硅氧烷改性水性聚氨酯的制备及性能

A series of novel aqueous emulsion of siloxane modified polyurethane (PU(PE-PSI)) were synthesized based on poly(propylene glycol) (PPG), polyether-grafted polysiloxane (PE PSI), 2,4-tolylene diisocyanate (TDI), dimethylol propionic acid (DMPA) and 1,4 butanediol (BDO) through a direct water emulsification of triethylamine (TEA). The aqueous emulsion was transparent and had a good stability. Fourier transform infrared spectroscopy (FTIR) was used to identify the structure of PU (PE PSI), indicating that the polysiloxane segment had been incorporated with polyurethane chain. Investigation of Electron Spectroscopy for Chemical Analysis (ESCA) and the water contact angle demonstrated that the siloxane migrated to the surface of film. The results also showed that PU(PE-PSI) was still a very good elastomer. With increasing the content of PE PSI, the resistance to water improved and tensile strength increased, while the ultimate elongation decreased slightly for the PU(PE-PSI) film.     

拒水型有机硅改性聚氨酯嵌段共聚物的合成与表征

以氨丙基硅氧烷偶联剂和端羟基聚二甲基硅氧烷(PDMS)为原料,合成了端氨丙基聚二甲基硅氧烷低聚物(SN2),并将其作为扩链剂,制备了有机硅-聚氨酯(Si-PU)嵌段共聚物.考察了聚氨酯预聚体的加料比(rNCO/OH)、SN2与聚氨酯预聚体的加料比(rNH2/NCO)对Si-PU嵌段共聚物溶液流变行为及其膜性能的影响.研究发现,该Si-PU共聚物的异丙醇溶液呈现较低的表观黏度及牛顿特性;成膜时,有机硅链段向表面迁移;膜表面对水的接触角达110°以上,且随着有机硅链段含量的增高而增大;共聚物膜的24 h吸水率较低(<1.5 wt%);但当有机硅链段含量过高时,吸水率反而增高.     

有机硅氧烷改性St/BA/AA三元共聚乳液的制备

采用核壳乳液聚合法,制备了乙烯基三乙氧基硅烷（VTES）改性的St/BA/AA三元共聚乳液,其结构经FT IR确证。研究了VTES用量、乳化剂用量及配比和引发剂用量对单体转化率和粒径的影响。结果表明：在最优条件［48%St, 48%BA, 4%AA, 1%N-MA, 4%VTES, 8%乳化剂（OP-10/SDS=1/3）, 0.8%引发剂］下,单体转化率为95.8%,平均粒径242 nm。并研究了改性St/BA/AA乳胶膜(1)的耐溶剂性和铅笔硬度。结果表明：1具有良好的耐溶剂性,铅笔硬度为2H。     

硅丙型核壳结构乳胶粒子的制备及成膜过程

采用分步乳液聚合方法, 分别在不同步骤中将乙烯基硅氧烷单体作为共聚单体引入聚丙烯酸酯类乳液共聚合体系中, 制备出具有窄分布多层核壳结构形态的硅丙型乳胶粒子. 利用透射电子显微镜(TEM)表征, 乳胶粒子具有硅丙型核壳结构; 动态激光散射(DLS)分析得到的乳胶粒子的直径与TEM数据相符; 同时由多频调制差示扫描量热(TOPEM-DSC)技术分析得到的乳胶粒子的3个玻璃化转变温度与实验设计相符, 证实乳液粒子的核壳结构; 利用Horus成膜仪对乳胶粒子成膜过程进行全程监控. 利用多种助剂制得水性木器涂料, 其漆膜的硬度、耐丙酮性、耐水性、耐醇性及耐压痕等性能优异.     

Preparation and surface properties of latexes with fluorine enriched in the shell by silicon monomer crosslinking

A series of core-shell acrylic copolymer latexes containing fluorine enriched in the shell have been prepared by emulsion polymerization of a variety of hydrocarbon monomers with (perfluoroalkyl)methyl methacrylate and vinyltriethoxysilicone. In the presence of a reactive anionic and a long chain anionic-nonionic emulsifier, the core-shell latexes were prepared and characterized by transmission electron microscopy (TEM) and tapping-mode atomic force microscopy (AFM). From AFM and contact angle measurements, it was observed that the resulting fluorine and silicon-containing acrylic copolymers with surface energy as low as 15.5 mN/m formed a dense and gradient film containing a surface layer with high a fluorine content, and that the fluorinated particles can be fixed on the surface due to the crosslinking reaction of multi-functional silicon monomer even though the fluorinated carbon number was not enough to crystallize.     

荧光探针法研究乳化剂对硅/丙核壳乳液聚合行为的影响

用荧光探针(芘)法测定了十二烷基硫酸钠(SDS)、烷基酚聚氧乙烯醚(OP-10),以及复配乳化剂的临界胶束浓度(CMC),并首次把荧光探针技术应用到硅/丙核壳乳液聚合反应的研究中.利用芘的I₁/I₃值,结合胶束微环境的极性变化规律和乳液聚合机理,探讨了乳化剂对聚合反应的影响.结果表明,荧光探针(芘)法可用于研究硅/丙乳液的聚合行为和确定乳化剂配比.通过粒径分析、透射电镜(TEM)对产品的结构进行了表征.     

Synthesis and characterization of fluorine‐containing polyacrylate latex with core–shell structure by UV‐initiated seeded emulsion polymerization

A core–shell fluorine‐containing polyacrylate emulsion was successfully prepared by UV‐initiated seeded emulsion polymerization in two stages in the presence of two photoinitiators. The water‐soluble photoinitiator for the core polymerization and the oil‐soluble photoinitiator was used for the shell polymerization. Both of the two stage polymerizations could be completed within 15 min and displayed a conversion above 94%. The emulsion and the films were characterized by Fourier transformed infrared spectrometry, transmission electron microscopy, dynamic light scattering, X‐ray photoelectron spectroscopy (XPS), contact angle (CA), and thermogravimetry analysis, respectively. The analysis results indicated that the fluorine‐containing latex particles had very small particle size (40 nm) with a core–shell structure and a narrow particle size distribution. XPS analysis revealed that a gradient concentration of fluorine excited in fluorine‐containing emulsion film from the film–air interface to the film–glass interface. In addition, the film formed from the fluorine‐containing emulsion exhibited not only higher thermal stability but also better hydrophobicity than that of the fluorine‐free emulsion. Copyright © 2010 John Wiley & Sons, Ltd.     

环氧硅氧烷对丙烯酸酯类无皂涂料性能的影响

无皂乳液涂料;环氧硅氧烷对丙烯酸酯类无皂涂料性能的影响     

Synthesis of pH and temperature sensitive, core-shell nano/microgels, by one pot, soap-free emulsion polymerization

The synthesis and properties of thermal/pH-sensitive core-shell copolymer nano/microgels were investigated. The crosslinked core consisted of N-isopropylacrylamide (NIPAAm) while the shell was stabilized by poly(ethylene glycol) methyl ether methacrylate (PEGMA) and 2-methacryloyloxybenzoic acid (2MBA) using a "one pot" soapless emulsion polymerization method. Monodisperse particles were produced with average hydrodynamic diameters ranging from 40 to 880 nm, as determined by dynamic light scattering (DLS) in water at 25°C, depending on the synthetic recipe used. The influence of PEGMA and 2MBA content on size and temperature transition at different pH values was studied. Zeta potential measurements and acid-base titration studies demonstrated almost complete incorporation of acid comonomer (2MBA) into the nano/microgels. Two different crosslinkers, a stable and an acid labile, were compared. The crosslinker used has a major influence on the size and charge density of the nano/microgels produced. Microscopic studies confirmed the core-shell morphology of the nano/microgels.     

Synthesis and surface properties of polyurethane modified by polysiloxane

A series of polyurethanes modified by polysiloxane (Si-PU) were synthesized based on 2,4-toluene diisocyanate (TDI), dihydroxybutyl-terminated polydimethylsiloxane (DHPDMS), polytetramethylene glycol (PTMG) and 1,4-butanediol (BDO). Fourier transform infrared spectroscopy analysis showed that DHPDMS had been incorporated into the polyurethane chains. With the increase of DHPDMS content, the water contact angle increased while the surface tension decreased. As the DHPDMS content increases above 5%, both the contact angle and the surface tension tend to approach a constant. The contact angle increases with increasing temperature, and it tends to approach a constant when the temperature is higher than 50°C. The result indicates that Si-PU exhibits good surface and mechanical properties when the DHPDMS content is 5%. __________ Translated from Polymer Materials Science and Engineering, 2007, 23(3): 47–50 [译自: 高分子科学与工程]     

SiO2@P（MMA/BA/3FMA）复合纳米粒子的制备及膜性能

通过溶胶-凝胶法与半连续种子乳液聚合法相结合,以正硅酸乙酯(TEOS)制备的纳米SiO2为核,以甲基丙烯酸甲酯(MMA)、丙烯酸丁酯(BA)和甲基丙烯酸三氟乙酯(3FMA)的共聚物P(MMA/BA/3FMA)为壳,合成了SiO2@P(MMA/BA/3FMA)核-壳结构纳米复合粒子.为防止纳米SiO2的团聚,提高其与共聚物的结合力,用乙烯基三甲氧基硅烷(VTMS)对纳米SiO2进行改性.通过红外光谱、透射电子显微镜、动态激光散射粒度仪、静态接触角测试仪、X射线光电子能谱分析和热重分析等表征了乳液结构及膜性能.结果表明,获得的复合纳米粒子呈现粒径分布为40～50 nm的核-壳结构球型颗粒.由于含氟官能团的迁移使得氟元素在膜-空气界面富集,有效降低了膜的表面自由能.当3FMA质量分数达到25%时,膜表面自由能达到最低值(23.13 mN/m).随着3FMA含量的增加,共聚物初始热分解温度由350℃提高到390℃.     

On the role of initiator in emulsion polymerization

The use of nonionic poly(ethylene glycol)-azo-initiators instead of ionic initiators in emulsion polymerizations offers interesting possibilities for modifying the colloidal and polymeric properties of polymer dispersions. Experimental results are presented for various kinds of anionic, cationic, and nonionic stabilizers as well as for peroxodisulfate initiators with different counter ions (ammonium and potassium). For example, in a styrene emulsion polymerization (with monomer to water mass ratio of 1:4 at a given concentration of 1% with respect to monomer mass of either an anionic or a cationic surfactant), the replacement of either peroxodisulfate or 2,2'-azobis(2-amidinopropane)dihydrochloride by a poly(ethylene glycol)-azo-initiator (with a poly(ethylene glycol) molecular weight of 200 g mol^-1) leads to particles with considerably smaller size, polymers with higher molecular weight, and latexes with higher viscosity.     

Amphiphilic hydrogel nanoparticles. Preparation, characterization, and preliminary assessment as new colloidal drug carriers

Inverse emulsion photopolymerization of acrylated poly(ethylene glycol)-bl-poly(propylene glycol)-bl-poly(ethylene glycol) and poly(ethylene glycol) was successfully employed to prepare stable, cross-linked, amphiphilic nanoparticles. Even at low emulsifier concentrations (2%) and high water-to-hexane weight ratios (35/65), the stability of the inverse emulsion allowed for the formation of well-defined colloidal material. Inverse emulsion characteristics and polymerization conditions could be controlled to vary the size of the nanoparticles between 50 and 500 nm. The presence of hydrophobic nanodomains within these otherwise hydrophilic nanoparticles was verified by using pyrene as a microenvironmentally sensitive probe. The hydrophobic poly(propylene glycol)-rich domains appear to be suitable for incorporation of hydrophobic drugs, encapsulating Doxorubicin up to 9.8% (w/w). We believe that the complex nano-architecture of these materials makes them a potentially interesting colloidal drug delivery carrier system and that the method should be useful for a number of amphiphilic macromolecular precursors.     

Synthesis and characterization of magnetic and non-magnetic core-shell polyepoxide micrometer-sized particles of narrow size distribution

Core polystyrene microspheres of narrow size distribution were prepared by dispersion polymerization of styrene in a mixture of ethanol and 2-methoxy ethanol. Uniform polyglycidyl methacrylate/polystyrene core-shell micrometer-sized particles were prepared by emulsion polymerization at 73 degrees C of glycidyl methacrylate in the presence of the core polystyrene microspheres. Core-shell particles with different properties (size, surface morphology and composition) have been prepared by changing various parameters belonging to the above seeded emulsion polymerization process, e.g., volumes of the monomer glycidyl methacrylate and the crosslinker monomer ethylene glycol dimethacrylate. Magnetic Fe(3)O(4)/polyglycidyl methacrylate/polystyrene micrometer-sized particles were prepared by coating the former core-shell particles with magnetite nanoparticles via a nucleation and growth mechanism. Characterization of the various particles has been accomplished by routine methods such as light microscopy, SEM, FTIR, BET and magnetic measurements.     

Preparation of temperature-sensitive polymer particles having different lower critical solution temperatures

Preparation of temperature-sensitive core-shell composite polymer particles was carried out by seeded emulsion copolymerization of dimethylaminoethyl methacrylate and ethylene glycol dimethacrylate with submicron-sized polystyrene seed particles as core. The lower critical solution temperature (LCST) of the core-shell composite was about 35°C, while the LCST could be controlled toward higher or lower temperatures by copolymerizing the shell layer with hydrophilic/hydrophobic vinyl comonomer.     

氨基硅油扩链改性水性聚氨酯的研究

通过将由甲苯二异氰酸酯与聚四氢呋喃,二羟甲基丙酸反应制得的聚氨酯预聚体在低浓度氨基硅油的水乳液中扩链,合成了一种硅氧烷改性的聚氨酯水乳液,并用傅立叶红外光谱,ＥＳＣＡ能谱,接触角仪,电子拉力试验机,吸水率测定及乳液稳定性测试对其进行研究。     

Rheology of double emulsions

New equations for the viscosity of concentrated double emulsions of core-shell droplets are developed using a differential scheme. The equations developed in the paper predict the relative viscosity (eta(r)) of double emulsions to be a function of five variables: a/b (ratio of core drop radius to shell outer radius), lambda(21) (ratio of shell liquid viscosity to external continuous phase viscosity), lambda(32) (ratio of core liquid viscosity to shell liquid viscosity), phi(DE) (volume fraction of core-shell droplets in double emulsion), and phi(m)(DE) (the maximum packing volume fraction of un-deformed core-shell droplets in double emulsion). Two sets of experimental data are obtained on the rheology of O/W/O (oil-in-water-in-oil) double emulsions. The data are compared with the predictions of the proposed equations. The proposed equations describe the experimental viscosity data of double emulsions reasonably well.     

种子乳胶粒表面修饰法制备核壳结构PSt/TiO_2复合微球

首先采用无皂乳液聚合法合成了表面带负电荷、粒径为360 nm的单分散聚苯乙烯(PSt)乳液,并利用聚乙烯亚胺(PEI)在25℃下对PSt乳胶粒表面进行修饰,得到了表面带有正电荷的PSt种子乳液;然后以乙醇和水的混合物为反应介质,采用种子乳液加入法,使钛酸正丁酯(TBT)在修饰后的乳胶粒表面进行水解与缩合,制备出了核壳结构PSt/TiO2复合微球,利用电镜对复合微球的结构形态进行了表征.结果表明,PSt乳液改性时体系的zeta电位随着PEI用量的增加而升高,当PEI用量为PSt聚合物重量的15%时,体系的zeta电位从原来的-40.3 mV升高到了38.3 mV,达到对PSt乳胶粒表面改性的最佳值;在制备PSt/TiO2复合微球时,TiO2包覆量随着反应时间的延长而增加,反应7 h时达到90.2%的最大值;随介质中水含量的增加,吸附到复合微球表面上的TiO2纳米颗粒逐渐减少,复合微球表面逐渐变得光滑,当EtOH/H2O质量比为100/6.0时,得到结构均一、壳层厚度为29 nm的核壳结构PSt/TiO2复合微球.     

Synthesis of polystyrene/poly[2-(dimethylamino)ethyl methacrylate-stat-ethylene glycol dimethacrylate] core-shell latex particles by seeded emulsion polymerization and their application as stimulus-responsive particulate emulsifiers for oil-in-water emulsions

Surfactant-stabilized polystyrene (PS) latex particles with a mean hydrodynamic diameter of 155 nm were prepared by aqueous emulsion polymerization using 2,2'-azobis(2-amidinopropane) hydrochloride as a cationic radical initiator. Seeded aqueous emulsion copolymerizations of 2-(dimethylamino)ethyl methacrylate (DMA) and ethylene glycol dimethacrylate (EGDMA) were conducted in the presence of these PS particles to produce two batches of colloidally stable core-shell latex particles, in which the shell comprised a cross-linked P(DMA-stat-EGDMA) overlayer. Both the PS and PS/P(DMA-stat-EGDMA) latexes were characterized in terms of their particle size, morphology, and composition using dynamic light scattering, electron microscopy, and FT-IR spectroscopy, respectively. Using the PS/P(DMA-stat-EGDMA) latex particles as a pH-responsive particulate ('Pickering'-type) emulsifier, polydisperse n-dodecane-in-water emulsions were prepared at pH 8 that could be partially broken (demulsified) on lowering the solution pH to 3. These emulsions were characterized in terms of their emulsion type, mean droplet diameter, and morphology using electrical conductivity and Mastersizer measurements, optical microscopy, and scanning electron microscopy (using critical point drying for sample preparation).     

DESIGN AND CONTROL OF SOAP-FREE HYDROPHILIC-HYDROPHOBIC CORE-SHELL LATEX PARTICLES WITH HIGH CARBOXYL CONTENT IN THE CORE OF THE PARTICLES

Soap-free hydrophilic-hydrophobic core-shell latex particles with high carboxyl content in the core of the particles were synthesized via the seeded emulsion polymerization using methyl methacrylate(MMA),butyl acrylate(BA), methacrylic acid(MAA),styrene(St)and ethylene glycol dimethacrylate(EGDMA)as monomers,and the influences of MMA content used in the core preparation on polymerization,particle size and morphology were investigated by transmission electron microscopy,dynamic light scattering and conductometric titration.The results showed that the seeded emulsion polymerization could be carried out smoothly using "starved monomer feeding process" when MAA content in the core preparation was equal to or less than 24 wt%,and the encapsulating efficiency of the hydrophilic P(MMA-BA-MAAEGDMA) core with the hydrophobic PSt shell decreased with the increase in MAA content.When an interlayer of P(MMAMAA -St)with moderate polarity was inserted between the P(MMA-BA-MAA-EGDMA)core and the PSt shell,well designed soap-free hydrophilic-hydrophobic core-shell latex particles with 24 wt%MAA content in the core preparation were obtained.