GNSS测姿系统天线设置及精度分析

GNSS测姿系统的天线设置是影响测姿精度的重要因素之一;针对GNSS天线设置对测姿精度的影响问题,在分析GNSS测姿算法的基础上,对天线设置的3个决定因素,即天线数量、基线夹角和基线长度与姿态角误差的关系进行了理论推导,仿真分析了三者对测姿误差的影响程度;理论推导结果表明,对航向角、俯仰角和横滚角的测量至少需要三个固定天线,天线构成的固定基线相互垂直时姿态角的误差较小,姿态角的误差与基线长度的平方成反比;仿真结果验证了上述结论并进一步表明,两基线长度分别为1 m、2 m、3 m时,航向角和俯仰角的误差分别在2°、1°、0.5°以内,横滚角的误差分别在3°、2°、1°以内。     

三维空间中的偏振光导航方法

提出了偏振光/GPS/SINS组合导航方法。推导了偏振光辅助测姿原理并进行了仿真验证。提出了多模块改善能观度的方法。采用联邦卡尔曼滤波方法实现了组合导航算法,利用Matlab仿真方式分别对使用单偏振光模块和多偏振光模块的组合导航系统的测姿修正效果和能观度改善效果进行了检验。结果表明偏振光辅助测姿方法的引入能够大大改善导航系统的能观度和精度,非平行观测的多偏振光模块可以进一步提高系统性能。     

基于激光多普勒测速仪的车载组合导航

 针对车载纯捷联惯性导航系统(SINS)导航精度随时间增长而降低的不足,提出了基于激光多普勒测速仪（LDV）这一新型速度传感器的组合导航方案。通过建立SINS/LDV组合导航系统的状态方程和量测方程,设计了系统的卡尔曼滤波器,并对组合导航系统进行了仿真模拟。结果表明：SINS/LDV组合方案能够有效减小SINS导航参数随时间的累积误差,可以实现全自主、高精度导航;当LDV测速精度为0.1%时,组合导航系统的位置精度提高了2个数量级,速度精度提高了1个数量级。     

AR模型辅助SINS／GPS组合导航的实验研究

激光陀螺的随机漂移噪声类似于白噪声,可以采用AR（2）模型进行数字滤波来减小其对激光陀螺精度的影响。首先介绍了AR模型,然后利用IMU单元三组陀螺信号的AR（2）模型给出了车载SINS／GPS组合导航系统误差模型,并在GPS的辅助下,对SINS／GPS组合导航进行了实验研究。最后利用Kalman滤波器对车载SINs／GPS组合导航实际测量数据进行了离线的半实物仿真。实验结果表明,采用AR（2）模型辅助的SINS／GPS组合导航系统能够得到较高的姿态精度,并能有效抑制速度误差的发散。     

基于光纤陀螺捷联惯导的载体位姿精密测量

针对大型特种载体位姿测量系统结构复杂、可靠性差、成本高的问题,基于光纤陀螺(FOG)捷联惯导系统(SINS),采用卫星、天文2级组合导航,提出了实现载体导航信息精密测量的新方法,给出了组合导航系统的滤波结构、误差方程、数学模型。数据分析与精度评估的结果表明,采用小型化、高可靠性、低成本的FOG SINS的组合导航方法能够实现载体速度、位姿的精密测量。基于FOG SINS的载体位姿的精密测量方法是实现导航低成本、高性能的一种有效途径。     

基于数字图像的高精度面内转角测量方法

针对科研与工程中转角测量优于5″的高精度要求,提出了一种用直线做特征标志的基于图像的测量方法。用高分辨率相机采集被测物上长直线标志,通过高精度检测图像上直线的倾斜角度来计算转角。分析了基于图像高精度角度测量中出现的多种原来无需考虑的影响精度的因素。给出了角秒级角度测量时直线的拟合检测算法以及直线标志的成像宽度、长度、与采样方向的角度等参量的选择应满足的条件。仿真和实验结果表明直线宽度5~9 pixel,直线方向避开与采样方向成0°和45°角时角度检测精度达到最优,当直线长度不小于1000 pixel时测量精度优于5″。     

基于机器视觉的雷达测角精度评估系统

利用光学成像原理,设计了基于机器视觉的雷达测角精度评估系统,主要包括光学部分(CCD相机)、图像采集部分和图像处理与目标角度信息提取部分等;机器视觉的定位成像和高精度测角,保证了该系统能在紧缩场中对雷达系统进行自动化、高精度、实时的角度测量校准和测量精度评估试验;理论分析和仿真结果表明,补偿由于雷达系统和机器视觉系统安装位置不同引起的角度测量偏差后,在正常的实验测量误差条件下,基于机器视觉的角度测量校准和评估系统能达到0.005°的校准和评估精度。     

机载北斗/GPS/SINS组合导航系统软硬件设计

针对单一导航导航系统在导航精度、稳定性、设备成本以及导航信息完备性等方面的局限性,设计了卫星导航/惯性导航组合导航系统。针对GPS导航系统受制于人及北斗导航系统发展尚不完善的特点,提出了基于北斗/GPS/SINS的军用机载组合导航系统软硬件设计。搭建了北斗/GPS/SINS组合导航系统硬件平台,采用基于不确定度的加权平均数据融合算法提高组合导航系统的导航可靠性和准确性。仿真结果表明,该组合导航系统稳定性好,可靠性高,定位准确。     

基于PSD的风洞模型姿态角光学测量技术研究

开发了一种基于光电探测技术的风洞模型姿态角光学测量技术,实现了对姿态角的精确、实时、非接触测量。对激光探测头、模拟试验平台进行了优化设计,编写了功能齐全的实验软件,模拟了风洞试验运行实况,深入开展了一维和二维角度测量实验和分辨率测试实验。实验结果表明,该技术可对模型变化角度进行实时精确测量,测量范围达到了-10°～10°,测量精密度为0.0023°,测量准确度为0.0026°,分辨率可达到0.001°。该光学测量技术在风洞模型的角度测量和振动测量实验中切实可行,为测量风洞试验模型的姿态及振动提供了一种简洁有效的测量方法。     

基于正弦波磁光调制的方位失调角精确测量方法

针对传统基于正弦波磁光调制的方位失调角测量系统存在测量精度不高的问题,提出了一种新的系统方位失调角测量模型以提高系统测量精度。通过分析传统的基于正弦波磁光调制的方位失调角测量原理发现,由于采用省略高阶项的贝塞尔函数展开式表示磁光调制后的信号,引入了信号截断误差和方法误差,影响了系统测量精度。在分析基础上推导建立了一种基于纯三角函数表示的无理论误差的方位失调角测量新模型并进行了仿真。仿真结果表明,利用推导建立的失调角测量新模型,系统测量精度明显高于传统方法,这对重新理解基于正弦波磁光调制的方位失调角测量系统原理、提高系统测量精度具有一定的参考意义。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.