空气中大气压下均匀辉光放电的可能性

利用介质阻挡电极结构,对101325×105Pa气压下空气间隙中的放电进行了实验研究,数值模拟计算了实验条件下电子雪崩的发展过程.结果表明:对于长度不大于2mm的空气间隙,可能实现辉光放电.对于长度不小于5mm的空气间隙,如果不能设法降低放电场强,放电必然是流注形式,不可能实现辉光放电.另外,实验结果未能验证“离子捕获”机理降低放电场强而实现辉光放电的正确性 关键词： 大气压辉光放电 电子雪崩 流注     

大气压介质阻挡放电的光谱研究

使用水电极介质阻挡放电装置,分别在大气压空气和氦气中实现了稳定的高气压放电。通过水电极观察两种气体的放电,发现大气压空气中放电为空间随机分布的微放电丝,等离子体是不均匀的,而在氦气中放电没有微放电丝,空间分布比较均匀。比较而言,这种均匀放电产生的等离子体具有更广泛的工业应用前景。对两种气体中放电的电流波形进行了比较,发现空气中放电的电流脉冲在时间上是随机出现的而氦气中放电的电流脉冲在时间上具有周期性,并且空气中放电脉冲宽度约为几十ns而氦气中放电的电流持续时间较长,脉冲宽度大约为1μs。文章还对两种气体中介质阻挡放电发射光谱进行了研究,结果表明大气压氦气中均匀放电的N+₂(B2Σ+_u→X2Σ+_g)谱线391.4nm很强而在大气压空气放电中此光谱线很弱。这些研究结果对高气压条件下均匀放电的实现和大气压辉光放电的工业应用具有重要意义。     

实验研究大气压多脉冲辉光放电的模式和机理

采用稍不平行电极进行大气压He气介质阻挡多脉冲辉光放电实验,通过增强电子耦合器件相机短时曝光照片,研究大气压多脉冲辉光放电在不同时刻的放电模式.通过气隙放电电流、表面电荷计算,理论分析了表面电荷、空间电荷、外加电压与气隙电场强度的关系,研究大气压辉光放电形成多脉冲的机理.实验结果表明,放电首先在间隙稍窄的电极左端开始;在第一个脉冲电流峰值,电极右端也开始放电;第一个电流脉冲经历了Townsend放电到辉光放电的过程;电流脉冲之间的时间内,间隙一直维持着微弱的辉光放电;随后的每个电流脉冲均是辉光放电.理论分析表明,大气压辉光放电的多个电流脉冲是表面电荷、空间电荷与外加电压共同演化的结果;除放电伊始出现Townsend放电外,同一半周期内的放电电流脉冲中不会再出现Townsend放电. 关键词： 介质阻挡放电 增强电子耦合器件 大气压辉光放电 多脉冲     

High speed imaging of nanosecond-pulse dielectric barrier discharge in atmospheric air

使用上升沿40 ns、脉宽70 ns的重复频率单极性纳秒脉冲电源,采用双水电极结构产生大气压空气中介质阻挡放电.测量了纳秒脉冲下介质阻挡电压和电流,并获得长曝光时间和ns级曝光时间的放电特性,采用曝光时间为2 ns的高速摄影拍摄放电发展过程.结果表明:大气压空气中,水电极结构纳秒脉冲介质阻挡放电能够产生稳定均匀的放电等离子体,且存在二次放电.高速摄影对放电发展过程的拍摄结果表明:放电首先由电极中部开始发展,径向扩展至整个电极范围.     

空气中纳秒脉冲介质阻挡放电高速摄影

使用上升沿40 ns、脉宽70 ns的重复频率单极性纳秒脉冲电源,采用双水电极结构产生大气压空气中介质阻挡放电。测量了纳秒脉冲下介质阻挡电压和电流,并获得长曝光时间和ns级曝光时间的放电特性,采用曝光时间为2 ns的高速摄影拍摄放电发展过程。结果表明:大气压空气中,水电极结构纳秒脉冲介质阻挡放电能够产生稳定均匀的放电等离子体,且存在二次放电。高速摄影对放电发展过程的拍摄结果表明:放电首先由电极中部开始发展,径向扩展至整个电极范围。     

�����н�����-�����ѹ�Թ�ŵ�

空气中的大气压辉光放电通常因放电易过渡到火花状态而难以产生。在静态大气压空气针-板等离子体发生器中，采用阻容耦合负反馈方法控制等离子体放电发展过程，成功地抑制了辉光放电向火花放电的过渡，产生了稳定的交流辉光放电。研究了电压、电极间距等参数变化对放电的影响。     

实验研究大气压多脉冲辉光放电的模式和机理

采用稍不平行电极进行大气压He气介质阻挡多脉冲辉光放电实验,通过增强电子耦合器件相机短时曝光照片,研究大气压多脉冲辉光放电在不同时刻的放电模式.通过气隙放电电流、表面电荷计算,理论分析了表面电荷、空间电荷、外加电压与气隙电场强度的关系,研究大气压辉光放电形成多脉冲的机理.实验结果表明,放电首先在间隙稍窄的电极左端开始;在第一个脉冲电流峰值,电极右端也开始放电;第一个电流脉冲经历了Townsend放电到辉光放电的过程;电流脉冲之间的时间内,间隙一直维持着微弱的辉光放电;随后的每个电流脉冲均是辉光放电.理论分析表明,大气压辉光放电的多个电流脉冲是表面电荷、空间电荷与外加电压共同演化的结果;除放电伊始出现Townsend放电外,同一半周期内的放电电流脉冲中不会再出现Townsend放电.     

大气压辉光放电研究现状及应用前景

大气压辉光放电由于均匀性好、能量效率高并且不需要真空系统，正日益受到人们重视和研究．文章综述了大气压辉光放电的研究进展，包括实验条件、放电特征、放电机理以及最新的诊断方法，还介绍它在薄膜沉积、材料表面改性、污染物质的消毒去污等方面的应用前景．     

石英管对空气中锥-板结构纳秒脉冲放电的影响

报道了石英管对大气压下空气中锥-板电极结构纳秒脉冲放电的影响实验研究.实验过程中发现将石英管纵向移动位置,放电会出现四种明显不同的形貌状态,对其机理进行了初步的探讨.利用发射光谱诊断了其转动和振动温度(分别为295和2200 K),表明该等离子体具有高度非平衡度.还进一步提出大气压下空气中产生类辉光放电的有效途径. 关键词： 纳秒脉冲放电 空气 纵向介质 非平衡等离子体     

介质阻挡放电丝模式和均匀模式转化的特性

利用水电极介质阻挡放电装置,采用电学方法和发射光谱,研究了空气中介质阻挡放电从微放电丝模式向均匀放电模式转化的过程. 结果表明,大气压下增大外加电压或者电压一定减小气压,放电都能够从微放电丝模式过渡到均匀模式. 高气压下放电为流光击穿而低气压下为辉光放电. 利用放电发射光谱,研究了高能电子比例随实验参数的变化. 结果表明气压减小时高能电子比例增大,电压增加时高能电子减少. 利用壁电荷理论对以上实验结果进行了定性分析. 结果对介质阻挡均匀放电的深入研究具有重要价值. 关键词： 介质阻挡放电 光学发射谱 微放电丝 均匀放电模式     

大气压氩气射流等离子体的光谱特性研究

等离子体喷枪是一种重要的等离子体源,已成为近几年低温等离子体研究的一个重要课题。本文利用钨针-钨丝网电极制作了直流喷枪装置,在大气压空气中产生了稳定的等离子体羽,并采用发射光谱的方法,对等离子体羽的等离子体参数进行了研究。在钨针电极与钨丝网电极之间放出耀眼的白光,钨丝网电极出口的气流下游有火苗形状的等离子体羽喷出。在电压保持不变的条件下(13.5 kV),等离子体羽长度随气体流量增加而增大;在气体流量保持不变的条件下(10 L·min-1),羽长度随外加电压的增大而增大。在气体流量一定的条件下,放电电压和放电电流呈反比例关系,即电压随着电流的增大而减小,说明放电属于辉光放电。采集了该喷枪在300～800 nm范围内的放电发射光谱,通过玻尔兹曼方法对放电等离子体电子激发温度进行了测量。结果表明,电子的激发温度随外加电压的增大而降低,随着工作气体流量的减小而升高。利用放电的基本理论对上述现象做了解释。这些研究结果对大气压均匀放电等离子体源的研制和工业应用具有重要意义。     

Influence of wire mesh electrodes on the volume and surface characteristics of dielectric barrier discharge of atmospheric pressure helium

The dielectric barrier discharge of helium in a 6 mm gap at atmospheric pressure was studied. In this paper, the influence of electric field distribution on the uniformity of DBD is analyzed theoretically and verified by experiments. The experimental results show that the mesh electrode produces a local enhancement effect by affecting the electric field and then produces corona discharge, which provides seed electrons for the subsequent discharge process. The effects of mesh diameter and size on discharge uniformity and stability are analyzed, the electrode structure parameters are optimized, the method of a segmented electrode is proposed, and the discharge process and charge distribution are studied. The electrical diagnosis results of plasma technology show that the segmented mesh electrode reduces the breakdown voltage of DBD and increases the charge deposition.     

Calculation of time dependence of the electrode surface temperature in the cathode spot of atmospheric pressure normal glow discharge

Non-stationary heat transfer in the volume of the electrode with the cathode spot of atmospheric pressure normal glow discharge on its surface is calculated in case the spot radius is much less than the electrode dimensions. A system of equations describing variation of the temperature in the spot and the discharge cathode sheath parameters after discharge ignition is formulated, and the time dependence of the electrode temperature in the spot for discharge in helium is found. It is shown that within a short time fast heating of the electrode surface in the spot proceeds and then its temperature is slowly approaching the equilibrium value.     

Development of a new atmospheric pressure cold plasma jet generator and application in sterilization

This paper reports that a new plasma generator at atmospheric pressure, which is composed of two homocentric cylindrical all-metal tubes, successfully generates a cold plasma jet. The inside tube electrode is connected to ground, the outside tube electrode is connected to a high-voltage power supply, and a dielectric layer is covered on the outside tube electrode. When the reactor is operated by low-frequency (6 kHz--20 kHz) AC supply in atmospheric pressure and argon is steadily fed as a discharge gas through inside tube electrode, a cold plasma jet is blown out into air and the plasma gas temperature is only 25--30℃. The electric character of the discharge is studied by using digital real-time oscilloscope (TDS 200-Series), and the discharge is capacitive. Preliminary results are presented on the decontamination of E.colis bacteria and Bacillus subtilis bacteria by this plasma jet, and an optical emission analysis of the plasma jet is presented in this paper. The ozone concentration generated by the plasma jet is 1.0×10¹⁶cm^-3 which is acquired by using the ultraviolet absorption spectroscopy.     

Homogeneous electrical explosion of tungsten wire in vacuum

Experimental results on Joule energy deposition upon initiation of a fast electrical explosion of 16-μm tungsten wire in vacuum at current densities of more than 10⁸ A/cm² are reported. We have found that explosion with a fast current rise time (～170 A/ns into a short) results in homogeneous and enhanced deposition of electrical energy into the tungsten before surface flashover. The maximum tungsten wire resistivity reaches a value of up to ～185 μΩ cm before surface flashover that significantly exceeds the melting boundary and corresponds to a temperature of ～1 eV. The highest values for light radiation and expansion velocity of wire ～1 km/s were observed for the fast explosion. For the explosion mode with a slower current rise time (～22 A/ns into a short), we observed the existence of an “energy deposition barrier” for tungsten wire. In the slow explosion mode, the current is reconnected to the surface shunting discharge before melting. The maximum tungsten wire resistivity in this case reaches the value of ～120 μΩ cm, which is less than indicative of melting. Also, the energy deposition along the wire is strongly inhomogeneous, and wire is disintegrated into parts. We attribute the early reconnection of the current to the surface discharge for the slow explosion to high electron emission from the wire surface, which starts before melting.     

Effect of catalysts on dc corona discharge poisoning

The processes of ozone generation in non-thermal plasma produced by an electrical discharge in air at atmospheric pressure are burdened by the presence of nitrogen oxides, which on the one hand contribute to ozone generation and on the other hand are responsible for unpleasant discharge poisoning. The term discharge poisoning refers to the situation when the discharge ozone formation completely breaks down. Discharge poisoning can be affected by placing a catalyst in the discharge chamber. For the dc hollow needle to mesh corona discharge enhanced by the flow of air through the needle electrode we studied the effect of titanium dioxide TiO₂, ZSM-5 zeolite or Cu⁺⁺ZSM-5 zeolite on discharge poisoning by monitoring the ozone, nitrogen monoxide and nitrogen dioxide discharge production. We found that placing globules of any of these catalysts on the mesh decreases the energy density of the onset of discharge poisoning, and this energy density is smallest for a discharge with globules of a TiO₂ on the mesh.     

Uniformity analysis of dielectric barrier discharge (DBD) processed polyethylene terephthalate (PET) surface

A dielectric barrier discharge (DBD) plasma, operating in air at atmospheric pressure, has been used to induce changes in the surface properties of polyethylene terephthalate (PET) films. The effects that the key DBD operating parameters: discharge power, processing speed, processing duration, and electrode configurations, have on producing wettability changes in the PET surface region have been investigated. The approach taken involves the application of an Taguchi experimental design and robust analysis methodology. The various data sets obtained from these analyses have been used to studies the effect of the operating parameters on the surface uniformity and efficiency of the said treatment.In general, the results obtained indicate that DBD plasma processing is an effective method for the controlled surface modification of PET. Relatively short exposures to the atmospheric pressure discharge produces significant wettability changes at the polymer film surface, as indicted by pronounced reductions in the water contact angle measured. It was observed that the wettability of the resultant surface shows no significant differences in respect to orientation parallel (L-direction) or perpendicular (T-direction) to the electrode long axis. However, there was significant differences between the data obtained from these two orientations. Analysis of the role of each of the operating parameters concerned shows that they have a selective effectiveness with respect to resultant surface modification in terms of uniformity of modification and wettability. The number of treatment cycles and the electrode configuration used were found to have the most significant effects on the homogeneity of the resultant PET surface changes in L- and T-orientation, respectively. On the other hand, the applied power showed no significant role in this regard. The number of treatment cycles was found to be the dominant factor (at significance level of 0.05) in respect of water contact angle changes at the processed PET surface in both orientations. The driven metal electrodes (stainless steel or aluminium) were apparently superior to the driven dielectric electrode (ceramic or quartz) configurations. The grounded electrode in each case was a silicon rubber-covered aluminium plate (see later). The nature and scale of the surface changes that originate from the various processing conditions employed have been considered so as to determine the optimum treatment conditions in respect of processing outcomes, properties and any orientation dependence. Thus, it was revealed that higher processing speeds and longer processing durations are key for uniformity along the electrode axial orientation, while lower processing speeds and short exposure durations are key considerations, in the corresponding perpendicular orientation. In general, longer processing durations (low processing speeds and a high number of treatment cycles) and higher plasma powers induced greater changes in the surface wettability of the PET, as demonstrated by the observed water contact angles. This behaviour is taken to indicate that different combinations of DBD operating parameters and electrodes produce discharge conditions that can result in different plasma chemical processes in respect of uniformity, treatment efficiency and orientation dependence.     

DC corona ozone generation enhanced by TiO<Subscript>2</Subscript> photocatalyst

Non-thermal electrical discharges, such as corona discharge are apart of the source of ozone, charged, and excited species and acoustic noise also the source of electromagnetic radiation of different wavelengths. The important component of this radiation from the standpoint of photocatalyst activation is the ultraviolet radiation. We studied the role of UV radiation on corona discharge ozone production by placing the titanium dioxide photocatalyst into the discharge region. We used hollow needle to mesh DC corona discharge at atmospheric pressure with TiO₂ globules on the mesh. The discharge was enhanced by the flow of air through the needle. We found that for the needle biased negatively addition of TiO₂ photocatalyst on the mesh electrode drastically increases discharge ozone production as well as the ozone production yield. These quantities are also influenced by the mass of the used photocatalyst and its distribution in the discharge chamber.     

Coaxial rf atmospheric pressure dielectric barrier air-helium plasma characteristics

The electrical and optical characteristics of a coaxial rf atmospheric pressure dielectric barrier discharge (DBD) with one electrode covered with glass and with helium in air were investigated. Optical measurements with an intensified charge coupled device (ICCD) camera combined with the voltage and power vs. current data provided identification of the α to γ mode transitions. The coaxial design allowed operation with very low power density plasmas (0.18 W/cm³) and a much larger plasma size (13 mm) than the parallel plate designs.     

Effect of dielectric barrier discharge on semiconductor Si electrode surface

Electrode materials and shapes affected the discharge modes. Meanwhile, the discharge has influence upon electrode surface. In order to study the effect of discharge on semiconductor electrode, the experiments were carried out using single crystal Si wafer as high voltage electrode of atmospheric pressure dielectric barrier discharge in air. The effects of dielectric barrier discharge on Si electrode surface are analyzed by means of field emission scanning electron microscope (FESEM) and X-ray photoelectron spectroscopy (XPS). The results show that surface roughness and oxidation increase with discharge time, while surface nitridation is not observed on Si electrode surface. It is different from Cu electrode. The difference is due to different chemical reactions between electrode surface and air plasma but could also be ascribed to the different analysis techniques used.