Straight and thin ZnO nanorods: hectogram-scale synthesis at low temperature and cathodoluminescence

A novel seed-assisted chemical reaction at 95 degrees C has been employed to synthesize uniform, straight, thin, and single-crystalline ZnO nanorods on a hectogram scale. The molar ratio of ZnO seed and zinc source plays a critical role in the preparation of thin ZnO nanorods. At a low molar ratio of ZnO seed and zinc source, javelin-like ZnO nanorods consisting of thin ZnO nanorods with a diameter of 100 nm and thick ZnO nanorods with a diameter of 200 nm have been obtained. In contrast, straight ZnO nanorods with a diameter of about 20 nm have been prepared. Dispersants such as poly(vinyl alcohol) act spatial obstructors to control the length of ZnO nanorods. The morphology, structure, and optical property of the ZnO nanostructures prepared under different conditions have been characterized by transmission electron microscopy, field emission scanning electron microscopy, X-ray powder diffraction, high-resolution transmission electron microscopy, and cathodoluminescence. The formation mechanisms for the synthesized nanostructures with different morphologies have been phenomenologically presented.     

Photocatalytic Activity of Nanocomposites of ZnO and Multi-Walled Carbon Nanotubes for Dye Degradation

Nanocomposites of ZnO and multi-walled carbon nanotubes (MWNTs) were prepared via electrostatic interaction and in situ hydrothermal synthesis approaches. The ZnO/MWNTs nanocomposites display relatively higher photocatalytic activity than ZnO nanoparticles for the degradation of Rhodamine B. Therein, MWNTs, acting as a photogenerated electron acceptor, retard the recombination of photoinduced electron and hole. The experimental results show that the photocatalytic activity of the ZnO/MWNTs nanocomposites strongly depends on the synthetic route, which is probably due to the difference of surface states resulted from the different preparation processes.     

Synthesis and synchrotron light-induced luminescence of ZnO nanostructures: nanowires, nanoneedles, nanoflowers, and tubular whiskers

ZnO nanostructures, including single-crystal nanowires, nanoneedles, nanoflowers, and tubular whiskers, have been fabricated at a modestly low temperature of 550 degrees C via the oxidation of metallic Zn powder without a metal catalyst. Specific ZnO nanostructures can be obtained at a specific temperature zone in the furnace depending on the temperature and the pressure of oxygen. Scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), and X-ray diffraction (XRD) studies show that ZnO nanostructures thus prepared are single crystals with a wurtzite structure. X-ray excited optical luminescence (XEOL) from the ZnO nanostructures show noticeable morphology-dependent luminescence. Specifically, ZnO nanowires of around 15 nm in diameter emit the strongest green light. The morphology of these nanostructures, their XEOL, and the implication of the results will be discussed.     

ZnO Nanobelts and Hollow Microspheres Grown on Cu Foil

ZnO nanobelts, hollow microspheres, and urchins have been prepared on copper foil via a simply low temperature evaporation route. The microstructure, morphologies, and photolu-minescence of the ZnO nanostructures were studied with X-ray diffraction, Raman spectra, scanning electron microscopy and photoluminescence spectra. The width of the nanobelts was about 500 nm and the length was longer than 10μm. The diameter of the hollow microspheres was between 5 and 10μm. A possible growth mechanism of the nanobelts, microspheres and urchins was proposed. The photoluminescence spectrum exhibited strong deep level energy emissions and a weak near band edge emission. These ZnO nanostructures on a copper substrate have the advantages of naturally good adhesion and electrical connection between the ZnO nanostructures and the conductive substrate.     

Chemical stability of ZnO nanostructures in simulated physiological environments and its application in determining polar directions

The in vitro chemical stability and etching of ZnO nanostructures in simulated physiological solution (SPS) were studied using electron microscopy. Calcium hydrogen phosphate thin layers were observed to be uniformly deposited on the surfaces of ZnO nanomaterials in SPS. Electron diffraction and high-resolution transmission electron microscopy revealed that the calcium hydrogen phosphate layers were amorphous and had excellent interfacial contact with the nanocrystals. ZnO nanostructures fabricated by thermal evaporation were found to survive much longer in SPS than those fabricated using a hydrothermal solution method. The shapes of the voids formed in the ZnO nanostructures by the etching in SPS can be used to deduce the polar directions of ZnO nanostructures.     

聚苯乙炔衍生物对碳纳米管的溶解作用与表面巯基官能化

设计合成了带巯基的聚苯乙炔衍生物,在产物的红外光谱上,3312和776 cm-1处炔氢特征吸收与2106 cm-1处碳碳三键的特征红外吸收消失;在产物的1H-NMR谱上,对应单体上炔氢的化学位移(δ=3.0)消失而对应共轭烯烃的化学位移(δ=6.4)出现;这些谱学特征变化证明了聚合反应的发生.巯基官能化的聚苯乙炔不仅能够发挥聚苯乙炔衍生物对碳纳米管的增溶作用,而且具有将碳纳米管表面巯基功能化的特殊性能.通过巯基与ZnO之间的强相互作用,ZnO纳米粒子被组装到巯基官能化的聚苯乙炔/碳纳米管杂化结构的外壳.本研究提供了制备新的多元复合纳米结构材料的方法.     

Hierarchical saw-like ZnO nanobelt/ZnS nanowire heterostructures induced by polar surfaces

Saw-like nanostructures composed of single-crystalline ZnO nanobelts and single-crystalline ZnS nanowires have been successfully synthesized by a vapor-solid process. Several techniques, including scanning electron microscope, transmission electron microscopy, and photoluminescence spectroscopy, were used to investigate the structures, morphology, and photoluminescence properties of the products. Due to the similar crystal habits of wurtzite ZnO and ZnS with chemically active Zn-terminated (0001) and chemically inactive O-terminated (or S-terminated) (000) polar surfaces, hierarchical saw-like nanostructures were considered to be formed by the initiation of a chemically active Zn-terminated ZnO (0001) polar surface. Photoluminescence properties of the heterostructures, different from pure ZnO nanobelts or ZnS nanowires, were also studied at room temperature.     

Controlled modification of multi-walled carbon nanotubes with CuO,Cu2O and Cu nanoparticles

Multi-walled carbon nanotubes (MWNTs) have been successfully modified with CuO, Cu₂O and Cu nanoparticles via a simple method, and the calcination temperature, the amount of NH₃·H₂O and soaking time play critical roles in controlling the final products. The modified MWNTs have been characterized by X-ray diffraction, infrared spectrum, scanning electron and transmission electron microscopies. Optical absorption of the obtained products has also been investigated, and the quantum confinement effect was illustrated in the absorption spectra.     

不同形貌ZnO纳米结构的电子显微分析

控制实验合成条件,利用溶胶-凝胶法和化学溶液生长法制备出不同形貌的ZnO纳米结构。采用X射线衍射仪(XRD)、扫描电子显微镜( SEM) 以及透射电子显微镜(TEM)等多种测试手段对ZnO纳米结构的微观形态及晶相进行了分析。结果表明:3种ZnO纳米结构形貌虽不同,但均具有Z nO六方纤锌矿晶相结构。ZnO纳米棒和花状ZnO纳米结构为单晶,生长方向均沿(0001)方向。ZnO纳米球则为多晶。     

Ultra-sensitive hydrazine chemical sensor based on high-aspect-ratio ZnO nanowires

High-aspect-ratio ZnO nanowires based ultra-sensitive hydrazine amperometric sensor has been fabricated which showed a high and reproducible sensitivity of 12.76 μA cm⁻² nM⁻¹, detection limit, based on S/N ratio, 84.7 nM, response time less than 5 s, linear range from 500 to 1200 nM and correlation coefficient of R = 0.9989. This is the first report in which such a very high-sensitivity and low detection limit has been achieved for the hydrazine sensors by using ZnO nanostructures modified electrodes. Therefore, this work opens a way to utilize simply grown ZnO nanostructures as an efficient electron mediator to fabricate efficient hydrazine sensors.     

Recent advances in ZnO nanostructures and thin films for biosensor applications: Review

Biosensors have shown great potential for health care and environmental monitoring. The performance of biosensors depends on their components, among which the matrix material, i.e., the layer between the recognition layer of biomolecule and transducer, plays a crucial role in defining the stability, sensitivity and shelf-life of a biosensor. Recently, zinc oxide (ZnO) nanostructures and thin films have attracted much interest as materials for biosensors due to their biocompatibility, chemical stability, high isoelectric point, electrochemical activity, high electron mobility, ease of synthesis by diverse methods and high surface-to-volume ratio. ZnO nanostructures have shown the binding of biomolecules in desired orientations with improved conformation and high biological activity, resulting in enhanced sensing characteristics. Furthermore, compatibility with complementary metal oxide semiconductor technology for constructing integrated circuits makes ZnO nanostructures suitable candidate for future small integrated biosensor devices. This review highlights recent advances in various approaches towards synthesis of ZnO nanostructures and thin films and their applications in biosensor technology.     

Site-specific nucleation and growth kinetics in hierarchical nanosyntheses of branched ZnO crystallites

Here we report a site-specific sequential nucleation and growth route to the systematic building of hierarchical, complex, and oriented ZnO micro/nanostructures in solution nanosynthesis. Structures and morphologies of the products were confirmed by results from X-ray diffraction and scanning electron microscopy studies. The organic structure-directing agents (SDAs), diaminopropane and citrate, are found to play different roles in controlling the evolution of these new morphologies. Through the selective adsorptions of SDAs on different crystal facets of the primary ZnO rods, we have alternated the hierarchical growth of secondary and tertiary new complex nanostructures. Roles of the SDA concentration, nucleation time, and growth kinetics in the solution hierarchical ZnO nanosyntheses have all been systematically investigated.     

A general electrochemical approach to deposition of metal hydroxide/oxide nanostructures onto carbon nanotubes

This communication describes a new and relatively general electrochemical approach to the deposition of transition metal hydroxide/oxide nanostructures onto multi-walled carbon nanotubes (MWNTs) based on the precipitation of metal hydroxide/oxide nanostructures onto MWNTs by increasing the local pH values at the electrode/electrolyte interface induced by the proton-consuming electrochemical reduction of hydrogen peroxide (H₂O₂). The results obtained with cyclic voltammetry, scanning electron microscopy, and X-ray photoelectron spectroscopy of the synthetic nanocomposites substantially suggest the deposition of the metal hydroxides/oxides onto MWNTs induced by the electrochemical reduction of H₂O₂. This study essentially offers a facile but effective and relatively general electrochemical approach to the synthesis of the nanocomposites consisting of metal hydroxides/oxides and MWNTs.     

Morphology-controlled synthesis of ZnO nanostructures by a simple round-to-round metal vapor deposition route

One-dimensional ZnO nanostructures with different morphologies have been successfully synthesized through a simple round-to-round metal vapor deposition route at 550 degrees C with a zinc powder covered indium film as the source material. The structures and morphologies of the products were characterized in detail by using X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. Studies found that the morphology of the products can be easily tuned from one experimental round to another. Possible growth mechanisms for the formation of one-dimensional ZnO nanostructures with different morphologies are discussed. Photoluminescence studies show that there are sharp UV emission and broad defect-related green emissions for the products obtained in all experimental rounds. Relative intensity of the UV emission to defect-related emissions gradually increased from one experimental round to another.     

海藻酸锌纤维热降解法制备氧化锌纳米结构

采用天然高分子海藻酸钠为原料, 以氯化锌水溶液为凝固浴, 通过湿法纺丝技术成功制备了海藻酸锌(Alg-Zn)纤维.通过在空气中不同温度下对所得海藻酸锌纤维进行热处理, 得到了多种ZnO纳米结构. 利用热失重分析(TG)、X射线衍射(XRD)、电子能量损失谱(EELS)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段对产物的组成、形貌和微观结构进行了详细表征. 结果表明, 焙烧温度和时间对所得ZnO纳米结构的尺寸和形貌具有重要影响; 800 ℃下热处理24 h以上可以得到直径约为120 nm的ZnO纳米棒. 通过仔细考察不同热处理时间得到的ZnO纳米结构, 提出了在焙烧条件下ZnO纳米棒的生长机理.     

Fabrication of 3D rotor-like ZnO nanostructure from 1D ZnO nanorods and their morphology dependent photoluminescence property

A facile and eco-friendly sonochemical route to fabricate well-defined dentritic (rotor-like) ZnO nanostructures from 1D ZnO nanorods without alloying elements, templates and surfactants has been reported. Phase and structural analysis has been carried out by X-ray diffraction (XRD) and Fourier Transform Infra-Red (FTIR) spectroscopy, showed the formation of hexagonal wurtzite structure of ZnO. Scanning electron microscopic (SEM) study showed the formation of rotor-like ZnO nanostructure having a central core which is surrounded by side branches nanocones. Transmission electron microscopic (TEM) study showed that these nanocones grow along [0001] direction on the six {01–10} planes of central core ZnO nanorods. A plausible formation mechanism of rotor-like ZnO nanostructures was studied by SEM which indicates that the size and morphology of side branches can be controlled by adjusting the concentration of OH^? ions and time duration of growth. The photoluminescence (PL) spectrum of the synthesized rotor-like ZnO nanostructures exhibited a weak ultraviolet emission at 400 nm and a strong green emission at 532 nm recorded at room temperature. The influence of morphology on the origin of green emission was discussed in detail. The results suggested a positive relationship among polar plane, oxygen vacancy and green emission.     

Template-free fabrication of hexagonal ZnO microprism with an interior space

Well-faceted hexagonal ZnO microprisms with regular interior space have been successfully prepared by a template-free hydrothermal synthetic route. The morphologies of the products depend on the experimental conditions such as the solvent, the concentration of ammonia aqueous solution, and the reaction temperature. Through manipulation of the aging time, the as-prepared ZnO can be controlled as a monodispersed hexagonal twinning solid or as hollow microprisms. Moreover, the evolution process of the hollow ZnO nanoarchitecture after reaction for 2, 6, 12, and 24 h has been investigated by field emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). A possible growth mechanism has also been proposed and discussed. Furthermore, the photoluminescence (PL) measurement exhibits the unique emitting characteristic of hollow ZnO nanostructures.     

Investigation of the dynamics of radiolytic formation of ZnO nanostructured materials by pulse radiolysis

ZnO nanostructures have been synthesized by radiolytic methods. A Cobalt-60 γ-source and a 7 MeV linear electron accelerator (LINAC) was used for the radiolysis experiments. Reducing agent like hydrated electron (e_aq⁻), which is produced in radiolysis of water, was used to synthesize ZnO nanostructure materials from zinc salt. 1 M tert-butanol was used to quench the primary oxidizing radical like hydroxyl radical (OH) radiolytic water solution. Doses of about 80–130 kGy were used to perform radiolysis experiments in the present investigation. Time-resolved pulse radiolysis has been used to monitor the transient species involved in the formation of ZnO nanostructures by monitoring at different wavelengths. A scheme for the formation of the ZnO nanostructured materials by the radiolytic method has been described. The formation of ZnO nanostructures was confirmed by X-ray diffraction (XRD) measurements. Dynamic light scattering (DLS) measurements indicated that the size of the nanostructures is in the range of 6–8 nm, which is in agreement with that obtained from XRD. It is interesting to note that ZnO nanostructured materials, as prepared by the radiolytic method, exhibit strong room-temperature fluorescence.     

Functionalization of Multi‐Walled Carbon Nanotubes by Electrografting of Polyacrylonitrile

Summary: Multi‐walled carbon nanotubes (MWNTs) have been successfully modified with polyacrylonitrile (PAN) by a cathodic electrochemical process. The surface‐modified MWNTs afforded are then dispersible in good solvents for PAN, such as N,N‐dimethylformamide (DMF). Collected from a dilute dispersion, these MWNTs are essentially disentangled, as confirmed by transmission electron microscopy (TEM) analysis. From the differential scanning calorimetry (DSC) traces for polyacrylonitrile and polyacrylonitrile‐grafted MWNTs, the maximum grafting ratio is estimated at 0.28.

Electrochemical grafting of polyacrylonitriles onto the surface of multi‐walled carbon nanotubes.     

SiO2 coated Fe3O4 magnetic nanoparticle dispersed multiwalled carbon nanotubes based amperometric glucose biosensor

A new type of amperometric glucose biosensor based on silicon dioxide coated magnetic nanoparticle decorated multiwalled carbon nanotubes (Fe₃O₄@SiO₂/MWNTs) on a glassy carbon electrode (GCE) has been developed. MWNTs have been synthesized by catalytic chemical vapour decomposition (CCVD) of acetylene over rare earth (RE) based AB₃ alloy hydride catalyst. The as-grown MWNTs have been purified and further functionlized. Functionalized MWNTs have been decorated with magnetic Fe₃O₄ nanoparticles which have been uniformly coated with biocompatible SiO₂ using a simple chemical reduction method. The characterization of magnetic nanoparticle modified MWNTs have been done by X-ray diffraction (XRD), Fourier transform infra red spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM), vibrating sample magnetometer (VSM), energy dispersive X-ray analysis (EDX) and UV-vis spectroscopy. Amperometric biosensor has been fabricated by the deposition of glucose oxidase (GOD) over Nafion-solubilized Fe₃O₄@SiO₂/MWNTs electrode. The resultant bioelectrode retains its biocatalytic activity and offers fast and sensitive glucose quantification. The performance of the biosensor has been studied using cyclic voltammetry and amperometry and the results have been discussed. The fabricated glucose biosensor exhibits a linear response from 1 μM to 30 mM with an excellent detection limit of 800 nM indicating the potential applications in food industries.