到验证，结果表明，超导透镜具有明显的聚焦效果，并可有效控制束流强度分布，使被聚焦电子在束横截面上的分布更为均匀。     

RF离子源引出特性的研究

 为了使RF离子源具有良好的引出特性，测试了吸极几何参数、振荡器板压和引出电压对离子源聚焦度的影响，对实验结果进行了分析。在其它参数不变的情况下，吸极的外径D与内径d之比存在最佳值，增加D/d，有利于过聚焦的离子束恢复聚焦状态。吸极的长度为L，石英套管比吸极长l。当l/D增大时，聚焦度上升，引出束流下降。L/d之比减小时，聚焦度增大。当L/d小于4时，聚焦度增加趋势变缓。综合考虑聚焦度、引出束流和气压，D/d，l/D，L/d适宜的选择范围分别为1.6～2.1，0.7～1.1,4～7。增加振荡器功率会使离子束呈弱聚焦，而增加引出电压会使离子束呈过聚焦。振荡器功率和引出电压都存在最佳值。     

Control of Beam Halo-Chaos for an Intense Charged-Particle Beam Propagating Through Double Periodic Focusing Field by Soliton

We study an intense beam propagating through the double periodic focusing channel by the particle-core model, and obtain the beam envelope equation. According to the Poincare-Lyapunov theorem, we analyze the stability of beam envelope equation and find the beam halo. The soliton control method for controlling the beam halo-chaos is put forward based on mechanism of halo formation and strategy of controlling beam halo-chaos, and we also prove the validity of the control method, and furthermore, the feasible experimental project is given. We perform multiparticle simulation to control the halo by using the soliton controller. It is shown that our control method is effective. We also find the radial ion density changes when the ion beam is in the channel, not only the halo-chaos and its regeneration can be eliminated by using the nonlinear control method, but also the density uniformity can be found at beam＇s centre as long as an appropriate control method is chosen.     

四注行波管周期永磁聚焦系统的优化设计

根据电子注参数、布里渊磁场公式及周期聚焦系统轴向磁通密度峰值经验公式,计算出永磁聚焦系统轴向峰值磁通密度,利用Ansoft Maxwell 3D软件建立了四注行波管周期永磁聚焦系统仿真模型,对模型结构尺寸进行了参数化分析,研究了周期永磁聚焦系统结构尺寸对聚焦系统通道内磁通密度的影响,确定了磁聚焦系统结构最佳尺寸配合,优化设计出了四注行波管周期永磁聚焦系统。其电子注通道中心轴线上轴向磁通密度峰值B_z=309 mT,横向磁通密度B_t=2.86 mT,B_t/B_z=0.92%。     

Kirkpatrick–Baez mirrors to focus hard X‐rays in two dimensions as fabricated,tested and installed at the Advanced Photon Source

The micro‐focusing performance for hard X‐rays of a fixed‐geometry elliptical Kirkpatrick–Baez (K–B) mirrors assembly fabricated, tested and finally implemented at the micro‐probe beamline 8‐BM of the Advanced Photon Source is reported. Testing of the K–B mirror system was performed at the optics and detector test beamline 1‐BM. K–B mirrors of length 80 mm and 60 mm were fabricated by profile coating with Pt metal to produce focal lengths of 250 mm and 155 mm for 3 mrad incident angle. For the critical angle of Pt, a broad bandwidth of energies up to 20 keV applies. The classical K–B sequential mirror geometry was used, and mirrors were mounted on micro‐translation stages. The beam intensity profiles were measured by differentiating the curves of intensity data measured using a wire‐scanning method. A beam size of 1.3 µm (V) and 1.2 µm (H) was measured with monochromatic X‐rays of 18 keV at 1‐BM. After installation at 8‐BM the measured focus met the design requirements. In this paper the fabrication and metrology of the K–B mirrors are reported, as well as the focusing performances of the full mirrors‐plus‐mount set‐up at both beamlines.     

Numerical simulation and design of a thermionic electron gun

This paper reports the simulation of an electron gun. The effects on the beam quality of some parameters on the beam quality were studied and optimal choices were identified. It gives numerical beam qualities for a common electrostatic triode gun, and the dependencies on design parameters such as electrode geometries and bias voltages to these electrodes are shown. An electron beam of diameter 5 mm with energy of 5 ke V was assumed for the simulation process. Some design parameters were identified as variable parameters in the presence of space charge.These parameters are the inclination angle of emission electrode, the applied voltage to the focusing electrode, the gap width between the emission electrode and the focusing electrode and the diameter of the focusing electrode. The triode extraction system is designed and optimized by using CST software(for Particle Beam Simulations). The physical design of the extraction system is given in this paper. From the simulation results, it is concluded that the inclination angle of the emission electrode is optimized at 22.5?, the applied voltage to the focusing electrode was optimized and found to be Vfoc =-600 V, the optimal separation distance(gap between emission electrode and focusing electrode) is 4 mm, and the optimal diameter of the emission electrode is 14 mm. Initial results for these efforts aimed at emittance improvement are also given.     

光束束宽对自散焦介质中诱导光束聚焦的影响

影响自散焦介质中诱导光束聚焦过程的方程参量和初始条件共有5个，即两光束波长比(方程参量)、抽运光和信号光的初始振幅、两光束初始束宽比和两光束中心初始间距。通过数值计算讨论了初始束宽比在不同初始光束间距和波长比情况下对信号光聚焦过程的影响，得到了信号光聚焦效果的最佳初始参量条件。从而实现了对影响自散焦介质中诱导光束聚焦过程5个参量的完整详细研究。     

Electeostatic equilibrium of a modulated electron beam in a magnetoactive plasma

The two-dimensional (axisymmetric) equilibrium of a modulated electron beam (sequence of bunches) in a magnetoactive plasma under resonance conditions, when the frequency of modulation of the beam _M is close to (less than) the plasma frequency _p, is studied. The field of the collective electrostatic wave, focusing the bunches, is compensated by the thermal repulsion of the beam electrons. Based on the solutions obtained, it is established that the external magnetic field has a twofold effect on the equilibrium beam: first, to a weakening of the radial component of the focusing field because of the appearance of anisotropy in the dielectric permittivity tensor of the plasma and, second, an additional radial focusing of the bunches when they are rotated by the Lorentz force. The regions of the beam and plasma parameters in which one or another of the indicated effects predominates are determined and the conditions for the predominance of magnetic over electrostatic focusing are found.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 3, pp. 3–8, March, 1985.The author thanks V. B. Krasovitskii for proposing the subject and for constant interest in this work.     

Beam dynamics studies in the driver LINAC pre-stripper section of the RIA facility

The RIA facility driver LINAC consists of about 400 superconducting (SC) independently phased rf cavities. The LINAC is designed to accelerate simultaneously several charge-state beams to generate as much as 400 kW of uranium beam power. The LINAC beam dynamics is most sensitive to the focusing and accelerating structure parameters of the pre-stripper section, where the uranium beam is accelerated from 0.17 keV/u to 9.4 MeV/u. This section is designed to accept and accelerate two charge states (28 and 29) of uranium beam from an ECR ion source. The pre-stripper section must be designed to minimize the beam emittance distortion of this two-charge-state beam. In particular, the inter-cryostat spaces must be minimized and beam parameters near transitions of the accelerating and focusing lattices must be matched carefully. Several sources of possible effective emittance growth are considered in the design of the pre-stripper section and a tolerance budget is established. Numerical beam dynamics studies include realistic electric and magnetic three-dimensional field distributions in the SC rf cavities and SC solenoids. Error effects in the longitudinal beam parameters are studied.     

自散焦介质中光束聚焦的最佳参数选择

对自散焦介质中由交叉相位调制效应引发的光束聚焦过程进行了细致的系统研究,讨论了抽运光初始振幅、抽运光信号光初始间距和抽运光信号光波长比三个参量对信号光聚焦过程的影响.数值模拟结果表明:抽运光越强,信号光聚焦程度越大;抽运光信号光初始间距和抽运光信号光波长比均存在一个最佳值,使得光束聚焦达到最佳效果.通过参数最佳值的选择,可提高光束聚焦的效率 关键词： 非线性折射率系数 交叉相位调制效应 自散焦介质 光束聚焦     

椭圆高斯光束在自散焦介质中的诱导聚焦

研究了在自散焦介质中诱导光束聚焦过程中椭圆高斯光束对光束聚焦的影响。通过数值计算讨论了在不同初始抽运光束振幅、初始光束间距和波长比情况下椭圆高斯光束对信号光束聚焦的影响。影响光束聚焦过程的方程参量和初始条件共有6个,即两光束波长比(方程参量)、抽运光束和信号光束的初始振幅、两光束初始中心间距和两光束X、Y初始束宽比。采用此理论模型验证了Hickmann在1992年得出的实验结果,数值计算结果表明理论结果能够和实验结果定量地吻合。