Magnetotransport properties of epitaxial Pr0.5Ca0.5MnO3 films grown by a solution technique

Epitaxial Pr_0.5Ca_0.5MnO₃ films have been synthesized on (0 0 1) SrTiO₃ substrate using a chemical solution deposition technique and two-step post-annealing process. The zero field resistivity of the films shows semiconducting behavior and a characteristic of charge ordering is observed at 230 K. The resistivity of the 10 nm film did not show any effect with the magnetic field. However, melting of charge ordering was observed for the 120 nm film at an applied magnetic field of 4 T. Large decrease in the resistivity of the 120 nm film (<100 K) resulted in magnetoresistance of nearly −100% at 75 K.     

Dielectric and structural relaxation phenomena in Na0.5Bi0.5TiO3 single crystal

Abstract

Dielectric permittivity studies of Na_0.5Bi_0.5TiO₃ single crystals in a broad range of frequency up to 10 MHz and temperature 300—823 K are reported. In this temperature range dielectric dispersion below 1 MHz has been found. The obtained data were fitted to the Cole-Cole relation. The mean relaxation time τ is strongly temperature dependent (0.04 ? 2.6 × 10^?5 s). A remarkable hysteresis effect in the values of τ on cooling and heating took place. The Δε(T) dependence (the maximal value of Δε ～ 400) is similar to the global ε′(T) response at low frequency. An isothermal structural transformation in Na_0.5Bi_0.5TiO₃ was observed by X-ray measurements. The order of the time in which the transformation takes place (～300 minutes) corresponds to the time in which the strongest time evolution of electric permittivity and time changes of dielectric dispersion were detected.     

First principles study of Ca in BaTiO3 and Bi0.5Na0.5TiO3

BaTiO₃–Bi_0.5Na_0.5TiO₃ is one of the promising candidates as a high-temperature relaxor with a high Curie temperature and several preferred dielectric characteristics. It has been found experimentally for a long time that adding calcium to BaTiO₃–Bi_0.5Na_0.5TiO₃ improves its temperature characteristic of the capacitance [J. Electron. Mater. 39, 2471]. In this study, Calcium (Ca) defects in perovskite BaTiO₃ and Bi_0.5Na_0.5TiO₃ have been studied based on first-principles calculations. In both BaTiO₃ and Bi_0.5Na_0.5TiO₃, our calculations showed that Ca atom energetically prefers to substitute for the cations, that is Ba, Bi, Na and Ti, depending on the growth conditions. In most cases, Ca predominantly substitutes on the A-site without providing additional electrical carriers (serve as either neutral defects or self-compensating defects). The growth conditions where Ca can be forced to substitute for B-site (with limited amount) and the conditions where Ca can be forced to serve as an acceptor are identified. Details of the local structures, formation energies and electronic properties of these Ca defects are reported.     

Glassy-ferromagnetic behavior in Eu0.5Sr0.5CoO3

Polycrystalline perovskite cobalt oxide Eu_0.5Sr_0.5CoO₃ was prepared by the conventional solid-state reaction method. X-ray powder patterns indicated the prepared samples are pure, cubic perovskite structure (Pm3?m), and with no evidence of any secondary phases. The dc magnetization and ac susceptibility measurements were carried out to investigate the magnetic properties of the sample, and which indicated that cluster-glasses properties are suppressed with the increasing of the coercive field. We denied the possibility of spin-glasses and the existence of the Hopkinson effect in Eu_0.5Sr_0.5CoO₃ through the temperature-dependent ac susceptibility measurements, and explained the magnetic behavior of Eu_0.5Sr_0.5CoO₃ with the competition between magnetic anisotropy and the external magnetic field.     

Bi0.5Ba0.5Fe0.5Ti0.49Nb0.01O3热敏陶瓷的微结构和电学性能研究

采用固相合成工艺,制备了Bi_05Ba_05Fe_05Ti_049Nb_001O₃（BBFTN）热敏陶瓷,借助X射线衍射仪、扫描电子显微镜、阻温测试仪和交流阻抗谱考察其微结构、直流电阻、介电特性、阻抗和电学模量方面的电学性能. 结果表明：BBFTN材料依然为立方钙钛矿结构,平均晶粒尺寸约为10 μm,晶格常数相对于BaTiO₃的晶格常数有所变大;室温电 关键词： 05Ba_05Fe_05Ti_049Nb_001O₃')" href="#">Bi_05Ba_05Fe_05Ti_049Nb_001O₃ 微结构 电学性能     

Preparation of LiNi0.5Mn0.5O2 cathode materials by urea hydrolysis coprecipitation

Layered LiNi_0.5Mn_0.5O₂ has been successfully synthesized via urea hydrolysis coprecipitation method. Well-crystallized LiNi_0.5Mn_0.5O₂ was obtained after calcinations of coprecipitation precursors and lithium salts at 450 °C for 3 h and following 900 °C for 10 h in air. Both the precursors and LiNi_0.5Mn_0.5O₂ powders show an agglomerated secondary structure with crystalline particles inside. The quasi-spherical morphology of the precursors was maintained during the calcinations. The first charge and discharge capacities of as-prepared LiNi_0.5Mn_0.5O₂ were 200 and 165mAh/g respectively. The discharge capacity of about 160mAh/g was retained after 10cycles for as-prepared samples.     

Pr0.5Ca0.5MnO3/Si异质结输运特性和整流特性研究

利用固相反应法制备Pr_0.5Ca_0.5MnO₃(PCMO)靶材,并采用脉冲激光沉积法(PLD)在n型Si(111)基片上沉积PCMO外延薄膜,研究了薄膜的输运特性及薄膜与Si衬底形成异质结的整流特性.结果表明:在80—300 K温度范围内,PCMO薄膜的阻温关系符合变程跳跃模型,随着温度的升高表现出从一维到二维再到三维的转变,分析认为可能源于轨道自由度对电子输运特性的影响.PCMO/Si异质结在磁场作用下整流特性得到改善,且在正向电流方向出 关键词： 0.5Ca_0.5MnO₃')" href="#">Pr_0.5Ca_0.5MnO₃ Si 整流 正磁电阻     

Physical properties of the doped manganites Ln0.5M0.5Mno3 (Ln = Pr,La; M = Sr,Ca, Ba)

We present the structural, magnetic and electrical properties of some manganese oxides such as Ln_0.5M_0.5MnO₃ (Ln = La, Pr and M = Ca, Sr, Ba) in which the average ionic radius <r_A> of the A site cation is varied while keeping the Mn³⁺/Mn⁴⁺ ratio fixed to 1. All the studied samples have a perovskite structure with rhombohedral or orthorhombic distortion. This distortion was related to the A cation size. The lattice volume increases lineraly with ( r _A) in all the range 1.179–1.3264 Å. The magnetic investigation shows that the magnetic transition temperature T _t, and magnetisation saturation M _s have similar behaviour by increasing and decreasing with (r _A). The electrical measurements show conduction by small polarons attributed to a large canting angle 9 in all the range 4–300 K in the two ferromagnetic compounds La_0.5Sr_0.5MnO₃ and La_0.5Sr_0.5MnO₃.     

0.5NdAlO3-0.5CaTiO3电子结构及光学性质的第一性原理计算

采用基于第一性原理密度泛函理论的平面波赝势方法,对0.5NdAlO₃-0.5CaTiO₃晶体进行结构优化,并对其能带结构,态密度和光学性质进行了理论计算.结构优化后晶格参数与实验数据相符合,误差小于1%;能带计算结果表明0.5NdAlO₃-0.5CaTiO₃为间接带隙,带隙值为0.52eV;费米面附近的能带由Nd-4f,O-2p,Nd-4p,Al-3p,Ti-4d层的电子态密度确定.同时也计算了该结构的介电函数,反射率和复折射率等光学性质.     

A位等价与非等价取代对(K0.5Na0.5)NbO3陶瓷极化的影响

研究了在铌酸钾钠基陶瓷中,A位等价与非等价取代对陶瓷极化温度和极化电场的影响,结果表明:A位等价取代的陶瓷对极化温度和极化电场没有强烈依赖性,可以使极化足够充分,能有效提高铌酸钾钠基陶瓷的压电性能;相反,A位非等价取代的陶瓷对极化温度和极化电场敏感,容易击穿,极化不充分,限制了铌酸钾钠基陶瓷的压电性能. 关键词： 铌酸钾钠 极化 压电     

Bi0.5Ba0.5FeO3 陶瓷的电性能及阻抗分析

以传统的固相反应法制备了Bi_0.5Ba_0.5FeO₃陶瓷,并采用X射线衍射仪、扫描电子显微镜、直流阻温测试仪和交流阻抗分析仪测试了Bi_0.5Ba_0.5FeO₃陶瓷的微结构和电性能.分析结果表明:Bi_0.5Ba_0.5FeO₃陶瓷具有立方钙钛矿结构,颗粒尺寸约1.0 μm;在16—280 ℃范围内,Bi_0.5Ba_0.5FeO₃陶瓷表现出明显的负温度系数热敏效应,其热敏常数、活化能分别为6490 K及0.558 eV;介电温谱揭示,在280 ℃下Bi_0.5Ba_0.5FeO₃陶瓷材料没有出现相变行为.对于交流阻抗谱,采用3个串联的RQ(R与Q为并联)等效部件来拟合分析,拟合结果表明拟合数据与实验数据高度匹配,且这3个等效部件分别代表晶界、晶粒和晶壳的贡献.3个部件中,晶粒对陶瓷电阻阻值的影响最大,晶壳贡献次之,晶界最小,且3个部件电阻值都显示出负温度系数效应.在25—115 ℃范围内,电学模量虚部峰频与阻抗虚部峰频始终不匹配,意味着Bi_0.5Ba_0.5FeO₃陶瓷体内部一直表现出局域导电机理. 关键词： 0.5Ba_0.5FeO₃陶瓷')" href="#">Bi_0.5Ba_0.5FeO₃陶瓷 电性能 阻抗分析     

Influence of epitaxial growth on phase competition in Pr0.5Sr0.5MnO3 films

A series of Pr_0.5Sr_0.5MnO₃ (PSMO) films with various thickness were epitaxially grown on substrates of (0 0 1)-oriented (LaAlO₃)_0.3(SrAl_0.5Ta_0.5O₃)_0.7 (LSAT), LaAlO₃ (LAO) and SrTiO₃ (STO), and (0 1 1)-oriented STO using pulse laser deposition. Influence of epitaxial growth on phase competition was investigated. A ferromagnetic metal to antiferromagnetic insulator (FMM-AFI) transition upon cooling is present in both largely compressed situations deposited on LAO (0 0 1) and tensile cases deposited on STO (0 0 1) but absent in little strained films grown on LSAT (0 0 1), indicating that the antiferromagnetic insulating state is favored by strains. On the other hand, the 400 nm films deposited on (0 1 1)-oriented STO as well as LAO substrates show FMM-AFI transition. These results reveal that both the orientation of epitaxial growth and substrate-induced strain affect the FMM-AFI transition.     

Photoluminescence at room temperature in Ba0.5Sr0.5TiO3 ceramics

We present in this paper the experimental results of photoluminescence spectra of Ba_0.5Sr_0.5TiO₃ ceramics. An emission band centered at about 920 nm has been observed at room temperature. When we change the amount of oxygen vacancies in these samples by thermal treatment, these samples show an enhancement of luminescence. Our experimental results indicate that the origin of the photoluminescence is related to the oxygen vacancies in these samples.     

First-principle study of electronic structure and stability of Sn0.5Sb0.5O2

A theoretical study on Sb-doped SnO₂ has been carried out by means of periodic density functional theory (DFT) at generalized gradient approximation (GGA) level. Stability and conductivity analyses were performed based on the formation energy and electronic structures. The results show that Sn_0.5Sb_0.5O₂ solid solution is stable because the formation energy of Sn_0.5Sb_0.5O₂ is −0.06 eV. The calculated energy band structure and density of states showed that the band gap of SnO₂ narrowed due to the presence of the Sb impurity energy levels in the bottom of the conduction band, namely there is Sb 5s distribution of electronic states from the Fermi level to the bottom of conduction band after the doping of antimony. The studies provide a theoretical basis to the development and application of Sn_1−xSb_xO₂ solid solution electrode.     

NbTi0.5Ni0.5O4 as anode compound material for SOFCs

NbTi_0.5Ni_0.5O₄ (NTNO) has been prepared using solid state synthesis and investigated as a potential anode material. The oxide form of NTNO has single phase rutile-type structure with tetragonal (P42/mnm) space group. The reduced form is a composite of nano-scaled particles of metallic Ni and Nb_1.33Ti_0.67O₄ phase. Reduced NTNO showed high electronic conductivity up to 280 S.cm^− 1 at 900 °C in reducing atmosphere, but suffers from low CTE equal to 3.78 10^− 6 K^− 1. Studies of NTNO as anode material were carried out in a three electrode - electrochemical half cell configuration under pure humidified H₂ at 900 °C using a 2 mm thick zirconia electrolyte and without any additional current collector material. The results show a reasonable series resistance (R_s) equal to 2.7 Ωcm² (about 50% higher than for metallic gold layers) indicating a good current collection performance for a 10 μm layer of material. The polarization resistance (R_p) was equal to 33 Ωcm² and is attributed to a poor density of three phase boundaries (TPB) and shortage of oxide ion conduction in the anode layer. The results show the potential of NTNO as an anode material, especially after optimization of the microstructure towards the increase of TPB length.     

立方(Ba0.5Sr0.5)TiO3高压诱导带隙变化的第一性原理研究

采用基于密度泛函理论(DFT)的第一性原理计算研究了 (Ba_0.5Sr_0.5)TiO₃ (BST) 晶体在高压下的电子结构及能带变化行为. 研究结果发现,随着压强的增加,BST能带间隙先增加,在压强为55 GPa时达到最大值,然后减小,这些有趣的结果将有助于开发与设计新的BST铁电器件. 进一步地,通过电子态密度和密度分布图的研究分析可知:在低压区域(055 GPa),则是出现的离域现象占主导(电子的离域作用超过键态的作用),从而使带隙减小. 关键词： 钛酸锶钡 第一性原理 高压 能带间隙     

Site occupation of doping La3+ cations and phase transition in Na0.5Bi0.5TiO3–BaTiO3 solid solution

The effects of La doping on the ferroelectric properties of 0.92Na0.5Bi0.5TiO3-0.08BaTiO3(NBT-BT) solid solution have been studied both experimentally and theoretically.The experimental results show that an abnormal ferro-toantiferroelectric phase transition is induced by La doping in NBT-BT.The first-principles calculations indicate that La3+ cations selectively substitute for the A site in NBT-BT as donors.Furthermore,the computed binding energy reveals that La cations is most likely to substitute Ba 2+or Na+,not Bi3+,at A site as donors in NBT-BT,as supported by our Raman spectra.The ferro-to-antiferroelectric phase transition of La-doped NBT-BT is believed to originate from the lattice aberrance and redistribution of valence electrons,thus strengthening the bonding of A-O,enhancing the hybridization between the A cation d orbital and O 2p orbital,and resulting in the deflection of the polar direction of NBT-BT lattice.     

Microstructures and microwave dielectric properties of La1-xBx(Mg0.5Sn0.5)O3 ceramics

The microwave dielectric properties of La_1-xB_x(Mg_0.5Sn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La_1-xB_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La_0.995B_0.005(Mg_0.5Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. A maximum apparent density of 6.58 g/cm³, a dielectric constant (ε_r) of 19.8, a quality factor (Q × f) of 41,800 GHz, and a temperature coefficient of resonant frequency (τ_f) of −86 ppm/°C were obtained for La_0.995B_0.005(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h.     

Transverse laser induced thermoelectric voltage effect in tilted La0.5Sr0.5CoO3 thin films

The transverse laser induced thermoelectric voltage effect has been investigated in tilted La_0.5Sr_0.5CoO₃ thin films grown on vicinal cut LaAlO₃ (1 0 0) substrates when films are irradiated by pulse laser at room temperature. The detected voltage signals are demonstrated to originate from the transverse Seebeck effect as the linear dependence of voltage on tilted angle in the range of small tilted angle. The Seebeck coefficient anisotropy ΔS of 0.03 μV/K at room temperature is calculated and its distorted cubic structure is thought to be responsible for this. Films grown on a series of substrates with different tilted angles show the optimum angle of 19.8° for the maximum voltage. Film thickness dependence of voltage has also been studied.