Reactive plasma cladding of TiC/Fe cermet coating using asphalt as a carbonaceous precursor

A new process of preparing Ti-Fe-C composites powder for reactive plasma cladding, precursor carbonization-composition process, was developed. TiC/Fe cermet coatings were synthesized by reactive plasma cladding of the composite powder. XRD and SEM were employed to analyze the phase composition and microstructure of the composite powder and coating. The hardness and wear resistance of the coating was tested. Results show that: The compound powder prepared by precursor carbonization-composition process has very tight structure, which can avert the question of raw powder breaking-up in cladding process. The TiC/Fe cermet coating by reactive plasma cladding consists of alternate, laminated layers as following: the layers in which the round nanoscale TiC particles are dispersed within the α-Fe matrix and the layers of TiC accumulation. The TiC/Fe cermet coating by reactive plasma cladding shows superior hardness and wear resistance: The surface hardness of the TiC/Fe cermet coating is 68 ± 6 (HR30 N). In the same fretting conditions, the wear resistance of Ni60 coating is twelve times than that of the TiC/Fe cermet coating.     

Nanocomposite TiC/a-C：H film prepared on titanium aluminium alloy substrates by PSII assistant MW-ECRCVD

Thin films of titanium carbide and amorphous hydrogenated carbon have been synthesized on titanium aluminium alloy substrates by PSII assisted MW-ECRCVD with a mirror field. The microstructure, chemical composition and mechanical property were investigated. Using XPS and TEM, the films were identified to be a-C：H film containing TiC nanometre grains （namely, the so-called nanocomposite structure）. The size of TiC grains of nanocomposite TiC/DLC film is about 5 nm. The nanocomposite structure has obvious improvement in the mechanical properties of DLC film. The hardness of a-C：H film with Ti is enhanced to 34 G Pa~ while that of a-C：H film without Ti is about 12 G Pa, and the coherent strength is also obviously enhanced at the critical load of about 35N.     

Synthesis of transparent BaTiO3 nanoparticle/polymer composite film using DC field

Transparent BaTiO₃ nanoparticle/polymer composite films were synthesized from titanium-organic film and barium ion in aqueous solution under direct current (DC) field. Titanium-organic precursor was synthesized from titanium isopropoxide, acetylacetone and methacrylate derivative. The UV treatment was effective to increase the anti-solubility of the titanium-organic film during DC processing. BaTiO₃ nanoparticles were crystallized in the precursor films on stainless substrates without high temperature process, as low as 40°C. The crystallite size of BaTiO₃ increased with increasing reaction temperature from 40 to 50 °C at 3.0 V/cm. BaTiO₃ nanoparticles also grew in size with increasing reaction time from 15 min to 45 min at 3.0 V/cm and 50 °C. Transparent BaTiO₃ nanoparticle/polymer films were synthesized on stainless substrates at 3.0 V/cm and 50°C for 45 min.     

Controllable Formation of Niobium Nitride/Nitrogen‐Doped Graphene Nanocomposites as Anode Materials for Lithium‐Ion Capacitors

Niobium nitride/nitrogen‐doped graphene nanosheet hybrid materials are prepared by a simple hydrothermal method combined with ammonia annealing and their electrochemical performance is reported. It is found by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) that the as‐obtained niobium nitride nanoparticles are about 10–15 nm in size and homogeneously anchored on graphene. A non‐aqueous lithium‐ion capacitor is fabricated with an optimized mass loading of activated carbon cathode and the niobium nitride/nitrogen‐doped graphene nanosheet anode, which delivers high energy densities of 122.7–98.4 W h kg^?1 at power densities of 100–2000 W kg^?1, respectively. The capacity retention is 81.7% after 1000 cycles at a current density of 500 mA g^?1. The high energy and power of this hybrid capacitor bridges the gap between conventional high specific energy lithium‐ion batteries and high specific power electrochemical capacitors, which holds great potential applications in energy storage for hybrid electric vehicles.     

Thermal properties of graphene and multilayer graphene: Applications in thermal interface materials

We review the thermal properties of graphene and multilayer graphene, and discuss graphene’s applications in thermal management of advanced electronics and optoelectronics. A special attention is paid to the use of the liquid-phase-exfoliated graphene and multilayer graphene as the fillers in the thermal interface materials. It has been demonstrated that addition of an optimized mixture of graphene and multilayer graphene to the composites with different matrix materials produces the record-high enhancement of the effective thermal conductivity at the small filler loading fraction (f≤10 vol%). The thermal conductivity enhancement due to the presence of graphene in the composites has been observed for a range of matrix materials used by industry. The hybrid composites where graphene is utilized together with metallic micro- and nanoparticles allow one to tune both the thermal and electrical conductivity of these materials. Theoretical considerations indicate that the graphene-based thermal interface materials can outperform those with carbon nanotubes, metal nanoparticles and other fillers owing to graphene’s geometry, mechanical flexibility and lower Kapitza resistance at the graphene–base material interface.     

Synthesis of amorphous carbon nanoparticles and carbon encapsulated metal nanoparticles in liquid benzene by an electric plasma discharge in ultrasonic cavitation field

A newly-developed method permits an electric plasma discharge to occur with relatively low electric power in insulating organic solutions due to the presence of an ultrasonic cavitation. A stable electric plasma could be generated in an ultrasonic cavitation field containing a thousand tiny activated bubbles, in which the electric conductivity could be improved due to formed radicals and free electrons, using copper electrodes and a titanium ultrasonic horn. This method allowed us to synthesize pyrolytic amorphous carbon nanoparticles smaller than about 30 nm in diameter from benzene liquid. In addition, we synthesized TiC nanoparticles about 50-150 nm in size, and copper nanoparticles smaller than 10 nm, which were encapsulated in multilayered graphite cages. Finally, we used GC-MS and MALDI-TOF-MS to observe and analyze the polymerized compounds and the degree of polymerization of the benzene liquid after the plasma treatment.     

Two-photon polymerization of titanium-containing sol–gel composites for three-dimensional structure fabrication

In this work, we have synthesized and characterized a novel, titanium-containing hybrid material that can be structured three-dimensionally using two-photon polymerization. We investigate the effect on the structurability of the increase of titanium isopropoxide and methacrylic acid in this photosensitive composite. We show that while it is possible to make transparent thin films with a titanium isopropoxide molar content as high as 90%, three-dimensional structures can be made only when the titanium isopropoxide molar content is less than 50%. We measure the refractive index of films with different titanium isopropoxide: methacrylic acid concentrations and we show that while the refractive index increases linearly with the titanium isopropoxide, the increase of the methacrylic acid content does not affect the refractive index of the material.     

乙炔气体流量对纳米TiC类金刚石复合膜的化学结构及力学性能影响

采用离子注入与反应磁控溅射相结合的方法在钛合金及硅片基体表面上制备了纳米TiC类金刚石(DLC)复合膜.通过纳米压痕技术检测了薄膜的纳米硬度，显微划痕试验评估了薄膜的结合力.通过X射线光电子能谱及X射线衍射表征了薄膜的化学结构.结果表明，通过改变C₂H₂气体流量，可以达到控制薄膜中钛原子含量的目的，合适的C₂H₂气体流量可以在DLC膜中形成较多的纳米TiC晶粒，形成DLC包覆TiC晶粒的复合结构，使DLC膜力学性能得到明显提高.另外，划痕试验表明掺钛、先注入后沉积工艺都使薄膜的结合力得到了较大提高. 关键词： 纳米TiC类金刚石复合膜 类金刚石膜 力学性能     

Core–shell nanostructures and nanocomposites of Ag@TiO2: effect of capping agent and shell thickness on the optical properties

Two different shell-forming reagents viz. titanium isopropoxide and titanium hydroxyacylate, have been employed to obtain core–shell nanostructures of Ag@TiO₂. However, nanocomposites were formed when the shell-forming agent, titanium isopropoxide, was added before breaking the micelles. Titanium hydroxyacylate has been used for the first time as a shell-forming agent which resulted in uniform core–shell structures of Ag@TiO₂ with core diameter ranging from 10 to 40 nm and a shell thickness of 10–50 nm. The low rate of hydrolysis of titanium hydroxyacylate than titanium isopropoxide (used in other methods) appears to be responsible for the uniform shell thickness. The presence of capping agent (2-mercaptoethanol) disrupts the formation of a uniform shell structure of Ag@TiO₂. HRTEM, IR, and XPS studies of Ag@TiO₂ synthesized using capping agent show the formation of Ag₂S coated with an amorphous layer of TiO₂. A red shift of 25 and 10 nm was observed in the surface plasmon band of silver for Ag@TiO₂ core–shell structures (compared with that of silver nanoparticles) synthesized using titanium hydroxyacylate and titanium isopropoxide, respectively. The presence of capping agent (2-mercaptoethanol) masks the surface plasmon peak. Photoluminescence studies show an increase in the emission intensity for the core–shell structures when compared to that of TiO₂ nanoparticles.     

Synthesis of titanium boride nanoparticles and fabrication of flexible material for radiation shielding

A numerical simulation for a radio frequency (RF) thermal plasma torch was carried out to identify the temperature and velocity distributions and determine the optimal design of a plasma system based on the coil turn and torch inner diameter parameters. Then, the optimized conditions of five coil turns and a torch inner diameter of 64 mm were applied to synthesize titanium boride nanoparticles. The major crystal structure of the synthesized titanium boride nanoparticles was TiB₂, with TiB as a minor phase and an average particle size of 42 nm. Subsequently, the gamma-ray shielding performance was analyzed using synthesized titanium boride nanoparticles. Flexible shielding materials were fabricated using a hydrogel to load the synthesized nanoparticles. The attenuation coefficient of the titanium boride nanoparticle flexible material was 0.238 cm⁻¹, and the half-value layer was 2.91 cm.     

Synthesis of nanoparticles in an atmospheric pressure glow discharge

Nanopowders are produced in a low temperature, non-equilibrium plasma jet (APPJ), which produces a glow discharge at atmospheric pressure, for the first time. Amorphous carbon and iron nanoparticles have been synthesized from Acetylene and Ferrocene/H₂, respectively. High generation rates are achieved from the glow discharge at near-ambient temperature (40–80°C), and rise with increasing plasma power and precursor concentration. Fairly narrow particle size distributions are measured with a differential mobility analyzer (DMA) and an aerosol electrometer (AEM), and are centered around 30–35 nm for carbon and 20–25 nm for iron. Particle characteristics analyzed by TEM and EDX reveal amorphous carbon and iron nanoparticles. The Fe particles are highly oxidized on exposure to air. Comparison of the mobility and micrograph diameters reveal that the particles are hardly agglomerated or unagglomerated. This is ascribed to the unipolar charge on particles in the plasma. The generated particle distributions are examined as a function of process parameters.     

Synthesis and characterization of carbide nanosheets by a template-confined reaction

Titanium carbide (TiC) and niobium carbide (NbC) nanosheets were synthesized by reacting few-layer graphene (FLG) with volatile titanium and niobium iodides, respectively. The successful synthesis was confirmed by XRD, SEM, TEM, and Raman analyses. The synthesized TiC and NbC nanosheets were polycrystalline, with average crystallite sizes of 8 and 12?nm, respectively. The results suggested that FLG acted as the template to confine the reaction and defined the overall morphology of the synthesized nanosheets. This method could be extended to synthesize a variety of other carbide nanosheets.     

Site‐specific fabrication of graphitic microporous carbon terminated with ordered multilayer graphene walls

The site‐specific fabrication of metal‐incorporated graphitic microporous carbon terminated by highly ordered multilayer graphene walls via an ambient‐temperature vacuum‐based process is presented for the first time. Sputtering of Cr nano‐particles on the ultrathin amorphous carbon film manifests a dual effect of activation via dry‐etching by the sputtering plasma and of ‘knock‐on' inelastic collision between nanoparticles and C atoms for structural ordering. This novel and simple method is very useful for fabricating high surface area carbon nanostructures for hydrogen storage and clean energy applications. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Carbon nanosheets by microwave plasma enhanced chemical vapor deposition in CH4-Ar system

We employ a new gas mixture of CH₄-Ar to fabricate carbon nanosheets by microwave plasma enhanced chemical vapor deposition at the growth temperature of less than 500 °C. The catalyst-free nanosheets possess flower-like structures with a large amount of sharp edges, which consist of a few layers of graphene sheets according to the observation by transmission electron microscopy. These high-quality carbon nanosheets demonstrated a faster electron transfer between the electrolyte and the nanosheet surface, due to their edge defects and graphene structures.     

Dual functions of TiC nanoparticles on tribological performance of Al/graphite composites

In this study, the effect of TiC nanoparticles as a reinforcement on the mechanical and tribological properties of Aluminum-based self lubricating composite was investigated. The microstructure, relative density, hardness, and tribological properties of Al/graphite and Al/TiC/graphite composites were examined as a function of graphite content. The tribo-surfaces of the samples were analyzed using SEM and EDS elemental mapping. The results indicated that the addition of TiC nanoparticles not only decreased the wear rate and coefficient of friction of the composites, but also facilitated the formation of a stable graphite layer at longer sliding distances and high sliding velocities by forming a durable graphite/TiC composite on the tribo-surface. Therefore, the stability of graphite layer can be considered as a possible cause for decrease in wear rate of the Al/TiC/graphite composite.     

CVD合成的掺杂BNx-石墨烯纳米复合材料:结构和发光性能

用B₄C为硼源,利用CVD系统在N₂-H₂等离子体中合成了掺杂BN_x纳米棒,接着在掺杂BN_x纳米棒表面用CH₄生长了石墨烯纳米片,制备出掺杂BN_x-石墨烯三维纳米复合材料。一系列表征结果说明合成的纳米复合材料由C和O共掺杂的BN_x纳米棒和石墨烯纳米片组成,其形成与碳氢基团的转换和掺杂BN_x纳米棒的形变在石墨烯纳米片中产生的应力有关。室温发光性能表明石墨烯纳米片对掺杂BN_x纳米棒的紫外光和绿光有明显的猝灭作用,起源于掺杂BN_x-石墨烯界面上的电荷转移和电子散射。     

Improvement in thermo mechanical and optical properties of in situ synthesized PMMA/TiO2 nanocomposite

In this paper, transparent thin films of nano titania filled Poly(methyl methacrylate) (PMMA) composites were synthesized by solvent casting method using tetra hydro furan as a solvent, with in situ nonaqueous ‘sol-gel’ transformation involving the mixing of titanium isopropoxide (as sol-gel precursor) and methanol. The present research work is focused at studying the effect of titania loading on optical and mechanical behavior of transparent nano hybrid thin films. The effect of nano Titanium dioxide (TiO₂) loading on PMMA morphology was studied by using a scanning electron microscope (SEM). Bowl shaped structures were obtained in pure PMMA thin film, which were deformed on incorporation of TiO₂ nanoparticles. This nanocomposite exhibits enhanced optical and mechanical properties. The peak of UV absorption is blue shifted to 261 and 266?nm with the incorporation of TiO₂. At this wavelength, the absorption is increased up to approximately 397%. The nanocomposites exhibit increased tensile strength up to 40% and modulus up to 16%. Tg of PMMA increased from 84.8 to 86.7?°C on adding 1.25% TiO₂ nanoparticles.     

Preparation of graphene on Cu foils by ion implantation with negative carbon clusters

We report on few-layer graphene synthesized on Cu foils by ion implantation using negative carbon cluster ions,followed by annealing at 950?C in vacuum.Raman spectroscopy reveals IG/I2Dvalues varying from 1.55 to 2.38 depending on energy and dose of the cluster ions,indicating formation of multilayer graphene.The measurements show that the samples with more graphene layers have fewer defects.This is interpreted by graphene growth seeded by the first layers formed via outward diffusion of C from the Cu foil,though nonlinear damage and smoothing effects also play a role.Cluster ion implantation overcomes the solubility limit of carbon in Cu,providing a technique for multilayer graphene synthesis.     

Magnetic Nanocomposites Formed by FeNi3 Nanoparticles Embedded in Graphene. Application as Supercapacitors

A general family of magnetic nanocomposites formed by FeNi₃ ferromagnetic nanoparticles (NPs) embedded in a graphitized carbon matrix is reported. The soft chemical approach used relies on the catalytic effect of the NPs resulting from the thermal decomposition of the layered double hydroxide precursor, which acts as a multilayered nanoreactor enabling the formation of a range of carbon nanoforms (CNFs). This is followed by acid treatment of the as‐prepared nanocomposites to isolate the different CNFs formed. These range from carbon nano‐onions to graphene depending on the temperature of the thermal decomposition. This synthetic process paves the way for the rational design of metal–carbon nanocomposites with controllable composition as precursors of nanocarbons or even graphene. The coexistence of metal NPs and nanostructured carbon is a major source of applications. As a proof of concept, the electrochemical performance of these metal–carbon hybrid supercapacitors is studied under high discharging current densities and they exhibit high values of specific capacitance and excellent rate capabilities.     

Surface decoration of carbon nanosheets with amino-functionalized organosilica nanoparticles

Carbonaceous nanosheets decorated with amino-functionalized organosilica nanoparticles have been synthesized by a direct pyrolysis of betaine at 400 °C in air, followed by a simple surface treatment with ([3-(2-aminoethylamino) propyl]trimethoxysilane under reflux conditions. Both pristine and organosilica modified carbon nanosheets (OMCNs), were characterized by Fourier-transform infrared (FTIR), Raman, and electron paramagnetic resonance (EPR) spectroscopies, transmission electron microscopy and thermal analysis methods. The experimental data reveal a dramatic increase in the number of radical centers on the surface of the developed OMCN hybrid. The organosilica nanoparticles, ranging in size between 3 and 15 nm, are spherical and homogenously anchored on the surface of carbon nanosheets. The formation of COSi bridges between carbon sheets and the organosilica nanoparticles has been supported by FTIR and EPR. These nanoparticles are bound to the nanosheet surface together with individual functional organosilane groups at a spacing of about 4 Å distance. The final hybrid is the complex nanosystem composed of 2D carbon nanosheets, spherical organosilica nanoparticles and immobilized amino organosilane molecules.