Oxygen diffusion and surface exchange studies on (La0.75Sr0.25)0.95Cr0.5Mn0.5O3−δ

Oxygen tracer diffusion coefficient (D^⁎) and surface exchange coefficient (k^⁎) have been measured for (La_0.75Sr_0.25)_0.95Cr_0.5Mn_0.5O_3−δ using isotopic exchange and depth profiling by secondary ion mass spectrometry technique as a function of temperature (700–1000 °C) in dry oxygen and in a water vapour-forming gas mixture. The typical values of D^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 4 × 10^− 10 cm² s^− 1 and 3 × 10^− 8 cm² s^− 1 respectively, whereas the values of k^⁎ under oxidising and reducing conditions at ∼ 1000 °C are 5 × 10^− 8 cm s^− 1 and 4 × 10^− 8 cm s^− 1 respectively. The apparent activation energies for D^⁎ in oxidising and reducing conditions are 0.8 eV and 1.9 eV respectively.     

A Boubaker polynomials expansion scheme (BPES)-related protocol for measuring sprayed thin films thermal characteristics

Measurements of In₂S₃ and ZnIn₂S₄ sprayed thin films thermal characteristics have been carried out using the photodetection technique. The thermal conductivity k and diffusivity D were obtained using a new protocol based on photothermal signal parameters analysis. Measured values of k and D were respectively, (15.2 ± 0.85) W m⁻¹K⁻¹ and (69.8 ± 7.1) × 10⁻⁶ m²s⁻¹ for In₂S₃, (7.2 ± 0.7) W m⁻¹K⁻¹ and (32.7 ± 4.3) × 10⁻⁶ m²s⁻¹ for ZnIn₂S₄. These values are extremely important since similar compounds are more and more proposed as Cd-free alternative materials for solar cells buffer layers.     

Synthesis of ammonia at atmospheric pressure with Ce0.8M0.2O2−δ (M = La,Y, Gd,Sm) and their proton conduction at intermediate temperature

Ionic conduction in fluorite-type structure oxide ceramics Ce_0.8M_0.2O_2−δ (M = La, Y, Gd, Sm) at temperature 400–800 °C was systematically studied under wet hydrogen/dry nitrogen atmosphere. On the sintered complex oxides as solid electrolyte, ammonia was synthesized from nitrogen and hydrogen at atmospheric pressure in the solid states proton conducting cell reactor by electrochemical methods, which directly evidenced the protonic conduction in those oxides at intermediate temperature. The rate of evolution of ammonia in Ce_0.8M_0.2O_2−δ (M = La, Y, Gd, Sm) is up to 7.2 × 10^− 9, 7.5 × 10^− 9, 7.7 × 10^− 9, 8.2 × 10^− 9 mol s^− 1 cm^− 2, respectively.     

Phase stability and oxygen non-stoichiometry of SrCo0.8Fe0.2O3−δ measured by in situ neutron diffraction

The phase stability, oxygen stoichiometry and expansion properties of SrCo_0.8Fe_0.2O_3−δ (SCF) were determined by in situ neutron diffraction between 873 and 1173 K and oxygen partial pressures of 5 × 10^− 4 to 1 atm. At a pO₂ of 1 atm, SCF adopts a cubic perovskite structure, space group Pm3¯m, across the whole temperature range investigated. At a pO₂ of 10^− 1 atm, a two-phase region exists below 922 K, where the cubic perovskite phase coexists with a vacancy ordered brownmillerite phase, Sr₂Co_1.6Fe_0.4O₅, space group Icmm. A pure brownmillerite phase is present at pO₂ of 10^− 2 and 5 × 10^− 4 atm below 1020 K. Above 1020 K, the brownmillerite phase transforms to cubic perovskite through a two-phase region with no brownmillerite structure observed above 1064 K. Large distortion of the BO₆ (B = Co, Fe) octahedra is present in the brownmillerite structure with apical bond lengths of 2.2974(4) Å and equatorial bond lengths of 1.9737(3) Å at 1021 K and a pO₂ of 10^− 2 atm. SCF is highly oxygen deficient with a maximum oxygen stoichiometry, 3 − δ, measured in this study of 2.58(2) at 873 K and a pO₂ of 1 atm and a minimum of 2.33(2) at 1173 K and a pO₂ of 5 × 10^− 4 atm. Significant differences in lattice volume and expansion behavior between the brownmillerite and cubic perovskite phases suggest potential difficulties in thermal cycling of SrCo_0.8Fe_0.2O_3−δ membranes.     

Effect of series resistance on the performance of silicon Schottky diode in the presence of tin oxide layer

The current–voltage (I–V) characteristics of Al/SnO₂/p-Si (MIS) Schottky diodes prepared by means of spray deposition method have been measured at 80, 295 and 350 K. In order to interpret the experimentally observed non-ideal Al/SnO₂/p-Si Schottky diode parameters such as, the series resistance R_s, barrier height Φ_B and ideality factor n, a novel calculation method has been reported by taking into account the applied voltage drop across interfacial oxide layer V_i and ideality factor n in the current transport mechanism. The values obtained for V_i were subtracted from the applied voltage values V and then the values of R_s were recalculated. The parameters obtained by accounting for the voltage drop V_i have been compared with those obtained without considering the above voltage drop. It is shown that the values of R_s estimated from Cheung’s method were strongly temperature-dependent and decreased with increasing temperature. It is shown that the voltage drop across the interfacial layer will increase the ideality factor and the voltage dependence of the I–V characteristics. The interface state density N_ss of the diodes has an exponential growth with bias towards the top of the valance band for each temperature; for example, from 2.37 × 10¹³ eV⁻¹ cm⁻² in 0.70−E_v eV to 7.47 × 10¹³ eV⁻¹ cm⁻² in 0.62−E_v eV for 295 K. The mean N_ss estimated from the I–V measurements decreased with increasing the temperature from 8.29 × 10¹³ to 2.20 × 10¹³ eV⁻¹ cm⁻².     

Studies on the effect of chlorides of magnesium,calcium, strontium and barium on the temperature of the sound velocity maximum of water

The effect of chlorides of magnesium, calcium, strontium and barium on the temperature of the sound velocity maximum (TSVM) of water, T_w, has been studied by determining the ultrasonic velocity using a single crystal variable path interferometer working at 3 MHz. The accuracy in ultrasonic velocity measurement is ± 0.05 m s^− 1. The ultrasonic velocity measurements were carried out at ≃ 2 °C intervals over a range of 5 °C to either side of TSVM of the solutions. The accuracy in fixing TSVM is ± 0.2 °C. The shifts in TSVM of water due to the addition of MgCl₂ and CaCl₂, (ΔT_obs), are found to be positive at low concentrations becoming maxima around the weight fraction w ≃ 2.3 × 10^− 2 for MgCl₂ and w ≃ 3.8 × 10^− 2 for CaCl₂ and becoming negative around w ≃ 5.6 × 10^− 2 for MgCl₂ and w ≃ 3.8 × 10^− 2 for CaCl₂. (ΔT_obs) for MgCl₂ > CaCl₂ > SrCl₂ > BaCl₂ indicating that the strength of the structural interactions in modifying the hydrogen-bonded structure of water is in the order Mg²⁺ > Ca²⁺ > Sr²⁺ > Ba²⁺. The results are explained in the light of the structural properties of the anions and cations in the solutions in modifying the three dimensional hydrogen-bonded structure of water.     

High room-temperature pyroelectric response of MgO-modified Pb0.99(Zr0.95Ti0.05)0.98Nb0.02O3 ceramics

The dielectric and pyroelectric responses of MgO-modified Pb_0.99(Zr_0.95Ti_0.05)_0.98Nb_0.02O₃ ceramics were investigated near F_R(LT)–F_R(HT) phase transition. It was found that MgO additive reduced the F_R(LT)–F_R(HT) phase transition temperature from 41 °C to room temperature (24 °C). Superior room-temperature pyroelectric properties were obtained in the composition of 0.10 wt% MgO addition without DC bias. The largest pyroelectric coefficient, 65 × 10⁻⁸ C cm⁻² K⁻¹, was detected. Accordingly, the detectivity figures of merit F_d had maximum values of 20 × 10⁻⁵ Pa^−1/2, and especially the voltage responsivity F_v = 0.91 m²C⁻¹ is the highest value reported so far among all pyroelectric materials. It shows promising potential for application in uncooled pyroelectric infrared detector.     

Interfacial energies of carbon tetrabromide

The equilibrated grain boundary groove shapes for solid carbon tetrabromide (CTB) in equilibrium with its melt were directly observed by using a horizontal temperature gradient stage. From the observed grain boundary groove shapes, Gibbs–Thomson coefficient (Γ) and solid–liquid interfacial energy (σ_SL) and grain boundary energy (σ_gb) of CTB have been determined to be (7.88 ± 0.8) × 10⁻⁸ K m, (6.91 ± 1.04) × 10⁻³ J m⁻² and (13.43 ± 2.28) × 10⁻³ J m⁻², respectively. The ratio of thermal conductivity of equilibrated liquid phase to solid phase for CTB has also been measured to be 0.90 at its melting temperature. The value of σ_SL for CTB obtained in present work was compared with the values of σ_SL determined in the previous works for same material and it was seen that the present result is in good agreement with previous works.     

3 MeV electron irradiation-induced defects in CuInSe2 thin films

3 MeV electron irradiation induced-defects in CuInSe₂ (CIS) thin films have been investigated. Both of the carrier concentration and Hall mobility were decreased as the electron fluence exceeded 1×10¹⁷ cm⁻². The carrier removal rate was estimated to be about 1 cm⁻¹. To evaluate electron irradiation-induced defect, the electrical properties of CIS thin films before and after irradiation were investigated between 80 and 300 K. From the temperature dependence of the carrier concentration in non-irradiated thin films, we obtained N_D=1.8×10¹⁷ cm⁻³, N_A=1.7×10¹⁶ cm⁻³ and E_D=18 meV from the SALS fitting to the experimental data on the basis of the charge balance equation. After irradiation, a new defect level was formed, and N_T0=1.4×10¹⁷ cm⁻³ and E_T=54 meV were also obtained from the same procedure. From the temperature dependence of Hall mobility, the ionized impurity density was discussed before and after the irradiation.     

Investigating gate metal induced reduction of surface donor density in GaN/AlGaN/GaN heterostructure by electroreflectance spectroscopy

The internal field of GaN/AlGaN/GaN heterostructure on Si-substrate was investigated by varying the thickness of an undoped-GaN capping layer using electroreflectance spectroscopy. The four samples investigated are AlGaN/GaN heterostructure without a GaN cap layer (reference sample) and three other samples with GaN/AlGaN/GaN heterostructures in which the different thickness of GaN cap layer (2.7 nm, 7.5 nm, and 12.4 nm) has been considered. The sheet carrier density (n_s) of a two-dimensional electron gas has decreased significantly from 4.66 × 10¹² cm⁻² to 2.15 × 10¹² cm⁻² upon deposition of a GaN capping layer (12.4 nm) over the reference structure. Through the analysis of internal fields in each GaN capping and AlGaN barrier layers, it has been concluded that the undiminished surface donor states (n_s) of a reference structure and the reduced n_s caused by the Au gate metal are approximately 5.66 × 10¹² cm⁻² and 1.08 × 10¹² cm⁻², respectively.     

Lipase catalyzed ultrasonic synthesis of poly-4-hydroxybutyrate-co-6-hydroxyhexanoate

Four different lipases were compared for ultrasound-mediated synthesis of the biodegradable copolymer poly-4-hydroxybutyrate-co-6-hydroxyhexanoate. The copolymerization was carried out in chloroform. Of the enzymes tested, Novozym 435 exhibited the highest copolymerization rate, in fact the reaction rate was observed to increase with about 26-fold from 30 to 50 °C (7.9 × 10^?3 M s^?1), sonic power intensity of 2.6 × 10³ W m^?2 and dissipated energy of 130.4 J ml^?1. Copolymerization rates with the Candida antarctica lipase A, Candida rugosa lipase, and Lecitase Ultra? were lower at 2.4 × 10^?4, 1.3 × 10^?4 and 3.5 × 10^?4 M s^?1, respectively. The catalytic efficiency depended on the enzyme. The efficiency ranged from 4.15 × 10^?3 s^?1 M^?1 for Novozym 435–1.48 × 10^?3 s^?1 M^?1 for C. rugosa lipase. Depending on the enzyme and sonication intensity, the monomer conversion ranged from 8.2% to 48.5%. The sonication power, time and temperature were found to affect the rate of copolymerization. Increasing sonication power intensity from 1.9 × 10³ to 4.5 × 10³ W m^?2 resulted in an increased in acoustic pressure (P_a) from 3.7 × 10⁸ to 5.7 × 10⁸ N m^?2 almost 2.4–3.7 times greater than the acoustic pressure (1.5 × 10⁸ N m^?2) that is required to cause cavitation in water. A corresponding acoustic particle acceleration (a) of 9.6 × 10³–1.5 × 10⁴ m s^?2 was calculated i.e. approximately 984–1500 times greater than under the action of gravity.     

Synthesis of TiO2/WO3 nanoparticles via sonochemical approach for the photocatalytic degradation of methylene blue under visible light illumination

Through an ultrasound assisted method, TiO₂/WO₃ nanoparticles were synthesized at room temperature. The XRD pattern of as-prepared TiO₂/WO₃ nanoparticles matches well with that of pure monoclinic WO₃ and rutile TiO₂ nanoparticles. TEM images show that the prepared TiO₂/WO₃ nanoparticles consist of mixed square and hexagonal shape particles about 8–12 nm in diameter. The photocatalytic activity of TiO₂/WO₃ nanoparticles was tested for the degradation of a wastewater containing methylene blue (MB) under visible light illumination. The TiO₂/WO₃ nanoparticles exhibits a higher degradation rate constant (6.72 × 10⁻⁴ s⁻¹) than bare TiO₂ nanoparticles (1.72 × 10⁻⁴ s⁻¹) under similar experimental conditions.     

Transport and phase dynamics of poly(vinyl pyrrolidone) doped plastically crystalline N-methyl-N-propylpyrrolidinium tetrafluoroborate

The plastic crystal phase forming N-methyl-N-propylpyrrolidinium tetrafluoroborate organic salt (P₁₃BF₄) was combined with 2, 5 and 10 wt.% poly(vinyl pyrrolidone) (PVP). The ternary 2 wt.% PVP/2 wt.% LiBF₄/P₁₃BF₄ was also investigated. Thermal analysis, conductivity, optical thermomicroscopy, and Nuclear Magnetic Resonance (¹¹B, ¹⁹F, ¹H, ⁷Li) were used to probe the fundamental transport processes. Both the onset of phase I and the final melting temperature were reduced with increasing additions of PVP. Conductivity in phase I was 2.6 × 10^− 4 S cm^− 1 5.2 × 10^− 4 S cm^− 1 1.1 × 10^− 4 S cm^− 1 and 3.9 × 10^− 5 S cm^− 1 for 0, 2, 5 and 10 wt.%PVP/P₁₃BF₄, respectively. Doping with 2 wt.% LiBF₄ increased the conductivity by up to an order of magnitude in phase II. Further additions of 2 wt.% PVP slightly reduced the conductivity, although it remained higher than for pure P₁₃BF₄.     

Study on the kinetics properties of lithium hexafluorophosphate thermal decomposition reaction

The thermal decomposition of lithium hexafluorophosphate was studied by using C80 calorimeter, and the samples were heated at a 0.2 K·min^− 1 heating rate from ambient temperature to 573 K in pressure-sensitive transducer fitted and sealed vessel with argon atmosphere. It is found that LiPF₆ decomposes near 433 K, and the gas product PF₅ causes the pressure increasing. The LiPF₆ decomposition reaction order is calculated based on the pressure data by two methods, its average value is n = 1.5, then, the reaction is assumed to be dependent on the Arrhenius law and mass action law, and thus the activation energy and pre-exponential factor were calculated to be E = 104.2 kJ·mol^− 1, A = 1.12 × 10⁷ s^− 1, respectively.     

Structural,XPS and impedance analysis of LixCoVO4 (x = 0.8, 1.0, 1.2)

Lithium cobalt vanadate Li_xCoVO₄ (x = 0.8; 1.0; 1.2) has been prepared by a solid state reaction method. The XRD analysis confirms the formation of the sample. A new peak has been observed for Li_1.0CoVO₄ and for Li_1.2CoVO₄ indicating the formation of a new phase. The XPS analysis indicates the reduction in the oxidation of vanadium and oxygen with the addition of Li in Li_xCoVO₄ (x = 0.8, 1.0, 1.2). The impedance analysis gives the conductivity value as 2.46 × 10^− 5, 6.16 × 10^− 5, 9 × 10^− 5 Ω^− 1 cm^− 1 for Li_xCoVO₄ (x = 0.8; 1.0; 1.2), all at 623 K. The similarity in the bulk activation energy (E_a) and the activation enthalpy for migration of ions (E_ω) indicate that the conduction in Li_1.2CoVO₄ has been due to hopping mechanism.     

Quick response PZT/P(VDF-TrFE) composite film pyroelectric infrared sensor with patterned polyimide thermal isolation layer

The fabrication method and the pyroelectric response of a single element infrared sensor based lead zirconate titanate (PZT) particles and polyvinylidene fluoride P(VDF-TrFE) copolymer composite thick film is reported in this paper. A special thermal insulation structure, including polyimide (PI) thermal insulation layer and thermal insulation tanks, was used in this device. The thermal insulation tanks were fabricated by laser micro-etching technique. Voltage responsivity (R_V), noise voltage (V_noise), noise equivalent power (NEP), and detectivity (D^*) of the PZT/P(VDF-TrFE) based infrared sensor are 1.2 × 10³ V/W, 1.25 × 10⁻⁶ V Hz^1/2, 1.1 × 10⁻⁹ W and 1.9 × 10⁸ cm Hz^1/2 W⁻¹ at 137.3 Hz modulation frequency, respectively. The thermal time constant of the infrared sensor τ_T was about 15 ms. The results demonstrate that the composite infrared sensor show a high detectivity at high chopper frequency, which is an essential advantage in infrared detectors and some other devices.     

Thermal and chemical expansion of mixed conducting La0.5Sr0.5Fe1−xCoxO3−δ materials

Oxygen deficiency, thermal and chemical expansion of La_0.5Sr_0.5Fe_1−xCo_xO_3−δ (x = 0, 0.5, 1) have been measured by thermogravimetry, dilatometry and high temperature X-ray diffraction. The rhombohedral perovskite materials transformed to a cubic structure at 350 ± 50 °C. The thermal expansion of the materials up to the onset of thermal reduction was 14–18 × 10^− 6 K^− 1. Above 500 °C in air (400 °C in N₂), chemical expansion contributed to the thermal expansion and the linear thermal expansion coefficients were significantly higher, 16–35 × 10^− 6 K^− 1. The chemical expansion, ε_c, showed a maximum of 0.0045 for x = 0.5 and 0.0041 for x = 1 at 800–900 °C. The normalized chemical expansion, ε_c/Δδ, was 0.036 for x = 0.5 and 0.035 for x = 1 at 800 °C. The chemical expansion can be correlated with an increasing ionic radius of the transition metals with decreasing valence state.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

Shock tube/laser absorption studies of the decomposition of methyl formate

Reaction rate coefficients for the major high-temperature methyl formate (MF, CH₃OCHO) decomposition pathways, MF → CH₃OH + CO (1), MF → CH₂O + CH₂O (2), and MF → CH₄ + CO₂ (3), were directly measured in a shock tube using laser absorption of CO (4.6 μm), CH₂O (306 nm) and CH₄ (3.4 μm). Experimental conditions ranged from 1202 to 1607 K and 1.36 to 1.72 atm, with mixtures varying in initial fuel concentration from 0.1% to 3% MF diluted in argon. The decomposition rate coefficients were determined by monitoring the formation rate of each target species immediately behind the reflected shock waves and modeling the species time-histories with a detailed kinetic mechanism [12]. The three measured rate coefficients can be well-described using two-parameter Arrhenius expressions over the temperature range in the present study: k₁ = 1.1 × 10¹³ exp(?29556/T, K) s^?1, k₂ = 2.6 × 10¹² exp(?32052/T, K) s^?1, and k₃ = 4.4 × 10¹¹ exp(?29 078/T, K) s^?1, all thought to be near their high-pressure limits. Uncertainties in the k₁, k₂ and k₃ measurements were estimated to be ±25%, ±35%, and ±40%, respectively. We believe that these are the first direct high-temperature rate measurements for MF decomposition and all are in excellent agreement with the Dooley et al. [12] mechanism. In addition, by also monitoring methanol (CH₃OH) and MF concentration histories using a tunable CO₂ gas laser operating at 9.67 and 9.23 μm, respectively, all the major oxygen-carrying molecules were quantitatively detected in the reaction system. An oxygen balance analysis during MF decomposition shows that the multi-wavelength laser absorption strategy used in this study was able to track more than 97% of the initial oxygen atoms in the fuel.