Measurement of intrinsic Brillouin linewidth of fibers based on stimulated Brillouin scattering slow light

Intrinsic Brillouin linewidth is one of the essential parameters to optimize the gain spectrum of stimulated Brillouin scattering (SBS). A novel method for the measurement of the intrinsic Brillouin line-width based on SBS slow light is proposed and demonstrated. In this method, an implicit model based on the transient SBS theory is developed, and a data processing method is designed to obtain the value of the intrinsic Brillouin linewidth from the model. The measured results show that the method is effective for studying SBS slow light.     

On‐chip stimulated Brillouin Scattering for microwave signal processing and generation

Demonstration of continuously tunable delay, low‐noise lasers, dynamically controlled gratings, and optical phase shifting using the stimulated Brillouin scattering (SBS) process has lead to the emergence of SBS as a promising technology for microwave photonics. On‐chip realization of SBS enables photonic integration of microwave photonic signal processing and offers significantly enhanced performance and improved efficiency. On‐chip stimulated Brillouin scattering is reviewed in the context of slow‐light based tunable delay, low‐noise narrow linewidth lasers and filtering for integrated microwave photonics. A discussion on key material and device properties, necessary to enable on‐chip Brillouin scattering using both the single‐pass and resonator geometry, is presented along with an outlook for photonic integration of microwave signal processing and generation in other platforms.     

Stimulated Brillouin scattering slow-light-based fiber-optic temperature sensor

We propose and experimentally demonstrate a method for temperature sensing using stimulated Brillouin scattering (SBS)-based slow light. The approach relies on temperature dependence of the Brillouin frequency shift in a fiber, hence the time delay of an input probe pulse. By measuring the delay, temperature sensing can be realized. We achieve temperature measurement in a 100 m single-mode fiber (SMF) using a cw pump. The main temperature-sensing range is ～18°C from the room temperature, limited by the SBS gain bandwidth. To apply the technique for measurement of a shorter fiber segment, a pulsed pump is used to introduce SBS slow light. Temperature sensing is achieved in a 2 m SMF with a main sensing range of around ～25°C. The scheme is easily implemented, exhibits a relatively high temperature sensitivity with a resolution better than 1.0°C, and is potentially applicable for distributed sensing.     

Long Optical Delay Lines Enhanced by Ring Configuration in Optical Fibres

A long optically controlled delay line enhanced by ring configuration is demonstrated by using the group-velocity control of signal pulses based on stimulated Brillouin scattering. In experiment, two optical fibre ring cavities are used： one is used as the Brillouin laser, providing single-mode Stokes wave as probe wave; the other is used as the Brillouin amplifier, working as slow light medium. We achieve a maximum time delay of 215ns using the ring Brillouin amplifier, five times larger than the input probe pulse width of 40ns. In the meantime, a considerable pulse broadening is observed, which agrees well with the theoretical prediction based on linear theory.     

光纤中双宽带抽运SBS慢光及其脉冲展宽减小的理论研究

提出了一种单模光纤中采用双宽带抽运实现宽带受激布罩渊散射(SBS)慢光的方法.给出了双宽带抽运的SBS慢光及其脉冲展宽的理论模型.色散分析发现,两抽运光间存在一个最佳的频率间隔,可有效地减少由于群速度色散所引起的脉冲展宽.理论计算表明,该方案所获得的SBS增益带宽和信号脉冲群延迟分别提高到了相同条件下单宽带抽运的1.7倍和2倍.     

A new method for measuring the threshold of stimulated Brillouin scattering

A new method for measuring the threshold of stimulated Brillouin scattering (SBS) based on the generation location of a Stokes beam is proposed for the first time to our knowledge. The length of the medium cell is selected to be longer than the free gain length of pump pulses in the Brillouin medium. The reflected light from a certain mirror in front of the medium cell is chosen as the reference beam, and the SBS threshold is measured by the "jump" of the delay between the Stokes beam and the reference beam. An 8-ns Q-switched single-longitudinal-mode pulse is used as the pump and the typical SBS medium FC-72 is selected as the nonlinear medium in our experiment. The SBS threshold intensity is measured to be 173-178 mW/cm 2 , which is consistent with existing results measured with the transmitted energy limiting method.     

Numerical study on SBS slow light systems using a super-Gaussian filtered incoherent pump

We numerically investigate the performance improvement and its limitations using super-Gaussian filtered incoherent pumping in Stimulated Brillouin Scattering (SBS) slow light systems, especially for 2.5-Gb/s return-to-zero (RZ) OOK data streams. As compared to regular Gaussian filtering schemes, super-Gaussian filters can reduce the signal broadening without sacrificing the generated delay. On the other hand, although the figure-of-merits (FOM) in terms of the normalized delay and signal Q-factor products can be improved as well, additional sub-pulses may appear and subsequently the curve of FOM versus slow-light bandwidth exhibits a fluctuated behavior.     

受激布里渊散射介质CCl4中脉冲传输与功率限幅特性

分析了受激布里渊散射介质CCl4对纳秒激光脉冲的传输特性及功率限幅特性. 结果表明：透射脉冲波形随抽运光能量增加而压缩变形，脉冲前沿保持高斯型，后沿被压缩成功率“平台”，功率“平台”随抽运脉冲能量增加而逐渐变宽，但功率水平不变，表明该光学系统具有的功率限幅特性. 详细分析了功率限幅特性随抽运能量的变化规律和时间响应特性规律，采用脉宽为10ns、波长为1.06μm的Nd:YAG激光脉冲进行实验验证，理论与实验结论相符合.  关键词： 受激布里渊散射 功率限幅     

Waveform preservation of the backscattered stimulated Brillouin scattering wave by using a prepulse injection

We have found that it is possible to preserve the temporal waveform of the reflected wave generated from stimulated Brillouin scattering (SBS) by using a prepulse technique. The waveform of the SBS wave usually shows a steep rising edge in the ordinary SBS process. It has been found that the waveform of the reflected wave depends on both the prepulse energy and the time delay between the main pulse and the prepulses. A prepulse energy of 5 mJ and a time delay of 5 ns have been measured to be the optimum values under the experimental conditions. This prepulse method is useful in developing a multistage system employing several SBS cells in series for high-power laser applications.     

高非线性微结构光纤中基于受激布里渊散射的慢光延迟

全光连续可调的慢光技术在全光网络和光信息处理等领域具有重要的应用前景. 利用自行设计并拉制的高非线性微结构光纤, 实验研究了基于受激布里渊散射的可调谐慢光延迟. 采用单抽运光和单级延迟方案, 当抽运光功率为162.6 mW时, 在长度为120 m的高非线性微结构光纤中获得了最大76 ns的延迟量, 相当于0.76个脉冲宽度. 通过调节抽运光功率的大小, 可以实现对慢光延迟量的可调谐.该慢光延迟方案具有延迟量大、 全光可调谐及与现有光通信系统兼容等优势. 关键词： 慢光 微结构光纤 受激布里渊散射     

同轴正交偏振双脉冲序列受激布里渊散射抽运放大的实现方法

利用受激布里渊散射放大时抽运光与种子光可以有一时间延迟的特性,设计了一个同轴传播正交偏振双脉冲序列的偏振控制装置,使同轴传播的两个正交偏振脉冲光束在放大时具有相同的偏振态,从而实现了两束光的抽运放大.     

基于一种优化的梳状布里渊增益谱实现对任意周期信号的零展宽快慢光

在理论分析任意信号实现无畸变快慢光所需条件的基础上,根据周期信号的频谱特点,推导出一种优化的梳状布里渊增益谱的普适公式.利用该普适公式,可根据所需时间延迟或超前量,方便地得到周期信号每个离散频谱分量所对应的各离散布里渊增益谱的强度和增益谱峰值相对于频谱分量的偏移量,从而确定整个梳状布里渊增益谱的形状.通过对正弦信号、周期性高斯信号和周期性方波信号的数值计算,结果表明,利用该优化的梳状布里渊增益谱可实现这三种周期信号在零展宽下的快慢光,证实了所得普适公式的正确性.此外,通过调节各离散布里渊增益谱的强度和偏移量,时间延迟或超前量连续可调.     

光纤中基于双宽带抽运的受激布里渊散射增益谱展宽及慢光传输中脉冲失真减小的理论研究

分析了单模光纤中双宽带抽运的受激布里渊散射 （stimulated Brillouin scattering,SBS） 光速减慢效应.模拟了两高斯型宽带抽运光同时作用下的SBS增益谱和损耗谱,提出了一种获得均匀增益谱的方法.由于较强抽运光增益谱的中心频率与较弱抽运光损耗谱的中心频率相重合,通过调节较弱抽运光的功率和谱宽,能够部分地抵消掉较强增益谱的顶部从而构建出平坦的增益谱.研究了该平顶增益情形下信号脉冲畸变的性质.与单宽带抽运下脉冲畸变的对比表明,这种产生平顶增益谱的方法能有效地减小脉冲畸变. 关键词： 慢光 受激布里渊散射（SBS） 单模光纤 脉冲失真     

Effect of Brillouin slow light on distributed Brillouin fiber sensors

The effect of Brillouin slow light on distributed Brillouin fiber sensors (DBFSs) is studied. We demonstrate Brillouin slow light for a 1.2 ns pulse with peak powers (PS) from 3.3 to 56.2 mW on depletion of the pump power (PP) ranging from 1.3 to 83.2 mW in conventional optical fibers (SMF-28). Experiments show that, when pump power depletion is not negligible, for a given PP the Brillouin gain and delay time of a pulse decrease when PS increases in a long (> or =10 km) sensing fiber. The optimum pump beam depletion resulting from strong interaction of the pump and the probe in the fiber provides accurate temperature and strain information at a high spatial resolution. Our study reveals that at low PP the spatial resolution error caused by the pulse delay for a DBFS with centimeter spatial resolution is less than 5% of the pulse length.     

Cavity enhanced cw stimulated Brillouin scattering in a fused silica plate

We have observed cavity enhanced stimulated Brillouin scattering (SBS) in a high finesse optical ring resonator. Brillouin scattering occurs in a fused silica plate placed in the focus of the light beam inside the cavity. The frequency spacing of the Brillouin scattered wave relative to the incident beam at 23.5 GHz has a linewidth of less than 500 Hz. In preliminary experiments we extracted a scattered optical power of 25 mW from the resonator. Possible applications are discussed.     

矩形谱宽带光抽运的布里渊慢光中脉冲失真的分析

在小信号增益条件下推导出了高斯光脉冲经过矩形谱宽带光抽运的布里渊慢光系统后输出脉冲时域振幅包络的近似解析表达式,适用于抽运光频谱具有陡峭上升(下降)沿和平坦顶部的情况.定量分析和比较了光纤色散以及受激布里渊散射增益不均衡和增益所致色散效应对延迟信号光脉冲失真的影响.计算结果表明:当信号光脉冲的频谱处于布里渊有效增益谱内时,解析解与数值解符合,布里渊增益所致三阶色散效应是导致延迟信号光脉冲失真的主要物理因素,制约了窄脉冲延迟量的提高.     

Instability of Stimulated Brillouin Scattering in a Fiber Ring Resonator

We investigate theoretically the instability of transient stimulated Brillouin scattering (SBS) in a high- finesse fiber ring resonator consisting of a fiber ring and directional coupler. Unlike many reports to date, the linear phase detuning of the cavity is taken into account. It is found that SBS instabilities including the self-pulsing and chaotic behavior can occur even if the length of the fiber resonator is very short. SBS instabilities depend strongly on the linear phase detuning, the input power, and the coupling coefficient of the coupler.     

Stimulated Brillouin scattering phase conjugation of light beams carrying orbit angular momentum(Invited Paper)

We investigate the stimulated Brillouin scattering(SBS)properties of light beams carrying orbit angular momentum(OAM).The phase conjugation of light beams carrying OAM is experimentally achieved in an SBS mirror with a random phase plate.The spectrum and the pulse width compression of SBS light are measured.It is shown that the phenomena of pulse compression is observed and OAM conservation is confirmed in the SBS process.The OAM transfer from photons to phonons may find potential applications in photon-phonon conversion-based signal-processing schemes by using OAM multiplexing.     

18 W single-stage single-frequency acoustically tailored Raman fiber amplifier

A single-mode polarization-maintaining fiber doped to increase the Raman gain while suppressing stimulated Brillouin scattering (SBS) was utilized in a single-stage counter-pumped Raman fiber amplifier. The SBS suppression was achieved through the acoustic tailoring of the core. A pump probe experiment was conducted to characterize the Brillouin gain and indicated the existence of multiple Brillouin peaks. When the amplifier was seeded with approximately 15 mW of 1178 nm light, 11.5 W of cw output power was obtained with a linewidth ≤2 MHz. The application of a thermal gradient to further mitigate the SBS process increased the output power to 18 W, thus providing a net amplifier gain >30 dB.     

非线性光纤环镜在受激布里渊散射慢光级联系统中的可行性研究

基于非线性光纤环镜(NOLM)的脉冲压缩特性,分析了NOLM在基于受激布里渊散射(SBS)慢光级联系统中对延迟脉冲的影响.利用环形结构来模拟多次级联,有效地降低了系统的复杂度,得到了在不同抽运光功率和级联次数下脉冲的延迟输出特性.理论分析表明,NOLM可以有效地抑制SBS慢光级联系统中延迟脉冲的展宽,抽运光功率决定了展宽因子的变化趋势及最终稳定值的大小,展宽因子在级联4次时趋于稳定值,恰当选取抽运光功率可实现脉冲的零展宽延迟;改变抽运光功率和级联次数可以实现延迟量的连续可调,且延迟量理论上不受限制;增大抽 关键词： 慢光 脉冲压缩 非线性光纤环镜 受激布里渊散射