High-power superfluorescent source with a side-pumped Yb-doped double-cladding fiber

A compact supe uorescent source based on an Yb-doped double-cladding fiber amplifier is described. The packaged amplifier is pumped at 975 nm by side-coupling emission from a 2.0-W broad-stripe laser diode through an imbedded V groove. The fiber source generates 485 mW of broadband emission centered at 1055 nm with a 41-nm FWHM flat power spectrum.     

Polarization-maintaining amplifier employing double-clad bow-tie fiber

We report a polarization-maintaining double-clad Yb-doped fiber amplifier employing bow-tie fiber. Borosilicate stress elements were incorporated into the inner cladding of the fiber, yielding a beat length of 5.1 mm at 633 nm. When the fiber was pumped at 975 nm and seeded with linearly polarized light, the polarization extinction ratio was >15 dB , independent of pump power, and the output power was as high as 3.5 W.     

光纤放大器放大自发辐射特性与高温易损点位置

在高功率光纤放大器实验中,时常发现增益光纤抽运注入熔接点后10—50 cm处容易发生光纤烧毁现象.为了对该现象进行理论预测,基于光纤激光器速率方程模型和增益光纤的热传导模型,从种子功率、抽运功率和抽运吸收三个方面对掺镱双包层光纤放大器中的放大自发辐射(ASE)和温度特性进行研究.结果表明,在放大倍率较高、ASE较为严重等情况下,光纤放大器中的最高温度点一般不在抽运注入的熔接点处,而在距离熔接点10—50 cm处,与实验中发现光纤烧毁的位置基本符合.从光纤放大器的ASE抑制、最高温度点温度控制角度出发,对光纤放大器在种子功率、抽运功率、抽运吸收、放大倍率和抽运波长等方面的设计给出了指导性的建议.     

Highly efficient 4-W Yb-doped fiber amplifier pumped by a broad-stripe laser diode

A Yb-doped double-cladding fiber amplifier is v-groove side pumped by a 100-mum -wide, broad-stripe, 975-nm laser diode. The amplifier exhibits, separately, 39% electrical-to-optical conversion efficiency, 89% internal optical-to-optical conversion efficiency, 4-W output power at 1060 nm, and a small-signal gain of 53 dB.     

Narrowband bulk Bragg grating optical parametric oscillator

A narrowband, pulsed optical parametric oscillator (OPO) whose output coupler is a bulk glass Bragg grating is demonstrated. The OPO is based on periodically poled KTiOPO4 and is pumped by a pulsed, frequency-doubled Nd:YAG laser at 532 nm, generating a signal at 975 nm with a total efficiency of 35%. This novel and compact device shows a spectral bandwidth of 0.16 nm (50 GHz), a decrease by a factor of 20 compared with that when a conventional mirror is used. By using a folded cavity, we demonstrate tunable radiation with a tuning range of 60 nm and maintained spectral bandwidth.     

Hybrid glass substrates for waveguide device manufacture

Hybrid glass substrates were prepared by a novel, low-temperature process joining active (Er-Yb codoped) and passive phosphate glass. The resulting hybrid substrates are chemically and physically robust; they can be cut, ground, and polished by conventional, water-based techniques. The entire substrate can be immersed in a molten-salt bath to produce waveguides simultaneously in the active and passive regions. A low reflectance of -34+/-2 dB was measured at the joint interface with 1531.2-nm light by optical low-coherence reflectometry. Further, a hybrid laser waveguide device exhibited a slope efficiency of 33% at 1540 nm when pumped at 975 nm.     

High power diode-pumped triply doped fibre laser

A triply doped fibre laser is demonstrated for the first time. Using the 805 nm and 975 nm output from two diode laser sources to simultaneously pump a 2.1 m Yb³⁺, Tm³⁺, Ho³⁺-doped silica fibre laser, a maximum output power of 4.3 W was generated at slope efficiencies of 21% and 11% with respect to the launched 805 nm and 975 nm pump light, respectively. Whilst a number of energy transfer upconversion processes at the current dopant concentration levels appear to have impacted on the overall efficiency of the laser, the use of two separately pumped sensitiser ions to excite a single lasant ion has been shown to be a successful approach. PACS 42.55.Wd; 42.55.Xi; 42.60.Lh; 42.60.Pk     

Multi-wavelength mode-locked Er/Yb Co-doped fiber laser with square nano-second pulse output

We report a multi-wavelength mode-locked Er/Yb codoped fiber laser with square nano-second pulse output, which is constructed with a “figure-of-eight” cavity structure. A section of polarization-maintaining Er/Yb co-doped double clad fiber was used as the gain medium and pumped by a fiber pigtailed multimode laser diode working at 975 nm via a multimode fiber combiner. Several megahertz repetition rate output pulses with peak power up to 9.2 W and pulse duration around several nanoseconds were obtained.     

高功率光纤激光器二级抽运技术的理论分析

从理论上分析了高功率光纤激光器直接抽运和二级抽运的斜率效率和热管理问题. 计算结果表明:波长为975 nm的激光直接抽运产生波长为1070 nm的激光时,理论斜率效率为80%,但当抽运光功率为10 kW时,在强制水冷条件下纤芯极值温度也难以降到150 ℃以下;在二级抽运技术中,波长为1018 nm的激光抽运产生波长为1070 nm的激光时,若采用传统的包层抽运技术,其斜率效率不足20%,如果抽运功率填充因子由0.0025提高到0.1,则理论上斜率效率可由18.5%提高到80.9%,从而总斜率效率由15.5 关键词： 二级抽运 功率填充因子 斜率效率 热管理     

Nanocrystalline Sr2FeMoO6 prepared by citrate-gel method

Double perovskite Sr₂FeMoO₆ powders with small crystallite size have been synthesised with citrate-gel method. The starting solution pH was varied between 1.5 and 9.0 resulting in large differences in the phase composition and ordering of B^′/B^″ sites. The samples prepared at 975 °C had crystallite sizes under 40 nm whereas crystallite sizes of the samples prepared at 1050 °C were between 78 and 239 nm. The XRD patterns were refined with spacegroup I 4/m, which gave good results for both batches, although clearly better results were obtained with monoclinic P 2₁/n spacegroup for the 975 °C batch. The ordering and the saturation magnetization agreed well with each other after treatment at 1050 °C, but the samples prepared at 975 °C had a strongly reduced saturation magnetization from that given by the ordering.     

Power scaling potential of Yb:NGW in thin disk laser configuration

We report on efficient laser operation of Yb:NaGd(WO₄)₂ (Yb:NGW) in thin disk laser configuration. Using doping concentrations of 10.7 at. % and 15.3 at. % and disk thicknesses between 0.1 mm and 0.4 mm the optimum crystal parameters have been determined. A 0.1 mm thick, 10.7 at. % Yb:NGW disk pumped at 975 nm delivered 18.2 W of output power at 43.6 W of incident pump power with a slope efficiency of 51% and a resulting optical-to-optical efficiency of 42%. Using a 2 mm thick birefringent filter, continuous tuning from 997 nm to 1075 nm has been achieved. PACS 42.55.Rz; 42.60.Lh; 42.70.Hj     

一种基于增益调制技术的全光纤化脉冲Yb光纤激光器

以波长为975 nm的半导体激光器作为泵浦源,周期性地脉冲泵浦一个包含Yb掺杂光纤和光纤光栅对的Yb光纤激光器,实现了基于增益调制技术的全光纤化高功率Yb光纤激光器的稳定脉冲输出.在50 kHz重频下,采用20 W的泵浦功率和2.4 μs的泵浦脉冲宽度,获得了1 060 nm波长脉冲宽度仅100 ns的稳定脉冲激光输出,单脉冲激光能量约为20 μJ.以此作为脉冲激光种子进行功率放大,获得了性能稳定的全光纤结构高功率脉冲激光输出,放大后单脉冲能量超过200 μJ,激光放大器斜率效率达到60%.     

10-W-level diode-pumped compact 2.78 microm ZBLAN fiber laser

We report on >9W transverse-fundamental-mode CW output near 3 mum from a 4m heavily erbium-doped ZBLAN double-clad fiber laser pumped by a collimated 100 W 975 nm laser diode array. The pump threshold of the fiber laser was about 1W, and the slope efficiency was 21.3%. The peak wavelength of free running was about 2708 nm at low pump power and moved to around 2785 nm at high pump power. Output of 9W was obtained when the launched pump power was 42.8W. The output, however, fluctuated intensively like a pulsed laser, and the operation broke down with optical damage of the pumping end facet when the pump was increased beyond 42.8 W. Therefore, alleviation of the operation fluctuation, heat management, and strengthening the pumping fiber are crucial considerations for the stable operation of 10-W-level mid-IR ZBLAN fiber lasers.     

Watts-level, short all-fiber laser at 1.5 microm with a large core and diffraction-limited output via intracavity spatial-mode filtering

We report over 2 W of single spatial-mode output power at 1.5 microm from an 8-cm-long, large-core phosphate fiber laser. The fiber has a numerical aperture of approximately equal to 0.17 and a 25-microm-wide core, heavily doped with 1% Er(+3) and 8% Yb(+3). The laser utilizes a scalable evanescent-field-based pumping scheme and can be pumped by as many as eight individual multimode pigtailed diode laser sources at a wavelength of 975 nm. Nearly diffraction-limited laser output with a beam quality factor M2 approximately equal to 1.1 is achieved by use of a simple intracavity all-fiber spatial-mode filter. Both spectrally broadband and narrowband operation of the laser are demonstrated.     

A 0．98μm Laser Diode Pumped Erbium－Doped Fiber Amplifier with 40nm Bandwidth

Ａ０．９８μｍＬａｓｅｒＤｉｏｄｅＰｕｍｐｅｄＥｒｂｉｕｍ－ＤｏｐｅｄＦｉｂｅｒＡｍｐｌｉｆｉｅｒｗｉｔｈ４０ｎｍＢａｎｄｗｉｄｔｈ￥ＬＩＪｉｎｇｈｕｉ；ＰＥＮＧＪｉａｎｇｄｅ；ＪＩＡＮＧＸｉｎ；ＹＡＯＭｉｎｙｕ；ＷＵＧｅｎｇｓｈｅｎｇ；ＦＡＮＣｈｏ...     

掺镱硅酸盐玻璃的光谱性质

采用高温熔融工艺制备了掺Yb^3＋硅酸盐玻璃。测试了玻璃的吸收光谱和荧光光谱,计算并分析了Yb^3＋离子在975nm附近的吸收截面和积分吸收截面随掺杂浓度的变化趋势。玻璃光谱曲线表明：吸收主峰位于975nm,在900—960nm范围内有一个弥散的吸收峰,中心波长为930nm;荧光主峰位于975nm,荧光次峰位于1010nm。综合其性能表明实验中硅酸盐玻璃的最佳Yb^3＋掺杂浓度为4mol%。     

All-fiber erbium-doped dissipative soliton laser with multimode interference based on saturable-reserve saturable hybrid optical switch

Reverse saturable absorption is essential for the realization of dissipative solitons. In this paper, we introduce reverse saturable absorption by using nonlinear multimode interference (NL-MMI), for the first time, to the best of our knowledge, and obtain a stable dissipative soliton operation. By adjusting the coupling efficiency from multimode fiber to single mode fiber, the absorption properties of NL-MMI can be switched between saturation and reverse saturation. The dissipative soliton can be obtained with pulse width of 975 fs in the experiment, the 3-dB bandwidth at 1555 nm is 16 nm, and the maximum output power is 11.48 mW. The nonlinear absorption optical modulation and high damage threshold characteristics of the NL-MMI based ultrafast optical switch provide a new idea for realizing dissipative solitons.     

共掺Na+的Yb3+∶CaF2晶体的荧光分析与低阈值激光运转

基于975nm激发的室温下荧光光谱测量，系统地研究了在新型钠、镱共掺的氟化钙晶体中钠离子的作用机理，分析了掺钠离子浓度与激光阈值的关系，获得了具有最低激光阈值的掺杂浓度优化配比. 激光实验表明对于2%Yb³⁺离子浓度的氟化钙，掺入3%的钠离子能够获得最低阈值的激光运转，这与理论和荧光分析完全一致. 关键词： 镱、钠共掺氟化钙 荧光光谱 激光阈值     

Optical parametric amplifier pumped by two mutually incoherent laser beams

We report on the experimental proof-of-principle demonstration of the ultrashort pulse single-pass beta-barium borate, BBO optical parametric amplifier pumped by two mutually incoherent laser sources. We show that the amplified signal at 1054 nm gains energy from both pump pulses with wavelengths of 680 and 527 nm, respectively, with overall energy conversion of 36%, and exhibits low wavefront distortions and improved energy stability in the gain saturation regime. PACS 42.65.Yj; 42.65.Re     

Remote Temperature Sensor Based on the Up-Conversion Fluorescence Power Ratio of an Erbium-Doped Silica Fiber Pumped at 975 nm

Abstract

This article presents experimental results demonstrating the performance of an erbium-doped silica fiber as a remote temperature sensor in the interval from 20°C to 200°C. The sensor is based on the change in the fluorescence intensity ratio of two spectral bands as a function of temperature. The green fluorescence signal was generated by up-conversion processes in the erbium-doped fiber pumped at 975 nm. A radiometric analysis was applied to the erbium-doped fiber to evaluate its performance as a temperature sensor, and the results from this analysis were compared against other rare-earth-doped fiber sensors that utilize the intensity ratio technique.