熔盐法制备Ca0.9La0.2/3Cu3Ti4O12陶瓷粉体及其介电性能研究

以CaCO3,CuO,TiO2,La2O3为反应物,NaCl,KCl为熔盐,通过熔盐法分别在700、750、800、850℃条件下合成Ca0.9La0.2/3Cu3Ti4O12陶瓷粉体。利用XRD和SEM分别对陶瓷粉体的物相结构和微观形貌进行了分析,并对其介电性能进行了测试。实验结果表明,随着合成温度的升高,陶瓷粉体的钙钛矿相含量逐渐增大,与传统固相法相比,熔盐法制备的粉体无团聚现象,耗时少。Ca0.9La0.2/3Cu3Ti4O12粉体制备的陶瓷在1 000℃烧结、测试频率在100 Hz~10 kHz时,获得优良的介电性能:介电常数大大超过104,介电损耗在0.1~0.47之间。     

Bi2Ti2O7薄膜的自组装法制备及表征

以Bi(NO3)3·5H2O和Ti(OC4H9)4为原料,采用自组装单层膜技术,在负载有功能化三氯十八烷基硅烷(octadecyl-trichloro-silane,OTS)的FTO基板上制备了Bi2Ti2O7薄膜。基板表面的亲水性测试表明,紫外照射使OTS自组装单层膜表面由疏水转变为亲水,实现功能化。借助X射线衍射(XRD)、X射线能量色散谱(EDS)、扫描电子显微镜(SEM)和原子力显微镜(AFM)分析分别对Bi2Ti2O7薄膜的组成、结构和微观形貌进行了表征。结果表明,沉积溶液浓度为0.02 mol·L-1时,所得Bi2Ti2O7薄膜均匀致密。560℃热处理1 h、厚度为0.4μm的Bi2Ti2O7薄膜在100 kHz的介电常数为153,介电损耗为0.089。     

试验优化设计Er3+-Yb3+共掺杂Gd2Ti2O7上转换发光特性

采用溶胶-凝胶(Sol-gel)法制备了Er~(3+)-Yb~(3+)共掺杂Gd2Ti2O7纳米晶粉末,通过试验优化设计的理论建立了Er~(3+)-Yb~(3+)掺杂浓度与发光强度的回归方程,利用遗传算法优化计算出方程的最优解Er~(3+)、Yb~(3+)掺杂浓度分别为5.60%(物质的量分数)和13.43%。Er~(3+)-Yb~(3+)共掺杂Gd2Ti2O7纳米晶粉末为单一面心立方Gd2Ti2O7相结构,随Yb~(3+)共掺杂浓度增加,X射线衍射峰逐渐向高角偏移。在976 nm激光激发下,Er~(3+)-Yb~(3+)共掺杂Gd2Ti2O7获得了分别对应于Er~(3+)的2H11/2/4S3/2→4I15/2和4F9/2→4I15/2跃迁的绿色和红色上转换发光,且绿色和红色发光均为双光子吸收过程。研究了最优样品上转换发光与温度之间的关系,发现绿色上转换发光具有优良的温度传感特性,对红色上转换发光的温度猝灭进行了解释。     

新型纳米结构V10O24·12H2O的制备及结构表征

以V2O5粉末为原料, 在常压下制备新型纳米结构V10O24·12H2O材料, 并分析了其反应机制. 利用XRD, TEM, TG-DSC, FTIR和XPS对其结构和形貌等进行了表征. 结果表明, V10O24·12H2O的层间距d(002)≈1.43 nm; 微观形貌为球形, 球径40~60 nm; 有V4+和V5+两种化学状态; IR峰的变化主要由晶格膨胀和V4+引起; 存在吸附水、层间水及结晶水.     

Y2O3/ZrO2中空纤维陶瓷膜的制备与表征

本文结合相转化技术和干湿法纺丝工艺制备了以YSZ(以摩尔分数为8%的Y2O3稳定的ZrO2)为原料的中空纤维陶瓷膜, 考察了YSZ粉体的粒度分布和形貌, 并研究了YSZ中空纤维陶瓷膜的气密性、 孔特性、 机械性能、 微观结构及晶型变化等.     

ZrB2/SiC前驱体的制备、表征及裂解行为

以聚锆氧烷为锆源,聚硼硅氮烷兼作硼源、硅源和碳源,通过共混得到ZrB2/SiC液相前驱体,该前驱体经高温裂解得到ZrB2/SiC复相陶瓷.对ZrB2/SiC前驱体的裂解行为、陶瓷产物结构及微观形貌进行了表征.结果表明,ZrB2/SiC前驱体经1400℃裂解后保持无定形状态,1500℃处理后析出t-ZrO2晶体,1600℃时体系发生碳热还原反应生成ZrC,同时析出SiC晶体,1700℃时生成ZrB2,最终陶瓷产物晶相组成为ZrB2/SiC.在1500~2000℃范围内,随着处理温度的升高,陶瓷由致密结构变为多孔结构,最终陶瓷产物由尺寸为100~300 nm的纳米颗粒堆积而成,各元素分布均匀.     

Bi4(Ti1/3Sn2/3)3O12掺杂BaTiO3基X8R陶瓷微观结构与介电性能

研究了Bi4(Ti1/3Sn2/3)3O12掺杂对钛酸钡基陶瓷微观结构和介电性能影响。结果表明,掺杂Bi4(Ti1/3Sn2/3)3O12后钛酸钡基陶瓷晶粒明显长大,同时烧结温度可由1 280℃降低至1 180℃。系统的介电性能和Bi4(Ti1/3Sn2/3)3O12的掺杂量有密切关系。当Bi4(Ti1/3Sn2/3)3O12的掺杂量从0.5mol%增加到2mol%,体系的居里峰被明显压低和展宽,当掺杂量为2mol%时居里峰变得不明显。当Bi4(Ti1/3Sn2/3)3O12的掺杂量从0.5mol%增加到2mol%,系统的居里温度由131℃升高至139℃。当Bi4(Ti1/3Sn2/3)3O12的掺杂量为1mol%时,钛酸钡基陶瓷介电常数为1 930,介电常数温度变化率为5%(-55℃),13%(134℃),-8%(150℃),满足X8R标准。     

NiFe2O4与TiO2稳定的多重Pickering乳液的制备

由沉淀法和溶胶-凝胶法分别制备了Ni Fe_2O_4和Ti O_2,并用XRD和SEM对两种粒子进行了表征,结果表明成功制备了粒径大小较为均匀的目标产物。用CTAB对Ni Fe_2O_4进行了改性,并由IR和Zeta电位测试予以确认。以改性Ni Fe_2O_4和Ti O_2作为稳定粒子,由两步法制备了W/O/W型多重Pickering乳液,采用数码照片和光学显微照片观察所制备的乳液的宏观与微观形貌。研究表明,制备的单重Pickering乳液粒径较为均匀,多重Pickering乳液粒径范围稍宽,但两者稳定性能都非常良好。     

USP制备高光电活性Ti掺杂Fe2O3薄膜

本文报道了采用超声喷雾裂解法(USP)法制备α-Fe2O3以及不同厚度的Ti掺杂α-Fe2O3薄膜,并通过XRD、XPS、SEM、IPCE表征了合成的薄膜。XRD测试结果表明,Ti掺杂和纯相Fe2O3均为α相并在(110)晶面优先生长;从AFM图中看出Fe2O3晶粒呈尖峰状垂直于平面排列;由XPS分析得知Ti离子在Fe2O3薄膜中以Ti4+和Ti3+两个价态存在;由光电效率表征可知,吸收光电转换效率(APCE)值是随着样品薄膜厚度增加而减小,在厚度为20nm时APCE为58%,对于粉末Fe2O3光催化材料是粒径尺寸越小光利用率越高;然而Fe2O3薄膜的IPCE值在厚度为60nm时最高达到23.5%,此时光利用效率最大。     

微波辅助制备CdS插层K2La2Ti3O10复合物及其光催化制氢的性能

采用微波辅助通过酸交换、胺柱撑、离子交换等步骤制备了CdS插层的K2La2Ti3O10(记做CdS-K2La2Ti3O10)复合光催化剂.利用X射线粉末衍射(XRD),场发射扫描电子显微镜(SEM),紫外-可见漫反射吸收光谱(UV-Vis)和光致发光光谱(PL)等对产物进行表征,考察了CdS-K2La2Ti3O10在紫外光及可见光下催化制氢活性.结果表明,微波辅助法与传统法制备的插层复合催化剂晶型结构相似,同时大大减少了离子交换反应时间,减少了对层间结构的破坏,拓展了催化剂的可见光吸收范围.微波辅助制备的催化剂在紫外光和可见光照射3 h后的产氢量分别为221.53 mmol/(g cat.)和3.23 mmol/(g cat.),并对光催化机理进行了分析.     

葡萄糖在Ti/NanoTiO2-ZrO2修饰电极上电催化氧化

在无水乙醇和乙酰丙酮混合溶液中,电解Ti金属制得前驱体Ti(OCH2CH3)4-y(acac)y,再加入ZrCl4,将上述溶液直接水解、干燥后,在450℃煅烧2 h,粉体通过X射线衍射(XRD)分析表明:纳米TiO2-ZrO2粉体呈单分散结构。扫描电子显微镜(SEM)测试表明,颗粒平均尺寸为30~40 nm。通过溶胶-凝胶法制得高活性的Ti/NanoTiO2-ZrO2修饰电极,采用循环伏安研究发现,Ti/NanoTiO2-ZrO2电极对葡萄糖氧化具有高催化活性。在NaBr电解液中,Br-在Ti/NanoTiO2-ZrO2电极表面氧化为Br2,Br2间接电氧化葡萄糖。     

ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

The disordered cubic structure of Ca7Co3Ga5O18

The new mixed oxide having composition close to Ca₇Co₃Ga₅O₁₈ was synthesized from CaCO₃, Co₃O₄ and Ga₂O₃ at 1150 °C in air and studied by neutron and synchrotron X-ray powder diffraction, selected-area electron diffraction and high-resolution electron microscopy. The structure was refined, using time-of-flight (TOF) neutron powder diffraction data, in space group F432, with and Z=8, to R_F=0.7%. It is considerably disordered, with four different tetrahedral sites randomly occupied by Co and Ga atoms at a ratio of 1:2. The tetrahedra form a disordered (Co_1/3Ga_2/3)O₂ 3D-framework inside which isolated CoO₆ octahedra, surrounded by 8 Ca atoms, are located. The structure is related to the ordered structure of Ca₁₄Al₁₀Zn₆O₃₅. Electron diffraction patterns confirmed the symmetry and unit cell and revealed no diffuse scattering. High-resolution electron microscopy images showed the absence of extended structural defects.     

Polyol-mediated synthesis of Li4Ti5O12 nanoparticle and its electrochemical properties

Li₄Ti₅O₁₂ nanoparticles were precipitated from ethylene glycol solution of titanium tetra isopropoxide (Ti(O-iPr)₄) and Li₂O₂ by refluxing at 197 °C for 12 h. The obtained particles were filtered and dried at 100 °C for 12 h, and the dried powder samples were heated at 320, 500 and 800 °C for 3 h. The X-ray diffraction patterns of the obtained samples exhibited a good fit with the spinel phase. The field emission-SEM images of the dried powder sample and the samples heated at 320, 500 and 800 °C for 3 h showed a uniform spherical morphology with a particle size of 5, 8, 10 and 400 nm, respectively. According to the results of electrochemical testing, the dried powder sample and the samples heated at 320, 500, and 800 °C for 3 h showed initial capacities of 200, 310, 320, and 260 mA h/g, respectively, at a current density of 0.05 mA/cm². Nanosized (6–8 nm) particles with good crystallinity were obtained by controlling the synthesis conditions. The sample heated at 500 °C for 3 h exhibited a high capacity and an excellent rate capability over 60 cycles.     

溶剂热法合成In2S3/CuSe核壳结构粉体

本文以氯化铜、氯化铟、硫脲、亚硒酸以及硒粉为原料,乙二醇及乙二胺为溶剂,采用常压溶剂热法制备了硫化铟为核硒化铜为壳(In2S3/CuSe)的核壳结构复合粉体。主要探讨了反应温度、不同反应原料以及不同表面活性剂对产物物相以及形貌的影响。通过采用X射线衍射(XRD)、扫描电镜(SEM)对产物的物相、形貌以及组成进行了表征。实验结果表明:常压溶剂热条件下可以制备得In2S3/CuSe复合粉体,其最佳反应工艺参数是:于160℃下合成In2S3粉体为核,于100℃下合成包裹在In2S3表面的CuSe粉体从而获得In2S3/CuSe核壳结构复合粉。在该工艺参数下合成产物的形貌主要由圆球状颗粒组成,粉体的粒径分布在1~2μm。此外,本文也通过添加不同种类表面活性剂对产物的形貌进行了控制。     

共沉淀法制备的MnOx-CeO2在含NO气氛中氧化碳烟的研究

用共沉淀法制备的复合氧化物MnOx-CeO2,其程序升温氧化(TPO)结果显示,1 000 mL.m-3NO和10%O2条件下MnOx-CeO2对应的碳烟起燃温度Ti为250~303℃,远低于无催化剂时的Ti(402℃)及CeO2的Ti(334℃);也低于无NO下MnOx-CeO2的Ti(346~360℃);与MnOx的Ti(290℃)相当,但MnOx-CeO2的Tm(413~441℃)仍比MnOx的Tm(441℃)稍低。明显地,NO促进了碳烟的氧化,MnOx-CeO2比CeO2和MnOx的活性都要高。NO-TPD、FT-IR及原位DRIFTs表明,MnOx-CeO2表面对NO吸附能力强,更易促进NO氧化和NOx储存,从而有利于碳烟的氧化。可能的机理为,富氧条件下气相O2推动催化剂中氧物种(如超氧O2-,化学弱吸附氧O-与晶格氧O2-)的形成(含相互转化)与迁移,推进了NO或NO2-的氧化;储存的NOx在低温下生成硝酸根离子,在高温时则释放出高活性的NO2*和O-,促进碳烟氧化,其中间产物包括C-NO2复合物与C(O)复合物。     

In2O3八面体的碳还原法制备及其发光性能研究

In₂O₃ octahedrons were synthesized by carbothermal reduction using In₂O₃ nanoparticles as the source material. The as-synthesized products were characterized by X-ray powder diffraction (XRD), energy dispersive X-ray(EDX), scanning electron microscopy(SEM), transmission electron microscopy(TEM), high-resolution transmission electron microscopy (HRTEM), selected-area electron diffraction analysis(SAED) and Room-temperature photoluminescence(PL) spectroscopy. The results show that the products are single-crystalline In₂O₃ octahedrons, the length of the octahedrons is in the range of 400～3 000 nm; the PL patterns display two peaks located at 447nm and 555 nm upon excitation at 380 nm, and the other two peaks located at 444 nm and 550 nm upon excitation at 325 nm; the excitation pattern shows two peaks located at 274 nm and 371 nm, respectively. The growth mechanism of the In₂O₃ octahedrons is discussed, and the high supersaturation ratio is considered as the key factor.     

Ti掺杂的MgH2和Mg2NiH4的放氢性能

以TiF₃和Ti(OBu-n)₄为催化剂, 研究了Ti离子掺杂对MgH₂和Mg₂NiH₄放氢性能的影响. 结果表明, 未掺杂的MgH₂起始放氢温度为420 ℃, 掺杂TiF₃和Ti(OBu-n)₄后分别降低到360和410 ℃; Mg₂NiH₄在掺杂TiF₃后放氢温度由230 ℃降低到220 ℃, 而掺杂Ti(OBu-n)₄后没有变化. 可见无论对MgH₂或Mg₂NiH₄, 在降低放氢温度方面TiF₃都明显优于Ti(OBu-n)₄. 另外, 研究还发现, TiF₃掺杂对MgH₂放氢动力学有显著的提高, 但对Mg₂NiH₄没有明显的提高. 结合XRD和FTIR的测试分析, 我们认为: 催化作用很大程度上取决于氢化物自身的晶体结构和催化剂的电子结构; 降低氢化物放氢温度和提高动力学性能的原因是催化剂与氢化物之间的相互作用削弱了氢化物中Mg—H或Ni—H键, 使得活泼的H…H原子对容易形成, 从而有利于H₂的释出.     

Transport coefficients of titanium-doped Sb2Te3 single crystals

Titanium-doped single crystals (c_Ti=0-2×10²⁰ atoms cm⁻³) were prepared from the elements Sb, Ti, and Te of 5 N purity by a modified Bridgman method. The obtained crystals were characterized by measurements of the temperature dependence of the electrical resistivity, Hall coefficient, Seebeck coefficient and thermal conductivity in the temperature range of 3-300 K. It was observed that with an increasing Ti content in the samples the electrical resistivity, the Hall coefficient and the Seebeck coefficient increase. This means that the incorporation of Ti atoms into the Sb₂Te₃ crystal structure results in a decrease in the concentration of holes in the doped crystals. For the explanation of the observed effect a model of defects in the crystals is proposed. The data of the lattice thermal conductivity were fitted well assuming that phonons scatter on boundaries, point defects, charge carriers, and other phonons.