Application of the ISO 13472-1 in situ technique for measuring the acoustic absorption coefficient of grass and artificial turf surfaces

This paper presents the applicability of an in situ technique based on ISO 13472-1 standard for measuring the acoustic absorption coefficient of grass and artificial turf surfaces for normal incidence from a sound source. The in situ method is based on acoustic impulse response measurement of the material surface. A maximum length sequence (MLS) signal is played through a loudspeaker and the acoustic response from the surface is recorded using a single microphone. The fast Hadamard transform and fast Fourier transform based digital signal post-processing algorithm provides the acoustic absorption coefficient of the surface under test. The normal incidence acoustic absorption coefficient of a commercial artificial quash surface of Dow Co. obtained from this method was compared with the results from the ASTM E1050 impedance tube method for the same surface. The acoustic absorption coefficients of a test-site grass surfaces were measured for 30 mm and 100 mm length of grass blades in wet and dry soil conditions. Substantial difference in the acoustic absorption coefficient was observed for a similar grass-like artificial surface used for estimating sound power of commercial garden equipments and lawnmowers. The advantage of the in situ method lies in its ability to measure the normal incident acoustic absorption coefficient of any planar surface as installed or in situ. Additionally a quick testing time of less than a minute with the use of a laptop sound card based inexpensive data acquisition system is the main feature of this robust method.     

In situ measurements of surface impedance and absorption coefficients of porous materials using two microphones and ambient noise

An in situ measurement method is proposed for obtaining the normal surface impedance and absorption coefficient of porous materials using two microphones located close to the material without a specific sound source such as a loudspeaker. Ambient environmental noise that does not excite distinct modes in the sound field is employed as the sound source. Measurements of the normal surface impedance of glass wool and rockwool have been made using this method in various sound fields. The repeatability and wide applicability of the method are demonstrated by comparing results of measurements in one room with different noise conditions and in three other environments (corridor, cafeteria and terrace). The assumed diffuse nature of the sound field on the material is validated by using absorption characteristics obtained experimentally at oblique incidence. This method allows simple and efficient in situ measurements of absorption characteristics of materials in a diffuse field.     

基于声压-质点速度声强探头的材料吸声系数的测量

通过由一个声压换能器和一个质点速度换能器所构成的传感器(p-u声强探头)同时测量材料表面附近的声压和质点振动速度,可直接得到其声学阻抗,进而得到材料的反射因子、吸声系数。本文利用一个p-u探头声强测量系统,在半消声室内测量了三聚氰胺泡沫的吸声系数,分析了声源高度和入射角度、材料样本尺寸和厚度对吸声系数测量的影响,并和阻抗管中测量得到的法向吸声系数进行了对比。最后分析了声阻抗率的幅值和相位误差对吸声系数的影响,推导了它们的误差传递公式。     

Estimation of pressure-particle velocity impedance measurement uncertainty using the Monte Carlo method

The pressure-particle velocity (PU) impedance measurement technique is an experimental method used to measure the surface impedance and the absorption coefficient of acoustic samples in situ or under free-field conditions. In this paper, the measurement uncertainty of the the absorption coefficient determined using the PU technique is explored applying the Monte Carlo method. It is shown that because of the uncertainty, it is particularly difficult to measure samples with low absorption and that difficulties associated with the localization of the acoustic centers of the sound source and the PU sensor affect the quality of the measurement roughly to the same extent as the errors in the transfer function between pressure and particle velocity do.     

多阶声模态分解的改进阻抗管法测量材料的高频吸声系数

为了测量高频材料吸声系数,采用声模态分解的方法,基于阻抗管构建测试设备,在阻抗管内测量超过平面波截止频率的的高频吸声系数.测量过程中,通过在阻抗管的周向和轴向分别布置传声器阵列,分离管道内前3阶周向声模态以及各阶声模态的轴向传播入射波和反射波,从而得到最高频率达10000 Hz的材料吸声系数,并通过对比常规阻抗管测试方...     

A simple empirical model of polyester fibre materials for acoustical applications

A new empirical model has been developed by the authors to predict the flow resistivity, acoustic impedance and sound absorption coefficient of polyester fibre materials. The parameters of the model have been adjusted to best fit the values of airflow resistivity and sound absorption coefficient measured over a set of 38 samples. Calculated results are compared with normal incidence measurements carried out using two different techniques: the transfer-function method in an impedance tube (ISO 10534-2) and the free-field impulse response method (ISO 13472-1). Measurements performed on polyester fibre materials with different density and thickness values, and diameter ranging from 18 to 48 μm, are in good agreement with the predictions of the new model. It is concluded that the new model can predict the basic acoustic properties of common polyester fibre materials with any practical combination of thickness and density².     

Measurement of sound absorption by underwater acoustic material using pulse-separation method

An alternative pulse-separation method is presented for measuring the sound absorption at normal incidence of an underwater acoustic material in a water-filled impedance tube. A damped sine pulse was generated in the water-filled impedance tube with a regular waveform and a short duration time of approximately 1 ms. During the generation of the pulse, the inverse filter principle was used to compensate for the transducer response. In addition, the effects of the characteristics of the tube termination can be eliminated during the generation of the pulse to obtain a single plane pulse wave in the impedance tube, which is a necessary condition for this technique. Measurements of the sound absorption coefficient of the rubber material and the reflection coefficient from a water/air interface were used to verify the pulse-separation method.     

Measuring the sound absorption properties of noise barriers with inverse filtered maximum length sequences

Loudspeaker characteristics can have an appreciable influence on the sound absorption properties obtained with CEN/TS 1793-5 [1]. Although sound sources with omnidirectional radiation properties are favored, these often hold the problem of long impulse responses due to their design potentially incorporating ports [2]. In this paper, the inverse filtering approach is applied to two different sound sources. It is shown that it is a valuable measure to reduce the influence of the loudspeaker characteristics on the obtained sound absorption values.Furthermore, an attempt is made to measure the absorption properties according to CEN/TS 1793-5 without the need for the subtraction procedure of a free-field measurement. Thereby, as long as only high frequencies are considered, reasonable values can be obtained.     

水下材料吸隔声性能测试近场长脉冲传递函数法

为消除有限空间壁面反射对大样水下材料声学性能测试的影响,利用传递函数法和脉冲法测试原理,建立声波垂直入射情况下水下材料吸隔声性能测试近场长脉冲传递函数法,10mm均匀钢板模型声学性能试验表明,压力环境下钢板反射及隔声性能测试值与理论值基本一致,反射系数测试偏差小于0.1,隔声量测试偏差小于1dB,可以采用近场长脉冲传递函数法测量声波垂直入射情况下材料声学性能,可有效克服边界反射对测试的影响。     

Applications of the causality condition to one-dimensional acoustic reflection problems.

The causality condition is examined as a means of determining frequency-domain information about a submerged object from a partial knowledge of its acoustic reflection characteristics. A one-dimensional problem is considered in which an acoustic wave reflects from an object that is described by the impedance it presents to the fluid. Two new applications of the causality condition to the frequency-domain analysis of this problem are investigated and illustrated by numerical examples. In each application, the causality condition is used to find the object's complex impedance from a knowledge of the reflected wave's magnitude. The first application is to experimental studies where one desires a knowledge of an object's complex impedance but practical limitations only allow a measurement of the reflected wave amplitude. Analysis shows that the causality condition may be used to determine the phase of the reflected wave, and hence the object's impedance, if the reflection coefficient is minimum phase. When this is true, examples suggest that the phase of the reflection coefficient may be accurately determined from the causality condition even in the presence of noise and band-limited data. The second application is to design situations, where one wishes to create an object that reflects sound with a specified frequency-dependent magnitude. The causality condition may aid the designer by providing a knowledge of all causal object impedances that produce the same reflection coefficient magnitude. A numerical example is presented in which a variety of causal object impedances produce the same reflection coefficient magnitude over an infinite frequency range.     

基于声场重建的材料吸声系数测量方法

针对现有方法对材料吸声系数进行现场测量时存在低频测量误差大的问题,本文提出了一种利用扬声器线阵列对材料吸声系数进行现场测量的新方法。该方法使用基于能量比值约束的最小二乘法在待测材料表面进行平面波声场重建并结合双传声器传递函数法对材料的吸声系数进行测量。数值仿真表明在100～1600 Hz频率范围内,新方法在未加约束时能够对材料的吸声系数进行准确测量。在半消声室中利用新方法测量了三聚氰胺泡沫的吸声系数,分析了能量比值约束值对测量结果的影响,并和阻抗管以及其它两种现场测量方法的测量结果进行了对比。结果表明该方法能够对吸声材料在160～1600 Hz频段内的吸声系数进行准确测量,并且相较于现存的现场测量方法,新方法具有更低的测量频率下限。     

Evaluation of sound absorption capacity of asphalt mixtures

Noise generation is an environmental problem that affects human beings, animals and even plants. Several serious diseases have their development associated to the exposure of human beings to high levels of noise pressure, such as arterial hypertension, gastrointestinal changes, alterations in blood glucose and high heart rate, among others. Vehicle traffic is part of a group of noise-generating factors. Various mechanisms govern the generation and propagation of vehicle noises, which are produced mainly by motor vibration at speeds below 50 km/h and by the tire-pavement contact at speeds above 50 km/h. The noise generated by tire-pavement contact is the result of two components: aerodynamic noise (mainly related to the coating porosity), and mechanical noise (related to the coating texture). The noise generation according to these two components may be mitigated by using special asphalt mixtures. This work evaluates the sound absorption of four different types of asphalt mixtures (common dense-graded asphalt mixture, dense-graded rubberized asphalt mixture, rubberized porous coat with void volumes varying from 22% to 27%, and rubberized open-graded friction course) and the effect of granulometry and void volume of each mixture on the sound absorption coefficient. Mixture slabs were molded in a slab compactor developed by LCPC (Laboratoire Central des Ponts et Chaussées) and specimens were extracted from each one for assessing the sound absorption capacity in the laboratory. The acoustic behavior was evaluated according to standard ISO 10534-2, using impedance tubes. Results showed that sound absorption is strongly influenced by void percentage, interconnected void percentage and layer thickness.     

Modal decomposition method for acoustic impedance testing in square ducts

Accurate duct acoustic propagation models are required to predict and reduce aircraft engine noise. These models ultimately rely on measurements of the acoustic impedance to characterize candidate engine nacelle liners. This research effort increases the frequency range of normal-incidence acoustic impedance testing in square ducts by extending the standard two-microphone method (TMM), which is limited to plane wave propagation, to include higher-order modes. The modal decomposition method (MDM) presented includes four normal modes in the model of the sound field, thus increasing the bandwidth from 6.7 to 13.5 kHz for a 25.4 mm square waveguide. The MDM characterizes the test specimen for normal- and oblique-incident acoustic impedance and mode scattering coefficients. The MDM is first formulated and then applied to the measurement of the reflection coefficient matrix for a ceramic tubular specimen. The experimental results are consistent with results from the TMM for the same specimen to within the 95% confidence intervals for the TMM. The MDM results show a series of resonances for the ceramic tubular material exhibiting a monotonic decrease in the resonant peaks of the acoustic resistance with increasing frequency, resembling a rigidly-terminated viscous tube, and also evidence of mode scattering is visible at the higher frequencies.     

压力罐中水声材料声学特性的参量源测量法

设计了一种原波频率500 kHz、差频范围1~30 kHz的截断宽带参量阵,作为水声材料测量系统的声源。通过分析典型频率下的宽带参量源指向性理论计算和实际测量结果,发现两者结果的曲线基本吻合,证明计算模型是正确的。应用钟形短时脉冲实现水声材料声特性的宽带测量,有益于降低样品边缘衍射干扰。并建立了测量水声材料大面积板状样品声压反射系数、声压透射系数和吸声系数的压力罐测量系统,罐体内尺寸Φ4 m×12 m,最高静水压4.5 MPa,测量频率范围1~30 kHz。对标准样品(尺寸1m×1m)进行了测量实验,其测量结果和理论曲线有很好的吻合,参量源测量法得到了验证;之后,通过对一块橡胶板样品在不同静压力下的吸声性能进行了测量和有效评估,进一步确认了参量源测量法在压力罐这样有限水域中的潜在应用价值。      

吸声型薄膜声学超材料低频宽带吸声性能研究*

本文根据吸声型薄膜声学超材料的吸声机理，在传统的吸声型薄膜声学超材料结构的基础上引入质量非对称结构， 优化了不同厚度质量片的排布方式，并根据优化结果制备了能够实现低频宽带吸声效果的薄膜声学超材料样品。对其进行声学实验的测试结果显示，样品在 100-1000Hz 频率范围内的平均吸声系数达 0.25，并在 250-800Hz 频率范围内出现了多个共振吸收峰，且实验测得的吸声系数曲线与仿真曲线的趋势有较高的一致性。因此该样品实现了低频宽带吸声。     

Research on the sound absorption performance of metal rubber material

The sound absorption performance of Metal Rubber material was studied theoretically and experimentally. The acoustic impedance rate and the sound absorption coefficient were derived based on the acoustic parameters of metal rubber material. The relation of structure constant, compressibility modulus and structural parameters was investigated experimentally. The results showed that the specimen of metal rubber with the same mean porosity diameter had the same structure constant. For the same structural parameters, the compressibility modulus of metal rubber material was approximately constant in certain frequency range. The calculated acoustic parameters are in good agreement with the experimental results, demonstrating the effectiveness of theoretical models.     

Evaluation of the acoustic and non-acoustic properties of sound absorbing materials using a three-microphone impedance tube

This paper presents a straightforward application of an indirect method based on a three-microphone impedance tube setup to determine the non-acoustic properties of a sound absorbing porous material. First, a three-microphone impedance tube technique is used to measure some acoustic properties of the material (i.e., sound absorption coefficient, sound transmission loss, effective density and effective bulk modulus) regarded here as an equivalent fluid. Second, an indirect characterization allows one to extract its non-acoustic properties (i.e., static airflow resistivity, tortuosity, viscous and thermal characteristic lengths) from the measured effective properties and the material open porosity. The procedure is applied to four different sound absorbing materials and results of the characterization are compared with existing direct and inverse methods. Predictions of the acoustic behavior using an equivalent fluid model and the found non-acoustic properties are in good agreement with impedance tube measurements.     

Improving low-frequency sound absorption of micro-perforated panel absorbers by using mechanical impedance plate combined with Helmholtz resonators

The traditional Micro-perforated plate (MPP) is a kind of clean and non-polluting absorption structure in the middle and high frequency and has been widely used in the field of noise control. However, the sound absorption performance is dissatisfied at low frequencies when the air-cavity depth is restricted. In this paper, a mechanical impedance plate (MIP) is introduced into the traditional MPP structure and a Helmholtz resonator is attached to the MIP. Mechanical impedance plate (MIP) provides a good absorption at low frequency by using mechanism of mechanical resonance and the acoustic energy is dissipated in the form of heat with viscoelastic material. Helmholtz resonator can fill in the defect of the poor absorption effect between the Micro-perforated plate (MPP) and the mechanical impedance plate (MIP). The acoustic impedance of the proposed sound absorber is investigated by using acoustic electric analogy method and impedance transfer method. The influence of the tube’s length of Helmholtz resonator and the number of Helmholtz resonator on the sound absorption is studied. The corresponding results are in agreement with the theoretical calculation and prove that the composite structure has the characteristics of improving the low frequency sound absorption property.     

Acoustic properties of micro-perforated panel absorber having arbitrary cross-sectional perforations

Micro-perforated panel absorber is used in many noise control applications as a next-generation absorbing material. Perforation shapes of micro-perforated panel studied are usually circular in the past. However, in practice, the perforations are often non-circular or irregular shape due to manufacturing techniques. Sound absorption coefficient and absorption bandwidth of the micro-perforated panel absorber may be further improved, when the perforations in shape are changed. In view of the existing exact solutions of sound propagation in tubes, the simple formulas of specific acoustic impedances of the tubes for triangle and square cross-sectional perforations are derived. Mass reactance end correction of the micro-perforated panel is obtained based on the sound radiation of a shaped piston. The specific acoustic impedance ratio of the micro-perforated panel absorber is calculated and analyzed, which can predict its sound absorption bandwidth. Finally, for closed perforations, the influences of the perforations in shape (including triangle, circle, square and irregular circle) on sound absorption of the MPP absorber are discussed in collaboration with FE simulations.     

使用脉冲声和矢量传声器的现场测量吸声系数*

使用不同声源利用矢量传声器对毛毡材料进行现场吸声系数测试,研究了不同背景下不同声源的抗噪能力。矢量传声器可以同时测得声压和质点振速信号,进而可计算得到阻抗,利用自由空间和材料表面的阻抗可计算得到材料的吸声系数。在此次试验中,使用不同声源分别在无干扰和有一白噪声干扰源的两种情况下进行测试。结果表明,使用对数扫频脉冲和巴特沃斯脉冲测试所得的吸声系数曲线更平滑,说明脉冲声可以有效降低环境反射的影响,在高噪声背景下使用对数扫频脉冲测试所得的结果基本没有受到背景噪声的影响,说明对数扫频脉冲的抗噪能力更强。因此,使用对数扫频脉冲作为声源进行测试可有效减弱环境反射和背景噪声的影响。