基于微孔板与折曲通道的亚波长宽带吸声结构设计

本文设计了一种由微穿孔板与折曲通道组成的亚波长宽带复合吸声结构,对该复合吸声器低频宽带吸声机理进行了详细分析,建立了该复合吸声结构的理论吸声解析模型与有限元数值分析模型,完成了吸声理论解和数值解的相互验证.该吸声结构在整体厚度为60 mm时,理论上实现了在200—500 Hz频段内平均吸声系数达0.8的低频高效吸声.同时在整体厚度为90 mm时,理论上实现了180—350 Hz频段内多处峰值达0.95的准完美吸声.该复合吸声结构在低频噪声控制工程中具有一定的应用前景.     

吸声型薄膜声学超材料低频宽带吸声性能研究*

本文根据吸声型薄膜声学超材料的吸声机理，在传统的吸声型薄膜声学超材料结构的基础上引入质量非对称结构， 优化了不同厚度质量片的排布方式，并根据优化结果制备了能够实现低频宽带吸声效果的薄膜声学超材料样品。对其进行声学实验的测试结果显示，样品在 100-1000Hz 频率范围内的平均吸声系数达 0.25，并在 250-800Hz 频率范围内出现了多个共振吸收峰，且实验测得的吸声系数曲线与仿真曲线的趋势有较高的一致性。因此该样品实现了低频宽带吸声。     

微穿孔蜂窝-波纹复合声学超材料吸声行为

民用及国防工业领域对工程材料结构提出了更高的应用需求.单一材料结构越来越难以满足实际应用需求,通过人工复合结构实现超常单一及多物理性能的超材料设计已经成为材料结构应用的重要发展方向.本文基于传统的蜂窝夹层结构,在其内部引入波纹结构,并在面板和波纹上分别进行微穿孔形成微穿孔蜂窝-波纹复合声学超材料,在其优异力学承载基础上,实现了低频段的宽频有效吸声降噪.应用微穿孔板吸声理论和声阻抗串并联理论,建立了微穿孔蜂窝-波纹复合声学超材料的吸声理论模型;发展了考虑黏热效应的声传播有限元模型,通过数值模拟验证了理论模型的准确性,并数值计算了声波在超材料微结构内的黏热能量耗散分布,发现超材料能量耗散主要集中于微穿孔处的黏性边界层;进一步开展了超材料吸声参数和尺度设计参数的分析讨论,阐明了不同尺度设计参数对超材料吸声性能的影响规律.本文工作对兼具力学承载与吸声降噪的新型材料结构设计有重要的理论指导价值.     

对称折叠通道结构的低频通风吸声体*

为了消除或减少低频噪声,该文 提出了一种低频通风超材料吸声体,该吸声体由对称的折叠通道结构组成,具有深度亚波长、高通风空间占比和低频高效吸声的特性.通过传递矩阵方法、有限元模拟和四麦克风实验法,揭示了对称折叠通道结构通风吸声的物理机制.首先在理论上分析单个吸声体的通风吸声性能并进行了仿真模拟,在共振频率423 Hz附近,吸声系数大于0.9,通风空间占比高达40%.吸声单体的共振频率可通过改变折叠通道的长度来灵活调控,组合多个不同共振频率的吸声单体可以拓宽吸声体的有效吸声带宽.由四个吸声单体组合的通风吸声体可实现314－366 Hz频率范围内的高效声吸收(吸声系数大于0.8),且通风空间占比达到35%,而结构厚度仅为314 Hz时波长的1/10.该低频通风吸声体具有结构简单、结构强度高和容易制造等特点,在低频通风降噪领域有着潜在的应用前景．     

微穿孔板复合板型声学超材料的低频吸声

针对单层微穿孔板的低频吸声问题提出了微穿孔板复合板型声学超材料结构。将板型声学超材料置入微穿孔板结构的背腔内部实现结构复合。实验结果表明:在相同背腔厚度下,复合结构的吸声性能整体优于单层微穿孔板结构,其中复合结构的吸声曲线从396~892 Hz均大于0.6,在453 Hz处吸声系数达到0.972。利用有限元方法对复合结构进行了仿真,仿真计算的吸声曲线与实验吸声曲线的趋势基本相同,同时发现低频吸声主要由板型声学超材料与声波相互作用贡献。板型声学超材料的吸声峰值的对应频率处,其等效动态质量密度从正变负。在复合结构内部的微穿孔板和板型声学超材料存在相互耦合作用,使得复合结构的第一峰值发生微小偏移。增加板型声学超材料的质量块重量可以使第一吸声峰值向低频移动;保持总背腔厚度不变,增加板型声学超材料的子腔厚度,也可以使第一吸声峰向低频移动。      

宽带透射吸收极化无关超材料吸波体

提出了一种新的基于磁性吸波体材料的具有低频透射和高频宽带吸收特性的超材料吸波体.该超材料吸波体在1 GHz的透射系数为-0.5 dB,具有较好的低频透射特性,可以实现对低频信号的相互通信;在频率大于8.4 GHz的频段,吸收率均大于80%,基本覆盖整个X波段和Ku波段,实现高频宽带吸收.此外,由于该超材料吸波体的单元金属周期结构具有较好的四重旋转对称性,因而是极化无关的.该透射吸收超材料吸波体设计简单,实用性强,具有较强的潜在应用价值.     

一种含圆柱形谐振散射体的黏弹材料低频吸声机理研究

利用层多重散射法分析了一种含圆柱形谐振散射体黏弹 材料吸声层在钢背衬条件下的低频吸声特性. 该吸声层由包覆软材料的圆柱空腔周期嵌入橡胶材料中构成, 其中, 散射体轴线与吸声层平行. 结果表明, 20 mm厚吸声层在1000–3000 Hz具有良好的吸声性能. 通过综合分析单个散射体的吸收截面、单层周期散射体的声吸收、 结构内部位移场以及耗散功率密度分布, 揭示了该吸声层的低频吸声机理. 关键词： 水声吸声 吸收截面 耗散功率密度     

基于非对称吸声器的发动机声学超表面声衬

为了解决发动机低频噪声问题,基于双端口非对称吸声器原理,设计了一种尺寸渐变的吸声超表面,用于发动机声衬降噪设计.首先,建立了非对称共振吸声器的理论分析模型和仿真分析模型,揭示了降噪机理,并分析了其降噪效果的影响因素.然后基于非对称共振吸声器设计了一种声学超表面声衬,用全模型理论计算、等效阻抗理论计算和COMSOL有限元仿真三种方法深入分析了声衬的降噪效果,并用全模型理论计算和等效阻抗理论计算方法考虑了流速对降噪效果的影响,然后对此结构进行了参数优化.研究结果表明,所设计的基于非对称吸声器的声学超表面声衬在厚度仅为2.5 cm (仅为252 Hz对应波长的1/54)的情况下,可实现252—692 Hz的频带范围内3 dB以上的降噪效果,为发动机降噪设计提供了一种新的设计思路.     

超材料谐振子间的电耦合谐振理论与实验研究

通过将两个金属开口环谐振器口对口地放置, 实现了超材料谐振子间的电耦合谐振. 对电耦合谐振的微波等效电路进行了理论分析和数值计算, 结果表明耦合后的超材料谐振子能产生两个谐振频率, 其中一个随耦合强度的增加逐渐向低频方向移动, 而另一个固定在单谐振子的谐振频率处不变. 微波透射谱的实验测试和电磁仿真结果表明, 两个谐振峰随耦合强度的增加分别向低频和高频方向移动. 分析表明: 低频谐振峰的位置主要是由超材料谐振子间的电耦合强度决定的; 高频谐振偏离单谐振子的谐振频率主要是由不可避免的磁耦合引起的, 而且在耦合间距越小时磁耦合影响越大. 提出的基于超材料谐振子间的电磁耦合实现的双频谐振及其可调性极大地增加了超材料的设计与应用空间.     

经典局域共振型水声超材料的吸隔声性能研究*

基于水声超材料吸声机理和多层平行介质平面波理论,建立局域共振型水声超材料结构,通过COMSOL进行建模计算,研究该结构的吸声性能机理,此外为了验证钢背衬的隔声性能,在该水声超材料结构基础上添加一层0.005m厚的钢背衬进行仿真对比。研究结果表明,在频段为200Hz-4000Hz时,水声超材料声学性能较好,吸声性能整体较优,且添加钢背衬的水声超材料隔声性能较优,甚至在某频率点达到15dB的隔声差值;此外通过位移场图进一步揭示水声超材料的吸声机理,发现水声超材料结构的位移场和钢背衬都对吸声性能会产生影响,钢背衬通过影响共振吸收来影响吸声性能,而位移场则通过位移幅度大小影响吸声性能。     

Optimization of locally resonant acoustic metamaterials on underwater sound absorption characteristics

The study of acoustic metamaterials, also known as locally resonant sonic materials, has recently focused on the topic of underwater sound absorption. The high absorption occurs only within a narrow frequency band around the locally resonant frequency. Nevertheless, this problem can be addressed through a combination of several acoustic metamaterial layers that have different resonant frequencies. In this paper, an optimization scheme, a genetic and a general nonlinear constrained algorithm, is utilized to enhance the low-frequency underwater sound absorption of an acoustic metamaterial slab with several layers. Both the physical and structural parameters of the acoustic metamaterial slab are optimized to enlarge the absorption band. In addition, the sound absorption mechanism of the acoustic metamaterial slab is also analyzed. The result shows that each layer is found to oscillate as a nearly independent unit at its corresponding resonant frequency. The theoretical and experimental results both demonstrate that the optimized metamaterial slab can achieve a broadband (800–2500 Hz) absorption of underwater sound, which is a helpful guidance on the design of anechoic coatings.     

Acoustic absorbers at low frequency based on split-tube metamaterials

The remarkable properties of acoustic metamaterials have attracted massive researches and applications, especially on low-frequency sound absorptions. Currently, most of the acoustic metamaterial absorbers employ resonances in plastic cavities, and their structural strengths are important in many circumstances, especially in harsh environment. However, studies of metamaterials including this point are very scarce. Here, we propose an acoustic metamaterial for low-frequency (<500 Hz) absorptions, composed of three nested square split tubes with inverted opening directions. The efficiency of the absorber is investigated both numerically and experimentally, and absorptions at the peeks are found to exceed 90% and the frequency can be effectively adjusted by tuning its geometric parameters. We further test its yield strength under compression and confirm its buckling behavior happens from the outmost layer. This tunable acoustic metamaterial with a fairly good mechanical strength may lead to broad applications in noise reduction.     

Temperature-controlled tunable acoustic metamaterial with active band gap and negative bulk modulus

The local resonant band gap and the negative bulk modulus of the acoustic metamaterial with Helmholtz resonators are strongly affected by the temperature of water. In this paper, the acoustic transmission line method (ATLM) is introduced to investigate the influences of the temperature of water on the local resonant band gap and the negative bulk modulus of the acoustic metamaterial. Results show that the relative variations of the local resonant band gap and the negative effective bulk modulus suffering from the change of the temperature of water are approximately equivalent and are up to about 11%. The reason is that the local resonant frequency is proportional to the sound speed of fluid which is strongly effects by the temperature of water. By achieving the unambiguous relationships between these unusual properties of the acoustic metamaterial and the temperature of water, we find that the temperature-controlled acoustic metamaterial with the active band gap and the active negative bulk modulus can be realized in theory. This idea opens a new avenue for the design of the tunable acoustic metamaterial that can modulate the acoustic wave propagation.     

声学超材料与超表面研究进展

声学超材料是一种人工设计结构的材料,具有超越自然界材料行为的特性,如负折射、反常多普勒效应、平面聚焦等.本文主要介绍了声学超材料近二十年来的相关研究进展,重点论述了超原子声学超材料、超分子声学超材料、超原子簇和超分子簇声学超材料.最后简要介绍了近五年来声学超表面的研究概况和发展趋势.     

Acoustical properties of double porosity granular materials

Granular materials have been conventionally used for acoustic treatment due to their sound absorptive and sound insulating properties. An emerging field is the study of the acoustical properties of multiscale porous materials. An example of these is a granular material in which the particles are porous. In this paper, analytical and hybrid analytical-numerical models describing the acoustical properties of these materials are introduced. Image processing techniques have been employed to estimate characteristic dimensions of the materials. The model predictions are compared with measurements on expanded perlite and activated carbon showing satisfactory agreement. It is concluded that a double porosity granular material exhibits greater low-frequency sound absorption at reduced weight compared to a solid-grain granular material with similar mesoscopic characteristics.     

Wide bandwidth acoustic transmission via coiled-up metamaterial with impedance matching layers

Many acoustic metamaterials suffer from a narrow bandwidth transmission because of the impedance mismatch at the airmetamaterial interface. In this paper, a two-dimensional impedance-matched metamaterial with broadband transmission performance is investigated. The impedance matching layer is introduced for a gradient variation of effective impedance from the inlet of the unit to the outlet. The effective medium theory and corresponding effective model are used to explain the underlying mechanism. The improved energy transmission of our designs is demonstrated by experiment and numerical simulation within a broad frequency bandwidth over 6 kHz. Our impedance-matched design can be used to enhance sound absorption, which is expected to present improved acoustic performance in the applications of acoustic damper and muffler.     

基于石墨烯互补超表面的可调谐太赫兹吸波体

通过在石墨烯超表面设计周期性切条,实现了基于石墨烯互补超表面的可调谐太赫兹吸波体.通过改变外加电压来改变石墨烯的费米能级,吸波体实现频率可调谐特性.研究了石墨烯费米能级、结构尺寸对超材料吸波体吸收特性的影响,并利用多重反射理论研究了其物理机理并且证明了模拟方法的可行性.研究结果表明:当石墨烯费米能级取0.6 eV,基底厚度13μm,石墨烯上切条长宽分别为2.9μm,0.1μm时,吸波体在1.865 THz可以实现99.9%的完美吸收;石墨烯费米能级从0.4 eV增大到0.9 eV,吸波体共振频率从1.596 THz蓝移到2.168 THz,且伴随共振吸收率的改变,吸收率在0.6 eV时达到最大;通过改变费米能级实现的最大吸收率调制度达84.55%.