超声清洗装置空化噪声谱分析法空化噪声级测量

空化强度是用以衡量液体介质中空化活动的剧烈程度,同时空化效应在超声清洗中起关键作用,因此,测量超声清洗槽中的空化强度便可了解其中空化活动的情况.当发生空化时,液体介质中会产生成分复杂空化噪声,对空化噪声谱进行分析和计算得到空化噪声级,据此可判断空化强度.实验测得结果表明:超声清洗装置内稳态空化分布广泛、均匀,瞬态空化分...     

Measurement of chemical activity of ultrasonic cavitation in aqueous solutions

Decomposition of water by cavitation produces the same free radicals as ionizing radiations. Standard chemical dosimeters have been used to measure the chemical activity of cavitation, and to obtain an indirect determination of the relative yields of the primary products of the sonolysis of water. It is shown that the yields are dependent only upon the energy deposited, and are completely independent of the frequency, intensity or intensity distribution of the ultrasonic field, and also of the gas content of the solution. The cavitation bubbles are found to deposit chemical energy in a manner very similar to that of slow -particles.     

Mechanism and dynamics of hydrodynamic-acoustic cavitation (HAC)

Bubble clusters in hydrodynamic cavitation, acoustic cavitation and hydrodynamic-acoustic cavitation (HAC) are investigated via high-speed photography. By introducing a cavitation state variable, a method for cavitation characterization is proposed. The periodic characteristics and intensity distributions of hydrodynamic cavitation, acoustic cavitation and HAC are quantitatively analyzed using this method. It is found that the range of HAC is evidently widened and the strength of HAC is significantly enhanced compared with hydrodynamic cavitation or acoustic cavitation. Furthermore, we developed a preliminary physical model describing the dynamics of a cavitation bubble in HAC and proposed a mechanism to explain the enhancement of the intensity in HAC.     

Acoustic characterization of cavitation intensity: A review

Cavitation intensity is used to describe the activity of cavitation, and several methods are developed to identify the intensity of cavitation. This work aimed to provide an overview and discussion of the several existing characterization methods for cavitation intensity, three acoustic approaches for charactering cavitation were discussed in detail. It was showed that cavitation noise spectrum is too complex and there are some differences and disputes on the characterization of cavitation intensity by cavitation noise. In this review, we recommended a total cavitation noise intensity estimated via the integration of real cavitation noise spectrum over full frequency domain instead of artificially adding inaccurate filtering processing.     

声-流耦合空化场观测与量化表征探索*

该文利用搭建的高速摄影和空化噪声同步观测的声-流耦合空化实验平台,观察分析了声-流耦合场中空化云的演化规律及相应的空化噪声特征。通过引入空化状态变量,给出了空化强度的一种新的明确表述,并提出了一种基于高速摄影图像分析来测量和表征空化状态变量及空化强度的方法。利用该方法进一步对声-流耦合空化时间演化周期性和空间强度分布进行了定量计算。结果表明,声-流耦合空化强度和作用范围相比单独声空化和单独水力空化有显著的提升。     

超声清洗槽内空化强度的测量

对洗涤槽内超声空化的相对强度及其分布进行了研究。采用铝箔腐蚀法,应用图像、数据处理软件对试验结果进行处理,最后对实验结果进行了讨论。     

Observations of water cavitation intensity under practical ultrasonic cleaning conditions

In the industrial cleaning processes either organic solvents or water solutions are used as the cleaning media. The primary causative factor of ultrasonic cleaning is cavitation. Below are presented results of investigations into the influence of temperature, gas content and the solution level in an ultrasonic cleaner on cavitation intensity in the tap water. Previous investigations have revealed a great deal of information on the influence of the above factors on the cavitation intensity and these are confirmed. It has now been found that the tap water reaches the highest cavitation intensity at temperatures below 20 degrees C but during heating at higher temperatures (20-40 degrees C) a second peak of cavitation intensity may appear-depending on the height of water in the bath and air content.     

弱酸试纸法测量功率超声珩磨空化声场的研究*

为了简便、直观地测量功率超声珩磨磨削区的空化声场强度及分布情况,提出了利用弱酸PH试纸测量磨削区空化声场的方法。利用超声空化效应产生的弱酸空化泡在PH试纸表面溃灭后,形成深浅和分布不同的变色区域,间接地表征油石表面空化声场的强弱和分布规律。通过对比不同超声频率、测试距离和时间,得出了最佳测试距离和时间。结果表明,当超声频率为18.6 kHz,距离为10 mm时,测得油石表面的空化声场强度和分布最佳。该方法可形象地评价功率超声珩磨磨削区空化声场的强度和分布情况,具有一定的实际应用价值。     

Characterization of acoustic cavitation in water and molten aluminum alloy

High-intensive ultrasonic vibrations have been recognized as an attractive tool for refining the grain structure of metals in casting technology. However, the practical application of ultrasonics in this area remains rather limited. One of the reasons is a lack of data needed to optimize the ultrasonic treatment conditions, particularly those concerning characteristics of cavitation zone in molten aluminum.The main aim of the present study was to investigate the intensity and spectral characteristics of cavitation noise generated during radiation of ultrasonic waves into water and molten aluminum alloys, and to establish a measure for evaluating the cavitation intensity. The measurements were performed by using a high temperature cavitometer capable of measuring the level of cavitation noise within five frequency bands from 0.01 to 10 MHz. The effect of cavitation treatment was verified by applying high-intense ultrasonic vibrations to a DC caster to refine the primary silicon grains of a model Al–17Si alloy. It was found that the level of high frequency noise components is the most adequate parameter for evaluating the cavitation intensity. Based on this finding, it was concluded that implosions of cavitation bubbles play a decisive role in refinement of the alloy structure.     

Stabilizing in vitro ultrasound-mediated gene transfection by regulating cavitation

It is well known that acoustic cavitation can facilitate the inward transport of genetic materials across cell membranes (sonoporation). However, partially due to the unstationary behavior of the initiation and leveling of cavitation, the sonoporation effect is usually unstable, especially in low intensity conditions. A system which is able to regulate the cavitation level during sonication by modulating the applied acoustic intensity with a feedback loop is implemented and its effect on in vitro gene transfection is tested. The regulated system provided better time stability and reproducibility of the cavitation levels than the unregulated conditions. Cultured hepatoma cells (BNL) mixed with 10 μg luciferase plasmids are exposed to 1-MHz pulsed ultrasound with or without cavitation regulation, and the gene transfection efficiency and cell viability are subsequently assessed. Experimental results show that for all exposure intensities (low, medium, and high), stable and intensity dependent, although not higher, gene expression could be achieved in the regulated cavitation system than the unregulated conditions. The cavitation regulation system provides a better control of cavitation and its bioeffect which are crucial important for clinical applications of ultrasound-mediated gene transfection.     

Measurement of radical production as a result of cavitation in medical ultrasound fields

This paper describes the use of the terephthalate dosimeter to measure the threshold and extent of cavitation arising from medical ultrasound sources at high frequencies. Significant hydroxyl radical production was noted from a physiotherapy source and low level activity was also detected when using a pulsed, diagnostic type transducer system. The effect of sound intensity and the type of field is described. The possibility of using polymer degradation to monitor the cavitation is also discussed.     

Mapping of cavitational activity in a pilot plant dyeing equipment

A large number of papers of the literature quote dyeing intensification based on the application of ultrasound (US) in the dyeing liquor. Mass transfer mechanisms are described and quantified, nevertheless these experimental results in general refer to small laboratory apparatuses with a capacity of a few hundred millilitres and extremely high volumetric energy intensity. With the strategy of overcoming the scale-up inaccuracy consequent to the technological application of ultrasounds, a dyeing pilot-plant prototype of suitable liquor capacity (about 40 L) and properly simulating several liquor to textile hydraulic relationships was designed by including US transducers with different geometries.Optimal dyeing may be obtained by optimising the distance between transducer and textile material, the liquid height being a non-negligible operating parameter. Hence, mapping the cavitation energy in the machinery is expected to provide basic data on the intensity and distribution of the ultrasonic field in the aqueous liquor. A flat ultrasonic transducer (absorbed electrical power of 600 W), equipped with eight devices emitting at 25 kHz, was mounted horizontally at the equipment bottom.Considering industrial scale dyeing, liquor and textile substrate are reciprocally displaced to achieve a uniform colouration. In this technology a non uniform US field could affect the dyeing evenness to a large extent; hence, mapping the cavitation energy distribution in the machinery is expected to provide fundamental data and define optimal operating conditions. Local values of the cavitation intensity were recorded by using a carefully calibrated Ultrasonic Energy Meter, which is able to measure the power per unit surface generated by the cavitation implosion of bubbles. More than 200 measurements were recorded to define the map at each horizontal plane positioned at a different distance from the US transducer; tap water was heated at the same temperature used for dyeing tests (60 °C). Different liquid flow rates were tested to investigate the effect of the hydrodynamics characterising the equipment.The mapping of the cavitation intensity in the pilot-plant machinery was performed to achieve with the following goals: (a) to evaluate the influence of turbulence on the cavitation intensity, and (b) to determine the optimal distance from the ultrasound device at which a fabric should be positioned, this parameter being a compromise between the cavitation intensity (higher next to the transducer) and the US field uniformity (achieved at some distance from this device).By carrying out dyeing tests of wool fabrics in the prototype unit, consistent results were confirmed by comparison with the mapping of cavitation intensity.     

Luminescence intensity of vortex cavitation in a Venturi tube changing with cavitation number

Hydrodynamic cavitation in a Venturi tube produces luminescence, and the luminescence intensity reaches a maximum at a certain cavitation number, which is defined by upstream pressure, downstream pressure, and vapor pressure. The luminescence intensity of hydrodynamic cavitation can be enhanced by optimizing the downstream pressure at a constant upstream pressure condition. However, the reason why the luminescence intensity increases and then decreases with an increase in the downstream pressure remains unclear. In the present study, to clarify the mechanism of the change in the luminescence intensity with cavitation number, the luminescence produced by the hydrodynamic cavitation in a Venturi tube was measured, and the hydrodynamic cavitation was precisely observed using high-speed photography. The sound velocity in the cavitating flow field, which affects the aggressive intensity of the cavitation, was evaluated. The collapse of vortex cavitation was found to be closely related to the luminescence intensity of the hydrodynamic cavitation. A method to estimate the luminescence intensity of the hydrodynamic cavitation considering the sound velocity was developed, and it was demonstrated that the estimated luminescence intensity agrees well with the measured luminescence intensity.     

高速水流中旋涡空化所引起的空蚀和振动

为了研究旋涡空化所引起的空蚀和振动观象以及二者的关系,采用高速摄影的方法,观察了发生在射流放水阀山部的空化形态。采用快速富里叶变换（FFT）分析了空化所引起的振动。采用失重法,进行了空蚀实验。结果表明,旋涡空化能引起严重的空蚀和剧烈的振动。在旋涡空化发展的个同阶段,其所导致的振动和空蚀呈观了个同的特性。当Sσ>0.74时,随空化数的变化,振动和空蚀呈现了相同的变化趋势,但是,在0.50<σ<0.74的范围内,振动和空蚀呈现了相反的变化趋势。这是由于水流中空化旋涡的数目和形态随空化数的变化,以及旋涡空化引起振动和空蚀的机理不同所造成的。     

The influence of air content in water on ultrasonic cavitation field

Cavitation is a complex physical phenomenon affected by many factors, one of which is the gas dissolved in the medium. Researchers have given some efforts to the influence of gas content on sonoluminescence or some specific chemical reactions in and around the bubble, but limited work has been reported about the influence on the ultrasonic cavitation field distribution. In this work, the intensity distribution of the ultrasound field in a cleaning tank has been measured with the hydrophone. After analysed and visualised by MATLAB software, it was found that the cavitation intensity distribution in degassed water was much better than that in tap water. And further study proved that degassing process can improve the cavitation effect dramatically both in intensity and scope. Finally, the cavitation fields in mediums with different gas content were measured and the specific influence of air content on cavitation field was discussed.     

Experimental investigation on the ultrasonic impregnation of wood through measurements of the intensity of sonoluminescence

Ultrasonic impregnation is thought to be an effective way of permeation of liquid into material through the material-surface reforming with the attack by an ultrasonic cavitation jet or by the shock wave emitted from a collapsing bubble, or through dynamic transformation of material like a sponge. The action of a cavitation bubble can also provide penetration of liquid into the interior of the material. This paper investigates whether there is a correlation between the intensity of sonoluminescence (SL) measured at different positions and the increment in the mass of the wood material (cedar) after sonication with immersion into water in order to clarify the role of cavitation bubbles for ultrasonic impregnation. It was found that a high mass change was obtained for the material located at the position for high (the maximum) SL intensity. The number density of ultrasonic cavitation bubbles that are able to collapse leading to the emission of SL is correlated with the degree of ultrasonic impregnation.     

A comparison of ultrasonic cavitation intensity in liquids

Cavitation intensity in 37 organic liquids is compared with cavitation intensity in water under the same conditions. Temperature ranges are established over which cavitation intensities in these liquids are at their highest.     

Characteristics of cavitation onset and development in a self-excited fluidic oscillator

Hydrodynamic cavitation has been widely employed in modern chemical technology. A high-speed camera experiment is conducted to reveal the characteristics of hydrodynamic cavitation generated in one self-excited fluidic oscillator. The images obtained from the high-speed camera system are employed to describe several development stages of the hydrodynamic cavitation. The gray intensity of the images which is the volume of bubbles formed is extracted to distinguish the cavitation bubbles from the water. It is found that three regions in the fluidic oscillator could be divided according to the distance from the entrance. The inception of cavitation occurs in the region nearest the entrance. For a relatively low inlet flow rate, the whole process of cavitation could complete within the region that is the second nearest the entrance as a low pressure area appears periodically in this region. For a high inlet flow rate, the vortexes in the region farthest from the entrance are able to generate sufficient low pressures to induce the generation of cavitation. In addition, the intensity of cavitation could be reflected by the cavitation number in a self-excited fluidic oscillator.     

Sonoluminescence and sonochemical reactions in cavitation fields. A review

Contemporary ideas on the nature of cavitation are reviewed in this paper. The general theories of sonoluminescence and sonochemical reactions, the origin, stability and splitting of cavitation bubbles, the dynamics of cavitation field evolution, the peculiarities of cavitation effects at low intensity and low-frequency acoustic oscillations, the sonoluminescence quenching effect and some questions on the energetics of cavitation fields are discussed. The electrical theory of the splitting of cavitation bubbles may, as shown in the paper, become an alternative to the thermal theories of cavitation in the future.     

A high-temperature acoustic field measurement and analysis system for determining cavitation intensity in ultrasonically solidified metallic alloys

A high-temperature acoustic field measurement and analysis system (HTAFS) was self-designed and developed to achieve real-time acoustic field analysis and quantitative cavitation characterization within high-temperature liquids. The acoustic signal was acquired by a high-temperature resistant waveguide and calibrated by separate compensation of line and continuous spectra to eliminate frequency offsets. Moreover, a new method was proposed to derive from the continuous-spectrum sound intensity and line-spectrum sound intensity in the frequency band above 1.5 times the fundamental frequency to characterize the intensity of transient cavitation and stable cavitation. The acoustic field characteristics within solidifying liquid Al-7 %Si alloy were successfully determined by this system. With the increase of ultrasound amplitude, the acoustic pressure in the alloy melt increased to be stable, the transient cavitation intensity first rose and then declined, and the stable cavitation intensity remained unchanged. Combined with the structural evolution of the primary α(Al) phase, the transient cavitation intensity was determined to be the dominant factor for the ultrasound-induced grain refinement effect.