谷胱甘肽稳定的CdTe量子点荧光猝灭法测定痕量过氧化氢

以谷胱甘肽稳定的CdTe量子点作为荧光探针,基于荧光猝灭法对过氧化氢进行了定量检测,考察了缓冲溶液体系、量子点浓度、反应时间等多种因素的影响。实验结果表明,在pH=7.2的Na2HPO4-NaH2PO4缓冲液中,反应时间为15min,过氧化氢浓度为1.0×10-6～3.0×10-5 mol/L范围时,其线性回归方程为△F=9.78+7.56c(10-6 mol/L),线性相关系数和检测限分别为0.9992和1.27×10-8 mol/L。谷胱甘肽稳定的CdTe量子点荧光猝灭法已用于水样的测定,回收率在96%～103%之间,相对标准偏差RSD不大于3.3%,结果令人满意。     

CdTe/CdS半导体量子点作为农药百草枯的高灵敏传感器

用硫普罗宁(Tiopronin, TP)作为稳定剂合成了水溶性的高荧光CdTe/CdS量子点. 研究了该量子点与10种农药的相互作用. 实验发现, 当农药浓度为4.76×10^-6 mol/L时, 农药百草枯(Paraquat)能显著猝灭CdTe/CdS量子点的荧光, 使其荧光强度下降87.3%, 而分别加入乙酰甲胺磷及辛硫磷等其它9种农药, 仅能使CdTe/CdS量子点的荧光强度下降0.1%～5.1%, 显示了该CdTe/CdS量子点对百草枯的特异性传感作用. 采用吸收光谱和时间分辨荧光动力学研究了百草枯对CdTe/CdS量子点的荧光猝灭机理. 计算得出荧光强度猝灭的Stern-Volmer常数K为2.03×10⁶, 而寿命猝灭的Stern-Volmer常数K为4.25×10⁵. 结果表明, 百草枯对CdTe/CdS量子点的荧光猝灭主要为静态过程, 而动态过程的贡献较小. 利用二者的猝灭作用建立了对农药百草枯的高灵敏检测新方法, 校正曲线的线性范围为9.90×10^-9～1.50×10^-6 mol/L, 检出限为6.35×10^-9 mol/L, R=0.999. 用该方法对3种食品和3种水样中残留农药进行了检测, 加标回收率均在82.2%～98.5%之间, 其相对标准偏差为2.62%~8.35%.     

磁性量子点电致化学发光法测定李氏禾提取液中的过氧化氢

利用巯基乙酸水热法合成出表面修饰—COOH的CdTe量子点,并将CdTe量子点(QDs)连接在Fe3O4纳米粒子表面,制备出CdTe/Fe3O4磁性量子点。通过磁力将磁性量子点修饰于石墨电极表面。在pH7.5的PBS缓冲溶液中,H2O2可使CdTe量子点产生电致化学发光,H2O2浓度在4～100μmol/L范围内与CdTe量子点的电致化学发光强度呈良好的线性关系,检出限为0.24μmol/L。据此建立了测定样品中过氧化氢含量的电致化学发光分析法,并成功地应用于李氏禾草汁原液中过氧化氢含量的测定。该研究借助纳米Fe3O4的磁力特征,使敏感膜易于形成和更新分离,简化了实验操作,同时起到增强发光强度的作用。     

Use of surface-modified CdTe quantum dots as fluorescent probes in sensing mercury (II)

Thioglycolic acid (TGA)-capped CdTe quantum dots (QDs) were synthesized in aqueous medium, and their interaction with metal cations was studied with UV-vis absorption, steady-state and time-resolved fluorescence spectra. The results demonstrated that Hg(II), Cu(II) and Ag(I) could effectively quench the QD emission based on different action mechanisms: Cu(II) and Ag(I) quenched CdTe QDs because they bound onto particle surface and facilitated non-radiative electron/hole recombination annihilation of QDs; electron transfer process between the capping ligands and Hg(II) was mainly responsible for the remarkable quenching effect of Hg(II). To prevent the approach of metal cations to QD core, the original TGA-capped CdTe QDs were further coated by denatured bovine serum albumin (dBSA). It was found that the dBSA-coated CdTe QDs could be quenched effectively by Hg(II), but Cu(II) and Ag(I) could hardly quench the QDs even at fairly higher concentration levels because the dBSA shell layer effectively prevented the binding of metal cations onto the QD core. On the basis of this fact, a simple, rapid and specific method for Hg(II) determination was proposed. Under optimal conditions, the quenched fluorescence intensity increased linearly with the concentration of Hg(II) ranging from 0.012 x 10(-6) to 1.5 x 10(-6) mol L(-1). The limit of detection for Hg(II) was 4.0 x 10(-9) mol L(-1). The developed method was successfully applied to the detection of trace Hg(II) in real samples.     

Aqueous synthesis of type-II core/shell CdTe/CdSe quantum dots for near-infrared fluorescent sensing of copper(II)

Type-II core/shell CdTe/CdSe quantum dots (QDs) were synthesized in aqueous medium by employing thiol-capped CdTe QDs as core template and CdCl(2) and Na(2)SeSO(3) as shell precursors, respectively. Compared with the original CdTe cores, the core/shell CdTe/CdSe QDs showed an obvious red-shifted emission with the color-tune capability to the near-infrared (NIR) wavelength, because of the formation of an indirect excitation. The prepared QDs exhibited high stability and moderate fluorescence quantum yields (10-20%), and their core/shell heterostructure was characterized by UV-vis absorption, steady-state and time-resolved fluorescence spectra, X-ray powder diffraction, X-ray photoelectron spectroscopy and high-resolution transmission electron microscopy. The fluorescence of the core/shell QDs could be markedly quenched by Cu(II), and approximate concentrations of other physiologically important cations, such as Zn(II), Ca(II), Na(I) and K(I) etc., had no effect on the fluorescence. Based on this, a simple and rapid method for Cu(II) determination was proposed using the NIR CdTe/CdSe QDs as fluorescent probes. Under optimal conditions, the response was linearly proportional to the concentration of Cu(II) between 0.05 to 50.0 x 10(-6) mol L(-1), the limit of detection was 2.0 x 10(-8) mol L(-1). The developed method was successfully applied to the detection of trace Cu(II) in real samples.     

表面修饰CdTe量子点的合成及其光学特性

在水相中合成高发光性能的CdTe量子点,研究以巯基乙酸(TGA)为稳定剂对CdTe表面进行修饰,制备在水中分散性良好的纳米晶,通过对CdTe量子点合成反应条件的摸索,掌握了其合成的反应规律.同时用紫外分光光度计、荧光分光光度计和透射电子显微镜对其进行了表征.结果表明,回流时间、n(Cd²⁺):n(HTe^-)、反应物浓度、TGA用量、反应体系pH值,对纳米晶的光学性质具有显著影响.回流2 h制得的CdTe纳米粒子直径约为5 nm,其发射峰窄且对称,表现出良好稳定的光学性质.     

水溶性CdTe量子点的合成及其用于荧光猝灭法测定肌红蛋白

以3-巯基丙酸为稳定剂,合成了具有特殊光学性质的水溶性CdTe量子点,其最大发射波长位于544 nm.利用荧光光谱、紫外可见光谱及圆二色光谱法系统的研究了CdTe量子点与肌红蛋白(Mb)二者结合前后体系光谱的变化,从而证实了CdTe量子点与Mb之间静电结合反应的特征.在pH 7.0的PBS缓冲液中,用CdTe量子点作为荧光探针研究了肌红蛋白与量子点的相互作用,并基于肌红蛋白对CdTe量子点有显著的荧光猝灭作用,建立了肌红蛋白的快速检测方法.在最佳实验条件下,该体系荧光强度的猝灭程度(△F)与肌红蛋白质量浓度呈良好的线性关系,线性范围为0.3～24 μg/mL,检出限为0.13 μg/mL.该方法已对合成样品中肌红蛋白进行检测,并用于人体尿样中肌红蛋白的测定.     

CdTe量子点与罗丹明6G间的荧光共振能量转移机理研究

本文在合成水溶性巯基乙酸修饰的CdTe量子点的基础上,研究了CdTe量子点与罗丹明6G之间的荧光共振能量转移.实验结果表明:构建的CdTe量子点(供体)-罗丹明6G(受体)荧光共振能量转移体系在磷酸盐缓冲溶液中有较好的转移效果.当磷酸缓冲溶液pH值为7.4,NaCl浓度为1.0 mol/L时,构建的CdTe量子点-罗丹...     

Development of a novel deltamethrin sensor based on molecularly imprinted silica nanospheres embedded CdTe quantum dots

A novel procedure for the determination of deltmethrin (DM) is reported. The water-soluble CdTe quantum dots (QDs) and highly fluorescent silica molecularly imprinted nanospheres embedded CdTe QDs (CdTe-SiO2-MIPs) were prepared and characterized by fluorescence spectroscopy, UV-vis spectroscopy, TEM and IR. The fluorescence nanosensor based CdTe-SiO2-MIPs is developed. The possible quenching mechanism is discussed by DM. Under optimal conditions, the relative fluorescence intensity of CdTe-SiO2-MIPs decreased with increasing DM by a Stern-Volmer type equation in the concentration range of 0.5-35.0 μg mL(-1), the corresponding detection limit is 0.16 μg mL(-1). The developed sensor based on CdTe-SiO2-MIPs was applied to determine DM in fruit and vegetable samples.     

Studying the interaction between CdTe quantum dots and Nile blue by absorption,fluorescence and resonance Rayleigh scattering spectra

Thioglycolic acid (TGA) capped CdTe quantum dots (QDs) with the diameter of 2–3 nm were synthesized. The interaction between CdTe QDs and Nile blue (NB) was investigated by ultraviolet–visible (UV–vis) absorption, resonance Rayleigh scattering (RRS) and fluorescence spectroscopy. UV–vis absorption spectrum of CdTe QDs and NB obviously changed, showing that CdTe QDs could associate with NB to form a new complex. At pH 6.8, NB effectively quenched the fluorescence of CdTe QDs. It was proved that the fluorescence quenching of CdTe QDs by NB was mainly result of the formation of CdTe QDs–NB complex, electrostatic attraction and hydrophobic forces played a major role in stabilizing the complex. The binding molar ratio of CdTe QDs and NB was 5:1 by a mole-ratio method. The interaction between CdTe QDs and NB lead to the remarkable enhancement of RRS and the enchantments were in proportional to the concentration of NB in a certain range. The mechanism of the interaction between CdTe QDs and NB, reasons for the enhancement of RRS intensity were also discussed. The obtained results suggested the more satisfactory mechanism for the interaction between CdTe QDs and NB.     

Detection of ascorbic acid and folic acid based on water-soluble CuInS(2) quantum dots

In this paper, water-soluble CuInS(2) ternary quantum dots (QDs) modified by mercaptopropionic acid (MPA) were directly synthesized by hydrothermal method. Ascorbic acid (AA) can induce the fluorescence enhancement of MPA-capped CuInS(2) QDs and can be used for the detection of AA. Under the optimized conditions, the relationship between the fluorescence intensity of the CuInS(2) QDs and AA concentration was linear in the range of 0.25-200 μmol?L(-1). Most relevant molecules and physiological ions had no effect on the detection of AA. The fluorescence intensity of CuInS(2) QDs enhanced by a certain amount of AA could be reduced in the presence of folic acid (FA) and thus can be used for the detection of FA with the linear range of 0.2-100 μmol?L(-1). Compared with previous reports, the established approach utilized a simple, sensitive, and selective strategy to develop the QDs probe based on fluorescence enhancing and quenching phenomena without complicated immobilization.     

CdTe量子点荧光猝灭法测定奥沙利铂中微量银

以谷胱甘肽作为稳定剂,100℃恒温回流,直接合成水溶性CdTe量子点。基于Ag+对合成的CdTe量子点的荧光猝灭效应,建立了测定抗癌药物奥沙利铂中微量银的方法。考察了量子点浓度、缓冲液种类、缓冲液浓度、缓冲液pH和反应时间对银离子测定的影响。当量子点浓度为0.004 g/L时,在0.10 mmol/LpH7.4的磷酸缓冲溶液中,反应时间为5 min,体系的相对荧光强度与Ag+的质量浓度呈良好的线性关系,其线性范围为16.42～98.50μg/L,线性相关系数为0.9975,检出限为0.12μg/L。     

水溶性量子点标记狂犬病P蛋白单克隆抗体的研究

利用共价偶联的方式,在水溶性缩合剂1-乙基-(3-二甲基氨基丙基)碳二亚胺盐酸盐(EDC)和N-羟基硫代琥珀酰亚胺(Sulfo-NHS)促进作用下,将400 μL的2 g/L狂犬病P蛋白抗体与适量的聚丙烯酸修饰后的水溶性硫脲修饰ZnO掺Cd量子点进行共价偶联反应,经磷酸盐缓冲液(PBS,0.01 mol/L,pH 7.4)透析纯化得到目标偶联物,采用荧光发射光谱、生物质谱、酶联免疫法等对偶联物进行表征.结果表明:偶联后的量子点荧光最大发射波长红移了10 nm,荧光强度随着狂犬病P蛋白抗原浓度的增加而逐渐增强;量子点标记狂犬病P蛋白抗体后的分子离子峰在m/z 67580处,比狂犬病P蛋白抗体分子离子峰增大了1453.由此证实狂犬病P蛋白抗体成功偶联到水溶性量子点上,且结构未受破坏.     

基于L-半胱氨酸/CdTe量子点修饰电极的电化学传感器的制备及其对Pb~(2+)的检测

成功制备了由L-半胱氨酸和CdTe量子点作为修饰材料的电化学传感器并用于水体中Pb~(2+)的检测。巯基丙酸修饰的CdTe量子点通过水相合成,表面含有大量羧基,与L-半胱氨酸表面的氨基形成酰胺键,修饰于金电极表面。通过荧光分光光度计、透射电子显微镜、红外光谱、X射线衍射对L-Cys/CdTe QDs复合材料进行表征。采用循环伏安法(CV)研究了L-Cys/CdTe QDs修饰成分在金电极上的电化学性能及CdTe量子点的最佳自组装时间。采用差分脉冲溶出伏安法(DPSV)研究了铅离子在修饰电极上的电化学行为。在优化实验条件下,Pb~(2+)浓度在1.0×10~(-6)~1.0×10~(-2) mol/L范围内与其峰电流呈良好的线性关系,相关系数(r2)为0.993 8,检出限(3σ,n=5)为4.0×10~(-7) mol/L。该传感器具有良好的重现性和稳定性,有望用于实际水样中铅离子的检测。     

CdTe/CdSe核壳量子点的合成及其在指纹显现中的应用

以CdCl2和Te粉为原料,在水相中合成了CdTe量子点核;通过外延生长在CdTe量子点核上包覆一层CdSe量子点,得到具有良好荧光性能的CdTe/CdSe核壳量子点;采用X射线衍射仪、透射电镜、高分辨透射电镜分析了不同反应条件下合成的CdTe/CdSe核壳量子点的晶体结构和微观结构,并对其进行了荧光光谱等测试和指纹显现分析.结果表明,合成的CdTe和CdTe/CdSe量子点粒径在3～5nm之间,粒径分布窄,水分散性良好;可以通过控制反应时间和Te/Se比等得到在500～700nm显示荧光发射峰的CdTe/CdSe核壳量子点.此外,核壳CdTe/CdSe量子点可以有效地和指纹物质结合,可应用于对铝合金油潜指纹的鉴别.     

Synthesis of functionalized CdTe/CdS QDs for spectrofluorimetric detection of BSA

Luminescent quantum dots (QDs)-semiconductor nanocrystals are a promising alternative to organic dyes for fluorescence-based applications. We have developed procedures to use CdS to encapsulate CdTe and synthesize a new kind of functionalized CdTe/CdS QDs for the quantitative and selective determination of bovine serum albumin (BSA). Maximum fluorescence intensity was produced at pH 6.83, with excitation and emission wavelengths at 336 and 524 nm, respectively. Under optimal conditions, the straight line equation: DeltaF=6.84+62.29C (10(-6) mol dm(-3)) was found between the relative fluorescence intensity and the concentration of BSA in the range of 0-1.2 x 10(-6) mol dm(-3), and the limit of detection was 5.4 x 10(-8) mol dm(-3). Based on this approach, a novel quantitative method for the determination of BSA is presented in this paper.     

量子点-卟啉纳米复合体系在肿瘤细胞成像中的应用

本文合成了高荧光量子产率、单分散性好的水溶性CdTe量子点(quantum dots,QDs),并与α,β,γ,δ-四(1-甲基吡啶嗡-4-基)卟吩对甲苯磺酸盐(TMPyP)组装成QDs-TMPyP纳米复合物,研究了该复合物检测DNA的机理以及肿瘤细胞成像。结果显示,QDs-TMPyP纳米复合物通过光致电子转移机制检测DNA,当CdTe QDs和CdTe QDs-TMPyP浓度低于1.0μmol/L时,HeLa肿瘤细胞存活率达92%以上,表现出低的细胞毒性。0.2μmol/L CdTe QDs-TMPyP作用于肿瘤细胞时,细胞生长状态良好,对细胞内能谱分析发现细胞内含有Cd和Te原子。CdTe QDs-TMPyP复合物比CdTe QDs更易被HeLa细胞摄取,利用量子点荧光成功实现了细胞核内成像,为宫颈癌细胞药物输送和细胞成像的深入研究打下基础。     

紫外-可见吸收、荧光光谱研究CdTe/CdS量子点与盐酸药根碱的相互作用及其应用

合成了巯基乙酸（TGA）修饰的壳核型CdTe/CdS量子点（TGA-CdTe/CdS QDs）。 利用紫外-可见光谱吸收、荧光光谱研究TGA-CdTe/CdS QDs与盐酸药根碱（JH）的相互作用机理。 在pH值为7.4的tris-HCl缓冲溶液介质中,QDs与JH相互作用后使QDs的荧光呈线性猝灭,并有良好的线性关系（r=0.999 1）,线性范围0.011~10 mg/L,检出限（3σ）为3.3×10-3 mg/L,因此可以作为一种快速、简便、定量测定盐酸药根碱的新方法。     

基于石墨烯和量子点自组装膜的能量转移构筑的高灵敏度DNA界面荧光传感

以QDs作为荧光探针, HIV1病毒序列DNA为研究对象, 设计了Quartz/PDDA/PSS/PDDA/CdTe/ssDNA自组装膜, 利用氧化石墨烯(GO)猝灭自组装膜上CdTe QDs的荧光, 而靶DNA(tDNA)与自组装膜表面ssDNA的互补配对作用使GO与CdTe QDs的距离增加, 导致自组装膜上量子点的荧光恢复, 由此建立了一种基于GO与QDs自组装膜之间荧光共振能量转移的快速灵敏检测DNA的界面分析方法, 检出限为7.26×10^-14 mol/L. 本方法制备的DNA探针操作简单, 自组装膜表面修饰的ssDNA提高了方法的选择性, GO的猝灭作用降低了检测背景, 极大地提高了荧光分析方法的灵敏度.     

镍配合物分子印迹光电流型传感器的研究

制作了一种基于光电流检测的分子印迹传感器,并应用于Ni2+测定。此传感器以CdTe量子点为光电材料,将量子点覆盖在导电玻璃表面,并在此层上以光聚合法制作镍-1-(2-吡啶偶氮)-2-萘酚( PAN)分子印迹膜。365 nm紫外光作为激发光源,量子点在光照下生成电子-空穴对,电子与电子受体-抗坏血酸作用形成的光电流作为检测信号,根据“门效应”进行Ni2+检测。实验中对配合物进行了红外表征,对量子点进行了紫外和荧光表征,对洗脱吸附时间和底液中抗坏血酸浓度的用量进行了优化。实验表明Ni2+浓度在5×10-11~5×10-8 mol/L的范围内与光电流大小呈线性关系,检出限达8.3×10-12 mol/L。此传感器具有较好的选择性,已用于水样分析。