Structural and electrical transport properties of Nb-doped TiO2 films deposited on LaAlO3 by rf sputtering

We have investigated the structural and electrical transport properties of Nb-doped TiO₂ films deposited on (1 0 0) LaAlO₃ substrates by rf magnetron sputtering at temperatures ranging from 873 K to 1073 K. Films deposited below 998 K are anatase, and mixed phases between anatase and rutile exist in the film grown at higher temperatures. We find that films deposited at low temperatures exhibit semiconductor behavior, while metallic conductivity is observed in the most conducting film deposited at 998 K. For this sample, compared to electron-phonon scattering mechanism, electron-phonon-impurity interference effect plays an important role in its electron transport process. Moreover, the temperature coefficient of the resistivity for the film deposited at 1073 K is negative from 2 K to 300 K. The temperature dependence of resistivity for the film is described by ∼exp(b/T)^1/2 at temperatures from 80 K down to 30 K, and by the fluctuation induced tunneling model from 80 K to 300 K.     

Physical investigations on pulsed laser deposited nanocrystalline ZnO thin films

The nanocrystalline ZnO thin films were deposited by pulsed laser deposition on quartz and i-Si (100) substrates at different substrate temperatures (473 K–873 K) and at different mixed partial pressures (0.05, 0.01, and 0.5 mbar) of Ar+O₂. The structural studies from XRD spectra reveals that the films deposited at 0.05 mbar and at lower substrate temperatures were c-axis oriented with predominant (002) crystallographic orientation. At 873 K along with (002) orientation, additional crystallographic orientations were also observed in case of films deposited at 0.01 and 0.5 mbar pressures. The composition of Zinc and Oxygen in ZnO films from EDAX reveals that the films deposited at lower partial pressures were have high at.% of O₂ whereas higher partial pressures and substrate temperatures had high at.% Zn. The surface microstructure of the films show that the films deposited at lower partial pressures (0.05 mbar ) and at lower substrate temperatures (473 K) were found to have nanoparticles of size 15 nm where as films deposited at 873 K have nanorods. The length of these nanorods increases with increasing Ar+O₂ partial pressure to 0.5 mbar. The optical energy gap of the film deposited at lower partial pressure and substrate temperature was 3.3 eV and decrease with the increase of substrate temperatures. The films deposited at 0.5 mbar and at 873 K emitted an intense luminescence at a wavelength of 390 nm. The measured thickness of deposited films by spectroscopic ellipsometry is around 456 nm.     

Structural and electrical properties of lithium manganese oxide thin films grown by pulsed laser deposition

LiMn₂O₄ thin films were deposited by reactive pulsed laser deposition technique and studied the microstructural and electrical properties of the films. The LiMn₂O₄ thin films deposited in an oxygen partial pressure of 100 mTorr and at a substrate temperature of 573 K from a lithium rich target were found to be nearly stoichiometric. The films exhibited predominantly (111) orientation representing the cubic spinel structure with Fd3m symmetry. The intensity of (111) peak increased and a slight shift in the peak position was observed with the increase of substrate temperature. The lattice parameter increased from 8.117 to 8.2417 Å with the increase of substrate temperature from 573 to 873 K. The electrical conductivity of the films is observed to be a strong function of temperature. The evaluated activation energy for the films deposited at 873 K is 0.64 eV.     

Role of columnar grain size in magnetization of La0.8MnO3 thin films grown by pulsed laser deposition

La_0.8MnO₃ thin films have been deposited on (100) SrTiO₃ substrates at different substrate temperatures by a pulsed laser deposition method. Electronic transport measurements show that a higher substrate temperature results in lower resistivity and higher insulator–metal transition temperature. Transmission electron microscope studies reveal that all the films exhibit a feature of columnar structure with the grain size decreasing with substrate temperature. We argue that the columnar grain size strongly affects the ferromagnetic transition temperature and, in turn, dominates the resistivity behavior. Based on this point, other effects, such as of annealing and film thickness, on the electronic properties are also discussed. PACS 68.55.Jk; 71.30.+h; 75.70.Ak; 75.70.Pa     

Lead-free ferroelectric thin films obtained by pulsed laser deposition

Na_0.5Bi_0.5TiO₃-BaTiO₃ (NBT-BT) thin films grown by pulsed laser deposition have been investigated by X-ray diffraction, scanning electron microscopy, and dielectric spectroscopy in order to clarify the role of substrate temperature on crystalline structure, grain morphology, and dielectric properties. We have shown that the structural and dielectric properties of NBT-BT thin films with composition at morphotropic phase boundary (6% BT) critically depend on the substrate temperature: small variations of this parameter induce structural changes, shifting the morphotropic phase boundary toward tetragonal or rhombohedral side. Higher deposition temperature (1000 K) favor the formation of rhombohedral phase, films deposited at 923 K and 973 K have tetragonal symmetry at room temperature. Grains morphology depends also on the deposition temperature. Atomic force micrographs show grains with square or rectangular shape in a compact structure for films grown at lower temperatures, while grains with triangular shape in a porous structure are observed for films grown at 1000 K. Dielectric spectroscopy measurements evidenced the phase transition between ferroelectric and antiferroelectric phase at 370 K. Films grown at 1000 K shown low electrical resistivity due to their porous structure. High dielectric constant values (about 800 at room temperature and 2700 at 570 K) have been obtained for films grown at temperatures up to 973 K.     

High temperature annealing effect on structure, optical property and laser-induced damage threshold of Ta2O5 films

Ta₂O₅ films were deposited by conventional electron beam evaporation method and then annealed in air at different temperature from 873 to 1273 K. It was found that the film structure changed from amorphous phase to hexagonal phase when annealed at 1073 K, then transformed to orthorhombic phase after annealed at 1273 K. The transmittance was improved after annealed at 873 K, and it decreased as the annealing temperature increased further. The total integrated scattering (TIS) tests and AFM results showed that both scattering and root mean square (RMS) roughness of films increased with the annealing temperature increasing. X-ray photoelectron spectroscopy (XPS) analysis showed that the film obtained better stoichiometry and the O/Ta ratio increased to 2.50 after annealing. It was found that the laser-induced damage threshold (LIDT) increased to the maximum when annealed at 873 K, while it decreased when the annealing temperature increased further. Detailed damaged models dominated by different parameters during annealing were discussed.     

Structural and luminescent characteristics of pulsed laser deposited Eu3+-doped Y2O3 thin films

Thin films of Eu-doped Y₂O₃ were deposited using the pulsed laser ablation technique on amorphous fused silica substrates. The effect of oxygen partial pressure (pO₂) and substrate temperature on the structural and optical characteristics of the deposited films were investigated. All the deposited films were crystalline, showing preferred orientation along the (111) plane, irrespective of oxygen partial pressure and substrate temperature. The film deposited at 0.005?mbar pO₂ exhibited better crystallinity with minimum FWHM at a substrate temperature of 600°C. All the films deposited at various substrate temperatures and different partial pressure (at 600°C) exhibited a red luminescence peak at 615?nm corresponding to the ⁵D₀–⁷F₁ transition in Eu³⁺. Photoluminescence excitation spectra exhibited two bands, one corresponding to band to band excitation (212?nm) of the host and the other to charge transfer band excitation (245?nm). A microstructure analysis revealed that surface roughness of the as-deposited films increases with increase in oxygen partial pressure.     

Characteristics of Ni films deposited on SiO2/Si(1 0 0) and MgO(0 0 1) by direct current magnetron sputtering system with the oblique target

280 nm-thick Ni films were deposited on SiO₂/Si(1 0 0) and MgO(0 0 1) substrates at 300 K, 513 K and 663 K by a direct current magnetron sputtering system with the oblique target. The films deposited at 300 K mainly have a [1 1 0] crystalline orientation in the film growth direction. The [1 1 0]-orientation weakens and the [1 1 1]- and [1 0 0]-orientations enhance with increasing deposition temperature. The lattice constant of the Ni films is smaller than that of the Ni bulk, except for the film grown on MgO(0 0 1) at 663 K. Furthermore, as the deposition temperature increases, the lattice constant of the films grown on the SiO₂/Si(1 0 0) decreases whereas that of the films grown on the MgO(0 0 1) increases. The films deposited at 300 K and 513 K grow with columnar grains perpendicular to the substrate. For the films deposited at 663 K, however, the columnar grain structure is destroyed, i.e., an about 50 nm-thick layer consisting of granular grains is formed at the interface between the film and the substrate and then large grains grow on the layer. The Ni films deposited at 300 K consist of thin columnar grains and have many voids at the grain boundaries. The grains become thick and the voids decrease with increasing deposition temperature. The resistivity of the film decreases and the saturation magnetization increases with increasing deposition temperature.     

沉积在α-Al２Ｏ3分形基底上Ag薄膜的特性

报道了采用磁控溅射法在α－Ａｌ_２Ｏ₃分形基底上沉积Ａｇ薄膜表面的形貌、结晶状态以及其Ｖ－Ｉ特性．结果表明：分形的Ａｌ_２Ｏ₃基底导致Ａｇ薄膜具有起伏不平的结构、较差的结晶状态并且存在大量的孔洞，它们同样受基底温度和薄膜厚度的影响．在一定的厚度范围内，Ａｇ薄膜呈现反常的非线性Ｉ（Ｖ）特性，其行为也受薄膜厚度、基底温度和测试环境的强烈影响． 关键词：     

Gas sensing properties of nanostructured MoO3 thin films prepared by spray pyrolysis

Thin films of molybdenum trioxide (MoO₃) were deposited on common glass using the chemical spray pyrolysis technique. A (NH₄)₆Mo₇O₂₄4H₂0 solution 0.1 M was used as the precursor one. The influence of substrate temperature on the crystallographic structure, surface morphology and electrical behavior of MoO₃ thin films was studied. MoO₃ can exist in two crystalline forms, the thermodynamically stable orthorhombic α-MoO₃ and the metastable monoclinic β-MoO₃ phase. XRD-spectra showed a growth of α-MoO₃ phase percentage as substrate temperature increases from 420 K up to 670 K. Films deposited in the 500–600 K range have a clearly porous surface structure of nanometer order as can be seen in SEM images. Changes up to six magnitude orders were observed in MoO₃ thin films electrical resistance when films temperature varied from 100 K up to 500 K. The sensing property of these MoO₃ films was also studied. The sensitivity was investigated in the temperature range 160 and 360 K for H₂O and CO gases, respectively. Both of them are of reducing nature. In all studied cases sensitivity decreases slowly as film temperature is raised. At room temperature the sensitivity changes from 12 up to 75% depending on substrate temperature. The sensitivity for CO gas was found to be lower than that of H₂O.     

Effects of deposition temperature and thickness on the structural properties of thermal evaporated bismuth thin films

Bismuth (Bi) thin films of different thicknesses were deposited onto Si(1 0 0) substrate at various substrate temperatures by thermal evaporation technique. Influences of thickness and deposition temperature on the film morphologies, microstructure, and topographies were investigated. A columnar growth of hexahedron-like grains with bimodal particle size distribution was observed at high deposition temperature. The columnar growth and the presence of large grains induce the Bi films to have large surface roughness as evidenced by atomic force microscopy (AFM). The dependence of the crystalline orientation on the substrate temperature was analyzed by X-ray diffraction (XRD), which shows that the Bi films have completely randomly oriented polycrystalline structure with a rhombohedral phase at high deposition temperature (200 °C) and were strongly textured with preferred orientation at low deposition temperatures (30 and 100 °C).     

Growth,structure, and thermal stability of epitaxial BaTiO3 films on Pt(111)

The growth of epitaxial ultrathin BaTiO₃ films upon rf magnetron sputter deposition on a Pt(111) substrate has been studied by scanning tunnelling microscopy, low-energy electron diffraction, and X-ray photoelectron spectroscopy. The BaTiO₃ films have been characterized from the initial stages of growth up to a film thickness of 4 unit cells. The deposited films develop a long-range order upon annealing at 1050 K in UHV. In the submonolayer regime a wetting layer is formed on Pt(111). Thicker films reveal a Stranski–Krastanov-like structure as observed with STM. By XPS a good agreement of the thin film stoichiometry with BaTiO₃ single crystal data is determined. Due to annealing at 1150 K BaTiO₃ forms large two-dimensional islands on the Pt(111) substrate. Different surface structures develop on the islands depending on the O₂ partial pressure during annealing.     

Microstructural and optical properties of nanocrystalline undoped zirconia thin films prepared by pulsed laser deposition

The zirconium oxide (ZrO₂) thin films are deposited on Si (100) and quartz substrates at various substrate temperatures (room temperature–973 K) at an optimized oxygen partial pressure of 3×10^?2 mbar using pulsed laser deposition technique. The effect of substrate temperature on microstructural, optical and mechanical properties of the films is investigated. The X-ray diffraction studies show that the films deposited at temperatures ≤773 K are monoclinic, while the films deposited at temperatures ≥873 K show both monoclinic and tetragonal phases. Tetragonal phase content increases with the increase of substrate temperatures. The surface morphology and roughness are investigated using atomic force microscope in contact mode. The optical properties of the films show that the refractive indices (at 550 nm) are found to increase from 1.84 to 2.35 as the temperature raises from room temperature (RT) to 973 K. Nanoindentation measurements show that the hardness of the films is 11.8 and 13.7 GPa for the films deposited at 300 and 973 K, respectively.     

Growth,electronic properties and thermal stability of the Fe/Al2O3 interface

Soft X-ray photoelectron spectroscopy and resonant photoemission have been used to study the growth and electronic properties of Fe ultrathin films deposited on Al₂O₃ substrates. A simultaneous multilayer growth mode has been found for Fe growth at room temperature. For iron coverages below 1 ML, Fe²⁺ species are formed at the Fe/Al₂O₃ interface, followed by the formation of a metallic iron overlayer. The bonding of Fe at very low coverages occurs by charge transfer from Fe to surface oxygen atoms, and neither hybridisation of Fe and Al states nor reduction of the Al₂O₃ substrate are observed. The thermal stability of the interface has been also studied in the range 673–873 K. Annealing produces Fe agglomeration in such a way that some areas of the Al₂O₃ substrate become fully Fe-depleted. In these Fe-depleted areas, Fe²⁺ completely disappears and Al⁰ reduced species are formed. This behaviour would explain the decrease in the magnetoresistance performance of magnetic tunnel junctions after annealing above 573 K.     

Giant temperature coefficient of resistance in Co-doped ZnO thin films

A novel high-performance thermistor material based on Co-doped ZnO thin films is presented. The films were deposited by the pulsed laser deposition technique on Si (111) single-crystal substrates. The structural and electronic transport properties were correlated as a function of parameters such as substrate temperature and Co-doped content for Zn_1?x Co _x O (x=0.005,0.05,0.10 and 0.15) to prepare these films. The Zn_1?x Co _x O films were deposited at various substrate temperatures between 20 and 280 °C. A value of 20 %/K for the negative temperature coefficient of resistance (TCR) with a wide range near room temperature was obtained. It was found that both TCR vs. temperature behavior and TCR value were strongly affected by cobalt doping level and substrate temperature. In addition, a maximal TCR value of over 20 %?K^?1 having a resistivity value of 3.6 Ω?cm was observed in a Zn_0.9Co_0.1O film near 260 °C, which was deposited at 120 °C and shown to be amorphous by X-ray diffraction. The result proved that the optimal Co concentration could help us to achieve giant TCR in Co-doped ZnO films. Meanwhile, the resistivities of the films ranged from 0.4 to 270 Ω?cm. A Co-doped ZnO/Si film is a strong candidate of thermometric materials for non-cooling and high-performance bolometric applications.     

Enhanced temperature-independent magnetoresistance below the metal-insulator transition temperature of epitaxial La0.2Nd0.4Ca0.4MnO3 thin films

Epitaxial La_0.2Nd_0.4Ca_0.4MnO₃ thin films have been deposited at 800°C on LaAlO₃ substrate using pulsed laser deposition technique. The structural and magnetotransport properties of the films have been studied. The sharp peak in the temperature dependence of the resistance corresponding to metal-to-insulator transition (T _p) has been observed at a temperature of T _p=82 K, 97 K and 110 K for 0 Oe, 20 kOe and 40 kOe magnetic fields, respectively. The film exhibits a large nearly temperature-independent magnetoresistance around 99% in the temperature regime below T _p. The zero field-cooled (ZFC) and field-cooled (FC) magnetization data at 50 Oe shows irreversibility between the ZFC and FC close to the ferromagnetic transition temperature T _c=250 K. The ZFC temperature data of the film displays ferromagnetic behavior for higher temperature regime T _c=250 K>T>T _p=82 K, and a decrease in magnetization with decreasing temperature up to 5 K below 82 K exhibiting a sort of antiferromagnetic behavior in the low temperature regime (T<82 K=T _p=T _N).     

Preparation of heat treated Ni2MnGa thin film without silicon diffusion

The Ni₂MnGa ferromagnetic alloys are one of these smart materials, that show a great interest for micro-electromechanical systems (MEMS) and micro-opto-electromechanical systems (MOEMS) when they are deposited as a thin film by rf sputtering. These films can be sputtered on silicon wafer in order to be easily integrated in Si-based device. Indeed, the use of this kind of substrate is very interesting because of the several well-known micromachining and integration technologies. However only heat treated thin films shows good functional properties that lay the problem of the silicon diffusion, as usually observed in the literature. In this work, a process (rf-sputtering process and annealing treatment) is proposed to elaborate martensite Ni₂MnGa thin films on Si substrate without silicon diffusion. This paper presents results on samples annealed at 873 K during 6 h.     

Improved dielectric properties of (Pb,Ca)TiO3 thin films prepared by metal-organic decomposition method

(Pb,Ca)TiO₃ (PCT) thin films have been deposited on Pt/Ti/SiO₂/Si substrate by metal-organic decomposition (MOD) technique. The film processing parameters such as drying and annealing temperatures have been optimized to obtain good-quality PCT films. Compositional analysis of the film has been studied by X-ray photoelectron spectroscopy (XPS). The effect of the annealing temperature on the crystalline structure, microstructure and electrical properties have been investigated by X-ray diffraction, atomic force microscopy (AFM) and impedance analyzer, respectively. Amorphous PCT films form at 350 °C and crystallize in the perovskite phase following the isothermal annealing at ?650 °C for 3 h in oxygen ambient. Typical tetragonal structure of the PCT film is evidenced from X-ray diffraction pattern. The grain size in the PCT films increases with an increase in annealing temperature. Significant improvement in the dielectric constant value is observed as compared to other reported work on PCT films. The observed dielectric constant and dissipation factor at 100 kHz for 650 °C annealed PCT films are 308 and 0.015, respectively. The correlation of the film microstructural features and electrical behaviors is described.     

Pulsed laser deposition of Pb(Zr0.52Ti0.48)O3 thin film on cobalt ferrite nano-seed layered Pt(111)/Si substrate: effect of oxygen pressure

The effect of oxygen pressure during pulsed laser deposition of Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films on CoFe₂O₄ nano-seed layered Pt(111)/Si substrate was investigated. The PZT film deposited at oxygen pressure lower than 25 mTorr is identified as both perovskite and pyrochlore phases and the films deposited at high oxygen pressure (50-100 mTorr) show the single-phase perovskite PZT that has a perfect (111)-orientation. In addition, the film deposited at P_O2 of 50 mTorr has a uniform surface morphology, whereas the film deposited at P_O2 of 100 mTorr has a non-uniform surface morphology and more incompacted columnar cross-section microstructure. The polarization of film deposited at 100 mTorr is higher than that deposited at 50 mTorr, but shift of the hysteresis loop along the electrical field axis in the film deposited at P_O2 of 100 mTorr is larger than that of the film deposited at P_O2 of 50 mTorr.     

Microstructural, optical and spectroscopic studies of laser ablated nanostructured tantalum oxide thin films

Thin films of tantalum oxide (Ta₂O₅) have been prepared by pulsed laser deposition technique at different substrate temperatures (300-973 K) under vacuum and under oxygen background (pO₂ = 2 × 10⁻³ mbar) conditions. The films are annealed at a temperature of 1173 K. The as-deposited films are amorphous irrespective of the substrate temperature. XRD patterns show that on annealing, the films get crystallized in orthorhombic phase of tantalum pentoxide (β-Ta₂O₅). The annealed films deposited at substrate temperatures 300 K and 673 K have a preferred orientation along (0 0 1) plane, whereas the films deposited at substrate temperatures above 673 K show a preferred orientation along (2 0 0) crystal plane. The deposited films are characterized using techniques such as grazing incidence X-ray diffraction (GIXRD), atomic force microscopy (AFM), micro-Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy and UV-visible spectroscopy. FTIR and micro-Raman measurements confirm the presence of Ta-O, Ta-O-Ta and O-Ta-O bands in the films. Grain size calculations from X-ray diffraction and AFM show a decrease with increase in substrate temperature. The variation of transmittance and band gap with film growth parameters are also discussed.