Ignition delay measurements of four component model gasolines exploring the impacts of biofuels and aromatics

This study explores the impacts of combinations of biofuel (ethanol, isobutanol and 2-methyl furan) and aromatic (toluene) compounds in a four component fuel blend, at fixed research octane number (RON) on ignition delay measured in an advanced fuel ignition delay analyzer (AFIDA 2805). Ignition delay measurements were performed over a range of temperatures from 400 to 725 °C (673 to 998 K) and two chamber pressures of 10 and 20 bar. The four component mixtures are compared to primary reference fuels at RON values of 90 and 100. The ignition delay measurements show that as the aromatic and biofuel concentrations increased, two stage ignition behavior was suppressed, at both initial chamber pressures. But both RON 100 (isooctane) and RON 90 reference fuels showed two stage ignition behavior, as did fuel mixtures with low biofuel and aromatic content. RON 90 fuels showed stronger two stage ignition behavior than RON 100 fuels, as expected. Depending on the type of biofuel in the mixture, the ignition delay at low chamber temperatures could be far greater than for the reference fuels. In particular, for the RON 100 mixtures at either 10 or 20 bar initial chamber pressure, the ignition delay at 400 °C (673 K) for the high level blend of 2-methyl furan and toluene (30 vol% of each) exhibited an ignition delay that was 10 times longer than for neat isooctane. The results show the strong non-linear octane blending response of these three biofuel compounds, especially in concert with the kinetic antagonism that toluene is known to display in mixtures with isooctane. These results have implications for the formulation of biofuel mixtures for spark ignition and advanced compression ignition engines, where this non-linear octane blending response could be exploited to improve knock resistance, or modulate the autoignition process.     

An improved detailed chemical kinetic model for C3-C4 linear and iso-alcohols and their blends with gasoline at engine-relevant conditions

Propanol and butanol isomers have received significant research attention as promising fuel additives or neat biofuels. Robust chemical kinetic models are needed that can provide accurate and efficient predictions of combustion performance across a wide range of engine relevant conditions. This study seeks to improve the understanding of ignition and combustion behavior of pure C3-C4 linear and iso-alcohols, and their blends with gasoline at engine-relevant conditions. In this work, a kinetic model with improved thermochemistry and reaction kinetics was developed based on recent theoretical calculations of H-atom abstraction and peroxy radical reaction rates. Kinetic model validations are reported, and the current model reproduces the ignition delay times of the C3 and C4 alcohols well. Variations in reactivity over a wide range of temperatures and other operating conditions are also well predicted by the current model. Recent ignition delay time measurements from a rapid compression machine of neat iso-propanol and iso-butanol [Cheng et al., Proc. Combust Inst. (2020)] and blends with a research grade gasoline [Goldsborough et al., Proc. Combust Inst. (2020)] at elevated pressure (20–40 bar) and intermediate temperatures (780–950 K) were used to demonstrate the accuracy of the current kinetic model at conditions relevant to boosted spark-ignition engines. The effects of alcohol blending with gasoline on the autoignition behavior are discussed. The current model captures the suppression of reactivity in the low-temperature and negative-temperature-coefficient (NTC) region when either isopropanol and isobutanol are added to a research grade gasoline. Sensitivity and reaction flux analysis were performed to provide insights into the relevant fuel chemistry of the C3-C4 alcohols.     

Autoignition of varied cetane number fuels at low temperatures

The reactivity of six kerosene based control fuels, specifically formulated for cetane number variation, are investigated by measuring ignition delay time in a heated rapid compression machine. Cetane numbers vary from 30 to 55 (increment of 5) while holding other properties relatively constant by adjusting chemical group composition. Main cetane variation was controlled through the distribution of normal alkanes and isoalkanes, which was fine-tuned using additives. Other fuel properties such as density, viscosity, H/C ratio, etc. were balanced using cyclic compounds and aromatics. Fuels were tested in the RCM at compressed pressures of P_c=?10 and 20?bar, equivalence ratios of ??=?0.25, 0.5 and 1.0, in the low to intermediate temperature range (620?K?≤?T_c?≤?730?K). Relations between cetane number and ignition delay time have been evaluated at multiple test conditions, and further analysis on multistage ignition has been conducted. Ignition delay times of fuels with higher cetane numbers are shorter at these temperatures for most conditions. First stage ignition delay time measurements have been observed to be relatively insensitive to P_c, ?, and fuel type, while deviations in overall ignition delay times are mainly attributed to second stage ignition delay time, impacted by variations in the first stage temperature. Control fuels of this type offer an opportunity to be used in practical experiments to determine the impact of cetane number on combustion dynamics.     

An experimental and modeling study on autoignition of 2-phenylethanol and its blends with n-heptane

2-Phenylethanol (2-PE) is an aromatic alcohol with high research octane number, high octane sensitivity, and a potential to be produced using biomass. Considering that 2-PE can be used as a fuel additive for boosting the anti-knocking quality of gasoline in spark-ignition engines and as the low reactivity fuel or fuel component in dual-fuel reactivity controlled compression ignition (RCCI) engines, it is of fundamental and practical interest to understand the autoignition chemistry of 2-PE, especially at low-to-intermediate temperatures (<1000 K). Based upon the experimental ignition delay time (IDT) results of neat 2-PE obtained from our previous rapid compression machine (RCM) investigation and the literature shock tube study, a detailed chemical kinetic model of 2-PE is developed herein, covering low-to-high temperature regimes. Besides, RCM experiments using binary fuel blends of 2-PE and n-heptane (nC7) are conducted in this work to investigate the nC7/2-PE blending effects, as they represent a dual-fuel system for RCCI operations. Furthermore, the newly developed 2-PE model is merged with a well-validated nC7 kinetic model to generate the current nC7/2-PE binary blend model. Overall, the consolidated model reasonably predicts the experimental IDT data of neat 2-PE and nC7/2-PE blends, as well as captures the experimental effects of pressure, equivalence ratio, and blending ratio on autoignition. Finally, model-based chemical kinetic analyses are carried out to understand and identify the controlling chemistry accounting for the observed blending effects in RCM experiments. The analyses reveal that nC7 enhances 2-PE autoignition via providing extra ȮH radicals to the shared radical pool, while the diminished nC7 promoting effect on 2-PE autoignition with increasing temperature is due to the negative temperature coefficient characteristics of nC7.     

Effects of blending 2,5-dimethylfuran on the laminar burning velocity and ignition delay time of isooctane/air mixture

The prospects of 2,5-dimethylfuran (DMF) as a bio-derived fuel that can be blended with gasoline are believed to be impressive. However, the effects of blending DMF on the key combustion parameters like the laminar burning velocity and ignition delay time of gasoline/air mixture need to be studied extensively for the successful implementation of the fuel mixture in spark ignition engines. Therefore, a skeletal chemical kinetic mechanism, comprising of 999 reactions among 218 species, has been developed in the present work for this purpose. The proposed chemical kinetic model has been validated against a wide range of experimental data for the laminar burning velocity and ignition delay time of isooctane (representing gasoline), DMF and their blends. It has been found from the present study that the thermal diffusivity of the unburnt gas mixture changes by a very small amount from the corresponding value for the pure isooctane/air mixture when DMF is added. Unlike isooctane, the DMF molecule does not consume H radicals during its primary breakup. Therefore, the maximum laminar burning velocity increases marginally when 50% DMF is blended with isooctane due to the increased presence of H radicals in the flame. The negative temperature coefficient behaviour in the ignition delay time of the isooctane fuel vanishes when 30% DMF (v/v) is blended to it.     

不同重力环境下辐射加热材料表面着火特性分析

研究外界辐射加热下，不同重力环境中热薄燃料的着火特性．探讨了重力、环境氧浓度、环境压力及外界辐射强度对着火的影响．结果表明，随着重力的变化，存在不同的着火机制．在微重力和在高的环境氧浓度中，材料的着火延迟时间变短．压力减小，着火延迟时间增大．随着辐射强度的增大，着火延迟时间变小．     

Autoignition characteristics of bio-based fuels,farnesane and TPGME,in comparison with fuels of similar cetane rating

Bio-based alternative fuels have received increasing attention with growing concerns about depletion of fossil reserves and environmental deterioration. The development of new combustion concepts in internal combustion engines requires a better understanding of autoignition characteristics of the bio-based alternative fuels. This study investigates two cases of alternative fuels, namely, a kerosene-type fuel farnesane and an oxygenated fuel, TPGME, and compares those fuels with full-boiling range of fuels with similar cetane number. The homogeneous autoignition and spray ignition characteristics of the selected fuels are studied using a modified CFR octane rating engine and a cetane rating instrument, respectively. When comparing farnesane with a full-boiling range counterpart (HRJ8), their similar cetane ratings result in comparable combustion heat release, but the overall ignition reactivity of farnesane is stronger than HRJ8 during the pre-ignition process. Results from a constant volume spray combustion chamber indicate that the spray process of farnesane and HRJ8 strongly influences the overall ignition delay of each fuel. Despite the similar cetane ratings of TPGME and n-heptane, TPGME shows greater apparent low-temperature oxidation reactivity at low compression ratios in the range from CR 4.0-5.5 than n-heptane. A simplified model focused on the key reaction pathways of low-temperature oxidation of TPGME has been applied to account for the stronger low-temperature reactivity of TPGME, supported by density functional theory (DFT) calculations. Regardless of the similar cetane ratings of the fuels, n-heptane and JP-8/SPK lead to similar total ignition delay times, while TPGME shows the shortest overall ignition delay times in the constant volume combustion chamber.     

Combustion behavior of ammonia blended with diethyl ether

Ammonia (NH₃) is recognized as a carbon-free hydrogen-carrier fuel with a high content of hydrogen atoms per unit volume. Recently, ammonia has received increasing attention as a promising alternative fuel for internal combustion engine and gas turbine applications. However, the viability of ammonia fueling future combustion devices has several barriers to overcome. To overcome the challenge of its low reactivity, it is proposed to blend it with a high-reactivity fuel. In this work, we have investigated the combustion characteristics of ammonia/diethyl ether (NH₃/DEE) blends using a rapid compression machine (RCM) and a constant volume spherical reactor (CVSR). Ignition delay times (IDTs) of NH₃/DEE blends were measured using the RCM over a temperature range of 620 to 942 K, pressures near 20 and 40 bar, equivalence ratios (Φ) of 1 and 0.5, and a range of mole fractions of DEE, χ_DEE, from 0.05 to 0.2 (DEE/NH₃ = 5 – 20%). Laminar burning velocities of NH₃/DEE premixed flames were measured using the CVSR at 298 K, 1 bar, Φ of 0.9 to 1.3, and χ_DEE from 0.1 to 0.4. Our results indicate that DEE promotes the reactivity of fuel blends resulting in significant shortening of the ignition delay times of ammonia under RCM conditions. IDTs expectedly exhibited strong dependence on pressure and equivalence ratio for a given blend. Laminar burning velocity was found to increase with increasing fraction of DEE. The burnt gas Markstein length increased with equivalence ratio for χ_DEE = 0.1 as seen in NH₃-air flames, while the opposite evolution of Markstein length was observed with Φ for 0.1 < χ_DEE ≤ 0.4, as observed in isooctane-air flames. A detailed chemical kinetics model was assembled to analyze and understand the combustion characteristics of NH₃/DEE blends.     

Experimental and modeling study of the autoignition characteristics of commercial diesel under engine-relevant conditions

Knowledge of the autoignition characteristics of diesel fuels is of great importance for understanding the combustion performance in engines and developing surrogate fuels. Here ignition delays of China's stage 6 diesel, a commercial fuel, were measured in a heated rapid compression machine (RCM) under engine-relevant conditions. Gas-phase autoignition experiments were carried out at equivalence ratios ranging from 0.37 to 1.0, under compressed pressures of 10, 15, and 20?bar, and within a temperature range of 685–865?K. In all investigated conditions, negative temperature coefficient (NTC) behavior of the total ignition delays is observed. The autoignition of the diesel fuel exhibits pronounced two-stage characteristics with strong low-temperature reactivity. Experimental results indicate that the total ignition delays shorten with increasing compressed pressure, oxygen mole fraction and fuel mole fraction. The first-stage ignition delays are mainly controlled by compressed temperature and also affected by oxygen mole fraction and compressed pressure but show a very weak dependence on fuel mole fraction. Correlations describing the first-stage ignition delay and the total ignition delay were proposed to further clarify the ignition delay dependence on the multiple factors. Additionally, it is found that the newly measured ignition delays well coincide with and complement the diesel ignition data in the literature. A recently developed diesel mechanism was used to simulate the diesel autoignition on the RCM. The simulation results are found to agree well the experimental measurements over the whole temperature ranges. Species concentration analysis and brute force sensitivity analysis were also conducted to identify the crucial species and reactions controlling the autoignition of the diesel fuel.     

An experimental investigation on spray, ignition and combustion characteristics of biodiesels

Spray, ignition and combustion characteristics of biodiesel fuels were investigated under a simulated diesel-engine condition (885 K, 4 MPa) in a constant volume combustion vessel. Two biodiesel fuels originated from palm oil and used cooking oil were used while JIS#2 used as the base fuel. Spray images were taken by a high speed video camera by using Mie-scattering method to measure liquid phase penetration and liquid length. An image intensifier combined with OH filter was used to obtain OH radical image near 313 nm. Ignition and combustion characteristics were studied by OH radical images. Biodiesel fuels give appreciably longer liquid lengths and shorter ignition delays. At low injection pressure (100 MPa), biodiesel fuels give shorter lift-off lengths than those of diesel. While at high injection pressure (200 MPa), the lift-off length of biodiesel fuel originated palm oil gives the shortest value and that of biodiesel from used cooking oil gives the longest one. Air entrainment upstream of lift-off length of three fuels was estimated and compared to soot formation distance. This study reveals that the viscosity and ignition quality of biodiesel fuel have great influences on jet flame structure and soot formation tendency.     

Effect of flash boiling injection on combustion and PN emissions of DISI optical engine fueled with butanol isomers/TPRF blends

Direct injection spark ignition (DISI) engines have been widely used in passenger cars due to their lower fuel consumption, better controllability, and high efficiency. However, DISI engines are suffering from wall wetting, imperfect mixture formation, excess soot emissions, and cyclic variations. Applying a new fuel atomization technique and using biofuels with their distinctive properties can potentially aid in improving DISI engines. In this research, the effects of isobutanol and 2-butanol and their blends with Toluene Primary Reference Fuel (TPRF) on spray characteristics, DISI engine combustion, and particle number (PN) emissions are investigated for conditions with and without flash boiling of the injected fuel. Spray characteristics are investigated using a constant volume chamber. Then, the combustion, flame propagation, and PN emissions are examined using an optical DISI engine. The fuel temperature is set to 298 K and 453 K for liquid injection and flash boiling injection, respectively. The tested blending ratio is 30 vol% butanol isomers and 70 vol% TPRF. The results of the spray test reveal that liquid fuel plumes are distinctly observed, and butanol blends show a slightly wider spray angle with lower penetration length compared to TPRF. However, under flash boiling injection, the sprays collapse towards the injector axis, forming a more extended single central vapor jet due to the plumes' interaction. Meanwhile, butanol blends yield a narrow spray angle with more extended penetration compared to TPRF. The flame visualization test shows that the flash boiling injection reduced yellow flames compared to liquid fuel injection, reflecting the improvements in mixture formation. Thus, improvements were noted in the heat release and PN emissions. Butanol addition reduced the PN emissions by 43% under regular liquid injection. Flash boiling injection provided an additional 25% reduction in PN emissions.     

High-pressure fuel spray ignition behavior with hot surface interaction

Fuel-flexible aircraft propulsion systems using compression ignition engines will require novel strategies for reducing the ignition delay of low-reactivity fuels to feasible timescales. Hot surface ignition of fuel sprays has been implemented in some practical situations, but the complex nature of flame formation within the spray structure poses significant challenges. In order to design next-generation ignition devices, the capacity of hot surface heating elements to promote fuel spray ignition must be investigated. In this study, a rapid compression machine (RCM) was used to examine the ignition process of a single kerosene-based F-24 jet fuel spray with a cylindrical heating element inserted into the spray periphery. The experiments, performed with moderately high injection pressures of 40 MPa, have demonstrated two modes of ignition governed by surface temperature and insertion depth of the heating element. There exists an optimal position where the heating element tip is located in the fuel vapor cone around the liquid spray. For this configuration, a critical surface temperature was identified (～1250 K), above which short ignition delays associated with a “spray ignition” mode are consistently achieved. In this case, a local ignition flame kernel propagates downstream to the flame lift-off length before full ignition of the spray. In comparison, below the critical temperature a slower “volumetric” mode results. The extended ignition delays associated with this mode may be impractical for compression ignition engines operating at high speeds and increased altitude.     

Comprehensive ignition characterization of a non-toxic hypergolic hybrid rocket propellant

This paper describes a comprehensive characterization of ignition properties of a metal-hydride based non-toxic hypergolic hybrid rocket propellant. The propellant consists of Rocket Grade Hydrogen Peroxide (RGHP) as oxidizer, high-density Polyethylene (HDPE) as fuel and sodium borohydride (NaBH₄) as the additive, embedded in the HDPE matrix. Ignition quality was characterized as ignition delay, ignition probability and flame spread. In a drop-test setup, ignition characteristics were determined as a function of seven parameters: RGHP concentration, additive loading, oxidizer droplet impact velocity, oxidizer droplet volume, pressure, diluent gas, and environmental exposure. The parameters encompass thermo-chemical, fluid/droplet dynamics and environmental factors affecting ignition. Ignition delays as low as 3 ms were observed, one of the lowest using non-toxic hypergolic hybrid propellants in open-air. An overwhelming majority of conditions tested yielded <10 ms ignition delays and 100% ignition success. All conditions tested affected ignition to varying degrees with RGHP concentration, NaBH₄ loading and drop impact velocity significantly affecting ignition. Further, contrary to expectations, exposing sanded fuel samples to humidity for a few h enhanced ignition instead of hampering it and exposure for 24 h did not lead to ignition degradation. Tests with diluent gases other than air (at atmospheric and elevated pressures) revealed that atmospheric oxygen played a negligible role in the reaction process. This proved that oxygen for the initial ignition event was obtained from RGHP decomposition, with atmospheric oxygen playing no role in ignition performance. Aside from demonstrating excellent ignition characteristics, our results further show a need to go beyond thermo-chemical properties and to consider aspects of ignition other than ignition delay in hypergolic propellant research to enable a complete understanding of the ignition processes. The comprehensive ignition characterization demonstrates the chosen propellant's ability to overcome ignition challenges in hybrid rockets and serves as a proof of concept for its further development.     

Understanding the synergistic blending octane behavior of 2-methylfuran

The autoignition kinetics of hydrocarbons is an important criterion for selecting fuels for piston reciprocating engines, and it can be determined by relative performance to mixtures of alkanes, n-heptane and iso-octane, under certain standardized operating conditions. 2-methylfuran is a potential biofuel candidate, whose autoignition chemistry is markedly different from alkanes. Its octane behavior when blended with paraffins also shows a marked difference. The blending octane behavior of a fuel is characterized by its Blending Octane Number (BON). The BON of 2-methylfuran was extensively characterized in this work. 2-methylfuran's BON was mapped from experimental ignition delay times measured in a constant volume combustion chamber using established correlations. The effect on BON was studied depending on the RON of the base fuel into which 2-methylfuran was blended, as well as the quantity of 2-methylfuran blended. BON of 2-methyfuran was greater than its RON by a factor of four or more for some blends studied. BON reduced with increasing RON of the base fuel, as well as with increasing quantity of 2-methylfuran blended. A chemical kinetic model was created by integration of well validated sub-models for the blend components, and then used to explain the chemical kinetics leading to the extremely high BON values of 2-methylfuran. The synergetic anti-knock blending effect of 2-methylfuran is partially due to its physical properties leading to a greater molar fraction per volume fraction in the blend compared to iso-octane. Analysis using chemical kinetic model revealed that the chemical action behind 2-methylfuran's blending octane behavior was due to its ability to quench OH radicals which are important to the low-temperature oxidation chemistry of alkanes. This quenching effect is achieved due to the more rapid reaction rate of 2-methylfuran with OH radical compared to iso-octane, followed by the immediate conversion of the adduct shifting the equilibrium towards the product.     

Numerical simulations of the ignition of n-heptane droplets in the transition diameter range from heterogeneous to homogeneous ignition

Spontaneous ignition of single n-heptane droplets in a constant volume filled with air is numerically simulated with the spherical symmetry. The volume is closed against mass, species, and energy transfer. The numerical model is fully transient. It continues calculation even after the droplet has completely vaporized, and therefore can predict pre-vaporized ignition. Initial pressure and initial air temperature are fixed at 3 MPa and 773 K, respectively. The droplet is initially at room temperature, and its diameter is between 1 and 100 μm. When the overall equivalence ratio is fixed to be sufficiently large, there exists no ignition limit in terms of initial droplet diameter d₀, and the ignition delay takes a minimum value at certain d₀. In such a case, transition from the heterogeneous ignition to the homogeneous ignition with decreasing d₀ is observed. When d₀ is fixed to be so small that the ignition would not occur in an infinite volume of air, the ignition delay takes a minimum value at certain , which is less than unity. Two-stage ignition behavior is investigated with this model. Ignition delay of a cool flame has the dependence on d₀ that is similar to that of ignition delay of a hot flame when is unity. When is almost zero, the ignition limit for cool flame in terms of d₀ is not identified unlike that for hot flame.     

Development of a reduced chemical kinetic mechanism for a gasoline surrogate for gasoline HCCI combustion

A reduced chemical kinetic mechanism consisting of 48 species and 67 reactions is developed and validated for a gasoline surrogate fuel. The surrogate fuel is modeled as a blend of iso-octane, n-heptane, and toluene. The mechanism reduction is performed using sensitivity analysis, investigation of species concentrations, and consideration of the main reaction path. Comparison between ignition delay times calculated using the proposed mechanism and those obtained from shock tube data show that the reduced mechanism can predict delay times with good accuracy at temperatures above 1000 K. The mechanism can also predict the two-stage ignition at the moment of ignition. A rapid compression machine (RCM) is designed to measure ignition delay times of gasoline and gasoline surrogates at temperatures between 890 and 1000 K. Our experimental results suggest that a new gasoline surrogate that has a different mixture ratio than previously defined surrogates is the most similar to gasoline. In addition, the reduced mechanism is validated for the RCM experimental conditions using CFD simulations.     

Effects of isoalcohol blending with gasoline on autoignition behavior in a rapid compression machine: Isopropanol and isobutanol

Alcohols, and particularly isoalcohols, are potentially advantageous blendstocks towards achieving efficient, low-carbon intensity internal combustion engines. Their use in advanced configurations, such as boosted spark-ignition or spark-assisted compression ignition, requires a comprehensive understanding of their blending effects on the low- and intermediate-temperature autoignition behavior of petroleum-derived gasoline. This work reports an experimental and modeling study of such autoignition characteristics quantified in a twin-piston rapid compression machine. Isopropanol and isobutanol are blended into a research-grade gasoline (FACE-F) at oxygenate blend levels of 0 to 30% vol/vol, with tests conducted at pressures of 20 and 40 bar, temperatures from 700 to 1000 K, and dilute stoichiometric fuel loadings. Changes to overall reactivity, including first-stage and main ignition times, and preliminary exothermicity are established, with comparisons made to previous measurements with ethanol-blended FACE-F gasoline.It is found that at low-temperature/NTC conditions (700–860 K) the isoalcohols suppress first-stage reactivity and associated heat release while main ignition times are extended. At NTC/intermediate-temperature (860–1000 K) conditions changes to fuel reactivity are less significant with isopropanol slightly suppressing reactivity and isobutanol promoting ignition. Detailed chemical kinetic modeling is used to interpret the experimental measurements. Overall trends of suppression or promotion in the blending behavior are reasonably captured by the model. Sensitivity and rate of production analyses indicate that at lower temperatures H-atom abstraction reactions from the surrogate fuel molecules (e.g., cyclopentane, isooctane) and the isoalcohols via ?H are important leading to TC3H6OH and IC4H8OH–C radicals, for isopropanol and isobutanol respectively, which act as scavengers in the system. At higher temperatures, similar chemistries are dominant, but there is an increasing importance of abstraction by HO₂. The kinetic modeling also indicates that the promoting effect of isobutanol at higher temperatures is due to the increased abstractions at the γ-sites, while at lower temperatures abstraction at the α-site leads to greater reactivity suppression.     

Nonpremixed ignition of H2/air in a mixing layer with a vortex

The ignition of a laminar non-premixed H₂/air mixing layer with an embedded vortex was computationally studied with detailed chemistry and transport. The initial vortex velocity and pressure fields were specified based on the stream function of an incompressible nonviscous vortex. The fuel side is pure hydrogen at 300 K, and the oxidizer side is air at 2000 K. The vortex evolution process was found to consist of two ignition events. The first ignition occurs in a diffusion mode with chain branching reactions dominating. The second ignition takes place in the premixed mode, with more chemical reactions involved, and is significantly affected by the heat and species generated in the first ignition event. The coupling between the most reactive mixture fraction and scalar dissipation rate was verified to be crucial to the ignition delay. The effects of the vortex strength, characteristic size, and its center location were individually investigated. For all vortex cases, the ignition delay was shorter than that of the 1D case. Furthermore, the ignition delay has a nonmonotonic dependence on all the vortex parameters.     

Application of an aerosol shock tube to the measurement of diesel ignition delay times

Shock tube ignition delay times were measured for DF-2 diesel/21% O₂/argon mixtures at pressures from 2.3 to 8.0 atm, equivalence ratios from 0.3 to 1.35, and temperatures from 900 to 1300 K using a new experimental flow facility, an aerosol shock tube. The aerosol shock tube combines conventional shock tube methodology with aerosol loading of fuel-oxidizer mixtures. Significant efforts have been made to ensure that the aerosol mixtures were spatially uniform, that the incident shock wave was well-behaved, and that the post-shock conditions and mixture fractions were accurately determined. The nebulizer-generated, narrow, micron-sized aerosol size distribution permitted rapid evaporation of the fuel mixture and enabled separation of the diesel fuel evaporation and diffusion processes that occurred behind the incident shock wave from the chemical ignition processes that occurred behind the higher temperature and pressure reflected shock wave. This rapid evaporation technique enables the study of a wide range of low-vapor-pressure practical fuels and fuel surrogates without the complication of fuel cracking that can occur with heated experimental facilities. These diesel ignition delay measurements extend the temperature and pressure range of earlier flow reactor studies, provide evidence for NTC behavior in diesel fuel ignition delay times at lower temperatures, and provide an accurate data base for the development and comparison of kinetic mechanisms for diesel fuel and surrogate mixtures. Representative comparisons with several single-component diesel surrogate models are also given.     

Ignition of cyclopropane in shock waves

The values of the ignition delay time of cyclopropane–oxygen–argon (cyclo-C₃H₆–O₂–Ar) mixtures of different compositions (φ = 0.333, 1, and 3) behind reflected shock waves at temperatures of 1200–1640 K and a pressure of (0.55 ± 0.05) MPa are measured. A kinetic mechanism of cyclopropane ignition using the known rate constants for the most important elementary reactions is developed. The mechanism closely describes both our own and published experimental data on the delay time of ignition of cyclopropane in shock waves over wide ranges of temperature (1200–2100 K), pressure (0.1–0.55 MPa), cyclopropane concentrations (0.05–11 vol %), and oxygen concentrations (0.25–21 vol %). It is shown that, with increasing fraction of diluent gas in the mixture, the dependence of the ignition delay time on the fuel-to-oxidizer equivalence ratio changes.