Autoignition of ethylene in shock waves

The delay time of ignition of various C₂H₄-O₂-Ar mixtures behind reflected shock waves were measured at temperatures of 1090–1520 K and a pressure of 0.65 ± 0.05 MPa. A kinetic scheme of the ignition of ethylene based on the known rate constants of the key elementary reactions was developed. The scheme satisfactorily describes our own and published data on the ignition of ethylene in shock waves over wide ranges of temperature (1100–2400 K), pressure (0.006–0.64 MPa) and ethylene (0.1–17.4 vol %) and oxygen (0.6–20.7 vol %) concentrations.     

Ignition of acetylene-oxygen mixtures behind shock waves

The delay time of ignition of C₂H₂-O₂-Ar mixtures of various compositions behind reflected shock waves were measured at 980–1300 K and 0.65 ± 0.05 MPa. A kinetic scheme of the ignition of acetylene based on the available rate constants of the key elementary reactions was developed. The scheme satisfactorily describes the experimental data from various works over wide temperature, pressure, and concentration ranges: 980–2400 K, 0.01–1.0 MPa, and 0.5–20.3 vol % acetylene and 1.25–20.4 vol% O₂.     

Ignition delay times of methyl oleate and methyl linoleate behind reflected shock waves

Ignition delay times for methyl oleate (C₁₉H₃₆O₂, CAS: 112-62-9) and methyl linoleate (C₁₉H₃₄O₂, CAS: 112-63-0) were measured for the first time behind reflected shock waves, using an aerosol shock tube. The aerosol shock tube enabled study of these very-low-vapor-pressure fuels by introducing a spatially-uniform fuel aerosol/4% oxygen/argon mixture into the shock tube and employing the incident shock wave to produce complete fuel evaporation, diffusion, and mixing. Reflected shock conditions covered temperatures from 1100 to 1400 K, pressures of 3.5 and 7.0 atm, and equivalence ratios from 0.6 to 2.4. Ignition delay times for both fuels were found to be similar over a wide range of conditions. The most notable trend in the observed ignition delay times was that the pressure and equivalence ratio scaling were a strong function of temperature, and exhibited cross-over temperatures at which there was no sensitivity to either parameter. Data were also compared to the biodiesel kinetic mechanism of Westbrook et al. (2011) [10], which underpredicts ignition delay times by about 50%. Differences between experimental and computed ignition delay times were strongly related to existing errors and uncertainties in the thermochemistry of the large methyl ester species, and when these were corrected, the kinetic simulations agreed significantly better with the experimental measurements.     

Reactions of initiation of the autoignition of H<Subscript>2</Subscript>–O<Subscript>2</Subscript> mixtures in shock waves

The initiation of the autoignition of hydrogen–oxygen–argon mixtures behind reflected shock waves is studied by absorption and emission spectrophotometry in the temperature range of 960 < T < 1670 K at pressures of ~0.1 MPa. Introduction of Mo(CO)₆ additive in an amount of ~80 ppm made it possible to study the effect of O atoms on the shortening of the ignition delay time of H₂–O₂–Ar mixtures. A kinetic modeling of our own and published experimental data at temperatures of 930 < T < 2500 K and pressures of 0.05 < P < 8.7 MPa enabled to establish how the initiation reactions influence the process of self-ignition and to evaluate the rate constant for one of the initiation reactions: k(H₂ + O₂ → 2OH) = (3 ± 1) × 10¹¹exp(–E _a/RT), cm³ mol^–1 s^–1, where E _a = (40 ± 2) kcal/mol.     

Experimental study and modeling of shock tube ignition delay times for hydrogen-oxygen-argon mixtures at low temperatures

Recent literature has indicated that experimental shock tube ignition delay times for hydrogen combustion at low-temperature conditions may deviate significantly from those predicted by current detailed kinetic models. The source of this difference is uncertain. In the current study, the effects of shock tube facility-dependent gasdynamics and localized pre-ignition energy release are explored by measuring and simulating hydrogen-oxygen ignition delay times. Shock tube hydrogen-oxygen ignition delay time data were taken behind reflected shock waves at temperatures between 908 to 1118 K and pressures between 3.0 and 3.7 atm for two test mixtures: 4% H₂, 2% O₂, balance Ar, and 15% H₂, 18% O₂, balance Ar. The experimental ignition delay times at temperatures below 980 K are found to be shorter than those predicted by current mechanisms when the normal idealized constant volume (V) and internal energy (E) assumptions are employed. However, if non-ideal effects associated with facility performance and energy release are included in the modeling (using CHEMSHOCK, a new model which couples the experimental pressure trace with the constant V, E assumptions), the predicted ignition times more closely follow the experimental data. Applying the new CHEMSHOCK model to current experimental data allows refinement of the reaction rate for H + O₂ + Ar ↔ HO₂ + Ar, a key reaction in determining the hydrogen-oxygen ignition delay time in the low-temperature region.     

Effects of NO2 addition on hydrogen ignition behind reflected shock waves

Ignition delay time measurements of H₂/O₂/NO₂ mixtures diluted in Ar have been measured in a shock tube behind reflected shock waves. Three different NO₂ concentrations have been studied (100, 400 and 1600 ppm) at three pressure conditions (around 1.5, 13, and 30 atm) and for various H₂–O₂ equivalence ratios for the 100 ppm NO₂ case. Results were compared to some recent ignition delay time measurements of H₂/O₂ mixtures. A strong dependence of the ignition delay time on the pressure and the NO₂ concentration was observed, whereas the variation in the equivalence ratio did not exhibit any appreciable effect on the delay time. A mechanism combining recent H₂/O₂ chemistry and a recent high-pressure NOx sub-mechanism with an updated reaction rate for H₂ + NO₂ ? HONO + H was found to represent correctly the experimental trends over the entire range of conditions. A chemical analysis was conducted using this mechanism to interpret the experimental results. Ignition delay time data with NO₂ and other NOx species as additives or impurities are rare, and the present study provides such data over a relatively wide pressure range.     

利用OH自由基特征发射谱测量正庚烷的点火延迟时间

在化学激波管中利用反射激波进行点火,采用OH自由基在306.4nm处特征发射谱线强度的急剧变化标志燃料的着火,由光谱单色仪、光电倍增管、压力传感器和示波器组成测量系统,测量了正庚烷/氧气的点火延迟时间,点火压力(1.0±0.1)和(0.75±0.05)atm,点火温度1 170～1 730K,当量比1.0,得到了在此实验条件下正庚烷/氧气点火延迟时间随温度变化的关系式。研究结果表明正庚烷/氧气点火延迟时间随温度的增加呈指数减小,点火压力为0.75atm时,随着点火温度的增加,点火延迟时间的变化率要小于1.0atm条件时。实验结果为建立正庚烷燃烧反应动力学模型,验证正庚烷燃烧反应机理提供了实验依据。     

JP-10点火延时的激波管研究

在预加热激波管上测定了JP-10的点火延时时间．采用高精度真空仪直接测定注入激波管中JP-10蒸气压力，获得了JP-10气相浓度，解决了高碳数碳氢燃料点火延时激波管实验时管壁吸附影响燃料气相浓度确定的困难．采用压力传感器、单色仪和光电倍增管记录得到了完整的点火过程引起的压力变化和OH或CH自由基发射强度变化．自由基发射信号作为诊断点火发生的手段．当实验压力为151?556 kPa，温度为1000?2120 K，JP-10摩尔百分比为0.1%?0.55%，化学当量比为0.25、0.5、1.0、2.0时，获得了点火延时时间与实验温度、JP-10浓度、O2浓度的依赖关系，结果还表明，高温区和低温区呈现出不同的依赖关系．     

Ignition delay times of methane and hydrogen highly diluted in carbon dioxide at high pressures up to 300 atm

The need for more efficient power cycles has attracted interest in super-critical CO₂ (sCO₂) cycles. However, the effects of high CO₂ dilution on auto-ignition at extremely high pressures has not been studied in depth. As part of the effort to understand oxy-fuel combustion with massive CO₂ dilution, we have measured shock tube ignition delay times (IDT) for methane/O₂/CO₂ mixtures and hydrogen/O₂/CO₂ mixtures using sidewall pressure and OH* emission near 306?nm. Ignition delay time was measured in two different facilities behind reflected shock waves over a range of temperatures, 1045–1578?K, in different pressures and mixture regimes, i.e., CH₄/O₂/CO₂ mixtures at 27–286 atm and H₂/O₂/CO₂ mixtures at 37–311 atm. The measured data were compared with the predictions of two recent kinetics models. Fair agreement was found between model and experiment over most of the operating conditions studied. For those conditions where kinetic models fail, the current ignition delay time measurements provide useful target data for development and validation of the mechanisms.     

入射激波诱导环氧丙烷爆炸特征研究

用自行设计激波管点火测试技术,实验研究了温度范围760-1380K间入射激波诱导下环氧丙烷的点火机理。利用激波管压力传感器测定了H*(486.1) 和O (470.5nm)随激波诱导强度变化的点火时间特征。实验结果表明：在低马赫数下氢氧自由基出现时间较接近,1.5-2.5马赫间随激波诱导强度增大而线性减小;而马赫大于2.5后,氧自由基的出现时间迅速减小,是由于高活化能的氧自由基的点火时间对强激波较敏感,而诱导强度大于3.5马赫后对两者点火影响区别就下明显了。实验数据将有益于含能材料点火时间的研究。     

入射激波诱导环氧丙烷爆炸特征研究

用自行设计激波管点火测试技术,实验研究了温度范围760-1380K间入射激波诱导下环氧丙烷的点火机理。利用激波管压力传感器测定了H*(486.1) 和O (470.5nm)随激波诱导强度变化的点火时间特征。实验结果表明：在低马赫数下氢氧自由基出现时间较接近,1.5-2.5马赫间随激波诱导强度增大而线性减小;而马赫大于2.5后,氧自由基的出现时间迅速减小,是由于高活化能的氧自由基的点火时间对强激波较敏感,而诱导强度大于3.5马赫后对两者点火影响区别就下明显了。实验数据将有益于含能材料点火时间的研究。     

A kinetics and dynamics study on the auto-ignition of dimethyl ether at low temperatures and low pressures

Though the combustion chemistry of dimethyl ether (DME) has been widely investigated over the past decades, there remains a dearth of ignition data that examines the low-temperature, low-pressure chemistry of DME. In this study, DME/‘air’ mixtures at various equivalence ratios from lean (0.5) to extremely rich (5.0) were ignited behind reflected shock waves at a fixed pressure (3.0 atm) over the temperature range 625–1200 K. The ignition behavior is different from that at high-pressures, with a repeatable ignition delay time fall-off feature observed experimentally in the temperature transition zone from the negative temperature coefficient (NTC) regime to the high-temperature regime. This could not be reproduced using available kinetic mechanisms as conventionally homogeneous ignition simulations. The fall-off behavior shows strong equivalence ratio dependence and disappears completely at an equivalence ratio of 5.0. A local ignition kernel postulate was implemented numerically to quantifiably examine the inhomogeneous premature ignition. At low temperature, no pre-ignition occurs in the mixture. A conspicuous discrepancy was observed between the measurements and constrained UV simulations at temperatures beyond the NTC regime. A third O₂ addition reaction sub-set was incorporated into AramcoMech 3.0, together with related species thermochemistry calculated using the G3/G4/CBS-APNO compound method, to explore the low-temperature deviation. The new reaction class does not influence the model predictions in IDTs, but the updated thermochemistry does. Sensitivity analyses indicate that the decomposition of hydroperoxy-methylformate plays a critical role in improving the low-temperature oxidation mechanism of DME but unfortunately, the thermal rate coefficient has never been previously investigated. Further experimental and theoretical endeavors are required to attain holistic quantitative chemical kinetics based on our understanding of the low-temperature chemistry of DME.     

Ignition limit and shock-to-detonation transition mode of n-heptane/air mixture in high-speed wedge flows

In this work, oblique detonation of n-heptane/air mixture in high-speed wedge flows is simulated by solving the reactive Euler equations with a two-dimensional (2D) configuration. This is a first attempt to model complicated hydrocarbon fuel oblique detonation waves (ODWs) with a detailed chemistry (44 species and 112 reactions). Effects of freestream equivalence ratios and velocities are considered, and the abrupt and smooth transition from oblique shock to detonation are predicted. Ignition limit, ODW characteristics, and predictability of the transition mode are discussed. Firstly, homogeneous constant-volume ignition calculations are performed for both fuel-lean and stoichiometric mixtures. The results show that the ignition delay generally increases with the wedge angle. However, a negative wedge angle dependence is observed, due to the negative temperature coefficient effects. The wedge angle range for successful ignition of n-heptane/air mixtures decreases when the wedge length is reduced. From two-dimensional simulations of stationary ODWs, the initiation length generally decreases with the freestream equivalence ratio, but the transition length exhibits weakly non-monotonic dependence. Smooth ODW typically occurs for lean conditions (equivalence ratio < 0.4). The interactions between shock/compression waves and chemical reaction inside the induction zone are also studied with the chemical explosive mode analysis. Moreover, the predictability of the shock-to-detonation transition mode is explored through quantifying the relation between ignition delay and chemical excitation time. It is demonstrated that the ignition delay (the elapsed time of the heat release rate, HRR, reaches the maximum) increases, but the excitation time (the time duration from the instant of 5% maximum HRR to that of the maximum) decreases with the freestream equivalence ratio for the three studied oncoming flow velocities. Smaller excitation time corresponds to stronger pressure waves from the ignition location behind the oblique shock. When the ratio of excitation time to ignition delay is high (e.g., > 0.5 for n-C₇H₁₆, > 0.3 for C₂H₂ and > 0.2 for H₂, based on the existing data compilation in this work), smooth transition is more likely to occur.     

An experimental and modeling study of the shock tube ignition of a mixture of n-heptane and n-propylbenzene as a surrogate for a large alkyl benzene

Alkyl aromatics are an important chemical class in gasoline, jet and diesel fuels. In the present work, an n-propylbenzene and n-heptane mixture is studied as a possible surrogate for large alkyl benzenes contained in diesel fuels. To evaluate it as a surrogate, ignition delay times have been measured in a heated high pressure shock tube (HPST) for a mixture of 57% n-propylbenzene/43% n-heptane in air (≈21% O₂, ≈79% N₂) at equivalence ratios of 0.29, 0.49, 0.98 and 1.95 and compressed pressures of 1, 10 and 30 atm over a temperature range of 1000–1600 K. The effects of reflected-shock pressure and equivalence ratio on ignition delay time were determined and common trends highlighted. A combined n-propylbenzene and n-heptane reaction mechanism was assembled and simulations of the shock tube experiments were carried out. The simulation results showed very good agreement with the experimental data for ignition delay times. Sensitivity and reaction pathway analyses have been performed to reveal the important reactions responsible for fuel oxidation under the shock tube conditions studied. It was found that at 1000 K, the main consumption pathways for n-propylbenzene are abstraction reactions on the alkyl chain, with particular selectivity to the allylic site. In comparison at 1500 K, the unimolecular decomposition of the fuel is the main consumption pathway.     

Experiments and modeling of ignition delay times, flame structure and intermediate species of EHN-doped stoichiometric n-heptane/air combustion

The combustion of stoichiometric Ethyl-hexyl-nitrate (EHN)-doped n-heptane/oxygen/argon and (EHN)-doped n-heptane/air mixtures, respectively, was investigated in a low-pressure burner with a molecular-beam mass spectrometer and ignition delay-time (τ_ign) measurements were performed in a high-pressure shock tube. The experiments with the low-pressure flame were used for the determination of the flame structure including concentration profiles of reactants, products and important intermediates in the flame. The shock tube experiments provided τ_ign for a temperature range of 690 K ? T ? 1275 K at a pressure of 40 ± 2 bar for stoichiometric and lean mixtures under engine relevant conditions. A chemical mechanism for n-heptane/EHN mixtures was developed from an automatically generated mechanism for n-heptane by manually adding reactions to describe the influence of EHN. This mechanism was validated against the shock-tube data for various temperatures, levels of EHN-doping and equivalence ratios by homogeneous reactor calculations.The ignition delay times predicted by the model agree well with the shock tube results for a large range of temperatures, equivalence ratios and EHN concentrations. The influence of EHN onto ignition delay was largest in the low-temperature regime (770-1000 K).Numerical analysis suggests that the prevalent reason for the ignition-enhancing effect of EHN is the formation of highly reactive heptyl radicals by thermal decomposition of EHN. Due to this comparatively simple and generic mechanism, EHN is expected to have a similar ignition-enhancing effect also for other hydrocarbon fuels.     

Autoignition of propane–air mixtures behind reflected shock waves

Ignition times and autoignition modes for propane–air mixtures have been studied behind reflected shock waves. Experiments were performed over temperatures between 1000 and 1750 K, pressures between 2 and 20 atm, and equivalence ratios of = 0.5, 1.0, and 2.0. Ignition delay times were determined using pressure measurements, C₂ emission profiles, and luminosity measurements in the visible spectrum (380–680 nm). Empirical correlations for ignition time for low temperature (1000–1300 K) and high temperature (1300–1800 K) ranges have been deduced from the experimental data. Different autoignition modes of the mixture (strong, transient, and weak) were identified by comparing velocities of reflected shock wave at different distances from the reflecting wall.     

Autoignition of gasoline surrogate mixtures at intermediate temperatures and high pressures: Experimental and numerical approaches

Ignition-delay times were measured in shock-heated gases for a surrogate gasoline fuel comprised of ethanol/iso-octane/n-heptane/toluene at a composition of 40%/37.8%/10.2%/12% by liquid volume with a calculated octane number of 98.8. The experiments were carried out in stoichiometric mixtures in air behind reflected shock waves in a heated high-pressure shock tube. Initial reflected shock conditions were as follows: Temperatures of 690-1200 K, and pressures of 10, 30 and 50 bar, respectively. Ignition delay times were determined from CH^∗ chemiluminescence at 431.5 nm measured at a sidewall location. The experimental results are compared to simulated ignition delay times based on detailed chemical kinetic mechanisms. The main mechanism is based on the primary reference fuels (PRF) model, and sub-mechanisms were incorporated to account for the effect of ethanol and/or toluene. The simulations are also compared to experimental ignition-delay data from the literature for ethanol/iso-octane/n-heptane (20%/62%/18% by liquid volume) and iso-octane/n-heptane/toluene (69%/17%/14% by liquid volume) surrogate fuels. The relative behavior of the ignition delay times of the different surrogates was well predicted, but the simulations overestimate the ignition delay, mostly at low temperatures.     

Ignition behavior of pure and blended methyl octanoate,n-nonane,and methylcyclohexane

Excited-state species profiles and ignition delay times were obtained under dilute conditions (99% Ar) using a heated shock tube for methyl octanoate (C₉H₁₈O₂), n-nonane (n-C₉H₂₀), and methylcyclohexane (MCH) over a broad range of temperature and equivalence ratio (? = 0.5, 1.0, 2.0) at pressures near 1 and 10 atm. Measurements were then extended to include two ternary blends of the fuels using 5% and 20% (vol.) of the methyl ester under stoichiometric conditions. Using three independently validated chemical kinetics mechanisms, a model was compiled to assess the influence of methyl ester concentration on ignition delay times of the ternary blends. Under near-atmospheric pressure, ignition delay times were of the following order for the pure fuels: methyl octanoate < n-nonane < methylcyclohexane. Experimental results indicate that the ignition behavior of the higher-order methyl ester approaches that of the higher-order linear alkane with increased pressure regardless of equivalence ratio. Methyl octanoate also displayed significantly lower pressure dependence relative to the linear alkane and the cycloalkane species. Both of these results are supported by model calculations. Blending of methyl octanoate with n-nonane and methylcyclohexane impacted ignition delay time results more strongly at 1.5 atm, yet had only a small effect near 10 atm for temperatures above 1400 K. The study provides the first shock-tube data for a ternary blend of a linear alkane, a cycloalkane, and a methyl ester. Ignition delay time measurements for the C₉:0 methyl ester were also measured for the first time.     

Ethanol ignition in a high-pressure shock tube: Ignition delay time and high-repetition-rate imaging measurements

Ethanol is known to be prone to pre-ignition in internal combustion engines under high-load conditions and its ignition shows large deviations from ideal, spatially, and temporally-homogeneous ignition in shock tubes at moderate temperatures (800–950 K). In this context, the ignition of stoichiometric ethanol/O₂ mixtures with various levels of inert gas dilution was investigated in a high-pressure shock tube at ?20 bar between 800 and 1250 K. Ignition delay times were determined from spatially integral detection of chemiluminescence emission. Additionally, high-repetition-rate color imaging enabled the differentiation of the luminescence in time, space, and spectral range between various ignition modes. In the low-temperature range (800–860 K), different inhomogeneous ignition modes were identified. The addition of small amounts of helium into the undiluted fuel/air mixture was found to be efficient to mitigate pre-ignition, attributed to a variation in heat transfer and thus suppression of the build-up of local temperature inhomogeneities. The experiments in case of spatially homogeneous ignition show very good agreement with the predictions based on three detailed kinetics mechanisms (Zhang et al., CNF 190 (2018) 74, Frassoldati et al., CNF 159 (2012) 2295, and Zhou et al. CNF 197 (2018) 423), inhomogeneities, however, resulted in a shortening of the ignition delay times up to a factor of 2.6.     

Ignition delay of fatty acid methyl ester fuel droplets: Microgravity experiments and detailed numerical modeling

Recent optical engine studies have linked increases in NO_x emissions from fatty acid methyl ester combustion to differences in the premixed autoignition zone of the diesel fuel jet. In this study, ignition of single, isolated liquid droplets in quiescent, high temperature air was considered as a means of gaining insight into the transient, partially premixed ignition conditions that exist in the autoignition zone of a fatty acid methyl ester fuel jet. Normal gravity and microgravity (10⁻⁴ m/s²) droplet ignition delay experiments were conducted by use of a variety of neat methyl esters and commercial soy methyl ester. Droplet ignition experiments were chosen because spherically symmetric droplet combustion represents the simplest two-phase, time-dependent chemically reacting flow system permitting a numerical solution with complex physical submodels. To create spherically symmetric conditions for direct comparison with a detailed numerical model, experiments were conducted in microgravity by use of a 1.1 s drop tower. In the experiments, droplets were grown and deployed onto 14 μm silicon carbide fibers and injected into a tube furnace containing atmospheric pressure air at temperatures up to 1300 K. The ignition event was characterized by measurement of UV emission from hydroxyl radical (OH*) chemiluminescence. The experimental results were compared against predictions from a time-dependent, spherically symmetric droplet combustion simulation with detailed gas phase chemical kinetics, spectrally resolved radiative heat transfer and multi-component transport. By use of a skeletal chemical kinetic mechanism (125 species, 713 reactions), the computed ignition delay period for methyl decanoate (C₁₁H₂₂O₂) showed excellent agreement with experimental results at furnace temperatures greater than 1200 K.