AlGaN/GaN场板结构高电子迁移率晶体管的场板尺寸优化分析

对不同场板尺寸的AlGaN/GaN 场板结构高电子迁移率晶体管进行了研究,建立简化模型分析场板长度对沟道电场分布的影响.结果表明,调整钝化层厚度和场板长度都可以调制沟道电场的分布形状,当场板长度较小时,随着长度的增大器件击穿电压随之增加,而当长度增大到一定程度后器件击穿电压不再增加.通过优化场板长度,器件击穿电压提高了64%,且实验结果与模拟结果相符. 关键词： AlGaN/GaN 击穿电压 场板长度     

GaN FP-HEMTs中击穿电压与电流崩塌的关系

研究了钝化在抑制电流崩塌的同时，会引起HEMT器件击穿电压的下降.而采用场板结构的AlGaN/GaN场板HEMT器件(FP-HEMT)的击穿电压从46V提高到了148V，表明了场板对提高击穿电压有显著作用(3倍以上).接着，比较了FP-HEMT器件与常规HEMT器件，钝化后HEMT器件在应力前后的电流崩塌程度，得出了采用场板结构比之钝化对器件抑制电流崩塌有更明显作用的结论.从理论上和实验上都表明，采用场板结构能够很好解决提高击穿电压与抑制电流崩塌之间的矛盾. 关键词： GaN 场板 击穿电压 电流崩塌     

6H-SiC pn结紫外光探测器的模拟与分析

运用器件模拟软件模拟了pn结6H-SiC紫外光探测器的光响应灵敏度特性.讨论了不同掺杂浓度、不同器件结深对响应灵敏度的影响.对于p+n结器件，当受光面为p+层，且厚度约为0.2μm、浓度约为9×10.18cm-3、n层浓度约为1×1 0.16cm-3时，器件有较大的响应灵敏度，R=167.2mA/W；当受光面为n+ 层 ，且厚度约为0.2μm、浓度约为9×10.18cm-3、p层浓度约为1×10.16cm-3时，器件有较大的响应灵敏度，R=183.5mA/W.通过比较可知，模型能较好地反应实际情况，与实验数据符合较好. 关键词： 6H-SiC 紫外光探测 吸收系数 光响应灵敏度     

具有L型源极场板的双槽绝缘体上硅高压器件新结构

为了提高小尺寸绝缘体上硅(SOI)器件的击穿电压,同时降低器件比导通电阻,提出了一种具有L型源极场板的双槽SOI高压器件新结构.该结构具有如下特征:首先,采用了槽栅结构,使电流纵向传导面积加宽,降低了器件的比导通电阻;其次,在漂移区引入了Si O2槽型介质层,该介质层的高电场使器件的击穿电压显著提高;第三,在槽型介质层中引入了L型源极场板,该场板调制了漂移区电场,使优化漂移区掺杂浓度大幅增加,降低了器件的比导通电阻.二维数值仿真结果表明:与传统SOI结构相比,在相同器件尺寸时,新结构的击穿电压提高了151%,比导通电阻降低了20%;在相同击穿电压时,比导通电阻降低了80%.与相同器件尺寸的双槽SOI结构相比,新结构保持了双槽SOI结构的高击穿电压特性,同时,比导通电阻降低了26%.     

基于silvaco-TCAD的In0.53Ga0.47As/InP红外探测器的仿真

采用silvaco-TCAD研究In0.53Ga0.47As/InP SAGCM-APD光电探测器,对探测器的结构参数对器件的电场分布、击穿电压和贯穿电压的影响进行仿真分析。研究表明电荷层对器件内部电场起到更好的调节作用,但过高的电荷层面密度会导致APD探测器的击穿电压与贯穿电压之差减小。倍增层厚度的增加使击穿电压先减小后增高,贯穿电压线性增加,同时耗尽层宽度变大,使器件电容减小。当倍增区厚度1 μm、偏压为-5 V时,器件电容密度达到了4.5×10-17 F/μm。反向偏置电压为30 V时,APD探测器在1.31 μm和1.55 μm波长下的响应度分别达到1 A/W和1.1 A/W     

三级台面InGaAs/InP雪崩光电二极管的低边缘电场设计

设计了一种三级台面的InGaAs/InP雪崩光电二极管,解决了器件边缘电场和暗电流较高的问题.采用Silvaco Atlas器件仿真软件分析了边缘间距、电荷层掺杂浓度及厚度、倍增层掺杂浓度及厚度对器件性能的影响.仿真结果表明,本文设计的三级台面器件在边缘间距为8μm时有最优器件尺寸和较低边缘电场.采用掺杂浓度为1×10~(17)cm~(-3)、厚度为0.2μm的电荷层和掺杂浓度为2×10~(15)cm~(-3)、厚度为0.4μm的倍增层,成功将高电场限制在中心区域,使得反偏电压40V时的边缘电场降低至2.6×105V/cm,仅为中心电场的1/2,增强了器件的抗击穿能力.此外,本文设计的器件在0.9 V_(br)时的暗电流降低至9.25pA,仅为传统两级台面器件的1/3.     

SiCGe/SiC 异质结及其光电特性的MEDICI 模拟

在对SiC1-xGex三元合金主要特性的研究基础上，利用器件仿真器MEDICI模拟和分析SiCGe/SiC异质结光电二极管的光电特性。计算表明， SiC1-xGex 在Ge组分为0.3时与3C-SiC晶格失配较小，此时的SiCGe/SiC异质结对可见光和近红外光有较好的光谱响应。当P型SiC1-xGex层杂质浓度为1×1015cm-3、厚度1.6μm、x=0.3时，SiC1-xGex /SiC异质结光电二极管对0.52μm可见光有250mA/W左右的响应度，对0.7μm近红外光也有102mA/W左右的响应度。     

高击穿电压的AlGaN/GaN FP-HEMT研究与分析

就蓝宝石衬底上制备的AlGaN/GaN场板(field plate)HEMT器件、常规HEMT器件性能进行了分析对比.结果证明两种结构的器件直流参数变化不大，但是采用场板后器件的击穿电压从52V提高到了142V.在此基础上利用Sivaco软件对两种器件进行模拟仿真，深入分析了FP对器件击穿电压的影响.     

基于双电荷层结构的CMOS单光子雪崩二极管

基于180nm标准CMOS工艺,设计了一种能够有效提高光子探测效率的双电荷层结构的单光子雪崩二极管.该器件结构采用P电荷层和逆行掺杂的深N阱形成PN结,选取不同的P电荷层掺杂浓度,对击穿电压进行优化,当P电荷层浓度为1×1018cm-3时,击穿电压为17.8V,电场强度为5.26×105 V/cm.进一步研究发现N电荷层的位置会影响漂移电流密度和扩散电流密度.当在深N阱与N隔离层交界处掺杂形成N电荷层,即N电荷层掺杂峰值距离器件表面为2.5μm时,器件性能最优.通过Silvaco TCAD仿真分析得到:在过偏压1V下,波长500nm处的探测效率峰值为62%,同时在300～700nm范围内的光子探测效率均大于30%.     

高击穿电压的AIGaN/GaN FP-HEMT研究与分析

就蓝宝石衬底上制备的AlGaN／GaN场（field plate）HEMT器件、常规HEMT器件性能进行了分析对比．结果证明两种结构的器件直流参数变化不大，但是采用场板后器件的击穿电压从52V提高到了142V．在此基础上利用Sivaco软件对两种器件进行模拟仿真，深入分析了FP对器件击穿电压的影响．     

An AlGaN/GaN HEMT with a reduced surface electric field and an improved breakdown voltage

A reduced surface electric field in an AlGaN/GaN high electron mobility transistor(HEMT) is investigated by employing a localized Mg-doped layer under the two-dimensional electron gas(2-DEG) channel as an electric field shaping layer.The electric field strength around the gate edge is effectively relieved and the surface electric field is distributed evenly as compared with those of HEMTs with conventional source-connected field plate and double field plate structures with the same device physical dimensions.Compared with the HEMTs with conventional sourceconnected field plates and double field plates,the HEMT with a Mg-doped layer also shows that the breakdown location shifts from the surface of the gate edge to the bulk Mg-doped layer edge.By optimizing both the length of Mg-doped layer,L m,and the doping concentration,a 5.5 times and 3 times the reduction in the peak electric field near the drain side gate edge is observed as compared with those of the HEMTs with source-connected field plate structure and double field plate structure,respectively.In a device with V GS = -5 V,L m = 1.5 μm,a peak Mg doping concentration of 8×10 17cm-3 and a drift region length of 10 μm,the breakdown voltage is observed to increase from 560 V in a conventional device without field plate structure to over 900 V without any area overhead penalty.     

An AlGaN/GaN HEMT with enhanced breakdown and near-zero breakdown voltage temperature coefficient

An AlGaN/GaN high-electron mobility transistor (HEMT) with a novel source-connected air-bridge field plate (AFP) is experimentally verified. The device features a metal field plate that jumps from the source over the gate region and lands between the gate and drain. When compared to a similar size HEMT device with conventional field plate (CFP) structure, the AFP not only minimizes the parasitic gate to source capacitance, but also exhibits higher OFF-state breakdown voltage and one order of magnitude lower drain leakage current. In a device with a gate to drain distance of 6 μm and a gate length of 0.8 μm, three times higher forward blocking voltage of 375 V was obtained at V_GS=-5 V. In contrast, a similar sized HEMT with CFP can only achieve a breakdown voltage no higher than 125 V using this process, regardless of device dimensions. Moreover, a temperature coefficient of 0 V/K for the breakdown voltage is observed. However, devices without field plate (no FP) and with optimized conventional field plate (CFP) exhibit breakdown voltage temperature coefficients of -0.113 V/K and -0.065 V/K, respectively.     

Breakdown voltage model and structure realization of a thin silicon layer with linear variable doping on a silicon on insulator high voltage device with multiple step field plates

Based on the theoretical and experimental investigation of a thin silicon layer(TSL) with linear variable doping(LVD) and further research on the TSL LVD with a multiple step field plate(MSFP),a breakdown voltage(BV) model is proposed and experimentally verified in this paper.With the two-dimensional Poisson equation of the silicon on insulator(SOI) device,the lateral electric field in drift region of the thin silicon layer is assumed to be constant.For the SOI device with LVD in the thin silicon layer,the dependence of the BV on impurity concentration under the drain is investigated by an enhanced dielectric layer field(ENDIF),from which the reduced surface field(RESURF) condition is deduced.The drain in the centre of the device has a good self-isolation effect,but the problem of the high voltage interconnection(HVI) line will become serious.The two step field plates including the source field plate and gate field plate can be adopted to shield the HVI adverse effect on the device.Based on this model,the TSL LVD SOI n-channel lateral double-diffused MOSFET(nLDMOS) with MSFP is realized.The experimental breakdown voltage(BV) and specific on-resistance(R on,sp) of the TSL LVD SOI device are 694 V and 21.3 ·mm 2 with a drift region length of 60 μm,buried oxide layer of 3 μm,and silicon layer of 0.15 μm,respectively.     

Electric field modulation technique for high-voltage AlGaN/GaN Schottky barrier diodes

A novel structure of AlGaN/GaN Schottky barrier diode(SBD) featuring electric field optimization techniques of anode-connected-field-plate(AFP) and magnesium-doped p-type buried layer under the two-dimensional electron gas(2DEG) channel is proposed.In comparison with conventional AlGaN/GaN SBDs,the magnesium-doped p-type buried layer in the proposed structure can provide holes that can help to deplete the surface 2DEG.As a result,surface field strength around the electrode edges is significantly suppressed and the electric field along the channel is distributed more evenly.Through 2D numerical analysis,the AFP parameters(field plate length,L AFP,and field plate height,T AFP) and p-type buried layer parameters(p-type layer concentration,N P,and p-type layer thickness,T P) are optimized to achieve a three-equal-peak surface channel field distribution under exact charge balance conditions.A novel structure with a total drift region length of 10.5 μm and a magnesium-doped p-type concentration of 1 × 1017cm-3achieves a high breakdown voltage(V B) of 1.8 kV,showing 5 times improvement compared with the conventional SBD with the same device dimension.     

高跨导氢终端多晶金刚石长沟道场效应晶体管特性研究

基于多晶金刚石制作了栅长为4 pm的铝栅氢终端金刚石场效应晶体管.器件的饱和漏源电流为160 mA/mm,导通电阻低达37.85Ω·mm,最大跨导达到32 mS/mm,且跨导高于最大值的90%的栅压(V_(GS))范围达到3 V(-2 V≤V_(GS)≤-5 V).通过传输线电阻分析以及器件的导通电阻和电容-电压特性分析,发现氢终端多晶金刚石栅下沟道中的空穴面浓度达到了1.56×10~(13)cm~(-2),有效迁移率在前述高跨导栅压范围保持在约170 cm~2/(V·s).分析认为,较低的栅源和栅漏串联电阻、沟道中高密度的载流子和在大范围栅压内的高水平迁移率是引起高而宽阔的跨导峰和低导通电阻的原因.     

ZnO薄膜肖特基二极管的研制

采用直流反应磁控溅射的方法,在Al/Si(100)衬底上沉积了ZnO晶体薄膜.利用Al和Pt作为与ZnO接触的欧姆电极与肖特基电极,制作了ZnO薄膜肖特基二极管.X射线衍射测试结果表明ZnO薄膜具有高度的c轴择优取向.原子力显微分析表明:样品表面光洁平整,晶粒尺寸约100nm,扩展电阻分析表明ZnO薄膜的厚度为0.4μm,载流子浓度为1.8×1015 cm-3,此后的霍尔测试证实了这一结果并说明ZnO的导电类型为n型.室温下的I-V测试显示ZnO肖特基二极管具有明显的整流特性.Pt与n型ZnO接触的势垒高度为0.54eV.文中的ZnO肖特基二极管为首次研制的原型器件,其性能可以通过器件结构与制作工艺的进一步优化而得到改善.     

An AlGaN/GaN HEMT with reduced surface electric field and improved breakdown voltage

A reduced surface electric field in AlGaN/GaN high electron mobility transistor (HEMT) is investigated by employing a localized Mg-doped layer under the two-dimensional electron gas (2-DEG) channel as an electric field shaping layer. The electric field strength around the gate edge is effectively relieved and the surface electric field is distributed evenly as compared with those of HEMTs with conventional source-connected field plate and double field plate structures with the same device physical dimensions. Compared with the HEMTs with conventional source-connected field plate and double field plate, the HEMT with Mg-doped layer also shows that the breakdown location shifts from the surface of the gate edge to the bulk Mg-doped layer edge. By optimizing both the length of Mg-doped layer, L_m, and the doping concentration, a 5.5 times and 3 times the reduction in the peak electric field near the drain side gate edge is observed as compared with those of the HEMTs with source-connected field plate structure and double field plate structure, respectively. In a device with V_GS=-5 V, L_m=1.5 μm, a peak Mg doping concentration of 8× 10¹⁷ cm^-3 and a drift region length of 10 μm, the breakdown voltage is observed to increase from 560 V in a conventional device without field plate structure to over 900 V without any area overhead penalty.     

A new analytical model of high voltage silicon on insulator （SOI） thin film devices

A new analytical model of high voltage silicon on insulator (SOI) thin film devices is proposed, and a formula of silicon critical electric field is derived as a function of silicon film thickness by solving a 2D Poisson equation from an effective ionization rate, with a threshold energy taken into account for electron multiplying. Unlike a conventional silicon critical electric field that is constant and independent of silicon film thickness, the proposed silicon critical electric field increases sharply with silicon film thickness decreasing especially in the case of thin films, and can come to 141V/μm at a film thickness of 0.1μm which is much larger than the normal value of about 30V/μm. From the proposed formula of silicon critical electric field, the expressions of dielectric layer electric field and vertical breakdown voltage (V_B,V) are obtained. Based on the model, an ultra thin film can be used to enhance dielectric layer electric field and so increase vertical breakdown voltage for SOI devices because of its high silicon critical electric field, and with a dielectric layer thickness of 2μm the vertical breakdown voltages reach 852 and 300V for the silicon film thicknesses of 0.1 and 5μm, respectively. In addition, a relation between dielectric layer thickness and silicon film thickness is obtained, indicating a minimum vertical breakdown voltage that should be avoided when an SOI device is designed. 2D simulated results and some experimental results are in good agreement with analytical results.     

单晶金刚石氢终端场效应晶体管特性

基于微波等离子体化学气相淀积生长的单晶金刚石制作了栅长为2μm的耗尽型氢终端金刚石场效应晶体管,并对器件特性进行了分析.器件的饱和漏电流在栅压为-6 V时达到了96 mA/mm,但是在-6 V时栅泄漏电流过大.在-3.5 V的安全工作栅压下,饱和漏电流达到了77 mA/mm.在器件的饱和区,宽5.9 V的栅电压范围内,跨导随着栅电压的增加而近线性增大到30 mS/mm.通过对器件导通电阻和电容-电压特性的分析,氢终端单晶金刚石的二维空穴气浓度达到了1.99×10~(13)cm~(-2),并且迁移率和载流子浓度均随着栅压向正偏方向的移动而逐渐增大.分析认为,沟道中高密度的载流子、大的栅电容以及迁移率的逐渐增加是引起跨导在很大的栅压范围内近线性增加的原因.     

氧回旋离子束刻蚀化学气相沉积金刚石膜

利用非对称磁镜场电子回旋共振等离子体产生的氧回旋离子束刻蚀了化学气相沉积金刚石膜,研究了工作气压和磁电加热电压对金刚石样品附近的离子温度和密度的影响,并分析了金刚石膜的刻蚀和机械抛光效果。结果表明:当工作气压为0.03 Pa,磁电加热电压为200 V时,离子温度和密度最大,分别为7.38 eV和 23.81010 cm-3 。在此优化条件下刻蚀金刚石膜4 h后,其表面粗糙度由刻蚀前的3.525 m降为2.512 m,机械抛光15 min后,表面粗糙度降低为0.517 m,即金刚石膜经离子束刻蚀后可显著提高机械抛光效率。