多铁材料Bi1-xCaxFeO3的介电、铁磁特性和高温磁相变

采用溶胶凝胶法制备Bi_1-xCa_xFeO₃ (x=0, 0.05, 0.1, 0.15, 0.2)陶瓷样品. X衍射图谱表明所有样品的主衍射峰均与纯相BiFeO₃相符合且具有良好的晶体结构. 随着x的增大, Bi_1-xCa_xFeO₃样品的主衍射峰由双峰(104)与(110) 逐渐重叠为单峰(110), 当x ≥0.15时, 样品呈现正方晶系结构; 扫描电镜形貌分析可知, 晶粒由原来的0.5 μm逐渐增大到2 μm. Bi_1-xCa_xFeO₃样品介电常数和介电损耗随着x 的增加先增大而后减小. 当f=1 kHz, Bi_0.9Ca_0.1FeO₃ 的介电常数达到最大值, 是BiFeO₃的7.5倍, 而Bi_0.8Ca_0.2FeO₃的介电常数达到最小值, 仅仅是BiFeO₃的十分之一. Bi_1-xCa_xFeO₃样品所呈现的介电特性是由偶极子取向极化和空间电荷限制电流两种极化机理共同作用的结果. 随着Ca²⁺ 的引入, BiFeO₃ 样品的铁磁性显著提高. X射线光电子能谱图表明Fe²⁺和Fe³⁺ 共存于Bi_1-xCa_xFeO₃ 样品中, Fe²⁺/Fe³⁺比例随着Ca²⁺ 掺杂量的增加而增大, 证明Ca²⁺掺杂增加了Fe²⁺的含量, 增强BiFeO₃的铁磁特性. 从M-T曲线观察到BiFeO₃样品在878 K附近发生铁磁相变, 示差扫描量热法测试再次证明BiFeO₃ 在878 K发生相变. Ca²⁺掺杂使BiFeO₃样品的T_N略有变化而T_M基本不变, 其主要原因是Fe-O-Fe反铁磁超交换作用的强弱和磁结构相对稳定.     

Bi0.5Ca0.5Mn1-xCoxO3体系中的电荷有序和相分离

利用固相反应法制备了Bi_0.5Ca_0.5Mn_1-xCo_xO₃(0≤x≤0.12)系列多晶样品.研究了Co掺杂对Bi_0.5Ca_0.5MnO₃电荷有序的影响.结果表明,Co掺杂导致电荷有序相逐渐融化、铁磁相互作用的增强;当x≥0.08时,电荷有序转变峰完全消失,但残留的反铁磁电荷有 关键词： 钙钛矿锰氧化物 电荷有序 团簇玻璃 相分离     

Co(S1-xSex)2系统中的铁磁量子相变

针对Co(S_1-xSe_x)₂系统在x=0.11附近发生的铁磁金属到顺磁金属相变,制备了一系列不同Se替代浓度的多晶样品.通过对其结构和电阻率-温度ρ(T)关系的系统观测,结果发现,样品铁磁相变温度T_C随着Se替代浓度x值的增加,以(1-x)^1/2关系单调下降,其二级铁磁相变转变为一级相变 关键词： 量子相变 自旋量子涨落 1-xSe_x)₂')" href="#">Co(S_1-xSe_x)₂     

Ti1－xCrxO2±δ体系的相关系、晶体结构和磁性能研究

采用溶胶凝胶法制备了Ti_1-xCr_xO_2±δ体系系列样品.利用扫描电子显微镜(SEM)，X射线光电子能谱(XPS)，粉末X射线衍射分析(XRD)方法研究了Ti_1-xCr_xO_2±δ系列样品的颗粒尺寸、形貌、组分化学态、相关系和固溶区范围；并利用超导量子干涉磁强计对样品的磁性能进行了研究.采用Rietveld结构精修的方法研究了Cr的不同掺杂量对TiO₂晶体结构的影响，研究表明，1000℃烧结的样品的固溶区范围是x=0—0.03，为金红石单相；随着Cr掺杂量的增加，金红石相晶胞参数规律性地减小；当x>0.03，为金红石相和CrO₂相两相共存.综合XRD和磁性测量结果，500℃烧结的样品的固溶区范围是x=0—0.02，为锐钛矿单相；随着Cr掺杂量的增加，锐钛矿相晶胞参数规律性地减小；当x≥0.04，为锐钛矿相和绿铬矿相(Cr₂O₃)两相共存.XPS实验结果表明，500℃和1000℃退火的样品中Cr都是以Cr⁺³和Cr⁺⁶两种化学态存在，1000℃烧结的样品中可能有更多的Cr³⁺转化为Cr⁶⁺.根据M-H和M-T曲线的测试结果发现，本文500℃烧结的Ti_1-xCr_xO_2±δ体系样品当x=0—0.02时，为室温铁磁性.当x≥0.04时，由铁磁相和顺磁相所组成，在低温下有较强的铁磁性；室温下主要是顺磁相，铁磁相只占据很小的体积分数. 关键词： 1-xCr_xO_2±δ体系')" href="#">Ti_1-xCr_xO_2±δ体系 相关系 固溶区 磁性能     

多自旋态离子Co替代诱导La2/3Ca1/3MnO3体系的输运反常

利用具有多自旋态的Co离子进行Mn位替代,制备了La_2/3Ca_1/3Mn_1-xCo_xO₃ (0≤x≤0.15) 系列样品并研究了体系的结构和输运特性.结果表明,在替代范围内,样品呈现很好的单相结构,各晶格参数随替代量的增大而减小;Co替代导致体系出现电输运反常,具体表现为在居里温度T_C以下电阻-温度曲线的二次金属-绝缘转 关键词： Mn位替代 双峰现象 自旋结构 磁电阻效应     

钙钛矿锰氧化物(La1-xGdx)4/3Sr5/3Mn2O7 (x=0, 0.025) 磁性和输运性质研究

采用传统的高温固相烧结法制备了双层钙钛矿锰氧化物(La_1-xGd_x)_4/3Sr_5/3Mn₂ O₇ (x=0, 0.025)多晶样品. 通过X射线衍射仪研究发现样品为Sr₃Ti₂O₇型四方结构, 空间群为I4/mmm; 磁性测量表明, Gd³⁺掺杂后的样品(La_0.975Gd_0.025)_4/3Sr_5/3Mn₂O₇的三维磁有序转变温度(T_C1^3D)、磁化强度(M)均降低, 这是由于Gd³⁺的掺杂引起晶格的畸变, 从而使得晶格常数发生改变, 减弱了铁磁耦合而导致的; 通过电子自旋共振谱测量发现, 在T_C^3D<T<300 K温度范围内, 两样品在顺磁的基体上均有短程的铁磁团簇存在, 出现了相分离现象. 电性测量表明: 两样品分别在T_C1^3D (La_4/3Sr_5/3Mn₂O₇ 样品的三维磁有序转变温度, T_C0^3D)<T<300 K温度范围内均以三维变程跳跃的方式导电, 分析得出Gd³⁺的掺杂使得载流子局域长度的减小. 这表明载流子需要吸收更多的能量才能克服晶格的束缚进行跳跃, 因此(La_0.975Gd_0.025)_4/3Sr_5/3Mn₂ O₇ 样品的电阻较高.     

尖晶石铁氧体TixNi1-xFe2O4中阳离子分布和Ti离子磁矩的实验研究

采用固相反应法制备了系列样品Ti_xNi_1-xFe₂O₄ (x=0.0, 0.1, 0.2, 0.3, 0.4). 室温下的X射线衍射谱表明样品全部为(A)[B]₂O₄型单相立方尖晶石结构, 属于空间群Fd3m. 样品的晶格常数随Ti掺杂量的增加而增大. 样品在10 K温度下的比饱和磁化强度σ_S随着Ti掺杂量x的增加逐渐减小. 研究发现, 当Ti掺杂量x≥ 0.2时, 磁化强度σ随温度T的变化曲线出现两个转变温度T_L和T_N. 当温度低于T_N时, 磁化强度明显减小; 当温度达到T_N时, dσ/dT具有最大值. σ-T曲线的这些特征表明, 由于Ti掺杂在样品中出现了附加的反铁磁结构. 这说明样品中的Ti离子不是无磁性的+4价离子, 而是以+2和+3价态存在, 其离子磁矩的方向与Fe和Ni离子的磁矩方向相反. 利用本课题组提出的量子力学方势垒模型拟合样品在10 K温度下的磁矩, 得到了Ti, Fe和Ni三种阳离子在(A)位和[B]位的分布情况, 并发现在所有掺杂样品中, 80%的Ti离子以+2价态占据尖晶石结构的[B]位.     

Sr掺杂钙钛矿型氧化物Y1-xSrxCoO3的溶胶-凝胶制备及电阻率温度关系研究

采用溶胶-凝胶方法成功制备了Sr的替代化合物Y_1-xSr_xCoO₃ (x=0, 0.01, 0.05, 0.10, 0.15, 0.20), 系统地研究了20–720 K温度范围内Y_1-xSr_xCoO₃的电阻率温度关系. 研究表明, 随着Sr的替代含量的增加, Y_1-xSr_xCoO₃的电阻率迅速地降低, 这主要是由于载流子浓度的增加引起. 样品x=0和0.01在低于330和260 K的温度范围内, 电阻率与温度之间满足指数关系lnρ∝1/T, 获得导电激活能分别为0.2950和0.1461 eV. 然而, 实验显示lnρ∝1/T关系仅成立于重掺杂样品的高温区; 在低温区莫特定律lnρ∝T^-1/4成立, 且表明重掺杂引入势垒, 导致大量局域态的形成. 根据莫特T^-1/4定律拟合实验数据, 评估了局域态密度N(E_F), 它随着掺杂量的增加而增加. 关键词： 热电材料 溶胶-凝胶 3')" href="#">YCoO₃     

Ni2O3掺杂对新固相源顶部籽晶熔渗生长法制备单畴GdBCO超导块材超导性能的影响

本文通过在新固相源中添加Ni₂O₃的方法, 采用顶部籽晶熔渗生长工艺(TSIG)制备出组分为(1-x) (Gd₂O₃+1.2BaCuO₂)+x Ni₂O₃、直径为20 mm的单畴GdBCO 超导块材(其中x = 0, 0.02, 0.06, 0.10, 0.14, 0.18, 0.30, 0.50 wt%), 并研究了Ni₂O₃的掺杂量x对样品的表面生长形貌、微观结构、临界温度T_c、磁悬浮力以及俘获磁通密度的影响. 研究结果表明, 当Ni₂O₃的掺杂量x在0–0.50 wt%的范围内时, 均可制备出单畴性良好的样品, 且Ni₂O₃的掺杂对样品中Gd211粒子的分布和粒径没有明显的影响. 在Ni₂O₃的掺杂量x从0增加到0.50 wt%的过程中, 样品的临界温度T_c呈现下降的趋势, 从x=0时的92.5 K下降到x=0.50 wt%时的86.5 K, 这是由于Ni^{3 +}替代GdBCO晶体中Cu^{2 +}所致; 样品磁悬浮力和俘获磁通密度均呈现先增大后减小的变化规律, x=0.14 wt%时, 磁悬浮力达到最大值34.2 N, x=0.10 wt%时, 俘获磁通密度达到最大值0.354 T. 样品磁悬浮力和俘获磁通密度的变化规律与Ni₂O₃的掺杂量x有密切关系, 只有当掺杂量x合适时, Ni³⁺对Cu^{2 +}的替代既不会造成T_c的明显下降, 但又能产生适量的Ni^{3 +}/Cu²⁺ 晶格畸变, 从而达到提高样品磁通钉扎能力和超导性能的效果.     

Tb$lt;sub$gt;0.3$lt;/sub$gt;Dy$lt;sub$gt;0.6$lt;/sub$gt;Pr$lt;sub$gt;0.1$lt;/sub$gt;(Fe$lt;sub$gt;1-$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;Al$lt;sub$gt;$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;)$lt;sub$gt;1.95$lt;/sub$gt;合金的磁性、磁致伸缩和穆斯堡尔谱研究

系统研究了室温下Tb_0.3Dy_0.6Pr_0.1（Fe_1-xAl_x）_1.95 （x=0.05,0.1,0.15,0.2,0.25,0.3）合金中元素Al替代Fe对结构、磁性、磁致伸缩性能和自旋重取向的影响.测量结果发现,x<0.2时Tb_0.3Dy_0.6Pr_0.1（Fe_1-xAl_x）_1.95合金基本上是纯的单相,x=0.2时出现其他杂相,杂相随Al替代量的增加不断增多.随Al替代量x的增加,点阵常数a接近于线性增大,Curie温度T_C逐渐下降,而矫顽力H_c急剧下降.振动样品磁强计（VSM）测量发现,磁化强度M随Al替代量x的变化较为复杂.VSM计和磁致伸缩效应测量共同表明,少量Al的替代有利于降低磁晶各向异性,而且随着Al替代量x的增多磁致伸缩系数快速减小,x>0.15时巨磁致伸缩效应消失.穆斯堡尔效应研究发现,随Al含量的增加Tb_0.3Dy_0.6Pr_0.1（Fe_1-xAl_x）_1.95合金中易磁化轴可能在{110}面逐渐偏离了立方晶体的主对称轴,发生自旋重取向,从而引起合金宏观磁性、磁致伸缩性能的变化. 关键词： 磁致伸缩 立方Laves相 自旋重取向 穆斯堡尔谱     

Observation of giant magnetocaloric effect under low magnetic fields in EuTi_(1-x)Co_xO_3

The magnetic properties and magnetocaloric effect(MCE) in EuTi_(1-x)Co_xO_3(x = 0, 0.025, 0.05, 0.075, 0.1) compounds have been investigated. When the Ti~(4+) ions were substituted by Co2+ions, the delicate balance was changed between antiferromagnetic(AFM) and ferromagnetic(FM) phases in the EuTiO_3 compound. In EuTi_(1-x)Co_xO_3 system, a giant reversible MCE and large refrigerant capacity(RC) were observed without hysteresis. The values of -?S_M~(max) were evaluated to be around 10 J·kg~(-1)·K~(-1) for EuTi_(0.95)Co_(0.05)O_3 under a magnetic field change of 10 kOe. The giant reversible MCE and large RC suggests that EuTi_(1-x)Co_xO_3 series could be considered as good candidate materials for low-temperature and low-field magnetic refrigerant.     

钙钛矿锰氧化物(La_(1-x)Eu_x)_(4/3)Sr_(5/3)Mn_2O_7(x=0,0.15)的磁性和电性研究

通过传统固相反应法制备了钙钛矿锰氧化物(La1-xEux)4/3Sr5/3Mn2O7(x=0,0.15)多晶样品,并且对其磁性和电性进行了研究.磁性测量表明:随着温度的降低,样品经历了一个复杂的转变过程,在温度为T*时经历二维短程铁磁有序转变,在温度为TC时进入三维长程铁磁态.随着Eu的掺杂,T*和TC减小,并且样品(La0.85Eu0.15)4/3Sr5/3Mn2O7在低温区表现出自旋玻璃行为.电性质测量表明:在母体La4/3Sr5/3Mn2O7中La位掺杂Eu后电阻率明显变大,金属绝缘转变温度TMI降低,磁电阻峰值增大.这些影响归因于较小的Eu3+离子替代La3+离子导致平均离子半径减小,晶格发生畸变.此外,较小的Eu3+离子优先占据层间岩盐层的R-site,使La3+,Sr3+,Eu3+离子在(La0.85Eu0.15)4/3Sr5/3Mn2O7中的分布更加有序,所以x=0.15的样品的ρ-T曲线只有一个峰.     

The role of Bi2O3 as a network modifier and a network former in xBi2O3 · (1 − x)LiBO2 glass system

The effect of Bi₂O₃ on the glass transition temperature, electrical conductivity and structure of LiBO₂ glass has been investigated. T_g vs. composition curve shows three different linear regions, while there is an overall decrease in T_g with the increase in Bi₂O₃ content. The slope of these three straight lines is in a decreasing order. These results are interpreted in terms of the increase in the number of non-bridging oxygen atoms, substitution of Bi-O bond in place of B-O bond and change in Li⁺ ion concentration. The conductivity vs. composition curve exhibits two maxima which are interpreted in terms of the structural modification effect of Bi₂O₃ on LiBO₂ network and mixed-former effect, respectively. Results obtained from the XPS studies of the samples of composition x 0.005, have shown that the number of non-bridging oxygen atoms from B-O bond increases with the increase in Bi₂O₃ content. It has a maximum value at x = 0.003 where the conductivity has also exhibited a maximum value. Further increase of Bi₂O₃ content causes decrease in it. For higher Bi₂O₃ content (x * > 0.005), O 1s spectra of Bi₂O₃ has been separated out from that of Bi₂O₃. Bismuth ions have been substituted for boron ions as network former ions.     

The influence of different fabrication processes on characteristics of excess Bi2O3-doped 0.95 (Na0.5Bi0.5)TiO3–0.05 BaTiO3 ceramics

In this study, we will develop the influences of the excess x wt% (x=0, 1, 2, and 3) Bi₂O₃-doped and the different fabricating process on the sintering and dielectric characteristics of 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃ ferroelectric ceramics with the aid of SEM and X-ray diffraction patterns, and dielectric–temperature curves. The 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ ceramics are fabricated by two different processes. The first process is that (Na_0.5Bi_0.5)TiO₃ composition is calcined at 850 °C and BaTiO₃ composition is calcined at 1100 °C, then the calcined (Na_0.5Bi_0.5)TiO₃ and BaTiO₃ powders are mixed in according to 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions. The second process is that the raw materials are mixed in accordance to the 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions and then calcining at 900 °C. The sintering process is carried out in air for 2 h from 1120 to 1240 °C. After sintering, the effects of process parameters on the dielectric characteristics will be developed by the dielectric–temperature curves. Dielectric–temperature properties are also investigated at the temperatures of 30–350 °C and at the frequencies of 10 kHz–1 MHz.     

Oxygen permeability of La2Cu(Co)O4+δ solid solutions

Formation of the La₂Cu_1−xCo_xO_4+δ solid solutions with orthorhombic K₂NiF₄-type structure was found to be in the range of 0≤x≤0.30 at temperatures above 1270 K. Incorporating cobalt into the copper sublattice of lanthanum cuprate leads to increasing oxygen hyperstoichiometry and decreasing electrical conductivity. Thermal expansion coefficients of the La₂Cu_1−xCo_xO_4+δ (x=0.02–0.30) ceramics at 470–1100 K were calculated from the dilatometric data to vary in the range (12.2–13.2)×10⁻⁶ K⁻¹. Studying the dependence of oxygen permeation fluxes through La₂Cu(Co)O_4+δ on the membrane thickness demonstrated that the oxygen transport at the thickness values below 1 mm is limited by both surface exchange rate and bulk ionic conductivity. Oxygen permeability of the La₂Cu_1−xCo_xO_4+δ solid solutions was ascertained to increase with cobalt concentration at x=0.02–0.10 and to decrease with further dopant additions, indicating a participation of interstitial oxygen in the ionic transport.     

Preparation, characterization and oxide ion conductivity in U-substituted Bi4V2O11

A Bi₂V_{1 − x − y}U_xBi_yO_{5.5 + 0.5x − y} solid solution derived from Bi₄V₂O₁₁ has been prepared and characterized with x up to 0.125 for y = 0. Partial substitution of U⁶⁺ for V⁵⁺ in Bi₄V₂O₁₁ leads to the stabilization at room temperature of the high-oxide ion conducting γ-phase, in contrast with other M⁶⁺ dopants which stabilize the β-phase. The lower conductivity in U substituted system compared with BICUVOX.10 is attributed to its higher activation energy. Conductivity values and activation energies of the U substituted phases compare well with Bi₂UO₆.     

Shaped crystal growth and scintillating properties of Yb:(Gd,Lu)3Ga5O12 solid solutions

Shaped single crystals of (Lu_xGd_1−x)₃Ga₅O₁₂ (0.0x1.0) and (Yb_0.05Lu_xGd_0.95−x)₃Ga₅O₁₂ (0.0x0.9) were grown by the modified micro-pulling-down method. Continuous solid solutions with garnet structure and a linear compositional dependency of crystal lattice parameter in the system Yb:(Gd,Lu)₃Ga₅O₁₂ are formed. Measured optical absorption spectra of the samples show 4f–4f transitions related to Gd³⁺ ion at 275 and 310 nm, and also an onset of charge transfer transitions from oxygen ligands to Gd³⁺ or Yb³⁺ cations below 240 nm. A complete absence of Yb³⁺ charge transfer luminescence under X-ray excitation in any of the investigated samples was explained by the overlapping of charge transfer absorption of Yb³⁺ by that of Gd³⁺ ions. For specific composition of Lu_1.5Gd_1.5Ga₅O₁₂ an intense defect-host lattice-related emission, which achieve of about 40% integrated intensity compared with Bi₄Ge₃O₁₂, was found.     

Mixed electronic and ionic conductivity of LaCo(M)O3 (M=Ga, Cr, Fe or Ni).: V. Oxygen permeability of Mg-doped La(Ga, Co)O3−δ perovskites

The LaGa_1−x−yCo_xMg_yO_3−δ solid solutions with rhombohedrally-distorted perovskite structure were ascertained to form in the concentration range of 0≤y≤0.10 at x=0.60 and 0≤y≤0.20 at x=0.35–0.40. Increasing cobalt content results in increasing electrical conductivity and thermal expansion of the perovskites. Thermal expansion coefficients of the LaGa_1−x−yCo_xMg_yO_3−δ ceramics were calculated from the dilatometric data to vary in the range of 12.4–19.8×10⁻⁶ K⁻¹ at 300–1100 K. Doping La(Ga,Co)O_3−δ solid solutions with magnesium leads to increasing oxygen nonstoichiometry, electronic and oxygen ionic conductivity. Oxygen permeation fluxes through LaGa_1−x−yCo_xMg_yO_3−δ membranes were found to be limited by the bulk ionic conduction and to increase with magnesium concentration, being essentially independent of cobalt content.