Structural evolution study of additions of Sb_2S_3 and CdS into GeS_2 chalcogenide glass by Raman spectroscopy

The structures of pseudo-binary GeS_2–Sb_2S_3, GeS_2–CdS, Sb_2S_3–CdS, and pseudo-ternary GeS_2–Sb_2S_3–CdS chalcogenide systems are systematically investigated by Raman spectroscopy. It is shown that a small number of [S_3Ge–GeS_3]structural units(SUs) and-S-S-/S8 groups exist simultaneously in GeS_2 glass which has a three-dimensional continuous network backbone consisting of cross-linked corner-sharing and edge-sharing [GeS_4] tetrahedra. When Sb_2S_3 is added into GeS_2 glass, the network backbone becomes interconnected [GeS_4] tetrahedra and [SbS_3] pyramids. Moreover, Ge atoms in[S_3Ge–GeS_3] SUs tend to capture S atoms from Sb_2S_3, leading to the formation of [S_2Sb–SbS_2] SUs. When CdS is added into GeS_2 glass, [Cd_4GeS_6] polyhedra are formed, resulting in a strong crystallization tendency. In addition, Ge atoms in[S_3Ge–GeS_3] SUs tend to capture S atoms from CdS, resulting in the dissolution of Ge–Ge bond. Co-melting of Sb_2S_3 or CdS with GeS_2 reduces the viscosity of the melt and improves the homogeneity of the glass. The GeS_2 glass can only dissolve up to 10-mol% CdS without crystallization. In comparison, GeS_2–Sb_2S_3 glasses can dissolve up to 20-mol% CdS,implying that Sb_2S_3 could delay the construction of [Cd_4GeS_6] polyhedron and increase the dissolving amount of CdS in the glass.     

GeS2-In2S3硫系玻璃的物化性质与晶化行为研究

认识玻璃组成-性能-结构之间关系是玻璃科学中经久不衰的研究课题之一. 在制得(100-x) GeS₂-xIn₂S₃ (x=10, 15, 20, 25或30 mol%) 系列玻璃和玻璃陶瓷样品的基础上, 利用可见-近红外透过光谱, DSC, XRD和Raman光谱等测试技术表征了随组份变化的光学带隙, 玻璃转变温度以及晶化行为等, 并结合GeS₂-Ga₂S₃玻璃研究结果探讨了Ga, In 元素及其形成的网络结构对玻璃性质的影响.研究发现, 在硫系玻璃中In比Ga对光学带隙和玻璃转变温度等性质的影响要大. 它们所形成玻璃的晶化行为也截然不同, 但与其各自的材料相图有着密切的联系. 利用偏振拉曼光谱获得玻璃网络中的基本结构单元信息.最后, 结合材料相图, 玻璃随组成变化的物化性质和晶化行为以及基本网络结构单元的认识, 探讨了玻璃的化学拓扑与网络拓扑之间的联系, 为今后研究提供一种新的研究思路.     

Photo-operated two-photon absorption effects in the GeSe2–Ga2S3–PbI2 glasses

The possibility to operate the two-photon absorption (TPA) of newly synthesized GeSe₂–Ga₂S₃–PbI₂ glasses using the CO laser beam (λ=5.5 μm) as a photoinducing one has been demonstrated. As the fundamental laser beam we have used the illumination of 10.6 μm passively modulated 0.5 ns CO₂ laser with a rate repetition of about 10 Hz. We have established that the maximal photoinduced TPA is observed for the 8% doped samples (up to 14 cm/GW), which is achieved at a pump CO laser pump power density equal to about 0.6 GW/cm². The undoped PbI₂ samples show the TPA maximum at a pump power density of about 0.2 cm/GW. The minimal TPA values were observed for the samples with 5% of PbI₂. The obtained results show that these materials can be used as effective optically operated optical limiters.     

Synthesis and physical behaviour of In2S3 films

In₂S₃ layers have been grown by close-spaced evaporation of pre-synthesized In₂S₃ powder from its constituent elements. The layers were deposited on glass substrates at temperatures in the range, 200–350 °C. The effect of substrate temperature on composition, structure, morphology, electrical and optical properties of the as-grown indium sulfide films has been studied. The synthesized powder exhibited cubic structure with a grain size of 63.92 nm and S/In ratio of 1.01. The films grown at 200 °C were amorphous in nature while its crystallinity increased with the increase of substrate temperature to 300 °C. The films exhibited pure tetragonal β-In₂S₃ phase at the substrate temperature of 350 °C. The surface morphological analysis revealed that the films grown at 300 °C had an average roughness of 1.43 nm. These films showed a S/In ratio of 0.98 and a lower electrical resistivity of 1.28 × 10³ Ω cm. The optical band gap was found to be direct and the layers grown at 300 °C showed a higher optical transmittance of 78% and an energy band gap of 2.49 eV.     

20GeS2·80Sb2S3硫系玻璃的析晶行为及动力学机理研究

实现玻璃微晶化过程控制的基础是要充分认识其析晶行为及动力学机理. 利用示差扫描量热法和析晶热处理等手段, 研究发现 20GeS₂·80Sb₂S₃硫系玻璃属于表面析晶, 在268℃(T_g+30℃)下热处理60 h, 可以获得表面约40 μm的Sb₂S₃晶层复合玻璃陶瓷样品. 在此基础上, 利用非等温法从理论上分析该玻璃的析晶动力学机理. 计算得到其析晶活化能E_c为(223.6±24.1)kJ·mol^-1, 在热处理温度(268℃)下的析晶速率常数K为1.23×10^-4 s^-1, 属于较难析晶的玻璃组成; 玻璃的晶体生长指数m和晶体生长维数n均为2, 表明其Sb₂S₃相的析晶行为是二维生长过程, 与析晶实验结果完全相符. 由此可知, 对于Sb₂S₃晶体复合的硫系玻璃陶瓷样品可通过玻璃粉末压片烧结、带铸法或丝网印刷法制备获得, 为今后功能硫系玻璃的开发提供实验依据和理论指导. 关键词： 硫系玻璃 微晶化 析晶动力学 析晶行为     

Structure determination, magnetic and optical properties of a new chromium(II) thioantimonate, [Cr((NH2CH2CH2)3N)]Sb4S7

The chromium(II) antimony(III) sulphide, [Cr((NH₂CH₂CH₂)₃N)]Sb₄S₇, was synthesised under solvothermal conditions from the reaction of Sb₂S₃, Cr and S dissolved in tris(2-aminoethyl)amine (tren) at 438 K. The products were characterised by single-crystal X-ray diffraction, elemental analysis, SQUID magnetometry and diffuse reflectance spectroscopy. The compound crystallises in the monoclinic space group P2₁/n with a=7.9756(7), b=10.5191(9), c=25.880(2) Å and β=90.864(5)°. Alternating SbS₃³⁻ trigonal pyramids and Sb₃S₆³⁻ semi-cubes generate Sb₄S₇²⁻ chains which are directly bonded to Cr(tren)²⁺ pendant units. The effective magnetic moment of 4.94(6)μ_B shows a negligible orbital contribution, in agreement with expectations for Cr(II):d⁴ in a ⁵A ground state. The measured band gap of 2.14(3) eV is consistent with a correlation between optical band gap and framework density that is established from analysis of a wide range of antimony sulphides.     

Nature of intrinsic luminescence in the glasses of CaO–Ga2O3–GeO2 system

The intrinsic luminescence of glasses of the CaO–Ga₂O₃–GeO₂ system has been investigated. High chemical purity and optical quality glasses, both undoped and doped with transition and rare-earth ions with different compositions, were obtained by high-temperature synthesis. The influences of the basic glass composition, impurities (Cr³⁺, Mn²⁺, Eu²⁺, Nd³⁺, Ho³⁺, Er³⁺, and Ce³⁺) and different kinds of excitation, on the intrinsic luminescence of the CaO–Ga₂O₃–GeO₂ glasses were investigated. The nature and possible mechanisms of the intrinsic luminescence in glasses of this system are discussed. The proposed models of intrinsic luminescence are supported by electron spin resonance spectroscopy.     

Material design of new lithium ionic conductor, thio-LISICON, in the Li2S–P2S5 system

A new lithium ionic conductor of the thio-LISICON (LIthium SuperIonic CONductor) family was found in the binary Li₂S–P₂S₅ system; the new solid solution with the composition range 0.0≤x≤0.27 in Li_3+5xP_1−xS₄ was synthesized at 700 °C and characterized by X-ray diffraction measurements. Its electrical and electrochemical properties were studied by ac impedance and cyclic voltammetry measurements, respectively. The solid solution member at x=0.065 in Li_3+5xP_1−xS₄ showed the highest conductivity value of 1.5×10⁻⁴ S cm⁻¹ at 27 °C with negligible electronic conductivity and the activation energy of 22 kJ mol⁻¹ which is characteristic of high ionic conduction state. The extra lithium ions in Li₃PS₄ created by partial substitution of P⁵⁺ for Li⁺ led to the large increase in ionic conductivity. In the solid solution range examined, the minimum conductivity was obtained for the compositions, Li₃PS₄ (x=0.0 in Li_3+5xP_1−xS₄) and Li₄P_0.8S₄ (x=0.2 in Li_3+5xP_1−xS₄); this conductivity behavior is similar to other thio-LISICON family with the general formula, Li_xM_1−yM_y′S₄ (M=Si, Ge, and M′=P, Al, Zn, Ga, Sb). Conduction mechanism and the material design concepts are discussed based on the conduction behavior and the structure considerations.     

The influence of different fabrication processes on characteristics of excess Bi2O3-doped 0.95 (Na0.5Bi0.5)TiO3–0.05 BaTiO3 ceramics

In this study, we will develop the influences of the excess x wt% (x=0, 1, 2, and 3) Bi₂O₃-doped and the different fabricating process on the sintering and dielectric characteristics of 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃ ferroelectric ceramics with the aid of SEM and X-ray diffraction patterns, and dielectric–temperature curves. The 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ ceramics are fabricated by two different processes. The first process is that (Na_0.5Bi_0.5)TiO₃ composition is calcined at 850 °C and BaTiO₃ composition is calcined at 1100 °C, then the calcined (Na_0.5Bi_0.5)TiO₃ and BaTiO₃ powders are mixed in according to 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions. The second process is that the raw materials are mixed in accordance to the 0.95 (Na_0.5Bi_0.5)TiO₃–0.05 BaTiO₃+x wt% Bi₂O₃ compositions and then calcining at 900 °C. The sintering process is carried out in air for 2 h from 1120 to 1240 °C. After sintering, the effects of process parameters on the dielectric characteristics will be developed by the dielectric–temperature curves. Dielectric–temperature properties are also investigated at the temperatures of 30–350 °C and at the frequencies of 10 kHz–1 MHz.     

Effect of WO3 on the spectroscopic properties in Er/Yb co-doped bismuth–borate glasses

The spectroscopic properties of Er³⁺/Yb³⁺ co-doped Bi₂O₃–B₂O₃–WO₃ (BBW) glasses were analyzed and discussed. The effect of WO₃ content on the absorption spectra, the Judd–Ofelt parameters Ω_t (t=2, 4, 6), emission spectra and the lifetime of the ⁴I_13/2 level and the quantum efficiency of Er³⁺:⁴I_13/2→⁴I_15/2 transition were also investigated. With the substitution of WO₃ for B₂O₃, the measured lifetime of the ⁴I_13/2 level and the quantum efficiency of Er³⁺:⁴I_13/2→⁴I_15/2 transition increase from 0.98 to 1.31 ms and from 38.2% to 49.2%, respectively. The effective width of emission band and the emission cross-section both decrease slightly. And the emission spectra is analyzed via the different curve (σ_e−σ_a) of BBW glasses, the influence of OH⁻is also discussed.     

Nonlinear refractive index measurements in antimony–sulfide glass films using a single beam nonlinear image technique

The nonlinear refractive index, n₂, of films based on the new glass system Sb₂O₃–Sb₂S₃ was measured at 1064 nm with laser pulses of 15 ps, using a single-beam nonlinear image technique in presence of a phase object. The films were prepared from bulk glasses by RF-sputtering. A large value of n₂ = 3 × 10⁻¹⁵ m²/W, which is three orders of magnitude larger than for CS₂, was determined. The result shows the strong potential of antimony–sulfide glass films for integrated nonlinear optics.     

光学碱度对Tb3+掺杂Bi2O3-B2O3玻璃发光性能的影响

采用熔融法制备了Tb³⁺掺杂的Bi₂O₃-B₂O₃系统玻璃,使用激发、发射及拉曼光谱分析了光学碱度与玻璃结构及发光性能的关系,同时绘制了Tb³⁺、Bi³⁺和Bi²⁺的能级图。研究结果表明：Tb³⁺掺杂的Bi₂O₃-B₂O₃玻璃由[BO₃]、[BiO₃]、[BO₄]及[BiO₆]共同组成,且随着光学碱度由0.63增加到0.93,玻璃的结构逐渐疏松。高的光学碱度使部分Bi³⁺变为Bi²⁺,发出571 nm（²P_3/2（2）→²P_1/2）的光,Bi³⁺→Tb³⁺的能量降低。在光学碱度及Tb³⁺、Bi³⁺和Bi²⁺离子的共同作用下,随着光学碱度的提高,玻璃的发光颜色由黄绿色变为白色。     

Tm~(3+)掺杂Ge-Ga-S玻璃微球-石英光纤锥耦合系统的荧光回廊模特性

以熔融淬冷法自制了Tm~(3+)掺杂Ge-Ga-S硫系玻璃,并以此为基质材料,用漂浮粉料熔融法制备了直径分布为50—200μm的高品质因数(Q10~4)的有源硫系玻璃微球谐振腔.在显微镜下优选出一颗表面质量好、球形度较高、直径为72.84μm的微球,与氢氧焰扫描拉锥法制备的一根腰锥直径为1.93μm的石英光纤锥进行近场耦合.根据基质材料的吸收光谱特性,选用808 nm的半导体激光器作为抽运源.实验测得光纤锥倏逝波场激发出了掺Tm~(3+)硫系玻璃微球在1460 nm附近的荧光回廊模式,其典型共振峰间隔为4.39 nm.实验测得的荧光回廊模式与米氏散射理论计算结果符合度较高(最大误差仅为0.047%),验证了本文提出的掺Tm~(3+)硫系微球制备及耦合工艺的可行性.     

Effect of deposited temperatures of the buffer layer on the band offset of CZTS/In_2S_3 heterostructure and its solar cell performance

The effect of the deposition temperature of the buffer layer In_2S_3 on the band alignment of CZTS/In_2S_3 heterostructures and the solar cell performance have been investigated.The In_2S_3 films are prepared by thermal evaporation method at temperatures of 30,100,150,and 200 ℃,respectively.By using x-ray photoelectron spectroscopy(XPS),the valence band offsets(VBO) are determined to be-0.28 ±0.1,-0.28 ±0.1,-0.34 ±0.1,and-0.42 ±0.1 eV for the CZTS/In_2S_3heterostructures deposited at 30,100,150,and 200 ℃,respectively,and the corresponding conduction band offsets(CBO)are found to be 0.3 ±0.1,0.41 ±0.1,0.22±0.1,and 0.01 ±0.1 eV,respectively.The XPS study also reveals that interdiffusion of In and Cu occurs at the interface of the heterostructures,which is especially serious at 200 ℃ leading to large amount of interface defects or the formation of CuInS_2 phase at the interface.The CZTS solar cell with the buffer layer In_2S_3 deposited at 150 ℃ shows the best performance due to the proper CBO value at the heterostructure interface and the improved crystal quality of In_2S_3 film induced by the appropriate deposition temperature.The device prepared at 100 ℃presents the poorest performance owing to too high a value of CBO.It is demonstrated that the deposition temperature is a crucial parameter to control the quality of the solar cells.     

Fluorescence spectra and homogeneous line widths of Cr in glass nucleating ferroelectric Li2Ge7O15

We report optical studies of the new material – Cr³⁺-doped lithium–germanate glass, containing Li₂Ge₇O₁₅ (LGO) nanocrystalline particles. While only broadband ⁴T₂–⁴A₂ fluorescence from the low-field octahedral Cr³⁺ sites was observed from Cr³⁺ ions in the glass, in LGO nanocrystals high-field Cr³⁺ centers emit ²E–⁴A₂ (R–lines) fluorescence. The process of crystallization in the course of isothermal annealing of glasses was monitored spectroscopically and the nucleation of LGO crystallites was observed starting from the smallest clusters. Using the ²E–⁴A₂ fluorescence spectra it is possible to detect the ferroelectric phase transition in LGO:Cr³⁺ nanocrystals, whose critical temperature was found to be similar to that of the bulk crystals. Long-lived spectral holes were burned in the inhomogeneously broadened R-lines of Cr³⁺ in LGO nanocrystals at low temperatures. The linear temperature dependence of hole widths shows that the homogeneous broadening of ⁴A₂–²E transitions of Cr³⁺ in nanocrystals is due to interaction of Cr³⁺ electronic levels with the two-level systems (TLS) of the surrounding glass. The range of the Cr³⁺-TLS elastic dipole–dipole interaction is estimated.     

Enhanced luminescence from transparent Ni-doped MgO–Al2O3–SiO2 glass ceramics by Ga2O3 addition

Transparent Ni²⁺-doped MgO–Al₂O₃–SiO₂ glass ceramics without and with Ga₂O₃ were synthetized. The precipitation of spinel nanocrystals, which was identified as solid solutions in the glass ceramics, could be favored by Ga₂O₃ addition and their sizes were about 7.6 nm in diameter. The luminescent intensity of the Ni²⁺-doped glass ceramics was largely enhanced by Ga₂O₃ addition which could mainly be caused by increasing of Ni²⁺ in the octahedral sites and the reduction of the mean frequency of phonon density of states in the spinel nanocrystals of solid solutions. The full width at half maximum (FWHM) of emissions for the glass ceramics with different Ga₂O₃ content was all more than 200 nm. The emission lifetime increased with the Ga₂O₃ content and the longest lifetime is about 250 μs. The Ni²⁺-doped transparent glass ceramics with Ga₂O₃ addition have potential application as broadband optical amplifier and laser materials.     

Optical characterization of amorphous Ga50Se45S5 films

The transmission spectra of thermally evaporated Ga₅₀Se₄₅S₅ films were measured over the wavelength range 300–900 nm. A simple method, suggested by Swanepoel, was used for the determination of the optical constants and thickness of the films. Increasing the thickness of the film beyond 450 nm does not affect the optical constants. The dependence of the absorption coefficient on the photon energy (hν) at the edge of the absorption band is well described by the relation hν=β(hν−E_opt)² with an optical gap equals 2.4 eV. A good fit of the experimental points with Tauc relation indicates that non-direct transition is the most probable mechanism responsible for the photon absorption inside the investigated film.     

Green and red up-conversion emissions of Er–Yb Co-doped TiO2 nanocrystals prepared by sol–gel method

In this paper, green and red up-conversion emissions of Er³⁺–Yb³⁺ co-doped TiO₂ nanocrystals were reported. The phase structure, particle size and optical properties of Er³⁺–Yb³⁺ co-doped TiO₂ nanocrystals samples were characterized by using X-ray diffraction (XRD), transmission electron microscopy (TEM), UV–vis–NIR absorption spectra and photoluminescence (PL) spectra. Green and red up-conversion emissions in the range of 520–570 nm (²H_11/2, ⁴S_3/2→⁴I_15/2) and 640–690 nm (⁴F_9/2→⁴I_15/2) were observed for the Er³⁺–Yb³⁺ co-doped TiO₂ nanocrystals. The visible up-conversion mechanism and temperature dependence of up-conversion emission for Er³⁺ in TiO₂ nanocrystals were discussed in detail.     

Investigation of 1.3 μm emission in Nd-doped bismuth-based oxide glasses

Nd₂O₃-doped 43Bi₂O₃–xB₂O₃–(57−x)SiO₂–1.0Nd₂O₃ (x=57, 47, 39, 28.5, 19.5, 10, 0 mol%) bismuth glasses were prepared by the conventional melt-quenching method, and the Nd³⁺: ⁴F_3/2→⁴I_13/2 fluorescence properties had been studied in an oxide system Bi₂O₃–B₂O₃–SiO₂. The Judd–Ofelt analysis for Nd³⁺ ions in bismuth boron silicate glasses was also performed on the basis of absorption spectrum, and the transition probabilities, excited-state lifetimes, the fluorescence branching ratios, quantum efficiency and the stimulated emission cross-sections of ⁴F_3/2→⁴I_13/2 transition were calculated and discussed. The stimulated emission cross-sections of 1.3 μm were quite large due to a large refractive index of the host. Although the effective bandwidths decreased with increasing SiO₂ content, quantum efficiencies and stimulated emission cross-sections enhanced largely with increasing SiO₂ content.     

Absorption coefficients of O3 at CO2 laser wavelengths

The O₃ absorption coefficients for the rotational lines P(12)–P(28) of the 9.4 μm emission band of the CO₂ laser are presented. Measurements were made in O₃–air dilute mixtures (20–600 ppm) at 25°C and a total pressure of 1013.25 h Pa using a frequency stabilized cw CO₂ laser and values have been determined with greater precision than in previously reported studies.