微穿孔板复合板型声学超材料的低频吸声

针对单层微穿孔板的低频吸声问题提出了微穿孔板复合板型声学超材料结构。将板型声学超材料置入微穿孔板结构的背腔内部实现结构复合。实验结果表明:在相同背腔厚度下,复合结构的吸声性能整体优于单层微穿孔板结构,其中复合结构的吸声曲线从396~892 Hz均大于0.6,在453 Hz处吸声系数达到0.972。利用有限元方法对复合结构进行了仿真,仿真计算的吸声曲线与实验吸声曲线的趋势基本相同,同时发现低频吸声主要由板型声学超材料与声波相互作用贡献。板型声学超材料的吸声峰值的对应频率处,其等效动态质量密度从正变负。在复合结构内部的微穿孔板和板型声学超材料存在相互耦合作用,使得复合结构的第一峰值发生微小偏移。增加板型声学超材料的质量块重量可以使第一吸声峰值向低频移动;保持总背腔厚度不变,增加板型声学超材料的子腔厚度,也可以使第一吸声峰向低频移动。      

对称折叠通道结构的低频通风吸声体*

为了消除或减少低频噪声,该文 提出了一种低频通风超材料吸声体,该吸声体由对称的折叠通道结构组成,具有深度亚波长、高通风空间占比和低频高效吸声的特性.通过传递矩阵方法、有限元模拟和四麦克风实验法,揭示了对称折叠通道结构通风吸声的物理机制.首先在理论上分析单个吸声体的通风吸声性能并进行了仿真模拟,在共振频率423 Hz附近,吸声系数大于0.9,通风空间占比高达40%.吸声单体的共振频率可通过改变折叠通道的长度来灵活调控,组合多个不同共振频率的吸声单体可以拓宽吸声体的有效吸声带宽.由四个吸声单体组合的通风吸声体可实现314－366 Hz频率范围内的高效声吸收(吸声系数大于0.8),且通风空间占比达到35%,而结构厚度仅为314 Hz时波长的1/10.该低频通风吸声体具有结构简单、结构强度高和容易制造等特点,在低频通风降噪领域有着潜在的应用前景．     

黏弹性材料的动态力学特性及其对覆盖层吸声性能的影响

本文利用标准化动态力学测量手段获得了某种高分子聚合物的动态杨氏模量,并根据时温等效原理对动态杨氏模量与声学测量在频段上的差异加以分析和转换,得到了500—7500 Hz频率范围内该黏弹性材料杨氏模量随频率变化的特性.基于所测得动态杨氏模量,采用有限元方法分析了均匀黏弹材料的吸声性能,并将仿真结果与样品声管实验数据进行对比,验证了测试所得参数的准确性.进一步仿真分析了含有局域共振结构的声学覆盖层吸声性能,并讨论了黏弹性材料的动态特性对其吸声性能的影响,提出了改进水声覆盖层低频宽带吸声特性的建议.     

磁力负刚度薄膜结构低频吸声特性

针对背腔深度较小的薄膜吸声结构难以实现低频吸声的问题,提出了磁力负刚度的解决方法。采用传递矩阵法,建立了负刚度薄膜吸声结构理论模型,分析得出该结构的声阻抗等同与大背腔常规薄膜吸声结构的声阻抗;阻抗管实验验证得出,在一定磁场条件下,不同背腔的负刚度薄膜吸声结构与无负刚度结构相比其共振频率显著下降,吸声系数曲线与理论结构吻合。负刚度机制能够降低薄膜吸声结构的共振频率,用较小背腔实现低频吸声,从而实现薄型低频吸声结构设计。      

基于低频吸声超构材料的复合消声器研究*

针对管道内低频噪声难以抑制的问题，本文基于亥姆霍兹共振腔（HR）阵列吸声板和穿孔管消声器组合，设计了一种复合式宽带消声器。首先利用有限元法仿真分析传统穿孔管消声器，发现中低频消声能力较差，通过嵌入HR阵列吸声板吸收中低频噪声。采用仿真与实验的方式研究吸声板的声学性能：在400-1000 Hz频段内的平均吸声系数达到了0.88。然后对复合式消声器进行数值模拟及3D打印阻抗管实验测试对比：复合式消声器在400-1718Hz频率范围内的平均传递损失为18.15 dB ，最终实现了管道内全频带噪声有效控制。     

基于声场重建的材料吸声系数测量方法

针对现有方法对材料吸声系数进行现场测量时存在低频测量误差大的问题,本文提出了一种利用扬声器线阵列对材料吸声系数进行现场测量的新方法。该方法使用基于能量比值约束的最小二乘法在待测材料表面进行平面波声场重建并结合双传声器传递函数法对材料的吸声系数进行测量。数值仿真表明在100～1600 Hz频率范围内,新方法在未加约束时能够对材料的吸声系数进行准确测量。在半消声室中利用新方法测量了三聚氰胺泡沫的吸声系数,分析了能量比值约束值对测量结果的影响,并和阻抗管以及其它两种现场测量方法的测量结果进行了对比。结果表明该方法能够对吸声材料在160～1600 Hz频段内的吸声系数进行准确测量,并且相较于现存的现场测量方法,新方法具有更低的测量频率下限。     

一体化有源吸声终端实现及其在行波管测量中的应用

提出了一种利用矢量水听器在声管中实现一体化有源吸声终端的方法。该吸声终端采用矢量水听器作为传感元件,以实现入射波和反射波的分离,克服了传统双水听器声波分离方法中传感器间距及测量频率的限制,显著拓宽了一体化有源吸声终端的低频吸声频段。由声管中水声材料的测试原理出发,重点分析了吸声终端中传感元件灵敏度误差对吸声终端性能的影响,并给出了反射、透射系数的修正方法。实验结果表明:该有源吸声终端在100~2000 Hz频段内吸声系数可以达到0.98以上,测量得到材料的声压反射系数、声压透射系数及理论计算基本一致。      

金属橡胶材料吸声特性研究

理论及实验研究了金属橡胶材料吸声性能参数.由金属橡胶材料声学特性参数理论计算式,推导出金属橡胶材料吸声性能参数──声阻抗率和吸声系数的理论计算公式.实验研究了金属橡胶材料结构常数和压缩模量,并建立了结构常数、压缩模量与材料结构参数的关系式,结果表明:相同平均孔隙直径金属橡胶材料具有相同的结构常数值;在一般频率范围内,相同结构参数金属橡胶材料压缩模量近似为常量.通过金属橡胶材料吸声系数的实验测量和理论计算,理论结果与实验结果符合较好,验证了理论和实验研究方法的正确性.     

声学覆盖层吸声系数的多通道逆滤波测量

提出了一种利用最小二乘求逆计算的声学覆盖层吸声系数多通道逆滤波测量方法.该方法通过估计电路信道及水声信道的信道响应,利用最小二乘实现多通道逆滤波算法,通过多路逆信号的同步发射在声学覆盖层处实现高分辨率主瓣、低旁瓣和时域窄脉宽的入射波聚焦,从而提高声学覆盖层低频吸声系数的测量精度。仿真验证了该方法在混响抑制和空时聚焦中的效果.在压力水罐中进行了频率为0.8~5 kHz条件下的钢板试样反射系数和透射系数的测量实验,通过与理论计算值对比,验证了该测量方法的有效性。论文提出的方法适用于非自由场环境下声学覆盖层吸声系数的测量,尤其适用于低频条件下吸声系数的测量。      

释压法混合吸声系统中多孔材料厚度优化研究

研究释压法主被动混合吸声结构吸声性能与多孔吸声材料参数的关系,利用释压法对材料厚度敏感的特性,选择合适的多孔材料厚度提高系统的低频吸声性能。提出一种释压法主被动混合双层吸声结构,将误差传声器置入两层吸声结构之间的空气层中,分别优化各层的厚度,在较宽频带内获得较好吸声。对流阻系数为15000NSm^-4的一类典型的玻璃棉数值仿真,发现选择优化厚度分别为2.8 cm和6 cm,中间空腔长为2 cm,可使有效吸声频带向下大幅扩展。实验结果验证了所提宽带吸声结构。     

Optimization of locally resonant acoustic metamaterials on underwater sound absorption characteristics

The study of acoustic metamaterials, also known as locally resonant sonic materials, has recently focused on the topic of underwater sound absorption. The high absorption occurs only within a narrow frequency band around the locally resonant frequency. Nevertheless, this problem can be addressed through a combination of several acoustic metamaterial layers that have different resonant frequencies. In this paper, an optimization scheme, a genetic and a general nonlinear constrained algorithm, is utilized to enhance the low-frequency underwater sound absorption of an acoustic metamaterial slab with several layers. Both the physical and structural parameters of the acoustic metamaterial slab are optimized to enlarge the absorption band. In addition, the sound absorption mechanism of the acoustic metamaterial slab is also analyzed. The result shows that each layer is found to oscillate as a nearly independent unit at its corresponding resonant frequency. The theoretical and experimental results both demonstrate that the optimized metamaterial slab can achieve a broadband (800–2500 Hz) absorption of underwater sound, which is a helpful guidance on the design of anechoic coatings.     

A model comparison of the absorption coefficient of a Microperforated Insertion Unit in the frequency and time domains

The absorption coefficient of acoustic materials can be measured either in the frequency or the time domain. At normal incidence, a sample of the material is fitted within an impedance tube and the absorption coefficient is calculated in the frequency domain from the measurement of the transfer function between two microphones [ISO 10534-2. Acoustics - determination of sound absorption coefficient and impedance in impedance tubes - Part 2: transfer function method. ISO, Geneva, Switzerland; 1996]. When the acoustic material must be characterized at oblique incidence or in situ (noise barriers, for instance) the absorption coefficient is calculated from measurements of the loudspeaker-microphone impulse response in the time domain, both in free field and in front of the sample [CEN/TS 1793-5. Road traffic noise reduction devices - test method for determining the acoustic performance - Part 5: intrinsic characteristics - in situ values of sound reflection and airborne sound insulation. CEN, Brussels, Belgium; 2003, ISO 13472-1. Acoustic measurement of sound absorption properties of road surfaces in situ - Part I: extended surface method. ISO, Geneva, Switzerland; 2002]. Since the absorption is an intrinsic property of the acoustic material, its measurement in either domain must provide the same result. However, this has not been formally demonstrated yet. The aim of this paper is to carry out a comparison between the absorption coefficient predicted by the impedance model of a Microperforated Insertion Unit and the absorption coefficient predicted from a simulated reflection trace taken into account the finite length of the time window.     

经典局域共振型水声超材料的吸隔声性能研究*

基于水声超材料吸声机理和多层平行介质平面波理论,建立局域共振型水声超材料结构,通过COMSOL进行建模计算,研究该结构的吸声性能机理,此外为了验证钢背衬的隔声性能,在该水声超材料结构基础上添加一层0.005m厚的钢背衬进行仿真对比。研究结果表明,在频段为200Hz-4000Hz时,水声超材料声学性能较好,吸声性能整体较优,且添加钢背衬的水声超材料隔声性能较优,甚至在某频率点达到15dB的隔声差值;此外通过位移场图进一步揭示水声超材料的吸声机理,发现水声超材料结构的位移场和钢背衬都对吸声性能会产生影响,钢背衬通过影响共振吸收来影响吸声性能,而位移场则通过位移幅度大小影响吸声性能。     

基于声学超材料的低频可调吸收器

在当今社会,噪声污染已经成为人类健康的一大威胁,如何有效地控制和消除噪声污染一直是科研领域的一个重要话题.本文以开口环嵌套结构为模型,设计并制备了一种声学超材料.通过理论分析、数值模拟和实验测试,发现由于模型内部空腔的强烈耦合共振效应,该超材料可以在低频区域实现接近完美的吸声效应.此外,通过简单地绕轴旋转其内腔开口方向,即可改变该超材料的相对阻抗值,进而在较宽的频带范围内实现对吸收峰位置的可调控制.由于该超材料具有深亚波长的尺寸,因此非常有利于低频吸声器件的小型化和集成化,同时该模型也为宽带吸收器的设计奠定了基础.     

Messung des absorptionsgrades einer nach dem ‘Perlschnurprinzip’ aufgebauten Wandverkleidung eines reflexionsarmen Raumes

In an anechoic chamber, where the walls are covered with sound-absorbing cubes arranged in pyramids, the distribution of sound pressure around a circle with a non-directional sound source at its centre, was recorded. From these records the variance of the sound pressure distribution was computed and the absorption coefficient determined as a function of frequency. Measurements were made at different points in the room at frequencies ranging from 70 to 4000 Hz.Several possible ways of evaluating the records are presented. The results and applicability of this method are discussed. The results obtained show lower values of absorption coefficient below 200 Hz than coefficients determined with the aid of an interference tube.     

微穿孔介电弹性体薄膜的吸声性能试验分析*

针对普通薄膜型降噪结构的吸声性能较差和吸声带宽较窄的问题,本文设计了一种微穿孔的介电弹性体薄膜吸声结构。该结构由穿孔的介电弹性体薄膜与背腔组合而成,目的是拓宽介电弹性体薄膜低频率段的吸声带宽。针对微穿孔的介电弹性体薄膜吸声结构,从试验角度分析穿孔薄膜初始厚度、穿孔孔径及穿孔间距对结构吸声性能的影响。分析结果可知：通过适当增加薄膜的初始厚度,薄膜的整体吸声性能得到有效提升,最大可将319Hz吸声频带的吸声系数从0.2提升至0.7;减小薄膜的穿孔孔径能够有效拓宽穿孔薄膜的吸声频带,可使吸声系数0.4以上的吸声带宽由304Hz拓宽至432Hz;适当控制穿孔间距能够达到更好的吸声效果。     

Investigation studies involving sound absorbing parameters of roadside screen panels subjected to aging in simulated conditions

The paper presents the results of investigation studies involving the impact of atmospheric factors on sound-absorbing parameters of roadside acoustic screen panels. The research studies comprised the aging test consisting of 1000 cycles in simulated conditions, sound absorption measurements and surface morphology tests, using the SEM scanning method. The simulation of aging consisted of 100 or 150 cycles at a time. Then, the panels were investigated in the reverberation chamber to define their sound-absorbing properties. The process was repeated until 1000 cycles were completed. Basing on the carried out tests, a statistical linear model was worked out which was used to estimate the value of a single number sound absorption coefficient after successive aging cycles. The optimality of the model was demonstrated by means of a statistical test confirming normal distribution of random residuals. For the research studies, we employed an innovative structural design of panels for which aging characteristics were obtained. Basing on the obtained results and on the statistical analysis, the prospects to maintain acoustic properties of the panels during their service life was estimated.