Kerr 介质中三能级原子与双模场非共振相互作用的量子统计性质

研究了Kerr介质中双模场与V型三能级原子的非共振相互作用. 对Cauchy-Schwartz不等式的研究表明,在两模场失谐量相等(δ₁=δ₂)条件下,当初始场强ξ一定而两模场的光子数差q减小时,场的非经典相关程度加强;q一定而ξ增大时,场的非经典相关程度减弱. 当Δδ=|δ₂-δ₁|≠0且q和ξ的取值一定时,随介质常量x的增大,光场两模间的非经典相关程度减弱,且Δδ的大小对这种非经典相关程度的减弱有重要影响. 对场的 关键词： Kerr介质 非共振相互作用 Cauchy-Schwartz不等式 场的二阶关联函数     

HOMs simulation and measurement results of IHEP02 cavity

In accelerator RF cavities, there exists not only the fundamental mode which is used to accelerate the beam, but also higher order modes(HOMs). The higher order modes excited by the beam can seriously affect beam quality, especially for the higher R/Q modes. 1.3 GHz low-loss 9-cell superconducting cavity as a candidate for ILC high gradient cavity, the properties of higher order mode has not been studied carefully. IHEP based on existing low loss cavity, designed and developed a large grain size 1.3 GHz low-loss 9-cell superconducting cavity(IHEP02cavity). The higher order mode coupler of IHEP02 used TESLA coupler's design. As a result of the limitation of the mechanical design, the distance between higher order mode coupler and end cell is larger than TESLA cavity.This paper reports on measured results of higher order modes in the IHEP02 1.3 GHz low-loss 9-cell superconducting cavity. Using different methods, Q e of the dangerous modes passbands have been obtained. The results are compared with TESLA cavity results. R/Q of the first three passbands have also been obtained by simulation and compared with the results of the TESLA cavity.     

Improved gyrotron cavity with high quality factor

For gyrotrons operating at the second harmonic of the electron cyclotron frequency cavities with high quality factors are needed. Up to now steep output tapers or abrupt output irises are used in order to provide a high reflection coefficient. Such circuits suffer from the problem of strong conversion to unwanted output modes. A promising possibility to achieve a high reflection at the cavity output (and thus a high quality factor) combined with high mode purity is the use of a rounded iris and an optimized nonlinear taper with very low unwanted mode conversion at the output of the resonator.     

基于回音壁模式微球腔的PDH稳频技术

光学微球腔因其回音壁模式可获得极高的品质因数而受到广泛关注.本文分析了Fabry-Perot腔和微球腔的基本原理,通过CO2激光熔融光纤实验制得了直径为1.2 mm的微球腔,并测试了微球腔和锥形光纤耦合结构的耦合特性.采用典型的PDH稳频系统设计了基于微球腔的稳频系统,分析了用于鉴频的误差曲线的吸收特性和色散特性,对比了不同调制频率、微球腔直径、耦合损耗、传输损耗下与误差曲线斜率的关系.结果表明:耦合状态下最大Q值可达到1.1×108,调节微球腔内横磁模和横电模的转换可优化耦合效率,匹配微球腔和锥形光纤的尺寸得到了径向二阶模式的透射谱,误差曲线效率达到15.4A mW/MHz.球腔在提高PDH稳频技术灵敏度上具有巨大潜力.     

Fiber taper coupled high-quality-factor planar microdisk

A fiber taper can evanescently couple to whispering gallery modes (WGMs) in a planar silica microdisk for observing the optical properties of the microdisk cavity. It is revealed that WGMs have very high quality (Q) factors by controlling the air gap between the taper and the microdisk. The best coupling efficiency from the taper to the microdisk is as high as 98%, and can be continuously adjusted from the under-coupling, critical-coupling to over-coupling regimes. The influence of the laboratory circumstance such as surface contamination on the microdisk is also discussed. It is experimentally shown that the high-Q-factor (105) modes can be kept for a long period in a general laboratory circumstance.     

光学微球腔的壳层结构研究

使用时域有限差分法，对带表面壳层的光学微球腔进行模拟计算，分析了微腔内回音壁模式的能量密度分布，总结了壳层厚度对微球腔谐振性能的影响，并由此探讨对微球腔进行调谐和模式控制的方法.采用这种壳层结构，微球腔的谐振性能得到了有效提高（Q值提高了30％以上，模式体积减小了60％），为光学微球腔后续的结构设计和实际应用提供了一个新的优化思路.     

A method to optimize the RF-field distribution in a gyromonotron

The maximum efficiency of a gyromonotron depends on the RF-field and the DC magnetic field distributions in the interaction region of the resonator. A method for optimizing the RF-field distribution is presented by using a ballistic approach. A section of a sin² electric field distribution is found to be suitable.     

Spontaneous emission of an atom in a cavity with nonorthogonal eigenmodes

The spontaneous emission of an excited atom in a lossy cavity with nonorthogonal eigenmodes is analyzed. The quantum Langevin formalism is used to describe the dynamics of the spontaneous decay. The analysis shows that the spontaneous decay is modified by the Q value and the effective mode volume factor of each cavity eigenmode. The effective mode volume is generalized for cavities with nonorthogonal modes, which can be a very significant modification in the microcavity regime. It is shown that the spontaneous decay is not enhanced by the excess noise factor as claimed by other analyses.     

Investigation of flow features and acoustic radiation of a round cavity

In this work, the interaction between a boundary layer and a circular cylindrical cavity is studied. Experimental pressure and velocity results for a cavity of diameter 10 cm and depth ranging from 10 to 15 cm are described, for flow velocities between 50 and 110 m s^?1. This flow configuration is found to generate intense discrete depth- and flow-dependent tones, resulting in modes similar in appearance to Rossiter modes found in shallow rectangular cavities. Differences between the cylindrical cavity's mean flow and that of a similarly sized rectangular cavity are highlighted. The development of the shear layer is quantified, in terms of thickening and of velocity statistics profiles. Radial and azimuthal acoustic modes are observed in the acoustic field inside the cavity. A feedback model based on the coupled behaviour of the fundamental acoustic depth mode of the cavity and the large scale dynamics of the shear layer is constructed, and its response is compared to experimental data. A good qualitative agreement between available data and modeled behaviour is observed, allowing the two acoustic modes found in this work to be attributed to the interaction of the shear layer with the cavity's fundamental depth mode.     

Coaxial resonator for a megawatt 280 GHz gyrotron

To provide the required mode selectivity for a megawatt 280 GHz gyrotron, a coaxial resonator operating in a high order TE mode is considered. Mode discrimination is achieved both by exploring the differences in the transverse structures of the competing modes and investigating a suitable geometry for the coaxial insert. For modes with close eigenfrequencies the associated diffractionQ factors can be widely different in value, thereby ensuring an effective mode selection. In the resonator studied here, the frequency separation between the design mode TE_26,10,1 and its nearest competing mode TE_20,12,1 is about 0.6% and the ratio of the correspondingQ factors is as high as 6.5. Unlike the coaxial resonator, in the hollow cavity without the inner conductor the fundamental spectrum of eigenfrequencies is more dense, and all TE modes within the frequency interval 271–288 GHz have approximately the sameQ factor.     

太赫兹波导滤波器的分析与设计

分析了不同宽边情况下对滤波器加工精度的影响,分析结果表明对于不同频段的滤波器,需要选择合适的谐振腔的宽边才能达到较好的性能,同时分析了不同谐振模式的滤波器对加工精度的影响,分析表明,对于太赫兹频段滤波器,选用TE101谐振模式时存在腔体长度会比波导的宽边小很多的情况,而选用高阶谐振模式不但可以提高滤波器的品质因数Q值,减少损耗,同时也能在一定程度上降低滤波器对加工精度的要求。最后以0.34 THz 4阶带通滤波器为例验证此方法的正确性,测试表明该滤波器最低损耗为-0.73 dB,在0.335~0.349 THz范围内损耗在-2 dB以内。     

Studies on high order mode of bell-shaped prototype cavities

Aluminium and copper prototype cavities were designed to study higher order modes(HOM).An automatic field mapping system was developed with LabVIEW to measure the adiofrequency(RF)charac teristics,such as resonant frequency,Q-value,shunt impedance and electromagnetic field distribution of the higher-order modes in a model RF cavity.Two kinds of the bell-shaped cavities were measured using the field mapping system,their frequencies are 1.5 GHz and 800 MHz respectively.The fields' distributions of the monopole modes and dipole modes,as well the R/Q values,were measured.     

两等同双能级原子与q模腔场任意N∑光子共振相互作用辐射谱研究

本文建立了“q模腔场-两原子”系统的任意N^∑光子相互作用模型,利用这一模型研究了两个偶极一偶极力关联的等同双能级原子与q模腔场任意N^∑光子.共振相互作用的辐射谱.对q模腔场分别处于不同数态:即q模腔场均为真空场、q模腔场均为强场、1模为真空场(q-1)模为强场、q₀模为真空场(qq₀)模为强场、以及(q-1)模为真空场1模为强场时辐射谱的结构持征及物理特性进行了详细分析,揭示出“q模腔场-两原子”系统任意N^∑光子共振相互作用辐射谱的一般特征.现有文献报道,仅仅是本文的普遍性结果在各种不同情况下的特例.     

Bragg-induced orbital angular-momentum mixing in paraxial high-finesse cavities

Numerical calculation of vector electromagnetic modes of plano-concave microcavities reveals that the polarization-dependent reflectivity of a flat Bragg mirror can lead to unexpected cavity field distribution for nominally paraxial modes. Even in a rotationally symmetric resonator, certain pairs of orbital angular momenta are necessarily mixed in an excitation-independent way to form doublets. A characteristic mixing angle is identified, which even in the paraxial limit can be designed to have large values. This correction to Gaussian theory is of zeroth order in deviations from paraxiality. We discuss the resultant nonuniform polarization fields. Observation will require small cavities with sufficiently high Q. Possible applications are proposed.     

Positioning photonic crystal cavities to single InAs quantum dots

We have investigated the optical properties of planar photonic crystal cavities formed by removing a single hole from a two-dimensional square lattice of air holes etched through a thin GaAs slab. We have demonstrated cavity resonances with quality factors (Q’s) as high as 8500, using an internal light source provided by an ensemble of InAs quantum dots (QDs) grown by molecular beam epitaxy (MBE). The high-Q modes are confined to a very small mode volume, V = 0.7(λ/n)³, making them attractive to study in the context of cavity quantum electrodynamics with single QDs, where a high is needed to observe the strong coupling between an electronic state of the dot and the optical cavity mode. To this end, we have developed an accurate and robust alignment technique that positions a photonic crystal cavity to a single QD with 25 nm resolution. We present the details of this new technology and demonstrate its effectiveness by strategically positioning a number of QDs within photonic crystal cavities at points where the electric field intensity is high.     

Non-tilting out-of-plane mode high-<Emphasis Type="Italic">Q</Emphasis> mechanical silicon oscillator as a moving cavity mirror

A very sensitive optomechanical sensor to detect femtometer-level displacements in the position of one of the cavity mirrors in a Fabry–Pérot interferometer was constructed and characterized. We use a high-reflectivity coated, non-tilting out-of-plane mode high-Q mechanical silicon oscillator as a rear mirror in the Fabry–Pérot interferometer. The benefit of our novel oscillator, if compared to traditional torsional, flexural and many bulk acoustic mode oscillators, is that the action of weak forces is observed to cause only pure linear translation of the moving mirror without any tilting or deformation of the mirror surface. This non-tilting behavior allows, in principle, more precise optical mode stabilization, use of very short optical cavities and studies of short-range interactions between parallel surfaces. The resonance frequency and Q value of the high-reflectivity coated silicon oscillator are f₀=27.5 kHz and Q=19000 at low pressure (p=0.1 mbar) and at room temperature. The finesse of the optical cavity is . The sensitivity of the displacement measurement is Δx_min=5 fm with a 1 Hz bandwidth. The prospects of reaching the standard quantum limit in an interferometric displacement measurement using a macroscopic oscillator are discussed. PACS 78.70.-g; 07.10.Cm; 07.60.Ly     

Ku波段径向线相对论速调管放大器的仿真与设计

高频段相对论速调管放大器(RKA)是近年来高功率微波领域的研究热点之一,其发展主要受限于模式竞争、相位抖动和效率偏低等问题。设计了一种径向线RKA,主要由输入腔、两组非均匀双间隙群聚腔和三间隙提取腔等四部分构成。通过比较单双间隙群聚腔与电子束互作用的耦合系数,说明了非均匀双间隙群聚腔具备对电子束较强的调制能力。前端加载TEM模式反射器的非均匀双间隙群聚腔的工作在TM01-π模式,Q值较大,有利于谐振腔之间的能量隔离。采用两组非均匀双间隙群聚腔级联的方式,在注入功率仅10 kW情况下,实现短漂移管长度下电子束深度群聚达110%。粒子模拟结果表明,该器件具有效率高的优点,在电子束电压400 kV,电流5 kA,磁场强度0.4 T条件下,得到功率825 MW,频率14.25 GHz,效率41%的微波输出。     

Symmetric bifurcations and phenomena of polarization symmetry breaking in a single-mode gas laser

An analysis is carried out of the optical cavities whose natural modes have the form of Gaussian beams with complex astigmatism. In the case of coincident eigenvalues of the cavity ray matrix, the wave beams were found to be determined not only by the geometrical optics characteristics of a cavity, but also by additional cavity-independent parameters. A detailed analysis is given for the fundamental mode of such cavities. Concrete cavities possessing these properties are noted.