二维二氧化硅改性聚环氧乙烷基固态聚合物电解质用于增强锂离子电池性能

通过改性由酸蚀二维蛭石制备的二维二氧化硅,得到带正电荷的二维介孔二氧化硅(PSN⁺)纳米片,并将PSN⁺用作聚环氧乙烷(PEO)基固体聚合物电解质(SPEs)的填料。由于PSN⁺具有丰富的正电荷,PSN⁺与锂盐解离的阴离子能够有效结合,从而促进锂离子的运输,获得较好的锂离子转移数。在50℃时,基于PSN⁺的SPEs表现出较高的离子电导率(7.5×10^-5 S·cm^-1),锂离子迁移数为0.30,稳定电压窗为4.41 V。因此,组装后的LiFePO₄锂电池在50℃、0.2C下具有优异的初始放电比容量(155.7 mAh·g^-1),在循环100次后容量保持率为97.1%。     

二维层状Ti3C2Tx-MXene@VS2用于高性能锂离子电池负极

为探索一种高性能的锂离子电池负极材料,采用酸刻蚀法制备了高导电性、高稳定性的二维层状Ti₃C₂T_x,通过溶剂热法制备了具有高理论比容量的花瓣状VS₂纳米片,再经过简单的液相混合得到了二维层状Ti₃C₂T_x-MXene@VS₂复合物。通过扫描电子显微镜、透射电子显微镜、X射线光电子能谱、X射线衍射和能谱分析对复合材料的形貌和结构进行了表征,采用循环伏安、恒流充放电、长循环和交流阻抗谱对复合材料的电化学性能进行了研究。结果表明：VS₂纳米片均匀地分布在Ti₃C₂T_x的层间及表面,该复合物具有高的可逆容量(电流密度为0.1A·g^-1时,比容量为610.5mAh·g^-1)、良好的倍率性能(电流密度为2A·g^-1时,比容量为197.1mAh·g^-1)和良好的循环稳定性(电流密度为0.2 A·g^-1时,循环600圈后比容量为874.9 mAh·g^-1;电流密度为2 A·g^-1时,循环1 500圈后比容量为115.9mAh·g^-1)。     

添加剂对离子液体凝胶聚合物电解质电化学性能的影响

本文采用1-乙基-3-甲基咪唑六氟磷酸盐(EMIPF₆)、六氟磷酸锂(LiPF₆)和偏氟乙烯-六氟丙烯共聚物(P(VdF-HFP))为原料制得P(VdF-HFP)-EMIPF₆-LiPF₆体系离子液体凝胶聚合物电解质,选取碳酸甲乙酯(EMC)、碳酸二甲酯(DMC)、碳酸二乙酯(DEC)以及碳酸乙烯酯(EC)和碳酸丙烯酯(PC)混合物(EC-PC)作为离子液体凝胶聚合物电解质的添加剂,分别研究了它们对聚合物电解质膜电化学性能的影响。结果表明：加入EC-PC的P(VdF-HFP)-EMIPF₆-LiPF₆电解质膜的电化学窗口达到4.6 V,锂离子迁移数为0.44,30 ℃时离子电导率为1.65 mS·cm^-1;而DEC、DMC、EMC对电解质膜的电化学稳定性、锂离子迁移数存在不良的影响,对离子电导率的提高不明显。研究了正极材料LiCoO₂在P(VdF-HFP)-EMIPF₆-LiPF₆+EC-PC电解质中的充放电循环性能,其首次放电比容量达到116.5 mAh·g^-1,充放电20次后,电池容量没有明显衰减。     

负极材料NiO的制备及电化学性能

以Ni(NO₃)₂·6H₂O和NaOH为原料,采用水热法合成了锂离子电池负极材料NiO。通过TG-DSC分析，确定了合成过程的反应机理。通过XRD、SEM和恒流充放电测试,研究了NiO样品的结构、形貌及电化学性能。400 ℃焙烧得到立方结构的NiO产品，以0.10 mA·cm^-2充放电,首次放电比容量达到1 151 mAh·g^-1，经过20次循环后的比容量仍为776 mAh·g^-1。     

溶胶-凝胶法合成Li1-xNaxMn2O4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na⁺离子掺杂的Li_1-xNa_xMn₂O₄(x=0,0.01,0.03,0.05)。X射线衍射图表明Na⁺取代Li⁺进入Li_1-xNa_x Mn₂O₄晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_0.97Na_0.03Mn₂O₄在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn₂O₄从51.2%提升到84.1%。循环伏安测试表明Na⁺离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li_0.97Na_0.03Mn₂O₄仍有79.0 mAh·g^-1的放电容量,高于未掺杂样品的52.1 mAh·g^-1。Na⁺离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn₂O₄的电化学性能,是一种可行的改性方法。     

碳酸盐共沉淀法可控制备超高倍率锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2

采用碳酸盐共沉淀法通过调节NH₃·H₂O用量来实现可控制备超高倍率纳米结构LiNi_1/3Co_1/3Mn_1/3O₂正极材料。NH₃·H₂O用量会对颗粒的形貌、粒径、晶体结构以及材料电化学性能产生较大的影响。X射线衍射（XRD）分析和扫描电镜（SEM）结果表明,随着NH₃·H₂O用量的降低,一次颗粒形貌由纳米片状逐渐过渡到纳米球状,且n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品晶体层状结构最完善、Li⁺/Ni²⁺阳离子混排程度最低。电化学性能测试结果也证实了n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品具有最优异的循环稳定性和超高倍率性能。具体而言,在2.7~4.3 V,1C下循环300次后的放电比容量为119 mAh·g^-1,容量保持率为81%,中值电压基本无衰减（保持率为97%）。在100C（18 Ah·g^-1）的超高倍率下,放电比容量还能达到56 mAh·g^-1,具有应用于高功率型锂离子电池的前景。此NH₃·H₂O比例值对于共沉淀法制备其他高倍率、高容量的正/负极氧化物材料具有一定的工艺参考价值。     

包覆ZrO2锂离子筛的制备及其在盐湖卤水中的吸附性能

采用水热法制备前驱体Li_1.6Mn_1.6O₄,用液相沉淀法在其表面包覆ZrO₂,再经酸洗转型为包覆ZrO₂的锂离子筛H_1.6Mn_1.6O₄。采用XRD、SEM、EDS和HRTEM对前驱体的结构、形貌和成分进行了表征。研究了ZrO₂包覆量和焙烧温度对锰溶损率和锂吸附容量的影响。结果表明：当ZrO₂包覆量为3%,焙烧温度为450℃时,在前驱体表面形成厚度约15 nm的ZrO₂包覆层,首次锰溶损率从3.14%下降到2.65%,锂离子筛在盐湖卤水中锂吸附容量保持为29.4 mg·g^-1。包覆ZrO₂的锂离子筛经过10次循环吸附-脱附,锰溶损率降低至0.34%,锂吸附容量保持为24.4 mg·g^-1,高于未包覆的锂离子筛（22.9 mg·g^-1）。包覆ZrO₂改善了锂离子筛的结构和吸附容量的循环稳定性。     

阳离子(从有机铵到无机阳离子)对fac-[Fe(CO)3I3]-阴离子的稳定性和毒性的调节

通过无机碘盐(MI_n)与 cis-[Fe(CO)₄I₂]反应制备了 5 个盐类化合物 fac-M[Fe(CO)₃I₃]_n (Mⁿ⁺=Na⁺ (1),K⁺ (2),Mg²⁺ (3),Ca²⁺ (4),NH₄⁺ (5)),探讨了阳离子Mⁿ⁺对fac-[Fe(CO)₃I₃]^-阴离子的稳定性和细胞毒性的影响。通过傅里叶变换红外光谱(FTIR)监测,发现盐 1~5在 DMSO、D₂O、生理盐水等介质中均能缓释 CO,其释放动力学符合一级反应动力学模型;还发现溶液中碘离子的浓度和酸度对该阴离子的缓释CO性能也具有调节作用。通过噻唑蓝(MTT)实验评估了盐1~5对膀胱癌细胞的毒性,其24 h半抑制浓度(IC₅₀)在 25~43 μmol·L^-1。与有机铵阳离子类的盐化合物相比,盐1~5在含水介质中的释放 CO速率下降,毒性亦有下调。研究还发现这类fac-[Fe(CO)₃I₃]^-阴离子在缓释CO的同时释放碘自由基,并能导致线粒体活性氧(ROS)水平、Parkin蛋白表达均上调。铁死亡抑制剂(Ferrostatin-1和Liproxstatin-1)试验结果表明这类化合物可能引发铁死亡通路并促进肿瘤细胞死亡。     

构建一维铜基配位聚合物作为锂离子电池正极材料

合成了一种新型的一维(1D)羰基配位聚合物[Cu (BGPD)(DMA)(H₂O)]·DMA (记为Cu-BD,H₂BGPD=N,N′-双(甘氨酰)均苯四甲酸二酰亚胺,DMA=二甲基乙酰胺),并考察了其用作锂离子电池正极材料的电化学性能。电化学测试结果表明,Cu-BD正极在50 mA·g^-1的电流密度下循环100圈后仍然保留50 mAh·g^-1的比容量,具有较好的循环稳定性。Cu-BD电极反应机理研究表明,BGPD^2-配体和Cu (Ⅱ)离子在充放电过程中都可能参与了电子转移过程。     

改性硅藻土负载亚铁氰化铜复合物的制备及其对Cs+的吸附性能

采用水热法、以氯化铝为铝源对硅藻土(De)进行改性,通过浸渍法将亚铁氰化铜(KCuHCF)纳米颗粒负载于改性De表面,制备出γ-AlOOH/De-KCuHCF和γ-Al₂O₃/De-KCuHCF两种复合吸附剂,对所制备的吸附剂进行了表征,并研究了其对Cs⁺的吸附性能。结果表明,所制备吸附剂具有优异的Cs⁺吸附性能,γ-AlOOH/De-KCuHCF和γ-Al₂O₃/De-KCuHCF最高吸附容量分别可达75.44、84.02 mg·g^-1,γ-Al₂O₃/De-KCuHCF对模拟卤水中Cs⁺的吸附率高达97.55%;以3 mol·L^-1 NH₄NO₃为脱附剂,经3级连续脱附后,γ-Al₂O₃/De-KCuHCF的Cs⁺脱附率可达81.88%,经过5次吸附-脱附循环后仍保持了较高的吸附量。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.