全光纤调Q掺铒光纤激光器的脉冲研究

报道一种全光纤调Q掺铒光纤激光器,在其结构中采用带有光纤光栅的光纤环形镜作为调Q装置此调Q方案同时具有对腔内损耗进行调制和对激光输出波长选择的功能理论上分析了不同臂长差时的脉冲出现情况,与实验基本相符并对激光单脉冲产生及稳定性进行了分析讨论.     

980nm单模运转未镀增透膜光纤光栅激光器

提出了一种工艺简单的980nm未镀增透膜的光纤光栅外腔半导体激光器。首先从理论上分析了边模抑制比(SMSR)与激光二极管前表面反射率R2、外腔长Lext和激光二极管一光纤耦合效率之间的关系,得出边模抑制比随R2和Lext的增大而减小,而随着激光二极管一光纤的耦合效率的提高而增大。从计算结果中还可以看出,即使半导体激光器不镀增透膜(R2=0．3时)。在其它参量合适的情况下,边模抑制比仍可大于40dB。然后,对其进行实验验证。在半导体激光器未镀模的情况下,选择光纤光栅发射率为0．5,外腔长为12．5cm,输人电流为28．8mA(约为阈值电流的2．4倍)时,通过仔细调节恒温、恒流电路,实现了边模抑制比高于40dB的稳定的单纵模输出,外腔激光器的线宽优于1．6MHz。     

用时域ABCD矩阵对调Q锁模激光器的研究

用时域ABCD矩阵讨论了调Q锁模脉冲激光器输出脉冲的宽度和啁啾特性,主要给出了调Q元件作为幅度调制元件时的时域ABCD矩阵,并将光脉冲在激光腔中往返一周的ABCD矩阵写出,用此矩阵讨论了它对锁模脉冲的影响.给出了Nd:YAG激光器中用Cr⁴⁺:YAG作调Q元件时的调Q锁模脉冲激光器特性,并讨论了腔内色散、饱和吸收强度、增益带宽对输出脉冲特性的影响.用时域ABCD矩阵大大简化了计算过程.     

长周期光纤光栅中的包层模谐振

本文给出了光纤中包层模的电场形式,指出包层膜的电场形式与弱导光纤中导模的电场形式不同,对光纤中基模与包层模电场沿光纤横截面分布的重叠情况的分析表明,长周期光纤光栅除了能将HE₁₁导模耦合到HE_1p包层模外,也可以将其耦合到EH_1p包层模。基于耦合模理论的计算表明,耦合到EH_1p和EH_1,p-1包层模的耦合波长相近,对于典型的单模光纤,当p>4时耦合到这两个模式的耦合系数是可比的。     

掺Er光纤飞秒激光器中高信噪比载波包络位相偏移频率获取的实验研究

在实验上分析了掺Er光纤光学频率梳中激光器与一级放大器之间光纤长度、 光纤扰动以及放大器抽运功率对倍频程光谱和载波包络位相偏移频率(f₀)信噪比的影响. 通过系统优化, 实现了40 dB信噪比的f₀输出, 为f₀的长期锁定和光纤光学频率梳的实现提供了技术保障.     

Nd:LMA自锁模飞秒激光器腔结构最佳化设计

Nd:LMA晶体相对低的非线性折射率n₂,使得针对Ti:Sapphire自锁模激光器设计的腔,对Nd:LMA介质而言并没有提供足够的自幅度调制(SAM).为了在Nd:LMA激光器上实现自锁模,在腔内引入一个具有大的非线性系数n₂、快的响应时间的SF57介质,这样就使得激光腔的结构比较特殊.在这篇文章里利用ABCD传输矩阵对该激光器的结构从理论上进行了分析和计算,使腔结构达到了最佳化设计.     

强反馈光纤光栅外腔半导体激光器

在理论上对强外腔反馈情形的半导体激光器线宽压窄效应进行了分析，对消反膜剩余反射率，外腔反射率，外腔腔长对线宽压缩的影响进行了研究，在实验上采用光纤光栅作为反馈元件，与一端镀有消反膜的１．５μｍ波段的常规多纵模交导体激光器耦合，构成强反馈光纤光栅外腔半导体激光器，得到单频窄线宽的激光输出，静态下边模抑制比大于３０ｄＢ，线宽小于１２０ｋＨｚ。     

钛宝石激光再生放大器的研究

最近,我们采用上海光机所生产的(5.2×5.5×10)mm 的钛宝石激光晶体作为再生放大器的激光介质,实现了钛宝石激光再生放大器的运转.获得了1.2mJ 的能量输出.再生放大器的泵浦源是调 Q 的倍频 Nd:YAG 激光器,它的输出光脉冲宽度小于10ns,脉冲重复频率为10Hz,实验中为避免损伤晶体,采用的泵浦能量为50mJ.种子脉冲来自于自锁模钛宝石激光器,种子脉冲首先经过光栅展宽后再注入到再生脉冲,然后进行放大.注入的种子脉冲能量为1nJ,再生腔为平凹腔,R 为4m,腔长为1.65m.再生放大器的实验结果如图所示.     

铯原子调制转移光谱在激光稳频中的应用

利用铯原子D₂线的调制转移光谱的鉴频特性,实现了光栅外腔式主振荡器-功率放大型(MOPA)半导体激光器相对于铯原子6²S_1/2F=4→6²P_3/2 F’=5超精细跃迁的偏频锁定,在100 ms内激光频率的相对起伏小于±280 kHz.相对于一般的饱和吸收锁频方法而言,调制转移光谱在锁频中的应用不仅彻底消除了Doppler背景对锁频的影响,而且还避免了对激光器直接进行频率扰动而带来的附加频率噪音.     

基于级联光纤光栅的双模外腔半导体激光器的实验研究

实现了使用两个级联的光纤Bragg光栅的外腔半导体激光器的双模运转.两个模的峰值波长取决于光纤Bragg光栅的峰值反射波长,分别为1531.5nm与1549.4nm.注入电流为53mA时,两模峰值功率达到均衡为0.5mW,边模抑制比为27dB.     

短腔Er/Yb光纤光栅激光器

报道采用光敏Ｅｒ／Ｙｂ 光纤制作短腔Ｅｒ／Ｙｂ 光纤光栅激光器的实验结果。激光谐振腔由一对直接写在３０ ｍ ｍ 长的Ｅｒ／Ｙｂ 光纤上、长度分别为６ ｍ ｍ 及１０ ｍ ｍ 、反射率分别为９０％ 及９８．６％ 、３ ｄＢ带宽分别为０．２８ ｎｍ 及０．２６ ｎｍ 的光纤布拉格光栅组成, 激光器的泵浦阈值为８ｍ Ｗ, 斜效率约１４％ , 输出光的信噪比为６１ ｄＢ, 偏振模抑制比为３０ ｄＢ。     

Influences of geometry parameter on mode suppression ratio of fiber grating external cavity semiconductor laser

According to equivalent external cavity approximation model, after taking into account the joint contribution of semiconductor laser, external cavity and fiber grating (FG) to the phase condition, the mode distribution of the fiber grating external cavity semiconductor laser (FGESL) can be determined. As a result, the effect of the FG external cavity length (L) on the side mode suppression ratio (SMSR) of the FGESL is investigated theoretically. The results show that with the injected current and the coupling efficiency increase of the SMSR has taken on rise at all. For strong feedback (R₂ = 10^?4), the SMSR become more flattened with more than 40 dB, but, for weak feedback condition, The SMSR have lesser than 35 dB by an oscillation during rising course. Under the condition of short external cavity, the SMSR is in deep relation to the external cavity length, but the SMSR of longer external cavity is smaller than the SMSR of shorter external cavity on the whole and for 8–11 mm of the external cavity length, the SMSR of the FGESL has better (SMSR > 40.8 dB), and the SMSR become more flattened.     

光纤光栅外腔半导体激光器的高频调制特性

报道了光纤光栅外腔激光器瞬态特性的理论分析,引入了一个适用于外腔情况的等效光子寿命,模拟计算表明,要获得高于2．5GHz的调制速率,光纤光栅外腔的长度必须短于4cm范围,对所研制的光纤光栅外腔激光器进行了高频调制测量,得到了在1GHz下的单模激光输出,边模抑制比在40dB以上,3dB动态线宽为0．1nm左右,20dB动态线宽为0．3nm。     

弱耦合光纤光栅外腔半导体激光器

报道作者对单频窄宽光纤光栅外腔半导体激光器的一些研究结果。理论上分析了外腔的引入对激光器的阈值增益和光谱线宽的影响，实验上用自行研制的光纤布拉格反射滤波器（ＦＢＲ）与普通多纵模半导体激光耦合，在１．５５μｍ波段，得到边模抑制比大于２５ｄＢ，线宽小于６０ｋＨｚ的激光输出。     

Single-longitudinal-mode fiber laser with a passive multiple-ring cavity and its application for video transmission

A single-longitudinal-mode erbium-doped fiber laser with a passive multiple-ring cavity (MRC) is proposed for the first time to the authors' knowledge. The laser is fundamentally structured by insertion of three different short ring cavities, which serve as mode filters, into the main cavity. When it is combined with a mode-restricting intracavity fiber Bragg grating, the MRC resonator ensures single-longitundinal-mode laser oscillation. The laser can successfully suppress side-mode frequencies of as much as 1 GHz and provide an output power of 23 mW with a side-mode suppression ratio of 51 dB at 1533 nm. The short-term linewidth of the laser output measured is ~2 kHz . The ability of this fiber laser to act as an AM transmitter source is also demonstrated.     

Stable dual-wavelength erbium-doped fiber ring laser with switchable spacing employing controllable channel loss

A stable dual-wavelength erbium-doped fiber ring laser with switchable spacing is proposed and experimentally demonstrated. An arrayed waveguide grating (AWG) incorporating two fiber optic switches (OS) is used to as the wavelength selector. The ring cavity is divided into two cavities by a 30:70 optical coupler. Equalized dual-wavelength outputs are achieved by controlling the variable optical attenuator (VOA) inserted in the lower loss cavity. The wavelength spacing can be tuned from 0.80 to 12.05 nm. The fiber laser has good optical quality with maximum power fluctuation of 1.5 dB and side mode suppression ratios (SMSRs) higher than 71 dB.     

基于光纤光栅的磁场测量新方法

提出了一种基于光纤光栅中法拉第效应和测量偏振相关损耗的直接测量磁场的新方法,给出了理论分析和实验结果.当有外加磁场时,光纤光栅中的法拉第效应使两个圆偏振光的传播常量改变,从而导致光纤光栅的偏振相关损耗的变化.仿真结果表明,外加磁场与偏振相关损耗峰值在一定的测量范围内存在线性关系,测量结果对温度变化不敏感.分析了光栅的参量对测量性能的影响.实验中得到该方案测量磁场的灵敏度为7.8e-6B/Gs,利用现有精度为10-6 dB的光矢量分析仪得到最小可测磁场为2 Gs.实验与理论吻合较好.     

Wavelength stabilization of a 980-nm semiconductor laser module stabilized with high-power uncooled dual FBG

An optimized dual fiber Bragg grating (FBG) is proposed for 980-nm semiconductor lasers without thermoelectric coolers to restrict temperature-induced wavelength shift.The mathematical model of the temperature-induced wavelength shift of the laser with the dual FBG is built using the external cavity feedback rate equations.The external cavity parameters are optimized for achieving the stability mode-locking laser output.The spectral characteristics of the dual FBG stabilized laser are measured to range from 0 to 70 °C.The side mode suppression ratio (SMSR) is more than 45 dB,while the full-width at half-maximum (FWHM) is less than 1 nm.The peak wavelength shift is less than 0.1 nm.The dual FBG wavelength shift proportional coefficient is between 0.1086 and 0.4342.     

基于光纤光栅外腔激光器的全光波长转换器的阈值转换特性

使用半导体激活介质的增益饱和效应,描述了激光器型全光波长转换器波长转换机制及其阈值转换特性.实验研究了基于光纤光栅外腔半导体激光器的全光波长转换器的阈值转换特性,结果表明以此器件作为波长转换器可以将信号的消光比由5dB提高到30dB,并可将信号的强度起伏抑制到0dB,可实现部分信号数字再生功能.