飞秒激光烧蚀铝靶产生喷射物的超快脉冲数字全息诊断

采用脉冲数字显微全息技术,对50 fs单脉冲激光烧蚀铝靶过程中的物质喷射以及等离子体演化的动态过程进行了实验研究,获得了高时空分辨的动态数字全息图.由全息图观察到了热弹力波引起的二次喷射现象,并且报道了大延迟下喷射物质对400 nm探测光所引起的干涉条纹的反常移动现象.通过对全息图进行数字再现,得到了不同延迟下探测光穿过等离子体后的二维相位分布,并运用逆Abel变换算法获得了等离子体折射率以及等效电子密度的时空演化动态过程.根据实验以及计算所得到的有关于喷射物的光学性质,对喷射物的结构和成分进行了分析. 关键词： 脉冲数字全息 飞秒激光烧蚀 超快时间分辨 等离子体     

强非局域空间光孤子大相移的理论研究以及应用方案设计

本文发展了郭旗等人的唯像理论,发现在铅玻璃中,孤子随着本身功率或者抽运光孤子功率几十个毫瓦的变化,就会出现π的附加相移.基于抽运光孤子功率对弱信号光孤子相位有着高调制灵敏度的结论,提出了一种较可行的光开关实现方案. 关键词： 强非局域 空间光孤子 大相移     

超短激光脉冲驱动的Thomson散射空间分布特性

研究了超短激光脉冲驱动的Thomson散射的辐射空间分布. 发现辐射的空间分布对称性显著地依赖于超短脉冲的载波相位η₀，在η₀＝0，π时，辐射的空间分布呈现出二重或一重对称性；而在其他载波相位时，这些空间分布对称性遭到破坏. 辐射光的准直性也依赖于驱动脉冲的载波相位，在η₀＝±π/2时辐射光的准直性最好. 这些结果表明可以通过改变驱动激光脉冲的载波相位来控制辐射光的空间分布，也可以利用辐射空间分布对相位的依赖特性来测量超短激光脉冲的载波相位. 关键词： Thomson散射 空间分布 载波相位     

LD端面抽运c切Nd:YVO4自拉曼倍频589 nm黄光激光研究

报道了LD端面抽运c切Nd:YVO₄自拉曼倍频黄光激光器的研究. 采用10 mm长,二类临界相位匹配角 (θ=69°,ø=0°)切割的KTP晶体作为倍频晶体. 考虑到c切Nd:YVO₄跃迁截面较小,所以通过对谐振腔及晶体膜系的严格设计,减少腔内插入损耗和衍射损耗. 最终在脉冲重复率为10 kHz,抽运功率为11.2 W下,获得了最高570 mW的倍频黄光激光输出,对应抽运光到倍频黄光的转化效率约为 关键词： 拉曼激光 c切Nd:YVO₄')" href="#">c切Nd:YVO₄ 589 nm 黄光激光     

激光烧蚀对碳纳米管薄膜场发射性能的影响

采用丝网印刷工艺制作了碳纳米管(CNTs)薄膜阴极.经适当能量激光烧蚀后,相互粘连的CNTs随表面粘附有机物的蒸发而分散开,管间隙增加、屏蔽效应减小,使得场发射性能大幅度提高,开启场强降低、场倍增因子β增大.Raman光谱分析表明,随激光能量增加,CNTs表面缺陷增多,成为新的场发射点,对其β增大的贡献加强.相对于两电极结构,三电极中平栅极结构场发射性能经激光烧蚀有更显著的改善.这说明激光烧蚀是提高CNTs场发射性能的有效方法. 关键词： 碳纳米管薄膜 场发射 激光烧蚀 Raman光谱     

大气环境下飞秒激光对铝靶烧蚀过程的研究

利用时间分辨的光阴影成像技术研究了在大气环境下飞秒激光烧蚀铝靶的动态过程. 在入射激光能量为4 mJ, 激光光斑超过1 mm时, 激光烧蚀区表面物质以近似平面冲击波形式向外喷射; 在同样激光能量下、激光光斑较小时(约0.6 mm), 激光烧蚀区以近似半球型冲击波形式向外喷射. 当激光能量比较大时(7 mJ), 发现空气的电离对于激光烧蚀靶材有着重要影响. 在光轴附近烧蚀产生的喷射物具有额外的柱状和半圆型的结构, 叠加在平面冲击波结构上.     

色散效应对光学参量放大器量子起伏特性的影响

解析求解了包含色散、损耗和抽运吃空的含时的Fokker-Planck方程,通过数值计算首先获得了色散时简并参量放大(DOPA)系统的光压缩特性.研究结果表明：色散效应是由非线性极化率从χ″增大到χ″/{1+σ²/}/+2而引起的.随着色散效应的逐渐增大,压缩曲线的形状基本相同,且整体向左收缩,最大压缩趋近于线性理论的结果1/(1+μ).还获得了色散时非简并参量放大(NOPA)系统的光纠缠特性.研究发现：当σ给定,随着抽运参数μ的增大,相应的相位变化也增大,非线性极化率的极性发生多次变化,极性为正阶段的增益大部分被极性为负阶段的衰减所抵消,净增益不大,压缩也不大,最小均方差V₁的值逐渐减小,且整体向右移动,接近于线性理论的结果1/(1+μ). 关键词： 色散 量子起伏 光学参量放大器     

超短脉冲激光烧蚀石墨产生的喷射物的时间分辨发射光谱研究

本文使用不同激光能流(18 J/cm²–115 J/cm²)和脉冲宽度(50 fs–4 ps)的超短脉冲激光在真空中(4×10^-4 Pa)烧蚀高定向热解石墨. 通过测量烧蚀喷射物的时间分辨发射光谱研究喷射物的超快时间演化. 在喷射物发射光谱中, 观察到了C₂基团的天鹅带光谱系统, 416 nm附近C₁₅基团的由电子能级¹Σ_u⁺ 和¹Σ_g⁺之间的振动跃迁产生的光谱峰以及连续谱. 50 fs, 115 J/cm²的脉冲激光烧蚀产生的喷射物的连续谱的强度衰减分为快速下降和慢速下降两个阶段(以20 ns时间延迟为分界). 这表明连续谱是由两种不同的组分贡献的. 快速下降阶段, 连续谱主要由碳等离子体通过韧致辐射产生; 慢速下降阶段, 连续谱主要由烧蚀后期产生的大颗粒碳簇的热辐射贡献. 实验结果还揭示了激光能流的提高, 会明显增加喷射物中碳等离子体和激发态C₂的含量, 但对质量稍大的C₁₅的影响较小; 此外, 50 fs脉冲激光烧蚀产生的连续谱的存在时间会随着激光能流的减小而增大, 这说明低能流更有利于在烧蚀后期产生碳簇. 脉宽主要影响喷射物连续谱的时间演化. 4 ps脉冲激光烧蚀产生的连续谱的整个时间演化过程明显慢于50 fs脉冲产生的连续谱.     

纳秒激光单脉冲烧蚀硅表面的超快成像研究

利用ICCD可以在纳秒时间尺度下成像的特点,以飞秒准连续激光产生的超短脉冲光为探测光,对纳秒激光单脉冲烧蚀硅靶表面的演化过程进行动态监测。在能量密度为50J／cm^2时,捕获了纳秒单脉冲激光烧蚀硅靶面过程中等离子体演化的时间分辨图像。图像表明,纳秒激光烧蚀硅靶产生的等离子体开始时密度大,膨胀速度快,当纳秒激光脉冲过后,等离子体不再产生,并且其膨胀速度不再增加,直至完全消失。     

Dy3+掺杂Ge-Ga-S-CsI玻璃中红外发光特性研究

用熔融淬冷法制备了系列掺杂浓度的Dy³⁺:Ge-Ga-S-CsI硫卤玻璃样品,测试了样品拉曼光谱、折射率、吸收光谱、近红外及中红外荧光谱.应用Judd-Ofelt理论计算了Dy³⁺离子的强度参数 (Ω_i, i=2,4,6)、自发辐射跃迁概率(A)、荧光分支比(β)、以及辐射寿命(τ_rad)等光谱参数.研究了810 nm激光抽运下样品中红 关键词： 硫系玻璃 中红外发光 3+掺杂')" href="#">Dy³⁺掺杂 多声子弛豫     

稀土材料的超快共振非线性光学特性研究

用抽运-探测技术测量光学响应材料非线性极化率的方法，研究了稀土材料非线性折射率的共振增强和超快响应的非线性动力学过程。测得钕玻璃的三阶非线性折射 率强度系数为10^-14cm^2/W，比其基质的非线性折射率强度系数提高了2个量级。用该方法研究了Nd:YVO4、Er:YAG等晶体的超快非线性响应过程。实验结果与理论分析表明，抽支-探测技术是测量非线性极化率的简单而又灵敏的方法。这一测量技术对研究与开发超高速光响应器件具有重要的实用价值。     

Phase-and spin-dependent manipulation of leakage of Majorana mode into double quantum dot

We present a phase-and spin-dependent manipulation of leakage of a Majorana mode into a double quantum dot. We study the density of states(DOS) to show the effect of phase change factor on the Majorana leakage into(out) of a double quantum dot. The DOS is derived from the Green's function of the quantum dot by the equation of motion method, and exhibits a formant structure when φ = 0, 2π and a resonance shape when φ = 0.5π and 1.5π. Also, it changes more strongly under the spin-polarized coefficient than the non-polarized lead. Such a theoretical model can be modified to explore the spin-dependent effect in the hybrid Majorana quantum dot system.     

强飞秒激光烧蚀石英玻璃的超快时间分辨光学诊断

采用超快时间分辨的光学诊断技术对飞秒激光脉冲烧蚀石英玻璃的动态过程进行了实验研究.首先,对烧蚀过程中石英玻璃外部的物质喷射进行了数字全息记录,获得了不同延迟时间下探测光的二维相位差分布图,并由此推断出了喷射物的成分和结构.此外,对石英玻璃内部的现象进行了时间分辨阴影图记录,从阴影图中观察到了石英玻璃内部的两个应力波的演化过程.这两个应力波与目标靶外部的两次物质喷射相关. 关键词： 脉冲数字全息 飞秒激光烧蚀 超快时间分辨 应力波     

Laser phase effect on asymmetric harmonic distribution in H_2~+

The laser phase effect on the spatial distribution of the molecular high-order harmonic generation(MHHG) spectrum from H_2~+ is theoretically investigated through solving the Non-Bohn-Oppenheimer(NBO) time-dependent Schrodinger equation(TDSE).The results are shown as follows,(i) The generated harmonics from the two nuclei each present an asymmetric distribution.Particularly,when the laser phases are chosen from 0.0π to 0.6π and from 1.7π to 2.0π,the contribution from the negative-H plays a main role in harmonic generation.When the laser phases are chosen from 0.7πto 1.6k,the contribution from the positive-H to the harmonic generation is remarkably enhanced and becomes greater than that from the negative-H.The electron localization,the time-frequency analyses of the harmonic spectrum and the time-dependent wave function are shown to explain the asymmetric harmonic distribution in H_2~+,which provides us with a method to control the electron motion in molecules,(ⅱ) As the pulse duration increases,the asymmetric distributions of the MHHG in two H nuclei decrease,(ⅲ) Isotope investigation shows that the asymmetric harmonic distribution can be reduced by introducing the heavy nucleus(i.e.,D_2~+).     

基于零拍探测和压缩真空光输入增强Sagnac效应

利用量子技术增强Sagnac效应提高陀螺输出精度具有重要的研究意义, 是实现全自主导航的重要途径. 以相干态激光作为输入光源的光学陀螺因真空零点波动使其输出精度限制于散粒噪声极限而难以提高. 为减小真空波动的影响, 提出在激光输入的分束器的另一输入端输入压缩真空光并结合平衡零拍探测技术的方法增强Sagnac效应. 理论分析表明Sagnac效应性能得到有效提升: 干涉输出的灵敏度检测极限和动态范围均随着压缩程度的增加而呈指数级增长. 该方法只需对经典光学陀螺做少量改动就可实现, 是提高光学陀螺输出精度的一种新方法.     

Broad-band phase retrieval method for transient radial shearing interference using chirp Z transform technique

The transient radial shearing interferometry technique based on fast Fourier transform (FFT) provides a means for the measurement of the wavefront phase of transient light field. However, which factors affect the spatial bandwidth of the wavefront phase measurement of this technology and how to achieve high-precision measurement of the broad-band transient wavefront phase are problems that need to be studied further. To this end, a theoretical model of phase-retrieved bandwidth of radial shearing interferometry is established in this paper. The influence of the spatial carrier frequency and the calculation window on phase-retrieved bandwidth is analyzed, and the optimal carrier frequency and calculation window are obtained. On this basis, a broad-band transient radial shearing interference phase-retrieval method based on chirp Z transform (CZT) is proposed, and the corresponding algorithm is given. Through theoretical simulation, a known phase is used to generate the interferogram and it is retrieved by the traditional method and the proposed method respectively. The residual wavefront RMS of the traditional method is 0.146λ, and it is 0.037λ for the proposed method, which manifests an improvement of accuracy by an order of magnitude. At the same time, different levels of signal-to-noise ratios (SNRs) from 50 dB to 10 dB of the interferogram are simulated, and the RMS of the residual wavefront is from 0.040λ to 0.066λ. In terms of experiments, an experimental verification device based on a phase-only spatial light modulator is built, and the known phase on the modulator is retrieved from the actual interferogram. The RMS of the residual wavefront retrieved through FFT is 0.112λ, and it decreases to 0.035λ through CZT. The experimental results verify the effectiveness of the method proposed in this paper. Furthermore, the method can be used in other types of spatial carrier frequency interference, such as lateral shearing interference, rotational shearing interference, flipping shearing interference, and four-wave shearing interference.     

初始压入位置对Ni基单晶合金纳米压痕影响研究

针对Ni基单晶合金建立初始压入γ 相的γ /γ' 模型和初始压入γ'相的γ'/γ 模型, 采用分子动力学方法模拟金刚石压头压入两种模型的纳米压痕过程, 计算两种模型[001]晶向硬度. 采用中心对称参数分析两种模型(001)相界面错配位错对纳米压痕过程的影响. 结果显示: 弛豫后, 两种模型(001)相界面错配位错形式不同, 其中γ'/γ 模型(001)相界面错配位错以面角位错形式存在; 压入深度在0.930 nm 之前, 两种模型(001)相界面错配位错变化不大, 压入载荷-压入深度及硬度-压入深度曲线较符合; 压入深度在0.930 nm之后, γ'/γ 模型(001)相界面错配位错长大很多, 导致相同压入深度时γ'/γ 模型比γ /γ'模型压入载荷和硬度计算结果小; 压入深度在2.055 nm之后, γ /γ'模型(001)相界面错配位错对γ 相中位错进入γ'相有阻碍作用, 但仍有部分位错越过(001) 相界面进入γ' 相中, γ'/γ 模型(001)相界面处面角位错对γ' 相中位错进入γ 相有更明显的阻碍作用, 几乎无位错越过(001) 相界面进入γ 相中, 面角位错的强化作用更明显, 所以γ'/γ 模型比γ /γ'模型压入载荷上升速度快.     

Steered coherence and entanglement in the Heisenberg XX chain under twisted boundary conditions

We study steered coherence(SC) and entanglement in a three-spin Heisenberg XX model under twisted boundary conditions and show that their strengths can be significantly enhanced by tuning the twist angle. The optimal twist angle θ_(opt) for achieving the maximum l_1 norm of SC is π in the region of weak field B and decreases gradually from π to 0 when B increases after a critical value, while for the relative entropy of SC, θ_(opt) equals π in the weak field region and 0 otherwise.The entanglement and the critical temperature above which the entanglement vanishes can also be significantly enhanced by tuning the twist angle from 0 to π.     

Automated fine grid technique for measurement of large-strain deformation maps

The fine grid technique has been a standard engineering tool for measuring large strains for many years. The sample surface is marked with a grid, and the deformation of this grid allows the deformation of the sample to be monitored. However, it has never been easy quantitatively to analyse the strain across the whole of a specimen's surface. We describe here an automated approach in which digitised images of a sample prepared with a grid are analysed by the Fourier transform method. This provides phase maps which, when unwrapped, yield planes representing the two in-plane specimen coordinates. An iterative technique follows these deforming planes from one frame to the next as the specimen deforms, allowing displacement fields to be calculated. Numerical differentiation gives strains across the specimen surface. Gerchberg iteration is used to provide immunity to errors resulting from holes or tears in the specimen surface. The method is demonstrated on a propellant simulant containing burn holes (a cylinder of diameter 10 mm; grid PITCH = 76 μm), loaded in compression across a diameter. All in-plane components of strain are calculated up to strains of approximately one-third. Displacement accuracy is of order 1 μm.     

Round-robin differential quadrature phase-shift quantum key distribution

Recently,a round-robin differential phase-shift(RRDPS) protocol was proposed[Nature 509,475(2014)],in which the amount of leakage is bounded without monitoring the signal disturbance.Introducing states of the phase-encoded Bennett-Brassard 1984 protocol(PE-BB84) to the RRDPS,this paper presents another quantum key distribution protocol called round-robin differential quadrature phase-shift(RRDQPS) quantum key distribution.Regarding a train of many pulses as a single packet,the sender modulates the phase of each pulse by one of {0,π/2,π,3π/2},then the receiver measures each packet with a Mach-Zehnder interferometer having a phase basis of 0 or π/2.The RRDQPS protocol can be implemented with essential similar hardware to the PE-BB84,so it has great compatibility with the current quantum system.Here we analyze the security of the RRDQPS protocol against the intercept-resend attack and the beam-splitting attack.Results show that the proposed protocol inherits the advantages arising from the simplicity of the RRDPS protocol and is more robust against these attacks than the original protocol.