TBPe与MEH-PPV共掺杂的有机电致发光器件的优化研究

采用有机小分子TBPe（2,5,8,11-tetratertbutylperylene）以不同比例掺入MEH-PPV（poly ）作为发光层,研究了TBPe不同掺杂比例对器件性能的影响,进而对发光强度进行优化。对于所制备的ITO/PEDOT：PSS/MEH-PPV/TBPe/Al有机电致发光器件,TBPe的最优蒸镀厚度为0.5 nm,其发光强度相对于标准器件提高了325%。ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Liq/Al有机电致发光器件的最优掺杂比例为MEH-PPV：TBPe=100：30（质量比）,其发光亮度相比于未掺杂器件提高了44%。在上述器件的基础上增加Alq₃层提高电子注入,分别制作了Liq和LiF作为修饰层的ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Alq₃/Liq/Al和ITO/PEDOT：PSS/MEH-PPV：TBPe/TBPe/Alq₃/LiF/Al多层器件,发光亮度分别达到4 162 cd/m²和4 701 cd/m²。所有器件的电致发光波长均为580 nm,为MEH-PPV的发光,TBPe的掺杂对MEH-PPV的发光起到了增强作用。     

体异质结有机太阳能电池性能提高的研究

制备了四种不同结构的有机太阳能电池器件,器件1 ITO/LiF/PEDOT∶PSS/MEH-PPV/C₆₀/Al、器件2 ITO/PEDOT∶PSS/MEH-PPV/C₆₀/Al、器件3 ITO/LiF/PEDOT∶PSS/MEH-PPV∶C₆₀/C₆₀/Al和器件4 ITO/PEDOT∶PSS/MEH-PPV∶C₆₀/C₆₀/Al。测量了它们的电流－电压特性,结果显示在ITO和PEDOT∶PSS之间插入一薄层LiF使得器件性能得到较大提高。其器件1的J_SC和FF比器件2的提高了74%和31%; 器件3的J_SC比器件4的提高了约40%。这主要是由于LiF层有效地抑制了空穴向阳极的传输,并且LiF层在ITO和PEDOT:PSS之间形成了良好的界面特性。因此,这种结构上的改进有效地提高了有机太阳能电池的性能。     

基于量子点和MEH-PPV的白光发光二极管的研究

利用无机纳米材料与有机聚合物材料相结合的方法制备白光发光二极管器件, 研究了蓝光量子点QDs(B)掺杂聚[2-甲氧基-5-(2-乙基己氧基-1, 4-苯撑乙烯撑](MEH-PPV) 复合体系的发光特性及量子点QDs(B) 掺杂浓度(质量分数)不同对器件发光特性的影响. 制备了ITO/PEDOT:PSS/MEH-PPV:QDs(B)/LiF/Al 结构的电致发光器件, 测试了器件的电致发光光谱和电学、光学特性. 当QDs掺杂浓度为40%, 驱动电压为8 V时器件能得到较为理想的白光发射. 同时, 对比研究了非掺杂体系的发光特性, 制备了结构为ITO/PEDOT:PSS/MEH-PPV/QDs(B)/LiF/Al的器件, 掺杂体系相较于非掺杂体系, 器件的最大亮度增大, 启亮电压降低, 并分析了掺杂体系器件性能改善的原因.     

ZnSe(ZnS)纳米晶与MEH-PPV的共掺有机电致发光器件

采用水相法合成核壳结构ZnSe/ZnS 纳米晶,经X射线衍射(XRD)分析和透射电子显微镜(TEM)表征,证实所制备的样品为立方晶型闪锌矿结构ZnSe/ZnS量子点。按照一定的质量比将ZnSe/ZnS 纳米晶和有机聚合物MEH-PPV(poly ) 共掺并将其作为发光层,分别制备单层和多层有机电致发光器件,结构为ITO/MEH-PPV∶ZnSe(ZnS)(50 nm)/Al和 ITO/PEDOT∶PSS(70 nm)/ MEH-PPV∶ZnSe(ZnS)(50 nm)/BCP(15 nm)/Alq₃(12 nm) /LiF(0.5 nm)/Al。实验结果表明,多层发光器件的发光特性与单层器件不同,工作电压的增大使其发光峰发生了明显的蓝移。     

不同电极对蓝光有机电致发光器件性能的影响

利用高真空多源型有机分子沉积系统分别制备了不同负电极为Al、LiF/Al和Mg:Ag的有机小分子多层电致发光器件,比较了不同负极对以五苯基环戊二烯（PPCP）为发光层的蓝光有机电致发光器件性能的影响,发现以LiF/Al作负极的器件在综合性能上优于其它器件。其中器件ITO／TPD／PPDP／Alq/LiF/Al蓝光发射的最大发光亮度达2375cd/m^2,最大发光效率为0.26lm/W.     

以联苯乙烯衍生物为发光层的蓝色有机发光二极管特性的研究

以一种新型联苯乙烯衍生物NPVBi作为发光层，制备了结构为：ITO／TPD／NPVBi/Alq3/LiF/Al的有机薄膜电致发光器件，其中TPD厚度保持为50nm,NPVBi与Alq3厚度之和保持为50nm。通过调节NPVBi与Alq3的厚度，获得了色纯度较好的NPVBi蓝色电致发光，最高亮度为708cd/m^2，最大流明效率为1.13lm/W。结果表明，发光层NPVBi和电子传输层Alq3的厚度对器件的发光特性有显著的影响。     

9,9-二辛基聚芴-苯并噻二唑交替共聚物的绿光偏振电致发光

通过缩聚法合成了绿光9,9-二辛基聚芴-苯并噻二唑交替共聚物（PFBT）.该聚合物在一定温度范围内形成向列液晶态,利用其在定向层上的有序排列,实现了峰值发光波长为550 nm的偏振电致发光.采用摩擦后的空穴注入层聚（3,4-乙撑二氧噻吩）∶聚（苯乙烯磺酸）（PEDOT:PSS）作为定向层,通过偏振紫外可见吸收光谱和偏振光致发光谱,研究了聚合物分子在薄膜平面内的单轴取向特性,计算得到薄膜的有序参数为075.制备了结构为ITO/PEDOT:PSS/PFBT/LiF/Al的聚合物电致发光器件,工作电压为15 V时,电致发光偏振率达到4,亮度和流明效率分别为450 cd/m²和021 cd/A. 关键词： 偏振发光 交替共聚物 聚合物电致发光器件     

PCDTBT作为发光层的有机电致发光器件研究

使用PCDTBT作为发光层材料,制备了发光波长为705 nm的红色有机电致发光器件,其结构为ITO/PEDOT:PSS/PCDTBT/BCP/LiF/Al.器件启亮电压为2 V,在9 V时器件达到最高亮度,为29000 cd/m2,最大电流效率为3.5 cd/A.还研究了不同退火温度对器件发光性能的影响.实验结果表明,退火温度为50?C时器件的性能最佳,其原因是此时既有利于溶剂挥发,又保持了分子结构的稳定性,而高温退火降低了PCDTBT的π-π堆积的有序性,从而使得器件性能下降.     

PVK∶DBVP掺杂体系的能量转移及发光性质的研究

研究了不同比例的PVK与齐聚PPV衍生物DBVP掺杂体系的能量转移和发光特性.通过对PVK,DBVP及PVK:DBVP掺杂体系的UV-vis,PL和PLE光谱的研究,分析了PVK与DBVP之间的能量转移过程.利用PVK在体系中类似于溶剂的分散作用,制备了结构为ITO/PEDOT/PVK:DBVP/LiF/Al的电致发光器件,研究了掺杂体系的电致发光性能.结果表明,在掺杂体系的光致发光和电致发光中,PVK的发射被有效地抑制,PVK与DBVP之间发生了非常有效的能量转移,通过调节PVK与DBVP的比例,可以获得蓝色和绿色发光,同时可以改善器件的发光性能,当PVK与DBVP的重量比为1∶2时,器件的绿色发光效率达到1·06cd/A,此时发光亮度为52cd/m2.     

PVK:DBVP掺杂体系的能量转移及发光性质的研究

研究了不同比例的PVK与齐聚PPV衍生物DBVP掺杂体系的能量转移和发光特性.通过对PVK，DBVP及PVK: DBVP掺杂体系的UV-vis，PL和PLE光谱的研究，分析了PVK与DBVP之间的能量转移过程.利用PVK在体系中类似于溶剂的分散作用，制备了结构为ITO/PEDOT/PVK: DBVP/LiF/Al的电致发光器件，研究了掺杂体系的电致发光性能.结果表明，在掺杂体系的光致发光和电致发光中，PVK的发射被有效地抑制，PVK与DBVP之间发生了非常有效的能量转移，通过调节PVK与DBVP的比例，可以获得蓝色和绿色发光，同时可以改善器件的发光性能，当PVK与DBVP的重量比为1∶2时，器件的绿色发光效率达到1.06cd/A，此时发光亮度为52cd/m².     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.