编码成象技术用于提高针孔成象空间分辨率

本文采用编码成象技术处理针孔成象,提高其空间分辨率.采用反投影解码技术,对针孔成象的分辨率进行了计算,结果表明,可将10μm的针孔成象空间分辨率提高到3μm左右.最后对字母“C”图象进行模拟计算,经反演后,可以得到与原图象相近的图象.     

Near field imaging in microwave regime using double layer split-ring resonator based metamaterial

A planar metamaterial structure consisting of two layers of split-ring resonator (SRR) arrays is demonstrated to form the image of a point source with subwavelength resolution. The source frequency is swept through the resonance gap of the metamaterial layers and the lateral field intensity distribution is recorded on the transmission side of the metamaterial. When the source is tuned to the resonance frequency of SRRs, the metamaterial acts as a high permeability medium and a distinct image with subwavelength resolution in the lateral direction is obtained. Increasing the distance between the individual SRR layers reduces the interlayer coupling, and the intensity and spatial resolution of the image decrease rapidly.     

杆箍缩二极管X射线焦斑的成像法测量

 X射线源的焦斑尺寸是反映杆箍缩二极管射线源成像性能的重要参数。利用针孔成像法对MeV级脉冲X射线源的焦斑进行了2维图像测量。厚针孔采用直孔段加单锥体结构,直孔段孔径为0.2 mm。对于0.5 MeV的X射线,5倍成像倍率下调制传递函数值为0.5时空间分辨达到2.0 lp·mm^-1。图像采集系统由闪烁体、物镜和CCD相机组成,物镜的成像倍率约0.34。实验结果经过模糊校正后,得到了焦斑的图像和调制传递函数。根据调制传递函数值为0.5时对应的空间频率值,给出X射线源焦斑的尺寸。阳极杆直径为1.2 mm时,X射线源焦斑的高斯分布等效直径为0.86 mm。     

波状结构二维光子晶体近场亚波长成像的研究

研究了波状结构二维光子晶体(2DPC)在红外波段的负折射近场成像,对其等频面进行了分析,指出波状结构二维光子晶体无法实现负折射远场成像的原因在于缺少与入射介质等频面相匹配的光子晶体圆形等频面,所用的矩形等频面使波状膜层二维光子晶体不可避免地具有各向异性特征,进而将成像限制在近场范围内。采用时域有限差分(时域有限差分)方法模拟了不同厚度的波状结构二维光子晶体近场成像效果,当厚度为两倍栅格常量时,单光源的成像分辨力为0.28λ,达到亚波长分辨效果。分辨力随着光源逐渐远离近场范围而降低,而像点的位置基本不随光源距离和光子晶体厚度的变化而改变。双光源的成像模拟进一步验证了波状结构二维光子晶体的近场亚波长成像能力,分辨力达到0.35λ,但成像质量受光子晶体厚度变化的影响较大。     

Subwavelength imaging enhancement through a three-dimensional plasmon superlens with rough surface

In this Letter we investigate the subwavelength imaging of a three-dimensional plasmon superlens based on the full vector wave simulations of optical wave propagation and transmission. The optical transfer functions are computed. Comparisons are made between the results of lenses with flat and periodic/random rough surfaces. We also study the problem of practical imaging system geometry using laser as an illumination source. Results show that the lens with periodic or random roughness can reduce the field interference effects, and provide improved focus on the transmission field and the Poynting flux. We illustrate that the subwavelength roughness in a plasmon lens can enhance the image resolution over a flat lens for both matched and unmatched permittivity conditions. The enhancement of resolution occurs because the introduced subwavelength roughness can amplify the evanescent wave components and suppress the surface plasmon resonance peaks.     

Study of scattering patterns and subwavelength scale imaging based on finite-sized metamaterials

A metamaterial slab, used as a superlens in a subwavelength imaging system, is frequently assumed homogeneous. It is the bulk properties of the metamaterial which are responsible for the resolution of the transferred information in the image domain, as a result of high transverse wave-vector coupling. However, how in a discretized metamaterial, individual meta-atoms (i.e., the meta-elements composing a negative index metamaterial slab) contribute to the imaging process is still actively studied. The main aim of this paper is to investigate the consequences of using only a few meta-atoms as a negative index slab-equivalent for subwavelength scale imaging. We make a specific choice for a meta-atom and investigate its resonant scattering patterns. We report on how knowledge of these 3D scattering patterns provides a means to understand the transfer of high spatial frequencies and assist with the design an improved negative index slab.     

FDTD study of subwavelength imaging by a photonic crystal slab

The problem of subwavelength imaging via a photonic crystal slab lens made of two-dimensional (2D) square arrays of parallel dielectric cylinders in air is studied and discussed theoretically. The finite-difference time-domain method is employed to investigate the unique features of imaging by such lens. We confirm earlier findings that a photonic crystal slab lens can provide the imaging of a point source. By analysing the transmission properties of the proposed structure, we demonstrate that inside the all-angle negative refraction, there are some favourable directions for waves to travel. We show that the surface termination of the photonic crystal is a key parameter to obtain a good quality image. The super-resolution of two sources separated by a distance less than the wavelength is also considered. It is shown that the achievable resolution is limited by the slab length.     

Off-Axis Imaging in Keel-Edge Pinhole Single Photon Emission Computed Tomography System Based on Monte Carlo Simulation

Monte Carlo simulation is applied to investigate the off-axis effect in keel-edge pinhole single photon emission computed tomography imaging.Aiming at finding the effective Geld of view(FOV) for imaging,we simulate point source in off-axis imaging(0,4,8 and 12 mm from the central rotation axis) of different collimator designs(channel height with 1.38,1 and 0.5 mm) with a fixed aperture diameter.Tradeoff curves of rms resolution and sensitivity are plotted to determine the effective FOV for different channel height pinhole collimators.The parameterized model can be further incorporated into image reconstruction algorithms,which compensates for the off-axis effect and is used as a reference for multi-pinhole design.     

Three-dimensional source reconstruction with a scanned pinhole camera

We present a simple reconstruction algorithm for three-dimensional (3D) incoherent source distributions imaged by a laterally scanned pinhole camera. We consider digital sampling of multiple pinhole images for 3D reconstruction and implement an experimental demonstration with lateral resolution of 2x10(-3) rad and longitudinal resolution of approximately 0.14z(2) m , where z is the object-to-pinhole distance in meters.     

Ultimate limit of resolution of subwavelength imaging devices formed by metallic rods

It is demonstrated that the ultimate physical limit of resolution of novel imaging devices based on arrays of metallic rods is determined by the skin depth of the metal. Our theoretical and numerical results show that wire medium lenses may provide a unique solution for subwavelength imaging at frequencies up to the terahertz range and may enable image formation at a significant distance from the source plane.     

基于CdZnTe像素阵列探测技术的伽玛源成像

根据高能射线针孔成像理论,采用CdZnTe像素阵列探测器建立了直接成像探测模式的伽玛源针孔探测系统。测试分析了CdZnTe像素阵列探测器的能量分辨力及峰值效率,讨论研究了针孔成像探测系统的调制传递函数和附加噪声特性,测试获得直径5mm137Cs源的探测图像,采用Lucy-Richardson迭代算法得到了137Cs源的复原图像。实验结果表明:CdZnTe探测器对662keV137Cs源的能量分辨力为6.25%～7.50%,峰值效率65.0%～72.5%;成像系统探测图像存在一定扩散现象,所采用的Lucy-Richardson迭代复原算法能较好地修正图像扩散,提高探测图像中心区域细节分辨力;估算所得137Cs源尺寸误差约0.5mm,所建立的CdZnTe针孔成像探测系统能有效得到小尺寸伽玛源的辐照强度分布及尺寸信息。     

一种有效提高太赫兹时域光谱装置成像空间分辨率的方法

太赫兹波成像技术一个最显著的制约因素是其有限的空间分辨率。提出通过在样品前加小孔的方法来提高传统太赫兹时域光谱装置成像的空间分辨率。采用在样品前约2 mm处加直径为0.5 mm小孔的方法使成像的空间分辨率从1.276 mm提高到0.774 mm,提高0.502 mm,约39％。通过这个简单的方法在传统的太赫兹时域光谱成像装置上实现了空间分辨率从毫米量级到亚毫米量级的提高。聚乙烯板上直径为1 mm的小孔被作为成像的研究对象,分别采用传统的太赫兹时域光谱装置对样品进行直接成像和在样品前约2 mm处加直径为0.5 mm的小孔后对样品成像两种方式,并采用损失成像中信噪比较好的能量损失成像,对比两种方式得到的样品的太赫兹像,结果显示聚乙烯板上小孔的边界加小孔后成像比不加小孔直接成像明显清晰。证实了在样品前加小孔可以有效的提高太赫兹成像系统的空间分辨率。从理论上对通过在样品前加小孔提高系统空间分辨率的方法进行了分析,指出小孔尺寸越小,系统的空间相干长度越大,空间分辨率越高,但同时太赫兹信号的强度会相应减小。该方法可以简单有效的提高太赫兹时域光谱装置成像的空间分辨率,从而进一步拓展太赫兹谱成像技术的应用领域。     

Imaging enhancement of a photonic crystal superlens due to a surface mode with a specific dispersion

We study the imaging process for a photonic crystal slab lens with a surface defect by the finite-difference-time-domain (FDTD) method. We demonstrate an odd surface mode with a specific dispersion curve in this system. The dispersion curve has an extreme point, which is corresponding to a slow light. If the working frequency is chosen at this extreme point the subwavelength resolution of image will be enhanced. Moreover, the subwavelength resolution of image is very sensitive to the position of this extreme point in the dispersion diagram. Longer interaction time and better field distribution may give a qualitative physical understanding for the enhancement of imaging quality.     

X光能点、放大倍率及针孔尺寸对空间分辨的影响

X光针孔成像是惯性约束聚变(ICF)研究中重要的诊断方法,对其点扩散函数的计算可用于图像重建和系统空间分辨的判断。对菲涅耳衍射公式进行了化简,分析了X光能点、针孔尺寸及放大倍率对针孔点扩散函数的影响。实验在保证成像能获得足够高信噪比的条件下,通过模拟获得在最佳空间分辨时所要的针孔大小、放大倍率和X光能点等参数。在流体力学不稳定性的静态样品定标实验中,通过模拟获得了针孔的调制传递函数(MTF),结合实验测量的结果反推获得分幅相机本身的MTF值。同时采用测刀边函数的方法获得了分幅相机本身的刀边函数,进而得到相机在各空间频率下的MTF值。两种方法得到的分幅相机MTF值一致,验证了通过菲涅耳衍射模拟X光针孔成像的可行性。     

Resolution enhancement by subtraction of confocal signals taken at different pinhole sizes

Subtractive imaging in confocal fluorescence light microscopy is based on the subtraction of a suitably weighted widefield image from a confocal image. An approximation to a widefield image can be obtained by detection with an opened confocal pinhole. The subtraction of images enhances the resolution in-plane as well as along the optic axis. Due to the linearity of the approach, the effect of subtractive imaging in Fourier-space corresponds to a reduction of low spatial frequency contributions leading to a relative enhancement of the high frequencies. Along the direction of the optic axis this also results in an improved sectioning. Image processing can achieve a similar effect. However, a 3D volume dataset must be acquired and processed, yielding a result essentially identical to subtractive imaging but superior in signal-to-noise ratio. The latter can be increased further with the technique of weighted averaging in Fourier-space. A comparison of 2D and 3D experimental data analysed with subtractive imaging, the equivalent Fourier-space processing of the confocal data only, and Fourier-space weighted averaging is presented.     

Thermal light subwavelength diffraction using positive and negative correlations

Ghost imaging and diffraction, inspired by the Hanbury Brown and Twiss effect, have potential in both classical and quantum optics regimes on account of their nonlocal characteristics and subwavelength resolution capabil?ity, and therefore have aroused particular interest. By extending the correspondence imaging scheme, we utilize the positive and negative intensity correlations in diffraction and perform subwavelength diffraction with pseudo-thermal light. In the experiment, a subwavelength(A/2) resolution and a better signal-to-noise ratio(10.3% improvement) are simultaneously achieved. The scheme can be utilized as a complement to the existing ghost imaging scheme to improve image quality.     

编码源中子成像的可见光模拟

采用编码源能大大提高中子成像的中子注量率,同时保持较高的准直比。对改进的均匀冗余矩阵编码源中子成像进行了计算机模拟并利用可见光进行了实验,初步验证了编码源中子成像的可行性,并且探索了各种在非理想条件下成像对图像质量的影响并提出了解决方法。结果表明,编码源配合相关算法能够较好地重建图像,反解后的物体尺寸及分辨能力与单孔成像相当,同时缩短了曝光时间。若物体与理想成像面存在着位置或旋转偏差,则投影大小与探测器CCD像素、解码矩阵尺寸便不能对齐,但仍可以通过对图像背景噪声标准差的计算来后期修正图像,也可以利用此方法在实验前确定编码源成像系统中理想成像面的位置,以确保图像质量。     

上海光源硬X射线相干衍射成像实验方法初探

相干X射线衍射成像方法是一种先进的成像技术,分辨率可达纳米量级.国际上大多数的同步辐射装置和自由电子激光装置都建立了该成像方法,并有将其作为主要成像技术的趋势.上海光源作为目前国内唯一的一台第三代同步辐射光源,尚未建立基于硬X射线的相干衍射成像实验平台.随着一批以波荡器为光源的光束线站投入使用,使得该方法的建立成为了可能.本文基于上海光源BL19U2生物小角散射线站,通过有效的光路设计,搭建了相干衍射实验平台,在12 keV和13.5 keV能量点均获得了硬X射线相干光束,并基于小孔衍射测量了入射光束的空间相干长度.该平台支持常规和扫描相干衍射实验模式,对小孔衍射图样及波带片扫描衍射图样实现了正确的相位重建,证明了该平台初步具备开展硬X射线相干衍射成像实验的能力.硬X射线相干衍射成像实验平台为国内首次建立,将为国内该实验方法的发展和应用提供有效的软硬件支持.     

源嵌入正折射率传输线介质板内的倏逝波和成像特性

 提出了点源嵌入正折射率介质板进行亚波长成像的新方法,分析了位于负折射率媒质里的正折射率介质板内外的电压倏逝波和电压传播波分布。正和负折射率媒质分别由2维未加载传输线和2维加载电感、电容传输线网络组成。微波电路和数值仿真结果都显示由于板内增大的倏逝场,在正折射率介质板的两个界面附近出现了很大的电压幅度,该结果证实了该正折射率介质板透镜能够恢复电压倏逝波,从而提高像的分辨率。     

快点火背光照相数值模拟

在激光惯性约束聚变实验研究中,诊断燃料层密度通常利用纳秒激光束辐照金属靶片产生特征X射线作为背光照明光源,对内爆球壳进行瞬态辐射照相,进而推断球壳内爆燃料层的密度。利用蒙特卡罗程序,对快点火X射线背光照相进行了研究,模拟了针孔成像中不同的针孔大小、障板厚度、背光能量对成像质量的影响,对于快点火实验中微米尺寸塑料小球,进行了诊断方案优化。模拟结果表明,综合考虑光通量及成像空间分辨,针孔半径为10 m时成像效果最佳;此时,采用2.7 keV的Mo背光源可以获得最佳的密度分辨。