纳米流体的激光自混频功率谱密度研究

纳米流体运动特性和颗粒参数的测量对纳米流体换热效率的研究具有重要意义。本文将激光自混频技术应用于纳米流体测量中,给出了自混频信号功率谱密度函数的表达式并实验研究其变化规律。研究结果表明,功率谱密度展宽具有佛克脱函数的形式。激光垂直入射流动样品池时,功率谱密度得到展宽,展宽程度随着定向流速的增大或束腰半径的减小而增大。激光倾斜入射流动样品池时,功率谱密度在展宽的同时还伴随多普勒峰移,其位置随着定向流速的增大或散射矢量与定向流速之夹角的减小而迁移至高频。     

基于带通滤波片的激光二极管自混频纳米颗粒干涉测量技术

激光二极管自混频技术可用于纳米颗粒的测量,采用多通道带通滤波技术分别测量了180,100,60nm三种纳米颗粒,获得自混频信号的频带功率谱(PS-BPF)。作为比较,对实时提取的自混频信号进行傅里叶变换得到功率谱密度(PSD)函数。分别对PSD函数和PS-BPF反演计算得到颗粒粒径分布。结果显示:两种方法得到的颗粒粒径分布基本一致,并与商用仪器测试结果吻合。对两种处理方式的模式矩阵分析表明,多通道带通滤波技术明显优于PSD函数处理方式。     

光纤受激布里渊增益谱线型特性分析

光纤受激布里渊效应是一种非常重要的光纤非线性效应,受激布里渊增益谱的线型特性,对于光谱分析、微波光子学、光纤传感等领域的应用,至关重要。针对增益谱线型特性研究,现有方法难以获取高信噪比的增益谱数据,介绍了一种采用两个窄线宽激光器的增益谱测量方法,其中一个激光器作为探针信号,另一个可调谐激光器作为泵浦信号在宽波段范围内进行推扫。得益于激光器的高信噪比单谱线特性,并利用偏振跟随特性,实现了高信噪比的受激布里渊增益谱测量。测量并分析了不同泵浦功率,对于谱型和线宽等受激布里渊增益特性的影响,特别是,直接实验测量了增益谱型从洛伦兹线型到高斯线型的演化,揭示了泵浦功率等影响受激布里渊增益水平的因素,对于增益谱线型的影响。实验发现,当泵浦功率超过15 dBm时,增益谱出现饱和效应,导致测量增益谱线宽开始随泵浦功率提高而展宽,难以直接测量得到高泵浦功率时的高斯线型的增益谱。提出通过归一化等校正处理,以获取受激布里渊增益谱与待测信号光谱的有效卷积信息,从而得到了近似为高斯线型的增益谱型;针对中间增益区域增益谱型较为复杂,缺少合适增益谱线型演化数学模型的难题,给出了一种基于k次洛伦兹函数拟合的谱型模型,描述从洛伦兹线型到高斯线型的完整演进过程。实验表明拟合效果良好,是一种行之有效的受激布里渊增益谱线型数学模型,可完整描述增益谱在不同增益时的线型。最后,探索了受激布里渊效应在光谱分析方面的应用,通过合理选择泵浦功率等手段,增益谱型为高斯线型时的光谱分光效果最佳,获取了0.2 pm分辨率的6314CA稳定光源的光谱,显示了光纤受激布里渊效应在超高分辨率光谱分析领域的巨大技术优势,而这对于新一代光网络的验证评估至关重要。     

InP/InGaAsP多量子阱自发辐射谱的解析函数

利用洛伦兹线型函数、高斯线型函数和Sech线型函数对InP/InGaAsP多量子阱自发辐射谱进行拟合,采用莱文贝格-马夸特算法,得到上述三种函数的解析表达式.研究结果表明:高斯线型光谱拟合函数的中心波长为1548.651nm,谱线半极大全宽度为61.42 nm,功率补偿为0.00212 mW,拟合优度为0.99191,残差平方和为2.26505×10~(-6).高斯线型拟合的拟合优度最大,残差平方和最小,且各数据点的残差值分布在±0.0001之间,分布比较均匀.高斯线型函数具有较高拟合度.     

基于吸收光谱的光程长度测量方法研究

基于吸收光谱的基本原理,通过计算比尔-朗伯定律数学表达式中的参数实现了光程长度的测量。分析了高斯线型、洛伦兹线型和Voigt线型,采用了Voigt线型对光谱信号进行拟合。研究了Voigt线型峰值计算方法、洛伦兹线宽计算和误差函数求解三个内容。利用可调谐半导体激光吸收谱技术(TDLAS)中的直接吸收谱技术测量了氧气的吸收光谱,得到拟合的光谱峰值数据。将峰值数据带入比尔-朗伯定律数学表达式中,计算出实验光程长度为66.55 cm。对比测量值66.04 cm,测量精度为0.78%,该方法用于光程长度测量是可行的。     

全频域下窄线宽激光器光谱线宽的分析

窄线宽激光器的线宽表征方式通常采用延时自外差法测量技术。该技术是通过延时光纤差拍产生一个与待测激光线宽相关的洛伦兹频谱,因此该频谱只具有单一的线宽表现形式。为了能够观察到激光器的线宽和频率噪声在其傅里叶频率分布下的完整特性,报道了一种基于β算法计算窄线宽激光器线宽的方法。该方法是结合频率噪声中的白噪声和1/f噪声分别诱导不同激光线型的理论,从而确定激光线宽。首先,对β算法的基本原理进行了详细的分析说明。通过基于维纳-辛钦定理,分析了窄线宽激光器不同频率范围内的频率噪声和激光线宽的依赖关系。阐明了在截止频率趋于0和无穷大的两个范围条件时,激光频谱特性从高斯线型向洛伦兹线型演变。同时推导出使两种线型转换的截止频率表达式,并将其转换为频率噪声函数,该函数定义为β分子线。此时频率噪声分量中高斯线型的总和即为激光线宽计算公式;其次,对窄线宽激光器的频率噪声和激光线型进行数值仿真。将通过OEwaves公司的OE4000互相关零差相位/频率噪声自动测试系统测得的频率噪声谱密度,带入β算法理论公式中。结果显示：1/f噪声导致激光呈现高斯线型,线宽随截止频率的增加而增大。而白噪声将导致洛伦兹线型,线宽不再随截止频率而改变。此外,在低频区域,频率噪声电平远大于其傅里叶频率,噪声调制系数较高,该部分噪声可以决定线宽大小。因此,高斯线型区域对应的频率噪声的积分,即为待测激光器的线宽;在高频区域,频率噪声电平与其傅里叶频率相差较小,频率波动较快,噪声对线宽影响可以忽略。并且频率带宽在截止频率范围内,计算的线宽误差较小。最后,实验上运用β算法对RIO公司的1 550 nm低噪声窄线宽激光器的频率噪声功率谱密度进行积分计算,成功获得了其不同傅里叶频率分布下对应的激光线宽值。其中β分子线将频率噪声中的白噪声和1/f噪声分隔两部分：当频率噪声谱密度大于β分子线时,激光即为高斯线型,线宽随频率积分带宽的增加而减少;而频率噪声谱密度小于β分子线时,激光呈现洛伦兹线型,线宽为定值不再改变。同时为了对β算法进行实验验证,搭建了延迟光纤为50 km、移频频率为60 MHz的延时自外差法测量系统。对注入电流为110 mA的RIO 1 550 nm低噪声窄线宽激光器的线宽进行实验测量,测量结果表明激光线宽为1.8 kHz,与上述β算法中2.8 kHz的频率带宽积分结果一致。充分证明了此算法的准确性。β算法可以对任意类型的窄线宽激光器进行线宽表征,对窄线宽激光器的研究具有重要意义。     

激光感生双光栅中频谱分辨率的研究

研究了用于测量两束光频差的时间延迟激光感生双光栅的频谱分辨率，确定了当泵浦光具有高斯线型时四波混频信号的产生条件，此条件通过在可调谐的窄带激光和宽带激光间的拍频实验得到证实。     

近距离激光外差探测光学极限位移分辨率

通过统计理论和维纳-辛钦定理推导出激光外差探测系统光电流的功率谱函数,分析了光电流谱线分布与激光光源线宽、中频信号频率以及信号光相对本振光传输延迟时间的关系,修正了相关文献中光电流功率谱的理论公式.根据信号与噪声理论建立了激光线宽引起的相位噪声的一维概率分布模型,并据此得到了基于激光波长、探测距离以及激光线宽的极限位移分辨率的数学模型.对光电流的功率谱和外差光学极限位移分辨率进行了相关的数值仿真,结果表明延迟时间与相干时间的关系决定光电流谱线分布的情况.当激光波长为532 nm,激光线宽在1 kHz,探测距离为100 m时,光学极限位移分辨率为0.266 nm,相关文献中的实验数据与理论推导结果相符合.     

一级近似下的单模激光增益模型随机共振

把周期信号输入单模激光,对激光增益模型中的乘法噪声项取一级近似通过计算相关函数得到功率谱,发现输出信号是洛伦兹型的.信噪比随抽运噪声强度和量子噪声强度的变化均出现随机共振,但共振峰对应的噪声强度比零级近似下的小.     

Voigt线型函数及其最大值的研究

研究了多普勒和洛伦兹线型函数卷积形式的Voigt线型函数, 给出了它的最大值.结果表明, Voigt线型函数是关于中心频率的对称函数, Voigt线型函数的最大值由多普勒和洛伦兹线型函数的半宽度决定, 与中心频率无关, 且比洛伦兹和多普勒线型函数的最大值都小.提出了利用Voigt线型函数最大值和半宽度获得多普勒线型函数和洛伦兹线型函数的方法, 并利用Monte Carlo方法进行了验证. 关键词： Voigt线型函数 半宽度 最大值 傅里叶变换     

Power spectral density of self-mixing signals from a flowing Brownian motion system

An analytical expression for the power spectral density of the self-mixing signals from a flowing Brownian motion system irradiated by a focused Gaussian field is derived from the time autocorrelation function of the signals. The power spectral density is composed of two Voigt functions. An improved series summation method (SSM) is proposed to calculate the Voigt function. The characteristics of the power spectral density are analyzed according to the numerical results. The power spectral density can hopefully be used for measuring the flow velocity and the particle size.     

Simultaneous measurement of vibration amplitude and rotation angle based on a single-channel laser self-mixing interferometer

Based on a single-channel laser self-mixing interferometer,we present a new simultaneous measurement of the vibration amplitude and the rotation angle of objects that both affect the power spectrum containing two peaks of the interferometer signals.The fitted results indicate that the curve of the peak frequency versus the vibration amplitude follows a linear distribution,and the curve of the difference of the two-peak power values versus the angle follows a Gaussian distribution.A vibration amplitude with an error less than 3.0% and a rotation angle with an error less than 11.7% are calculated from the fitted results.     

激光自混合显微系统的设计及实验研究

论述了自混合干涉技术的发展历程,并引入了自混合干涉显微技术的实验原理和研究近展;建立了He—Ne激光自混合干涉实验装置系统,获得了稳定的激光功率输出。然后,对基于激光自混合干涉技术的显微镜进行了研究,并详细给出了该系统的设计原理、装调方法和实验结果,得到了玻璃小球的三维形体信息图像。系统达到的横向分辨力1μm,纵向分辨力为15nm。上述实验结果证明自混合显微镜在微小物体的高精度形貌成像方面有着很大的潜力。     

Measurement of the feedback coefficient by monitoring the power difference at power jump point in self-mixing vibration signal

This paper proposed a new method for measuring the feedback coefficient in the self-mixing interference. In experiment, the value of feedback coefficient is obtained by measuring the power difference at power jump point that based on the self-mixing vibration sensing system. It realized the measurement of feedback coefficient in range of 1–7.8 and shows a good agreement with the theoretical derivation and the corresponding simulation. Meanwhile, there is a good fitting result with the determination coefficient of 0.98 and line-width broadening factor of 3.245 respectively, which also realized measurement of feedback coefficient and line-width broadening factor at the same time.     

Self-mixing effect in Yb3+ doped DBR fiber laser with different linewidth enhancement factor

We present a self-mixing interference model approach to stimulate the self-mixing interference in YDBR fiber laser with optical self-mixing interference operating in the weak feedback regime. The self-mixing interference model includes Yb³⁺ doped fibers pumped at 920 nm, with distributed Bragg reflector mirrors at both fiber ends and external reflector. Using the quasi-analytical YDBR fiber laser model and self-mixing three-mirror cavity model, the output power expression is deduced and the Peak-to-Peak values and asymmetry values of self-mixing waveform at different linewidth enhancement factor have been studied in detail.     

Laser self-mixing interference fibre sensor

Fibre sensors exhibit a number of advantages over other sensors such as high sensitivity, electric insulation, corrosion resistance, interference rejection and so on. And laser self-mixing interference can accurately detect the phase difference of feedback light. In this paper, a novel laser self-mixing interference fibre sensor that combines the advantages of fibre sensors with those of laser self-mixing interference is presented. Experimental configurations are set up to study the relationship between laser power output and phase of laser feedback light when the fibre trembles or when the fibre is stretched or pressed. The theoretical analysis of pressure sensors based on laser self-mixing interference is indicated to accord with the experimental results.     

大气颗粒物多参数激光自混合传感的数值模拟与特性分析

基于颗粒物米氏散射特性、激光自混合三镜腔理论和激光器稳态条件,推导出在大气颗粒物光反馈下激光器频率、功率、线宽的理论表达式,建立了大气颗粒物光反馈下的激光自混合理论模型。同时,数值模拟和分析了大气颗粒物物理参数对激光自混合干涉信号的影响。结果表明,在一定粒径范围内,激光自混合反馈强度随大气颗粒物粒径增大先增大后减小,且反馈强度峰值出现的位置随颗粒物折射率实部的增大、虚部的减小向粒径较大处移动;自混合系统的外腔长度影响自混合干涉信号的波动深度,激光器输出光信号的幅值随外腔长度增大呈指数衰减;自混合干涉信号波动频率与大气颗粒物运动速度呈线性关系。分析结果对基于激光自混合效应的大气颗粒物多物理参数传感具有重要作用。     

Room-temperature terahertz detection based on CVD graphene transistor

We report the fabrication and characterization of a single-layer graphene field-effect terahertz detector, which is coupled with dipole-like antennas based on the self-mixing detector model. The graphene is grown by chemical vapor deposition and then transferred onto an Si O2/Si substrate. We demonstrate room-temperature detection at 237 GHz. The detector could offer a voltage responsivity of 0.1 V/W and a noise equivalent power of 207 n W/Hz1/2. Our modeling indicates that the observed photovoltage in the p-type gated channel can be well fit by the self-mixing theory. A different photoresponse other than self-mixing may apply for the n-type gated channel.