基于CuInS2/ZnS核壳结构量子点的高光效暖白光LED

采用逐步热注射法合成了用于白光LED的CuInS₂/ZnS(CIS/ZnS)核壳结构量子点.通过调整Cu/In的比率, 在CuInS₂(CIS)量子点的基础上, 合成了发射波长在570~650 nm之间可调的CIS/ZnS量子点.与CIS量子点的低量子产率相比, 具有核壳结构的CIS/ZnS量子点的量子产率达到了78%.通过在黄光荧光粉YAG :Ce³⁺表面旋涂CIS/ZnS量子点的方式制备了暖白光LED器件.在工作电流为10 mA时, 暖白光LED的发光效率达到了244.58 lm/W.由于CIS/ZnS量子点的加入, 所制备的白光LED器件的显色指数达到86.7且发光颜色向暖色调发生了转移, 相应的色坐标为(0.340 6, 0.369 0).     

核/壳结构的ZnS:Mn/SiO_2纳米粒子的制备及发光性质研究

采用溶剂热法制备了Mn离子掺杂的ZnS纳米粒子(ZnS∶Mn),然后利用正硅酸乙酯(TEOS)的水解反应对其进行了不同厚度的SiO2无机壳层包覆。采用X射线衍射(XRD)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)及荧光发射光谱(PL)对样品的结构及光学性质进行了表征和研究。包覆SiO2壳层后,粒子的粒径明显增大并且在ZnS∶Mn纳米粒子表面可以观察到明显的SiO2壳层。XPS测试印证了ZnS∶Mn/SiO2的核壳结构。随着SiO2壳层的增厚,ZnS∶Mn/SiO2的Mn离子的发光先增强后减弱,这是因为SiO2壳层同时具有表面修饰和降低发光中心浓度这两种相反的作用。当壳层厚度(壳与核的物质的量的比)达到5时,发光效果达到最好,其强度达到未包覆样品的7.5倍。     

核壳型ZnS∶Cu/ZnS量子点的制备及发光性质

本文采用水相合成方法制备了ZnS∶Cu量子点并进行了ZnS壳层修饰,研究了壳层厚度对ZnS∶Cu量子点光学性质的影响,采用TEM、XRD、PL、PLE和UV-Vis等测试方法对其进行了表征。实验结果表明,合成的ZnS∶Cu/ZnS量子点为立方闪锌矿,尺寸分布均匀呈球形,分散性良好,经过壳层修饰平均粒径由2 nm增加到3.2 nm。随着ZnS壳与ZnS核量的比的增加,量子点的PLE激发峰位置和UV-Vis吸收谱线出现红移,也说明了量子点的尺寸增大,证明ZnS在ZnS∶Cu量子点的表面生长,形成了核壳结构的ZnS∶Cu/ZnS量子点。随着壳层增厚,量子点与铜离子发光中心相关的发射峰强度先增大后减小,当壳核比n_s/n_c=2.5时,发光强度达到最大。     

不同壳层厚度的LaF3：Eu3+/LaF3核壳结构纳米颗粒制备及发光性质

表面缺陷会使纳米材料的发光中心产生严重的猝灭，而适当厚度的同质包覆层会减少其猝灭。本文利用共沉淀法合成了LaF₃：Eu³⁺纳米颗粒和LaF₃：Eu³⁺/LaF₃核壳结构纳米颗粒，研究了颗粒的晶体结构、形貌以及不同壳层厚度对发光性能的影响。研究发现：LaF₃：Eu³⁺核心和LaF₃：Eu³⁺/LaF₃核壳结构均为六方结构。包覆同质壳层可以提高稀土离子的发光性能，包覆厚度的不同导致LaF₃：Eu³⁺/LaF₃核壳结构的荧光强度与衰减时间均发生改变。其原因是未掺杂的LaF₃壳层可以将发光中心Eu³⁺离子与LaF₃：Eu³⁺核心的表面隔离，进而减少表面对发光中心的猝灭，提高材料的发光性能。这种修饰作用与壳层厚度相关。     

核-壳结构的ZnS:Mn纳米粒子的荧光增强

采用反胶束方法制备了ZnS :Mn纳米粒子并对其进行了ZnS壳层修饰 ,采用发射光谱和激发光谱对其光学性质进行了研究。与未包覆的ZnS:Mn纳米粒子相比 ,核 壳结构的ZnS :Mn纳米粒子来自于Mn2 离子的 5 80nm的发光增强了数倍 ,归因于ZnS壳增加了Mn2 离子到纳米颗粒表面的距离 ,减弱了Mn2 离子向表面猝灭中心的传递。样品制备后 ,核 壳结构的ZnS :Mn纳米粒子在 5 80nm的发光随时间略有增强 ,激发光谱的位置未发生明显变化 ,而未包覆的ZnS:Mn纳米粒子在 5 80nm的发光显著增强 ,同时自激活发光减弱 ,激发光谱明显发生红移 ,说明未包覆的ZnS :Mn纳米粒子的尺寸随时间增大 ,而核 壳结构的ZnS :Mn纳米粒子尺寸基本不变。     

CdSe/ZnSe/ZnS多壳层结构量子点的制备与表征

展示了一种简捷的多壳层量子点合成路线。在含有过量Se源的CdSe体系中直接注入Zn源,"一步法"合成了CdSe/ZnSe量子点;进一步以CdSe/ZnSe为"核",表面外延生长ZnS壳层制备了核/壳/壳结构CdSe/ZnSe/ZnS量子点。相对于以往报道的多壳层结构量子点的制备方法,该方法通过减少壳层的生长步骤有效地简化了实验操作,缩短了实验周期,同时减少对原料的损耗。对量子点进行高温退火处理,能够大幅提高CdSe/ZnSe/ZnS量子点的发光量子产率。透射电镜、XRD以及光谱研究表明:所制备的量子点接近球形,核与壳层纳米晶均为闪锌矿结构,最终获得的CdSe/ZnSe/ZnS量子点的光致发光量子产率达到53％。为了实现量子点的表面生物功能化,通过巯基酸进行了表面配体交换修饰,使量子点表面具有水溶性的羧基功能团,并且能够维持较高的光致发光量子产率。     

铜铟硫纳米晶/PMMA复合薄膜的制备与光学性质表征

铜铟硫(CuInS₂)纳米晶具有发射光谱宽、波长易于调控、量子产率高、合成成本低、容易与封装材料复合等优点,在远程白光LED结构中具有广阔的应用前景。远程白光LED结构是针对LED散热问题提出的一种新型封装结构,在这种结构中复合荧光涂层(复合薄膜)与蓝光芯片进行隔离封装,这种结构对复合薄膜中纳米晶的热稳定性的要求大大降低。首先合成出了不同发光波长的CuInS₂纳米晶荧光材料,然后将其封装到PMMA基质中制备了系列的CuInS₂纳米晶/PMMA复合薄膜。通过荧光光谱和紫外可见光谱的方法,针对纳米晶复合薄膜出现的发光波长红移以及不同发光波长纳米晶/PMMA复合薄膜透过率不一致的现象进行了详细研究。     

SiO2包覆对ZnS纳米材料发光的增强机制

为了明确团聚现象及表面性质对ZnS纳米材料发光性质的影响,采用SiO₂对ZnS材料进行了表面修饰,并对ZnS及ZnS/SiO₂复合材料的光学性质进行对比研究.采用吸收光谱分析了包覆前后光吸收性质的差异,发现SiO₂包覆后ZnS纳米材料的带边由333 nm红移至360 nm.为了研究ZnS纳米材料与ZnS/SiO₂纳米复合材料的光发射性质,分别对含纳米材料的水溶液样品及粉末样品的发光光谱进行了采集.对比研究的结果表明,SiO₂包覆后ZnS纳米材料在蓝紫光区的发光得到了明显增强.以氙灯作为激发光源所获得荧光光谱显示ZnS/SiO₂粉末样品发光的积分强度增大为原来的17.5倍,但相同条件下针对溶液样品的测试结果显示其发光强度只增大了1.1倍,这种增强可用SiO₂的存在抑制了ZnS纳米粒子间的团聚来解释,且这一推断由325 nm紫外激光激发下获得的光致发光数据进行了验证.     

ZnSe(ZnS)纳米晶与MEH-PPV的共掺有机电致发光器件

采用水相法合成核壳结构ZnSe/ZnS 纳米晶,经X射线衍射(XRD)分析和透射电子显微镜(TEM)表征,证实所制备的样品为立方晶型闪锌矿结构ZnSe/ZnS量子点。按照一定的质量比将ZnSe/ZnS 纳米晶和有机聚合物MEH-PPV(poly ) 共掺并将其作为发光层,分别制备单层和多层有机电致发光器件,结构为ITO/MEH-PPV∶ZnSe(ZnS)(50 nm)/Al和 ITO/PEDOT∶PSS(70 nm)/ MEH-PPV∶ZnSe(ZnS)(50 nm)/BCP(15 nm)/Alq₃(12 nm) /LiF(0.5 nm)/Al。实验结果表明,多层发光器件的发光特性与单层器件不同,工作电压的增大使其发光峰发生了明显的蓝移。     

空穴传输材料对CdSe核壳量子点的荧光影响

用稳态光谱和时间分辨光谱技术研究了空穴传输材料对CdSe/ZnSe 与CdSe/ZnS核壳量子点的荧光影响。结果表明,空穴传输材料对量子点有较强的猝灭作用,随空穴传输材料分子浓度的增加,量子点的荧光强度明显地被猝灭,同时量子点的荧光寿命也被减短。两种不同空穴传输分子对CdSe/ZnSe量子点的荧光猝灭明显不同。在与相同空穴传输分子相互作用时,包覆ZnS壳层的CdSe核壳量子点荧光猝灭效率明显低于包覆ZnSe壳层的CdSe核壳量子点。量子点的荧光猝灭过程可以解释为静态猝灭和动态猝灭过程,其中静态猝灭来源于量子点表面与空穴传输材料间相互作用,而动态猝灭则主要来源于量子点到空穴传输材料的空穴转移过程。实验结果表明空穴传输材料的种类以及核壳量子点的壳层结构都对其荧光猝灭效应起关键作用。     

ZnCuInS/ZnSe/ZnS量子点发光光谱特性的研究

ZnCuInS/ZnSe/ZnS量子点是一种无毒,无重金属的“绿色”半导体纳米材料。在研究中,制备了三种尺寸的ZnCuInS/ZnSe/ZnS核壳量子点,其直径分别为3.3,2.7,2.3 nm。通过测量不同尺寸的ZnCuInS/ZnSe/ZnS量子点的光致发光光谱,其发射峰值波长随尺寸的减小而蓝移。其吸收峰值波长和发射峰值波长分别是510,611(3.3 nm),483,583(2.7 nm)以及447,545 nm(2.3 nm)。ZnCuInS/ZnSe/ZnS量子点具有显著的尺寸依赖效应。ZnCuInS/ZnSe/ZnS量子点的斯托克斯位移分别为398 meV(3.3 nm),436 meV(2.7 nm)以及498 meV(2.3 nm),这样大的斯托克斯位移证明,ZnCuInS/ZnSe/ZnS量子点的发光机制与缺陷能级有关。同时,对直径为3.3 nm的ZnCuInS/ZnSe/ZnS量子点进行了温度依赖的光致发光光谱的测量,当温度为15～90 ℃时,该量子点发射峰值波长随温度的升高而红移,发光强度随温度的升高而降低,说明ZnCuInS/ZnSe/ZnS量子点是以导带能级与缺陷能级之间跃迁为主的复合发光。     

Atomistic tight-binding computations of the structural and optical properties of CdTe/CdX (X=S and Se)/ZnS core/shell/shell nanocrystals

A study of CdTe/CdX (X=S and Se)/ZnS core/shell/shell nanocrystals is carried out using atomistic tight-binding theory and the configuration interaction method to provide information for applications in bioimaging, biolabeling, display devices and near-infrared electronic instruments. The calculations yield the dependences of the internal and external passivated shells on the natural behaviours of CdTe/CdX (X=S and Se)/ZnS core/shell/shell nanocrystals. The reduction of the optical band gaps is observed with increasing numbers of monolayers in the external ZnS shell due to quantum confinement. Interestingly, the optical band gaps of CdTe/CdS/ZnS core/shell/shell nanocrystals are greater than those of CdTe/CdSe/ZnS core/shell/shell nanocrystals. In the presence of an external ZnS-coated shell, electron–hole wave function overlaps, oscillation strengths, ground-state exchange energies and Stokes shift are improved, whereas ground-state coulomb energies and fine-structure splitting are reduced. The oscillation strengths, Stokes shift and fine-structure splitting are reduced with the increase in external ZnS shell thickness. The oscillation strengths, Stokes shift and fine-structure splitting of CdTe/CdS/ZnS core/shell/shell nanocrystals are larger than those of CdTe/CdSe/ZnS core/shell/shell nanocrystals. Reduction of the atomistic electron–hole interactions is observed with increasing external ZnS shell size. The strong electron–hole interactions are more probed in CdTe/CdS/ZnS core/shell/shell nanocrystals than in CdTe/CdSe/ZnS core/shell/shell nanocrystals.     

Improved photoluminescence of ZnS:Mn nanocrystals by microwave assisted growth of ZnS shell

The photoluminescence (PL) of ZnS:Mn nanocrystals was improved greatly by microwave assisted growth of ZnS shell. Under optimized conditions, the luminescence quantum yield of ZnS:Mn nanocrystals increased from 2.8% to 12.1% after the growth of the ZnS shell. Time-resolved fluorescence spectroscopic and electron paramagnetic resonance measurements indicate that the improvement of the dispersivity of the doped Mn ions is responsible for the PL enhancement. Growth of the ZnS shell not only facilitated the diffusion of Mn ions during microwave irradiation but also prohibited the segregation of Mn ions on the particle surface. As a result, more isolated Mn²⁺ ions were produced after the growth of the ZnS shell, and thus the orange luminescence of ZnS:Mn nanocrystals was enhanced greatly.     

Wurtzite and zinc-blende CdSe based core/shell semiconductor nanocrystals: Structure, morphology and photoluminescence

We report comparative study of core/shell nanocrystals based on wurtzite and novel zinc-blende CdSe core. Both wurtzite and zinc-blende CdSe are coated with CdS shell or CdS/ZnS multishell under identical synthetic parameters. Crystal structure analysis finds that CdS shell is wurtzite on either wurtzite or zinc-blende CdSe cores. Morphology and photoluminescence studies exhibit that for zinc-blende CdSe based samples, the shell growth is in fine epitaxy and the obtained core/shell nanocrystals show high quantum yield both before and after surface modification process; while wurtzite CdSe based samples have irregular shape indicating inhomogeneous shell growth, and are with lower quantum yield. Furthermore, in the photoluminescence spectra exited with UV radiation, wurtzite CdSe based samples show side peaks of independently nucleated nanocrystals from the shell material; while samples with zinc-blende CdSe cores are potent in restricting these byproducts, which may attribute to the highly effective arrestment of precursor ions onto the zinc-blende CdSe surface. These features manifest that zinc-blende CdSe is more talented than conventional wurtzite CdSe in achieving core/shell nanocrystals with higher qualities.     

单核/双壳结构CdSe/CdS/ZnS纳米晶的合成与发光性质

以巯基乙酸为稳定剂,在水溶液中合成了单核/双壳结构的CdSe/CdS/ZnS纳米晶。在内核CdSe和外壳ZnS之间的内壳CdS作为晶格匹配调节层,能够很好的改善核/壳界面处的性能,而且,最外层ZnS能够最大程度地使激子受限。用TEM和XPS对纳米晶进行了表征,并且用光致发光光谱和吸收光谱对不同核壳结构的纳米晶的发光性能进行了比较,结果表明单核/双壳结构的纳米晶具有更加优异的发光特性。     

Photoluminescence Characteristics of ZnCuInS-ZnS Core-Shell Semiconductor Nanocrystals

The photoluminescence(PL) characteristics of ZnCuInS quantum dots(QDs) with varying ZnS shell thicknesses of 0, 0.5, and 1.5 layers are investigated systemically by time-correlated single-photon counting measurements and temperature-dependent PL measurements. The results show that a ZnS shell thickness of 1.5 layers can effectively improve the PL quantum yield in one order of magnitude by depressing the surface trapping states of the core ZnCuInS QDs at room temperature. However, the PL measurements at the elevated temperature reveal that the core-shell nanocrystals remain temperature-sensitive with respect to their relatively thin shells.The temperature sensitivity of these small-sized single-layered core-shell nanocrystals may find applications as effective thermometers for the in vivo detection of biological reactions within cells.     

Aqueous Synthesis of Water-Soluble L-Cysteine-Modified Cadmium Sulfide Doped with Silver Ion/Zinc Sulfide Nanocrystals

The water-soluble silver ion-doped cadmium sulfide nanocrystals were synthesized by a co-precipitation technique in aqueous solution using L-cysteine as surface modifier, and then L-cysteine-modified cadmium sulfide doped with silver ion/zinc sulfide core/shell nanocrystals were prepared by zinc sulfide epitaxial coated on surface of silver ion-doped cadmium sulfide nanocrystals. The crystal structure, morphology, and spectral properties of cadmium sulfide doped with silver ion/zinc sulfide nanocrystals were characterized by X-ray power diffraction, transmission electron microscope, infrared spectrum, and photoluminescence spectrum. The results show that the photoluminescence quantum yield of cadmium sulfide doped with silver ion/zinc sulfide nanocrystals is improved greatly after doped with silver ion and coated with zinc sulfide shell. The cysteine modified on the surface of cadmium sulfide doped with silver ion/zinc sulfide nanocrystals renders the nanocrystals water-soluble and biocompatible.     

Facile synthesis of mercaptosuccinic acid-capped CdTe/CdS/ZnS core/double shell quantum dots with improved cell viability on different cancer cells and normal cells

Water-soluble, mercaptosuccinic acid (MSA)-capped CdTe/CdS/ZnS core/double shell quantum dots (QDs) were prepared by successive growth of CdS and ZnS shells on the as-synthesized CdTe/CdS_thin core/shell quantum dots. The formation of core/double shell structured QDs was investigated by ultraviolet-visible (UV–Vis) absorption and photoluminescence (PL) spectroscopy, PL decay studies, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The core/double shell QDs exhibited good photoluminescence quantum yield (PLQY) which is 70% higher than that of the parent core/shell QDs, and they are stable for months. The average particle size of the core/double shell QDs was ～3 nm as calculated from the transmission electron microscope (TEM) images. The cytotoxicity of the QDs was evaluated on a variety of cancer cells such as HeLa, MCF-7, A549, and normal Vero cells by 3-(4,5-dimethyl-2-thiazolyl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) cell viability assay. The results showed that core/double shell QDs were less toxic to the cells when compared to the parent core/shell QDs. MCF-7 cells showed proliferation on incubation with QDs, and this is attributed to the metalloestrogenic activity of cadmium ions released from QDs. The core/double shell CdTe/CdS/ZnS (CSS) QDs were conjugated with transferrin and successfully employed for the biolabeling and fluorescent imaging of HeLa cells. These core/double shell QDs are highly promising fluorescent probe for cancer cell labeling and imaging applications.