扩芯光纤原理及其在光器件耦合中的应用

介绍了两种可以增大单模光纤模场直径并出射准直平行光束的扩芯光纤(ECF)的原理和制作方法。分析了单模光纤熔接渐变折射率多模光纤法通过改变渐变折射率多模光纤的长度和自聚焦参量实现模场扩大缩小的原理,制作的扩芯光纤模场直径扩大到16．6μm,出射光束平行效果较好,轴向耦合容限比单模光纤扩大了近6倍。加热扩芯光纤则是通过控制加热温度和加热时间直接使单模光纤掺杂物质发生扩散,从而实现扩束和光束准直,模场直径达到15．4μm,横向、轴向耦合容限都比单模光纤有很大提高。因此扩芯光纤可以简化单模光纤的耦合对准过程,用来制作新型的单模光纤或掺铒光纤连接器,也可以用于其它光器件中与单模光纤的准直。     

Optimal direct coupling from single-mode fibers to Ti:LiNbO3, channel waveguides

We investigate the optimal direct coupling from single-mode fibers to Ti:LihbO₃, channel waveguides using a very general formula and a heuristic optimization technique in this article. The coupling efficiency of the optical power depends on both the fiber positions and the modal sizes of the incident fields. From our numerical simulation, it is found that the optimal positions of the fiber axes are not in alignment with the peaks of the waveguiding modal fields and that the coupling efficiency can be improved by microlenses.     

激光点火系统用高功率光纤光开关

 仿真和实验研究了一种控制Nd:YAG脉冲激光能量通断的光纤直接连接型光开关。建立光纤耦合模型,分析了光纤对准误差中对耦合效率的影响,其中横向偏移的影响最显著。采用微机电系统V型槽固定光纤,微小型凸轮作为制动器,步进电机驱动凸轮旋转,微小型凸轮与移动光纤相切,带动光纤移动,实现两光纤的错开和对准。制造了这种高功率直接连接型光纤光开关原理样机,并进行了主要性能测试。测试结果表明,这种光开关能够满足激光点火系统的大容量、高隔离度的要求。     

固体激光器与光纤激光器对光子晶体光纤棒耦合的分析与对比

耦合效率的高低与耦合后光斑的好坏直接影响着光子晶体光纤棒的放大效果,因此需要对种子光的耦合效果进行研究,选择合适的激光器作为种子源。本文对光子晶体光纤棒在固体激光器与光纤激光器两种情况下的耦合效率进行了理论分析;模拟计算了两种激光器情况下耦合效率的变化规律以及对准误差对耦合效率的影响;选择合适的透镜或透镜组,使用两种激光器对光子晶体光纤棒进行了耦合实验;对比两种激光器的耦合效果可知:固体激光器的耦合效率最高只能达到62.4%,而光纤激光器的耦合效率可以达到80%以上;在光纤激光器耦合情况下,对不同功率注入时耦合效率,以及耦合后光斑进行了实验分析。得到的实验结果对后续光纤棒的放大实验具有指导作用。     

纤芯圆对称分布多芯光纤的耦合特性

通过将标准单芯单模光纤与纤芯圆对称分布的多芯光纤的一个纤芯对准熔接后,再在多芯光纤任意位置进行热熔融拉锥,实现多芯光纤光功率的高效耦合注入和光功率在各个纤芯中分布比例的控制,解决了由于多芯光纤结构的特殊性引起的光源光功率难于直接注入的问题。基于光纤耦合模理论建立多芯光纤各纤芯之间的耦合模方程,得到各个纤芯中光功率与耦合长度之间的关系曲线,并与实际耦合实验结果对比,验证该方法可行。研究结果可为多芯光纤光学器件的发展提供潜在的应用价值。     

The impact of the off-axis for the spatial light to multimode fiber coupling system

The electric field distribution of Gaussian beam and properties of Cassegrain optical antenna are discussed and their images have been simulated. By analysis of Cassegrain optical antenna with collimation and off-axis circumstance, laser power distribution and the curve of coupling efficiency are obtained. The question of spatial light to multimode fiber coupling efficiency with alignment and off-axis are researched. At last, taking into account off-axis situation of Cassegrain and laser beam to multimode fiber, the coupling efficiency of the whole system is discussed. These researches are necessary and useful for increasing spatial light to multimode fiber coupling efficiency.     

A novel technique for laser diode to single mode fiber coupling

An optical fiber coupler based on the semi-linear passive phase conjugate mirror is analyzed. The threshold coupling strength is determined from theoretical considerations. An estimate of 50% for the overall coupling efficiency is made, assuming there is good mode matching between the light incident on the fiber and the propagating mode. The coupler exhibits a high degree of alignment insensitivity allowing for simple manufacture.     

Grating coupler efficiency enhancement by double layer interference

A simple method for improving grating couplers' coupling efficiency without any extra microfabrication processes is proposed. This method can improve the coupling efficiency with 1.69 dB by utilizing the combined interference in the cladding layer and air gap between the cladding surface and the paralleled angle polished fiber facet. The proposed method can be applied to various kinds of on-chip grating couplers. Back reflection,1 dB bandwidth, and fiber alignment tolerance have also been improved at the same time.     

电光聚合物波导中的锥形结构

提出并设计了一种基于电光聚合物的锥形波导,可用于单模光纤与电光聚合物波导器件之间的连接.锥形波导中采用了宽度锥形和折射率锥形结构.宽度锥形采用劈形形状,通过宽度和折射率的缓慢变化实现模场转换.劈形形状的宽度锥形具有较小的损耗且易于制作,折射率锥形可采用灰度掩膜光刻技术制作.研究了锥形波导的传输损耗与锥形波导的长度、波导宽度和厚度、材料吸收损耗等参数的关系及其优化,分析了锥形波导中的功率传输、模场分布与模式转换效率.结果显示锥形波导的传输损耗小于0.37 dB,光纤-波导-光纤的连接损耗优于1.62 dB,对插入损耗的改善达到8.78 dB,模场转换效率达到了83.7%.     

Improved design for SOI based evanescently coupled multilayer spot-size converter

We report an improved version of a spot-size converter (SSC) consisting of a silicon nanowire evanescently coupled to a phase-matched Poly-Si multilayer structure. With wider transversal dimensions the multilayer structure expands the mode significantly thus increasing the coupling efficiency with the conventional single-mode fiber. Detailed optimization process of a 17-layer based SSC is discussed and its coupling efficiency with a high-NA fiber of radius 2 μm is obtained as 98% providing only 0.087 dB loss. Vertical alignment tolerance between the optimized SSC and a high-NA fiber of radius 2 μm is also shown. This novel design does not consist of a taper and can be fabricated by using CMOS compatible process. It has a short device length and more relaxed alignment tolerances with the fiber. Full-vectorial and computationally efficient finite element method and the least squares boundary residual method have been used for the analysis and optimization of the proposed structure.     

Pigtailing the high-Q microsphere cavity: a simple fiber coupler for optical whispering-gallery modes

We demonstrate a simple method for efficient coupling of standard single-mode optical fibers to a high- Q optical microsphere cavity. Phase-matched excitation of whispering-gallery modes is provided by an angle-polished fiber tip in which the core-guided wave undergoes total internal reflection. In the experimental setup, which included a microsphere with both an input and an output coupler, the total fiber-to-fiber transmission at resonance reached 23% (total insertion loss, 6.3 dB), with loaded quality factor Q>/=3x10(7) and unloaded Q approximately 1.2x10(8) at 1550 nm. A simple pigtailing method for microspheres permits their wider use in fiber optics and photonics devices.     

980 nm泵浦激光二极管与柱形透镜光纤耦合的角向容忍度

给出了一个计算980 nm泵浦激光二极管与柱形透镜光纤耦合角向容忍度的理论模型,并选择圆形的柱透镜光纤进行数值计算,得出了在水平和垂直方向上偏转加平移时的相对耦合效率及绕光纤轴向转动的相对耦合效率的数值计算结果并加以分析,同时也研究了光纤透镜的形状和激光二极管与光纤的间距对相对耦合效率的影响.     

单模光纤与Ti:LiNbO3单模平面光波导端面激励耦合的研究

本文报导一个单模光纤与单模Ti扩散LiNbO3光波导的端面耦合及固定连接实验研究.利用电弧烧熔法在单模光纤端面上制成了微透镜,改善了模场匹配程度,采用二维硅V形糟,提高了光纤与波导的对准精度。     

基于非球面透镜的空间光场光纤耦合系统研究

针对全光纤激光雷达中空间光场与单模光纤的耦合问题,设计了基于非球面透镜的望远镜光纤耦合系统.利用ZEMAX软件以单模光纤耦合效率为优化目标对其结构参量进行优化设计,然后分别用LED和激光器作为光源进行初步实验,比较直接耦合和非球面透镜耦合效果.实验结果表明,采用非球面透镜耦合可使多模光源的耦合效率比直接耦合增加约47％,与仿真结果45％非常接近,且不同芯径耦合光功率之比大略等于芯径比平方;而该耦合方式可使单模光源的耦合效率增加约20％,且耦合进不同小芯径光纤的耦合效率之比约为其芯径比平方的2.4倍,这对构建全光纤转动喇曼激光雷达系统具有重要意义.     

楔形光纤与半导体多量子阱平面光波光路芯片的耦合分析

采用楔形光纤(WSF)实现了与半导体多量子阱(MQW)平面光波光路(PLC)芯片的高效耦合。在多量子阱-平面光波光路前置模斑转换器(SSC)和不加模斑转换器的情况下,用阶梯串联法(SCM)数值模拟并优化设计了楔形光纤-平面光波光路间最佳耦合参量:楔形光纤楔角45°、端面圆柱透镜曲率半径2.5μm、模斑转换器-多量子阱-平面光波光路出射椭圆光斑长半轴3.5μm、纵横比5、楔形光纤-平面光波光路间垂直方向和水平方向无偏移、纵向间距5.5μm。用反向推演法(IDM)实验分析了楔形光纤样品的出射光场,与阶梯串联法(SCM)计算结果相比长轴误差为3.125%,短轴误差为0.8%。建立楔形光纤-平面光波光路-单模光纤(SMF)的耦合实验系统,在1.55μm波长处以单模光纤作为出纤的相同条件下,发现楔形光纤激励入射平面光波光路比单模光纤和锥形透镜光纤(TLF)作为入纤的耦合效率分别提高了24.827 dB和16.22 dB,为多量子阱-平面光波光路芯片尾纤封装技术提供了实验原型。     

在单模光纤中放大的反斯托克斯拉曼背向自发散射的温度效应

在单模光纤中,输入的激光功率大于阈值时．出现放大的反斯托克斯拉曼背向自发散射现象。实验发现：放大的反斯托克斯拉曼背向自发散射具有温度效应．与反斯托克斯拉曼背向自发散射一样,放大的拉曼散射光的光子通量受到光纤温度的调制。反斯托克斯拉曼背向白发散射的放大效应抑制了单模光纤中的相干噪声,改善了系统的信噪比。实验还发现．放大的反斯托克斯扎曼背向自发散射空域曲线上放大的端点位置随激发功率的增高前移并具有一定的规律性。放大的反斯托克斯拉曼背向自发散射的温度效应作为一种新的测温原理,已应用于远程30km分布光纤温度传感器系统。     

Optical interconnection between different spatial modes using double phase conjugate mirror with polarization alignment system

We propose a fundamental interconnection method using a polarization alignment system for waveguides having different spatial modes. In addition, as an example for the verification of the fundamental operation, we demonstrate an interconnection between a photonic crystal fiber and a laser that have obviously different spatial modes. The polarization alignment system operates synergistically with a self-written waveguide formed with a double phaseconjugate mirror. This technique enables us to interconnect a photonic crystal fiber with a laser source without complicated and time-consuming optical alignment. In this method, although it is not necessary to perform an external control for interconnection, the waveguide most suitable for connection is formed autonomously in a Sn₂P₂S₆:Sb crystal developed for this purpose. There was a marked reduction in the polarization dependence of coupling efficiency, compared with that observed using a stand-alone double phase-conjugate mirror.     

量子点单光子源的光纤耦合

半导体量子点在低温下产生谱线细锐的激子发光可制备单光子源.光纤耦合可避免低温共聚焦装置扫描定位和振动影响,是实现单光子源即插即用和组件化的关键技术.在耦合工艺上,基于微区定位标记发展出拉锥光纤与光子晶体腔或波导侧向耦合、大数值孔径锥形端面光纤与量子点样片垂直耦合等技术;然而,上述工艺需要多维度精密调节以避免柔软光纤的畸形弯曲实现对准和高效耦合.陶瓷插针或石英V槽封装的光纤无弯曲且具有大平滑端面,只要与单量子点样片对准贴合就可保证垂直收光, V槽封装的排式光纤还可通过盲对粘合避免扫描对准,耦合简单.本文在前期排式光纤粘合少对数分布Bragg反射镜(distributed Bragg reflector, DBR)微柱样片实现单光子输出基础上,经理论模拟采用多对数DBR腔提升样片垂直出光和光纤收光效率,使光纤输出单光子计数率大大提升.     

Application of fiber interferometer in coherent Doppler lidar

A novel coherent Doppler lidar (CDL) system based on single-mode fiber (SMF) components and instruments is presented to measure the speed of target. A fiber interferometer used in CDL system is reported.This fiber mixer is employed as a coherent receiver to resolve the shifts of signal-to-noise ratio (SNR) and mixing efficiency induced by backscattered field's wavefront error. For a certain wavelength, the maximum coupling efficiency between signal and SMF is determined by the ratio of pupil diameter to focal length of the coupling lens. The legible interference patterns and spectrum signals show that fiber interferometer is suitable to compensate for amplitude and phase vibrations. This robust coherent receiver can achieve improved CDL system performance with less transmitter power.     

Tapered fused fiber bundle coupler capable of 1 kW laser combining and 300 W laser splitting

A high efficiency 7 × 1 multimode fiber coupler using the method of fusion and tapering is reported. This coupler can be applied to combine laser power, ad it can be used as a 1 × 7 splitter with reversible simultaneously. In the experiment, for combiner, coupling output power of 1032 W is obtained with the input power of 1066 W. The total coupling efficiency is 96.8%. The average insertion loss of each input fiber is 0.14 dB at ∼150 W input power. To splitter, the sum of 7 output ports power is 294 W with the input power of 341 W, and the insertion loss is about 13.8%. This fiber coupler can be applied in pumping all-fiber double clad fiber laser, as well as power combination and splitting of fiber lasers.