High-power, single-mode, linearly polarized, ytterbium-doped fiber superfluorescent source

High-power operation of a single-mode, linearly polarized, broadband superfluorescent fiber source has been achieved by using a two-stage cladding-pumped fiber configuration comprising a low power, single-ended, ytterbium-doped superfluorescent fiber seed source and a high-power cladding-pumped, polarization-maintaining, large-mode-area, ytterbium-doped amplifier pumped by a high-power diode source at 976 nm. The source yielded a maximum linearly polarized output of 106 W with a slope efficiency of up to 67% with respect to the launched pump power and with a measured polarization extinction ratio of 13.5 dB. The wavelength spectrum of the superfluorescent source spanned the range continuously from ~1035 to 1100 nm, and the bandwidth (FWHM) of the emission spectrum was 21 nm. The minimum seed power required for an output power over 100 W was only 10 mW, corresponding to an effective power gain in the amplifier stage of 40 dB. Single-spatial-mode operation with a beam propagation factor (M(2))<1.1 was achieved by bending the amplifier fiber to a bend radius of ~8 cm, without a significant reduction in output power.     

Ultra-broadband amplified spontaneous emission source by using heterogeneous optical amplifier

In this work, we propose and experimentally investigate an ultra-broadband amplified spontaneous emission (ASE) light source with 113.8 nm bandwidth (1446.2 to 1560.0 nm) by using a cascaded two-stage optical amplifier, which is consisted of semiconductor optical amplifier (SOA, 1st stage) and erbiumdoped fiber amplifier (EDFA, 2nd stage), when the output intensity is above ?35 dBm/0.01 nm. And, the EDFA only uses a 3 m long erbium-doped fiber (EDF) with a 27 mW pumping power and SOA is driven at 200 mA bias current. Moreover, the proposed amplifier also can provide a broadband gain amplification of 114 nm in the wavelengths of 1464.0 and 1578.0 nm with the noise figure distribution of 6.8 to 8.1 dB.     

同带抽运高效率光纤放大器

以光纤光栅为谐振腔搭建了波长为1020 nm的光纤激光器,并通过两级级联放大获得了590 mW的最大输出功率. 利用获得的波长为1020 nm的激光进行了波长为1064 nm种子光同带抽运放大,实验研究了不同增益光纤长度时放大器的输出功率和转换效率. 当增益光纤长度为8.5 m时,放大器最大输出功率为385 mW,斜率效率为81%. 进行了波长为976 nm的半导体激光器直接抽运波长为1064 nm种子光的实验. 在增益光纤长度最优时,其斜率效率为56.4%. 实验结果表明,同带抽运方式比传统抽运方式具有更高的转换效率. 研究结果可为波长为1020 nm的激光高功率放大和波长为1064 nm的光纤激光高功率同带抽运放大提供一定的参考. 关键词： 同带抽运 光纤放大器 斜率效率     

90.4-W all-fiber single-frequency polarization-maintained 1083-nm MOPA laser employing ring-cavity single-frequency seed oscillator

A high-power all-fiber single-frequency polarization-maintained（PM）laser operating at 1 083 nm is demonstrated using a master oscillator power amplifier（MOPA）structure.The seed source of this MOPA laser system is an in-house-built ring-cavity fiber oscillator.Four-stage amplification configuration is employed, in which the maximal output power of the main amplifier is 90.4 W,corresponding to a conversion efficiency of 72.5%.The polarization extinction ratio of the output light is 13 dB.The amplified spontaneous emission is suppressed by a factor of over 25 dB,and no stimulated Brillouin scattering effect is observed when a large-mode-area and high absorption coefficient PM gain fiber is employed.     

高功率、低量子亏损同带抽运掺镱光纤放大器

开展了基于同带抽运的高功率、低量子亏损的掺镱光纤放大器实验研究. 搭建了一台输出功率为21 W的1018 nm短波 长掺镱光纤激光器, 并利用其对双包层掺镱光纤进行同带抽运, 获得18.6 W的1080 nm波段激光输出, 光-光转换效率高达90.86%. 关键词： 光纤放大器 同带抽运 双包层光纤 转换效率     

High-power tunable single-frequency single-mode erbium:ytterbium codoped large-core fiber master-oscillator power amplifier source

We present a cladding-pumped single-frequency, single-mode erbium:ytterbium codoped fiber master-oscillator power amplifier source generating up to 151 W of continuous-wave output power at 1563 nm with 33% slope efficiency and 20 dB gain. This source was also tunable and had a stable operation range of 1546 to 1566 nm at an output power level in excess of 125 W. The doped fiber exploited a large-core design for improved power handling and mitigation of stimulated Brillouin scattering. There was no sign of having stimulated Brillouin scattering even at the highest power. Despite a large core (V = 12), the output beam was nearly diffraction limited (M2 = 1.1). The source showed slight rollover at over 100 W of output power because of the onset of emission from ytterbium, centered at 1060 nm.     

2μm single-frequency master-oscillator fiber power amplifier

We report a single frequency laser source consisting of a Tm:YAP coupled-cavity master-oscillator and a Tm-doped fiber power amplifier. The MOFPA yielded 4.55 W of single frequency output at 1990 nm when the input signal was 270 mW and the pumping power was 35.2 W. A strong amplification of spontaneous emission (ASE) was observed when higher pumping power was applied. Therefore, the output power of the single frequency fiber power amplifier was limited by the input power of seed laser.     

基于光纤拉曼放大的级联式全光纤1020nm光源

设计并制作了输出功率为196 mW的级联式全光纤1020 nm光源.该光源采用光纤拉曼放大器与掺镜光纤放大器级联的放大方案,实现了对低功率1020 nm种子光的放大.在光纤拉曼放大级,采用了3段不同长度的拉曼增益光纤进行了对比实验,比较了一定信号光功率和抽运光功率下拉曼增益光纤长度对光纤拉曼放大级输出功率的影响;测量了...     

Dual-core ytterbium fiber amplifier for high-power 1060 nm swept source multichannel optical coherence tomography imaging

A novel (to our knowledge) dual-core ytterbium (Yb(3+)) doped fiber, as an optically pumped amplifier, boosts the output power from a 1060 nm swept source laser beyond 250 mW, while providing a wavelength tuning range of 93 nm, for optical coherence tomography (OCT) imaging. The design of the dual-core Yb-doped fiber amplifier and its multiple wavelength optical pumping scheme to optimize output bandwidth are discussed. Use of the dual-core fiber amplifier showed no appreciable degradation to the coherence length of the seed laser. The signal intensity improvement of this amplifier is demonstrated on a multichannel in vivo OCT imaging system at 1060 nm.     

1410 nm波段分布式光纤拉曼增益放大器的研究

讨论了分布式光纤拉曼增益放大器的工作原理,采用1320nm固体激光器作为抽运源,获得了1410nm波段附近的光放大,在单模GI光纤长度为23km时,初步研究了拉曼放大器增益与光纤作用长度的关系,抽运脉冲峰值功率分别为50W、30W时,光纤的有效作用长度分别为15．5km和10.5km;研究了在不同的光纤有效作用长度时,拉曼放大器增益与抽运功率的关系;从光纤拉曼光谱图估算了光纤拉曼放大器的光谱宽度为50nm或250cm^-1。     

Distributed-feedback fiber laser with optical amplifier

A single-frequency all-fiber laser source operating at 1093 nm with an output power of more than 1 W is developed. A master oscillator-power amplifier configuration that comprises a distributed-feedback fiber laser and an ytterbium-doped fiber amplifier is implemented. Some aspects of the stimulated Brillouin scattering specific to active fiber are discussed.     

Narrow-linewidth ytterbium-doped fiber amplifier system with 45 nm tuning range and 133 W of output power

We report on a master-oscillator ytterbium-doped fiber amplifier system with up to 133 W of continuous-wave output power using a tunable narrow-linewidth external-cavity diode laser seed source. Stable tunable high-power operation was demonstrated from 1040 nm to 1085 nm with more than 12 dB suppression of amplified spontaneous emission.     

Er/Yb co-doped fiber amplifier with wavelength-tuned Yb-band ring resonator

Erbium-ytterbium co-doped fiber amplifier with wavelength-tuned Yb-band loop resonator is presented. The amplified spontaneous emission (ASE) from Yb ions is utilized to stimulate a laser emission at several wavelengths from the 1 μm band in the 1550 nm amplifier. The wavelength of this lasing is tuned by introducing a fiber Bragg grating (FBG). The results show, that the overall efficiency of the amplifier at nominal 1550 nm wavelength can be increased by introducing a feedback loop with 1040 nm and 1050 nm FBG. This loop also protects the Er/Yb amplifier from parasitic lasing at 1 μm and allows significant output power scaling without risk of self-pulsing.     

Efficient special S-band ytterbium fiber laser emitting at 1012 nm and its application in tandem pumping

We presented the first demonstration of a special S-band Yb-doped fiber laser with a central wavelength of 1012 nm. By pumping common alumosilicate fiber doped with 974 nm laser diode, efficient lasing at 1012 nm was achieved with a maximal output power of 331 mW and 55% power conversion efficiency. We also built a fiber amplifier to validate the feasibility of the 1012 nm laser as the tandem pump source by boosting the 1064 nm C-band laser power up. The slope efficiency of the tandem-pumped fiber amplifier is 63%.     

Generation of 520 mW pulsed blue light by frequency doubling of an all-fiberized 978 nm Yb-doped fiber laser source

Pulsed blue light at 489 nm has been generated by second-harmonic-generation of a nanosecond pulsed master-oscillator power amplifier system based on a short Yb(3+) doped single-mode fiber amplifier at 978 nm and an external-cavity diode laser as seed source. The Yb(3+)-doped fiber was core-pumped by a W type Nd(3+) doped double-clad fiber laser operating on the transition near 930 nm ((4)F(3/2)→(4)I(9/2)). 520 mW of average power was generated at 489 nm using a periodically poled MgO:LiNbO(3), corresponding to a conversion efficiency of 34%.     

Passive erbium-doped fiber seed photon generator for high-power Er(3+)-doped fiber fluorescent sources with an 80-nm bandwidth

A novel structure that converts wasted backward amplified spontaneous emission (ASE) to seed photons for the amplifier stage is suggested for a high-power erbium-doped fiber (EDF) broadband source. A considerable increase in output power and bandwidth extension was achieved by placement of a segment of passive EDF in front of the amplifier stage, thus recycling backward ASE as the secondary pumping source for the passive EDF seed photon generator. Experimental results showed a dramatic increase in output ASE power of more than 10 dB for most radiation bands from 1540 to 1620 nm with the simple addition of an unpumped EDF segment to the ordinary fluorescence-source structure.     

Output power improvement in an Yb-doped fiber laser with an additional unpumped Yb-doped fiber

Master oscillator power amplifier (MOPA) technology has been widely used in high-power or ultrashort-pulse fiber laser systems because the shape of the laser pulse can be easily adjusted. Usually, the first amplification stage of a 1064 nm fiber laser uses the core-pumped Yb-doped fiber amplifier (YDFA); however, the gain or output power is limited owing to the strong amplifier spontaneous emission (ASE) in the 1030 nm band. This paper presents the improved output power in an YDFA by inserting an additional unpumped Yb-doped fiber, which absorbs the lost backward ASE emitted from the pump end. We achieved an output power increase of more than 10% in a low-power signal, and the increase in output power decreased as the signal power increased. Moreover, the insertion of an additional unpumped Yb-doped fiber restricted the unwanted 1030 nm lasing in a low-power signal.     

Characterization of a high-power tapered semiconductor amplifier system

We have characterized a semiconductor amplifier laser system which provides up to 200 mW output after a single-mode optical fiber at 780 nm wavelength. The system is based on a tapered semiconductor gain element, which amplifies the output of a narrow-linewidth diode laser. Gain and saturation are discussed as a function of operating temperature and injection current. The spectral properties of the amplifier are investigated with a grating spectrometer. Amplified spontaneous emission (ASE) causes a spectral background with a width of 4 nm FWHM. The ASE background was suppressed to below our detection limit by a proper choice of operating current and temperature and by sending the light through a single-mode optical fiber. The final ASE spectral density was less than 0.1 nW/MHz, i.e. less than 0.2% of the optical power. Related to an optical transition linewidth of Γ/2π=6 MHz for rubidium, this gives a background suppression of better than -82 dB. An indication of the beam quality is provided by the fiber coupling efficiency of up to 59%. The application of the amplifier system as a laser source for atom-optical experiments is discussed. Received: 8 May 2000 / Revised version: 21 September 2000 / Published online: 7 February 2001     

窄线宽光纤激光器在1030 nm波段实现3 kW近衍射极限输出

基于大模场面积掺镱光纤搭建了全光纤1030 nm高功率窄线宽光纤激光主振荡功率放大系统,实现了3004 W的最高功率输出,斜率效率69.27%,是目前报道的输出功率最高的1030 nm波段近衍射极限光纤激光器。最高输出功率时,x,y方向的光束质量因子分别为1.169,1.174,3 dB光谱宽度为0.18 nm,放大自发辐射抑制比达到37 dB。     

Multi-wavelength laser source based on enhanced four-wave-mixing effect in a highly nonlinear fiber

We propose a multi-wavelength laser source based on an enhanced four-wave-mixing (FWM) effect which is achieved when a highly nonlinear fiber (HNLF) and an Erbium-doped fiber amplifier (EDFA) are employed in a fiber loop. A multi-wavelength laser source with totally 28 new wavelengths and a wavelength spacing of 0.8 nm is demonstrated. The wavelength spacing of the proposed multi-wavelength laser source can be tuned from 0.1 to 5.0 nm, and output spectrum of the multi-wavelength laser source with the wavelength spacing of 0.4, 0.8, and 1.6 nm are presented.