Tm3+掺杂的MFT玻璃蓝色荧光动力学

测量了Tm^3 掺杂的MFT玻璃材料的吸收光谱，J－O计算给出了该材料的光学跃迁强度参数Ωt(t=2,4,6)。测量了355nm激发下该材料的发射光谱，通过测量不同掺杂浓度Tm^3 的^1D2→^3H4和^1G4→^3H6荧光衰减曲线讨论了这两个能级寿命及荧光量子效随浓度的变化关系，计算当Tm^3 浓度的4％时引起^1D2和^1G4荧光猝灭的能量传递效率。指出了^1D2→^3H4的荧光猝灭属于电偶极－电偶极相互作用的能量传递所导致。     

掺铒铋酸盐玻璃光谱性质的组分依赖性研究

通过测试掺铒铋酸盐玻璃43Bi2O3-xB2O3-（57-x）SiO2（x=10，20，30，40，50mol％）中Er^3＋离子的吸收光谱、荧光光谱、荧光寿命及荧光强度，结合Judd—Ofelt和McCumber理论，对玻璃中Er^3＋离子光谱性质随玻璃组分的依赖关系进行了系统研究．研究结果显示，掺铒铋酸盐玻璃具有较其它玻璃优异的光谱性质．随着玻璃中组分B2O3含量的增加，强度参量Ω6、荧光半高宽和能级^4I15／2→^4I13/2间自发辐射跃迁几率相应增加，而荧光寿命、荧光强度和受激发射峰值截面相应减小，带宽品质因子（σe^pcak×FWHM）在组分B2O3含量30mol％时达到最大．     

掺铒铝硅酸盐玻璃光谱和上转换荧光性质研究

利用Judd小Ofelt(J—O)理论和吸收光谱计算了Er^3 、Yb^3 掺杂的铝硅酸盐玻璃的J—O参量、振子强度、跃迁几率、荧光寿命，量子效率以及上转换系数等参量，比较了饵离子^I13/2—^I15／2跃迁的光谱参量的计算与测量值，并讨论了玻璃中OH—浓度与荧光寿命、绿色上转换发光强度与抽运光功率的关系。     

Er玻璃近红外区上转换发光的研究

研究了Er,Yb共掺磷酸盐玻璃的上转换发光，对于在800nm附近的近红外发光进行了分析，认为该发光带是由于三种跃迁引起的，除了常见的4F9/2→^4I15/2跃迁以外，还存在着2H11/2→413/2,4S3/2→4I13/2的跃迁，还研究了Er^3 掺杂浓度对这三种跃迁的影响。     

硼碲酸盐玻璃材料中Er3+光谱性质对组分的依赖关系

采用熔融淬火技术制备了一组Er3+掺杂的变组分硼碲酸盐玻璃材料.测量了玻璃的折射率、吸收光谱及4I13/2→4I15/2跃迁的荧光寿命.利用标准的三参量Judd Ofelt理论对Er3+的光学跃迁性质进行了计算,并对Er3+离子的4I13/2能级的量子效率进行了研究.结果发现,随着样品中TeO2含量的增加样品的折射率变大,三个Judd Ofelt参量中Ω2随着样品组分的改变较明显,而另外两个参量Ω4和Ω6的变化较小.还发现随着TeO2含量的增加4I13/2→4I15/2辐射跃迁几率增大,并且该跃迁的量子效率增加.这一研究结果表明,在硼酸盐玻璃材料中引入TeO2可以有效地改善其中稀土离子的量子效率和辐射跃迁性能.     

铒离子浓度对掺Er3+碲酸盐玻璃的Judd-Ofelt理论参数的影响

制备了四种不同铒离子掺杂浓度的碲酸盐玻璃,通过测定吸收光谱计算了吸收谱线的振子强度,根据Judd-Ofelt理论计算了不同浓度下Er3 离子发光光谱的强度参数Ωi(i=2,4,6),计算了自发辐射电偶和磁偶跃迁概率、辐射寿命、荧光分支比等参数,讨论了Er3 离子浓度变化对以上这些参数的影响.测试了Er3 :4I13/2→4I15/2跃迁对应的荧光光谱和Er3 :4I13/2能级荧光寿命.最后应用McCumber理论计算了玻璃中Er3 :4I13/2→415/2跃迁对应的受激发射截面大小.结果表明:振子强度基本上随Er3 离子浓度的增大而增强;随着Er3 离子浓度的增加,自发辐射跃迁概率A基本呈现出递增的趋势,但荧光分支比β却只有很小的变化;Er3 :4I13/2→4I15/2的发射截面随Er3 离子浓度的增大而改变很小,有效线宽都在50 nm左右.     

Er3+/Yb3+共掺LiNbO3晶体中Er3+的光谱特性分析

在室温下,测量了采用Czochralski方法生长的as-grown和经退火处理的Z切Er^3＋／Yb^3＋共掺同成分LiNbO3晶体的α偏振吸收光谱（300-1650nm）。运用Judd—Ofelt理论对该晶体中Er^3＋的光谱特性进行了分析。由所测得的吸收系数的积分计算得到了从基态到激发态的若干个主要的电子跃迁强度实验值。利用最小二乘法确定出Er^3＋／Yb^3＋共掺LiNbO3晶体中Er^3＋的Judd-Ofelt参数。进而确定了自发辐射概率,从激发态能级到其各个下能级的荧光分支比以及能级辐射寿命。此外,还讨论了Yb^3＋的共掺和退火处理对LiNbO3晶体中Er^3＋光谱特性的影响。     

掺Er^3＋离子Sr3Y2（BO3）4晶体光谱性能的研究

研究了提拉法生长的掺Er^3＋的Sr3Y2（BO3）4晶体的吸收光谱和荧光光谱。应用J—O理论分析并计算了光谱参数,得到唯象参数Ω2、Ω4和Ω6分别为11．90×10^-20cm^2、3．44×10^-20cm^2和1．92×10^-20cm^2。在Er^3＋：Sr3Y2（BO3）4晶体中,Er^3＋在1533nm波长的发射截面为1．00×10^-20cm^2,^4I13／2→^I15／2能级跃迁的荧光寿命和辐射寿命分别为0．58ms和4．10ms,良好的光谱性能表明Er^3＋：Sr3Y2（BO3）4晶体可能成为潜在的1．55μm波段的一种激光材料。     

Cd3Al2SiO12玻璃中Er^3＋的光学跃迁

根据Judd-Ofelt理论,利用镉铝硅酸盐玻璃中Er^3 的吸收光谱,计算了实验与理论振子强度,用量小二乘法拟合实验与理论振子强度得到了三个J－O强度参数Ω2,Ω4,Ω6。并由此计算了Er^3 在不同能级之间的自发辐射系数A、辐射寿命τ、荧光分支比β以及积分发射截面∑。根据这些参数分析认为掺铒镉铝硅酸盐玻璃可能实现近红外激光输出。     

Er3+单掺和Er3+/Yb3+双掺铋硼酸盐玻璃的研究

用高温熔融法制备了Er^3 单掺和Er^3 /Yb^3 双掺铋硼酸盐玻璃样品，测量了上述玻璃样品的吸收光谱，荧光光谱，荧光寿命以及红外透过率。对高浓度掺杂Er^3 的铋硼酸盐玻璃中的浓度猝灭现象作出了解释。分析了Er^3 ／Yb^3 双掺铋硼酸盐玻璃样品中Yb^3 离子对Er^3 离子的敏化过程。研究发现Er^3 ／Yb^3 双掺铋硼酸盐玻璃在1．5～1．6μm波段有宽达81nm的荧光半峰全宽。实验还发现在熔制过程中通入氧气对其荧光寿命和红外透过率都有明显的提高。由于该玻璃材料表现出较好的物化性能。因此该材料可望成为宽带光纤放大器的适宜的基质材料。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.